Mode competition in streamwise-only vortex induced vibrations

Time-resolved Particle-Image Velocimetry (PIV) has been used to study mode competition and transient behaviour in the wake of a cylinder experiencing Vortex-Induced Vibrations (VIV) in the streamwise direction. The cylinder response regime contained two branches, occurring above and below the onset of synchronisation between the wake and the cylinder motion (lock-in). During the first branch, the wake exhibited both the S-I mode (in which two vortices are shed simultaneously per vibration cycle) and the alternate A-II mode (similar to the well known von Kármán vortex street). An extended PIV data set acquired in this region revealed mode switching between the S-I and A-II modes. A criterion based on Proper-Orthogonal Decomposition was developed to identify which mode was dominant as a function of time. The A-II mode was found to be dominant for over 90% of the instantaneous fields examined, while the S-I mode appeared to be more unstable.Symmetrically shed vortices were found to rearrange downstream into an alternate structure in which the wake was no longer synchronised to the cylinder motion. The dominant frequency of transverse velocity fluctuations was measured throughout the wake in order to study the effects of this breakdown in more detail. For the majority of the wake, the fluctuations occurred at the Strouhal frequency, while in a region in the near wake the fluctuations occurred at the frequency of the cylinder motion. It is thought that during the first response branch vortices are formed at the cylinder response frequency, but tend to quickly rearrange downstream into an alternate structure which is no longer synchronised to the cylinder motion. As a result, the fluctuating drag will be synchronised to the structural motion, and is capable of providing positive energy transfer in the apparent absence of lock-in. Finally, the spatial dependence of the frequency of velocity fluctuations throughout the wake is used to explain some of the conflicting results in the literature regarding streamwise VIV, and the implications for the general study of VIV are discussed.     

Resonance in flow past oscillating cylinder under subcritical conditions

Flow around an oscillating cylinder in a subcritical region are numerically studied with a lattice Boltzmann method(LBM). The effects of the Reynolds number,oscillation amplitude and frequency on the vortex wake modes and hydrodynamics forces on the cylinder surface are systematically investigated. Special attention is paid to the phenomenon of resonance induced by the cylinder oscillation. The results demonstrate that vortex shedding can be excited extensively under subcritical conditions, and the response region of vibration frequency broadens with increasing Reynolds number and oscillation amplitude. Two distinct types of vortex shedding regimes are observed. The first type of vortex shedding regime(VSR I) is excited at low frequencies close to the intrinsic frequency of flow, and the second type of vortex shedding regime(VSR II)occurs at high frequencies with the Reynolds number close to the critical value. In the VSR I, a pair of alternately rotating vortices are shed in the wake per oscillation cycle,and lock-in/synchronization occurs, while in the VSR II, two alternately rotating vortices are shed for several oscillation cycles, and the vortex shedding frequency is close to that of a stationary cylinder under the critical condition. The excitation mechanisms of the two types of vortex shedding modes are analyzed separately.     

Symmetric vortex shedding in the near wake of a circular cylinder due to streamwise perturbations

Symmetric perturbations imposed on cylinder wakes may result in a modification of the vortex shedding mode from its natural antisymmetric, or alternating, to a symmetric one where twin vortices are simultaneously shed from both sides of the cylinder. In this paper, the symmetric mode in the wake of a circular cylinder is induced by periodic perturbations imposed on the in-flow velocity. The wake field is examined by PIV and LDV for Reynolds numbers about 1200 and for a range of perturbation frequencies between three and four times the natural shedding frequency of the unperturbed wake. In this range, a strong competition between symmetric and antisymmetric vortex shedding occurs for the perturbation amplitudes employed. The results show that symmetric formation of twin vortices occurs close to the cylinder synchronized with the oscillatory component of the flow. The symmetric mode rapidly breaks down and gives rise to an antisymmetric arrangement of vortex structures further downstream. The downstream wake may or may not be phase-locked to the imposed oscillation. The number of cycles for which the symmetric vortices persist in the near wake is a probabilistic function of the perturbation frequency and amplitude. Finally, it is shown that symmetric shedding is associated with positive energy transfer from the fluid to the cylinder due to the fluctuating drag.     

Three-dimensional numerical simulation of vortex-induced vibration of an elastically mounted rigid circular cylinder in steady current

Vortex-induced vibration (VIV) of an elastically mounted rigid circular cylinder in steady current is investigated by solving the three-dimensional Navier–Stokes equations. The cylinder is allowed to vibrate only in the cross-flow direction. The aim of this study is to investigate the variation of the vortex shedding flow in the axial direction of the cylinder and to study the transition of the flow from two-dimensional (2D) to three-dimensional (3D) for VIV of a cylinder. Simulations are carried out for a constant mass ratio of 2, the Reynolds numbers ranging from 150 to 1000 and the reduced velocities ranging from 2 to 12. The three-dimensionality of the flow is found to be the strongest in the upper branch of the VIV response and weakest in the initial branch. The 2S and 2P vortex shedding modes are found to coexist along the cylinder span in the upper branch, leading to strong variations of the lift coefficient in the axial direction of the cylinder. The difference between the flow transition from 2D to 3D in the VIV lock-in regime and that in the wake of a stationary cylinder is identified. The transition mode B found in the wake of a stationary cylinder is also found in the wake of a vibrating cylinder. The critical Reynolds number for flow transition from 2D to 3D of a cylinder undergoing cross-flow VIV at a reduced velocity of 6 is found to be greater than that for a stationary cylinder. For a constant reduced velocity of 6, the wake flow changes from 2D to 3D as the Reynolds number is increased from 250 to 300. Some 2D numerical simulations are performed and it is found that the 2D Navier–Stokes (NS) equations are not able to predict the VIV in the turbulent flow regime, while the 2D Reynolds-averaged Navier–Stokes (RANS) equations improve the results.     

Numerical simulation of two-degree-of-freedom vortex-induced vibration of a circular cylinder close to a plane boundary

Two-degree-of-freedom vortex-induced vibrations (VIV) of a circular cylinder close to a plane boundary are investigated numerically. The Reynolds-Averaged Navier-Stokes (RANS) equations are solved using the Arbitrary Lagrangian Eulerian (ALE) scheme with a k-ω turbulence model closure. The numerical model is validated against experimental data of VIV of a cylinder in uniform flow and VIV of a cylinder close to a plane boundary at low mass ratios. The numerical results of the vibration mode, vibration amplitude and frequency agree well with the experimental data. VIV of a circular cylinder close to a plane boundary is simulated with a mass ratio of 2.6 and gap ratios of e/D=0.002 and 0.3 (gap ratio is defined as the ratio of gap between the cylinder and the bed (e) to cylinder diameter (D)). Simulations are carried out for reduced velocities ranging from 1 to 15 and Reynolds numbers ranging from 1000 to 15 000. It is found that vortex-induced vibrations occur even if the initial gap ratio is as small as e/D=0.002, although reported research indicated that vortex shedding behind a fixed circular cylinder is suppressed at small gap ratios (e/D<0.3 or 0.2). It was also found that vibration amplitudes are dependant on the bouncing back coefficient when the cylinder hits the plane boundary. Three vortex shedding modes are identified according to the numerical results: (i) single-vortex mode where the vortices are only shed from the top of the cylinder; (ii) vortex-shedding-after-bounce-back mode; (iii) vortex-shedding-before-bounce-back mode. It was found that the vortex shedding mode depends on the reduced velocity.     

单窄条控制件对横向振荡柱体尾流 2P模式 旋涡脱落的改变

横向强迫振荡柱体尾流控制是柱体涡激振动控制的基础,在海洋、土木等工程中具有重要意义. 横向强迫振荡柱体尾流中存在一种锁频旋涡脱落模式,即在一个振荡周期内柱体上、下侧各脱落旋转方向相反的一对涡,称为2P模式. 本文将相对宽度b/D=0.32的窄条控制件置于横向强迫振荡柱体下游,对振幅比A/D=1.25, 无量纲振频f_e D/V_∞=0.22,雷诺数Re=1 200的2P模式旋涡脱落进行干扰,并通过改变控制件位置,研究旋涡的变化规律. 采用二维大涡模拟和实验验证方法进行研究,在控制件位置范围0.8≤X/D≤3.2, 0.4≤Y/D≤3.2内,得到了2P, 2S, P+S和另外6种新发现的旋涡脱落模式,并对各模式旋涡的形成过程作了详细描述. 在控制件位置平面上给出了各旋涡模式的存在区域,画出了旋涡脱落强度的等值线图,并发现在一个相当大的区域内,旋涡脱落强 度可减小一半以上,尾流变窄. 发现柱体大幅振荡引起的横向剪切流在旋涡生成中起关键作用. 探讨了控制件对横向剪切流的影响,分析了控制件在每种旋涡模式形成中的作用机制.      

URANS vs. experiments of flow induced motions of multiple circular cylinders with passive turbulence control

Two-dimensional Unsteady Reynolds-Average Navier–Stokes equations with the Spalart–Allmaras turbulence model are used to simulate the flow induced motions of multiple circular cylinders with passive turbulence control (PTC) in steady uniform flow. Four configurations with 1, 2, 3, and 4 cylinders in tandem are simulated and studied at a series of Reynolds numbers in the range of 30 000<Re<120 000. Simulation results are verified by experimental data measured in the Marine Renewable Energy Laboratory. Good agreement was observed between the values of vorticity, amplitude ratio, and frequency ratio predicted by numerical simulations and experimental measurements. The amplitude and frequency response show the initial and upper branches in vortex induced vibration (VIV), transition from VIV to galloping, and galloping branch for all PTC-cylinders. The maximum amplitude of 2.9 diameters for the first cylinder is achieved at Re=104 356 in the numerical results. Compared with the first cylinder, the VIV initial branch starts at higher Re for the downstream cylinders due to the presence of the upstream cylinder(s). 2P and 2P+2S vortex patterns are observed at Re=62 049 and Re=90 254 for the single PTC-cylinder. Furthermore, the shed vortices of the downstream cylinders are strongly disrupted and modified by the vortices shed from the upstream one in the cases of multiple PTC-cylinders.     

Wake dynamics of external flow past a curved circular cylinder with the free-stream aligned to the plane of curvature

The fundamental mechanism of vortex shedding past a curved cylinder has been investigated at a Reynolds number of 100 using three-dimensional spectral/hp computations. Two different configurations are presented herein: in both cases the main component of the geometry is a circular cylinder whose centreline is a quarter of a ring and the inflow direction is parallel to the plane of curvature. In the first set of simulations the cylinder is forced to transversely oscillate at a fixed amplitude, while the oscillation frequency has been varied around the Strouhal value. Both geometries exhibit in-phase vortex shedding, with the vortex cores bent according to the body's curvature, although the wake topology is markedly different. In particular, the configuration that was found to suppress the vortex shedding in absence of forced motion exhibits now a primary instability in the near wake. A second set of simulations has been performed imposing an oscillatory roll to the curved cylinder, which is forced to rotate transversely around the axis of its bottom section. This case shows entirely different wake features from the previous one: the vortex shedding appears to be out-of-phase along the body's span, with straight cores that tend to twist after being shed and manifest a secondary spanwise instability. Further, the damping effect stemming from the transverse planar motion of the part of the cylinder parallel to the flow is no longer present, leading to a positive energy transfer from the fluid to the structure.     

Flow-induced vibrations of a tethered circular cylinder

One of the most basic examples of fluid-structure interaction is provided by a tethered body in a fluid flow. The tendency of a tethered buoy to oscillate when excited by waves is a well-known phenomenon; however, it has only recently been found that a submerged buoy will act in a similar fashion when exposed to a uniform flow at moderate Reynolds numbers, with a transverse peak-to-peak amplitude of approximately two diameters over a wide range of velocities. This paper presents results for the related problem of two-dimensional simulations of the flow past a tethered cylinder. The coupled Navier–Stokes equations and the equations of motion of the cylinder are solved using a spectral-element method. The response of the tethered cylinder system was found to be strongly influenced by the mean layover angle as this parameter determined if the oscillations would be dominated by in-line oscillations, transverse oscillations or a combination of the two. Three branches of oscillation are noted, an in-line branch, a transition branch and a transverse branch. Within the transition branch, the cylinder oscillates at the shedding frequency and modulates the drag force such that the drag signal is dominated by the lift frequency. It is found that the mean amplitude response is greatest at high reduced velocities, i.e., when the cylinder is oscillating predominantly transverse to the fluid flow. Furthermore, the oscillation frequency is synchronized to the vortex shedding frequency of a stationary cylinder, except at very high reduced velocities. Visualizations of the pressure and vorticity in the wake reveal the mechanisms behind the motion of the cylinder.     

Vortex shedding flow behind a slowly rotating circular cylinder

This paper investigates flow past a rotating circular cylinder at 3600?Re?5000 and α?2.5. The flow parameter α is the circumferential speed at the cylinder surface normalized by the free-stream velocity of the uniform cross-flow. With particle image velocimetry (PIV), vortex shedding from the cylinder is clearly observed at α<1.9. The vortex pattern is very similar to the vortex street behind a stationary circular cylinder; but with increasing cylinder rotation speed, the wake is observed to become increasing narrower and deflected sideways. Properties of large-scale vortices developed from the shear layers and shed into the wake are investigated with the vorticity field derived from the PIV data. The vortex formation length is found to decrease with increasing α. This leads to a slow increase in vortex shedding frequency with α. At α=0.65, vortex shedding is found to synchronize with cylinder rotation, with one vortex being shed every rotation cycle of the cylinder. Vortex dynamics are studied at this value of α with the phase-locked eduction technique. It is found that although the shear layers at two different sides of the cylinder possess unequal vorticity levels, alternating vortices subsequently shed from the cylinder to join the two trains of vortices in the vortex street pattern exhibit very little difference in vortex strength.     

Numerical investigation on vortex-induced vibration of an elastically mounted circular cylinder at low Reynolds number using the fictitious domain method

A direct numerical simulation of two-dimensional (2D) flow past an elastically mounted circular cylinder at low Reynolds number using the fictitious domain method had been undertaken. The cylinder motion was modelled by a two degree-of-freedom mass–spring–damper system. The computing code was verified against a benchmark problem in which flow past a stationary circular cylinder is simulated. Then, analyses of vortex-induced vibration (VIV) responses, drag and lift forces and the phase and vortex structures were carried out. Results show that the cylinder's non-dimensional cross-flow response amplitude reaches its summit of 0.572 in the ‘lock-in’ regime. The ‘2S’, instead of the ‘2P’, vortex shedding mode is dominated in the ‘lower’ branch for this 2D low-Re VIV. A secondary oscillation is observed in the lift force when ‘lock-in’ occurs. It is shown that this secondary component changes the phase, offset the energy input by the primary component and thus reduces the cylinder responses. Effects of the Skop–Griffin parameter on cylinder responses were also investigated.     

An experimental investigation on vortex induced vibration of a flexible inclined cable under a shear flow

In the present study, an experimental investigation was performed to characterize the vortex induced vibration (VIV) of a flexible cable in an oncoming shear flow. The VIV tests were conducted in a wind tunnel with a flexible cable model. It was found that, under different oncoming velocity profiles, the cable model behaved in single-mode and multi-mode VIVs. The displacement amplitudes of the single mode VIVs were found to be larger than those of multi-mode VIVs, and the cross-flow (CF) response was larger than that of in-line (IL) direction for either the single mode or multi-mode VIVs. For a single mode vibration, the largest CF response occurs in the 1st mode VIV, and the motion trajectory of the 1st mode VIV was found to be an inclined figure of eight shape, while other single mode VIVs behaved in ellipse or straight line trajectories. For multi-mode VIVs, no stable vibration trajectories were found to exist since the vibration frequency bands covered two or more vibration modes. The vortex-shedding frequencies in the wake behind the inclined cable were also characterized in the present study. The shedding frequencies of the wake vortices were found to coincide well with the vibration modes: for a single mode VIV, they were close to the dominant vibration mode; for a multi-mode VIV, they could also cover the appearing vibration modes.     

Vibrations of a cylinder in a uniform flow in the presence of a no-slip side-wall

A circular cylinder placed in a uniform flow, and that spans the entire length between two side walls, may experience either parallel or oblique vortex shedding depending on the end conditions. It was shown by Mittal and Sidharth (2014) that the spatio-temporal periodicity of the oblique vortex shedding results in constant-in-time force experienced by the cylinder. On the contrary, parallel vortex shedding leads to fluid force that fluctuates with time. The free vibrations of a circular cylinder, in the presence of a wall, are investigated. For comparison, computations with end walls, where a slip condition on velocity is specified, are also carried out. The Reynolds number, based on the diameter of the cylinder and free-stream speed of the flow, is Re=100. The initial condition for the free vibrations is the fully developed unsteady flow past a stationary cylinder with oblique shedding. It is found that as the amplitude of vibration of the cylinder builds up, the vortices shed from the cylinder align with its axis leading to parallel shedding. The response of the cylinder is associated with two branches: initial and lower. On the lower branch, the response of the cylinder is virtually identical from two- and three-dimensional computations. The flow as well as the response is different on the initial branch and outside the synchronization regime. Forced vibrations confirm the phenomena.     

Active vortex-induced vibration control of a circular cylinder at low Reynolds numbers using an adaptive fuzzy sliding mode controller

An adaptive fuzzy sliding mode control (AFSMC) scheme is applied to actively suppress the two-dimensional vortex-induced vibrations (VIV) of an elastically mounted circular cylinder, free to move in in-line and cross-flow directions. Laminar flow regime at Re=90, low non-dimensional mass with equal natural frequencies in both directions, and zero structural damping coefficients, are considered. The natural oscillator frequency is matched with the vortex shedding frequency of a stationary cylinder at Re=100. The strongly coupled unsteady fluid/cylinder interactions are captured by implementing the moving mesh technology through integration of an in-house developed User Define Function (UDF) into the main code of the commercial CFD solver Fluent. The AFSMC approach comprises of a fuzzy system designed to mimic an ideal sliding-mode controller, and a robust controller intended to compensate for the difference between the fuzzy controller and the ideal one. The fuzzy system parameters as well as the uncertainty bound of the robust controller are adaptively tuned online. A collaborative simulation scheme is realized by coupling the control model implemented in Matlab/Simulink to the plant model constructed in Fluent, aiming at determination of the transverse control force required for complete suppression of the cylinder streamwise and cross-flow oscillations. The simulation results demonstrate the high performance and effectiveness of the adopted control algorithm in attenuating the 2D-VIV of the elastic cylinder over a certain flow velocity range. Also, the enhanced transient performance of the AFSM control strategy in comparison with a conventional PID control law is demonstrated. Furthermore, the effect of control action on the time evolution of vortex shedding from the cylinder is discussed. In particular, it is observed that the coalesced vortices in the far wake region of the uncontrolled cylinder, featuring the C(2S)-type vortex shedding characteristic mode, are ultimately forced to switch to the classical von Kármán vortex street of 2S-type mode, displaying wake vortices of moderately weaker strengths very similar to those of the stationary cylinder. Lastly, robustness of AFSMC is verified against relatively large structural uncertainties as well as with respect to a moderate deviation in the uniform inlet flow velocity.     

Numerical simulation of vortex-induced vibration of a circular cylinder at low mass-damping using RANS code

Fundamental research on vortex-induced vibration (VIV) of a circular cylinder is still needed to build more rational VIV analysis tools for slender marine structures. Numerical results are presented for the response of an elastically mounted rigid cylinder at low mass damping constrained to oscillate transversely to a free stream. A two-dimensional Reynolds-averaged Navier–Stokes (RANS) code equipped with the SST k−ω turbulence model is applied for the numerical calculations. The numerical results are compared in detail with recent experimental and computational work. The Reynolds-averaging procedure erases the random disturbances in the vortex shedding process, so that the comparison between experimental data and the numerical results obtained by RANS codes may reveal some random characteristics of the VIV response. How random disturbance affects the observation in the experiments is discussed in this paper and the issues influencing the appearance of the upper branch in experiments are especially investigated. The absence of the upper branch in RANS simulations is explained in depth on account of discrepancies, which exist between experiments and RANS simulations. In addition, the formation of the 2P vortex shedding mode and its transition through the lock-in region are well reproduced in this investigation.     

An experimental investigation of flow past a dual step cylinder

Flow development in the wake of a dual step cylinder has been investigated experimentally using Laser Doppler Velocimetry and flow visualization. The dual step cylinder model is comprised of a large diameter cylinder (D) mounted at the mid-span of a small diameter cylinder (d). The experiments have been performed for a Reynolds number (Re _D ) of 1,050, a diameter ratio (D/d) of 2, and a range of large cylinder aspect ratios (L/D). The results show that the flow development is highly dependent on L/D. The following four distinct flow regimes can be identified based on vortex dynamics in the wake of the large cylinder: (1) for L/D ≥ 15, three vortex shedding cells form in the wake of the large cylinder, one central cell bounded by two cells of lower frequency, (2) for 8 < L/D ≤ 14, a single vortex shedding cell forms in the wake of the large cylinder, (3) for 2 < L/D ≤ 6, vortex shedding from the large cylinder is highly three-dimensional. When spanwise vortices are shed, they deform substantially and attain a hairpin shape in the near wake, (4) for 0.2 ≤ L/D ≤ 1, the large cylinder induces vortex dislocations between small cylinder vortices. The results show that for Regimes I to III, on the average, the frequency of vortex shedding in the large cylinder wake decreases with L/D, which is accompanied by a decrease in coherence of the shed vortices. In Regime IV, small cylinder vortices connect across the large cylinder wake, but these connections are interrupted by vortex dislocations. With decreasing L/D, the frequency of dislocations decreases and the dominant frequency in the large cylinder wake increases toward the small cylinder shedding frequency.     

Wake structures and vortex-induced vibrations of a long flexible cylinder—Part 2: Drag coefficients and vortex modes

Drag coefficients and vortex structures in the wake of a vertical long flexible cylinder vibrating at low mode numbers are presented in this paper. A model with an external diameter of 16 mm and a total length of 1.5 m giving an aspect ratio of about 94 was used to perform more than 100 runs in which Reynolds numbers ranged between 1200 and 12 000. Only the lower 40% of its length was exposed to the water current in the flume and applied top tensions varied from 15 to 110 N giving fundamental natural frequencies in the range from 3 to 7.1 Hz. Reduced velocities based on the fundamental natural frequency up to 16 were reached. The mass ratio was 1.8 and the combined mass-damping parameter about 0.05. The largest drag coefficients were found related to the largest x–y synchronised motions. Digital particle image velocimetry was used to investigate the vortex structures in the wake of the cylinder model. Two modes of vortex shedding were observed, depending on the response branch and the position along the length of the model at which the interrogations were performed.     

On the study of vortex-induced vibration of a cylinder with helical strakes

While the effect of helical strakes on suppression of Vortex-Induced Vibrations (VIV) has been studied extensively, the mechanism of VIV mitigation using helical strakes is much less well documented in the literature. In the present study, a rigid circular cylinder of diameter d=80 mm attached with three-strand helical strakes of dimensions of 10d in pitch and 0.12d in height was tested in a wind tunnel. It was found that the helical strakes can reduce VIV by about 98%. Unlike the bare cylinder, which experiences lock-in over the reduced velocity in the range of 5-8.5, the straked cylinder does not show any lock-in region. In exploring the mechanism of VIV reduction by helical strakes, measurements in stationary bare and straked cylinder wakes using both a single X-probe at four different Reynolds numbers, i.e. Re=10 240, 20 430, 30 610 and 40 800, and two X-probes with variable separations in the spanwise direction at Re=20 430 were conducted. It was found that vortices shed from the straked cylinder are weakened significantly. The dominate frequency varies by about 30% over the range of x/d=10-40 in the streamwise direction while that differs by about 37.2% of the averaged peak frequency over a length of 3.125d in the spanwise direction. The latter is supported by the phase difference between the velocity signals measured at two locations separated in the spanwise direction. The correlation length of the vortex structures in the bare cylinder wake is much larger than that obtained in the straked cylinder wake. As a result, the straked cylinder wake agrees more closely with isotropy than the bare cylinder wake. Flow visualization on the plane perpendicular to the cylinder axis at Reynolds number of about 300 reveals small-scale vortices in the shear layers of the straked cylinder wake. However, these vortices do not roll up and interact with each other to form the well-organized Karman-type vortices. Flow visualization on the plane parallel to the cylinder axis shows vortex dislocation and swirling flow, which should be responsible for the variations of the peak frequency in the streamwise as well as spanwise directions.     

PIV measurements of the wake behind a rotationally oscillating circular cylinder

The near-wake behind a circular cylinder undergoing rotational oscillatory motion with a relatively high forcing frequency has been investigated experimentally. Experiments were carried out varying the ratio of the forcing frequency f_f to the natural vortex shedding frequency f_n in the range of 0.0 (stationary) to 1.6 at an oscillation amplitude of θ_A=30° and Reynolds number of Re=4.14×10³. Depending on the frequency ratio (F_R=f_f /f_n), the near-wake flow could be divided into three regimes—non-lock-on (F_R=0.4), transition (F_R=0.8, 1.6) and lock-on (F_R=1.0) regimes—with markedly different flow structures. When the frequency ratio was less than 1.0 (F_R⩽1.0), the rotational oscillatory motion of the cylinder decreased the length of the vortex formation region and enhanced the mutual interaction between large-scale vortices across the wake centerline. The entrainment of ambient fluid seemed to play an important role in controlling the near-wake flow and shear-layer instability. In addition, strong vortex motion was observed throughout the near-wake region. The flow characteristics changed markedly beyond the lock-on flow regime (F_R=1.0) due to the high frequency forcing. At F_R=1.6, the high frequency forcing decreased the size of the large-scale vortices by suppressing the lateral extent of the wake. In addition, the interactions between the vortices shed from both sides of the cylinder were not so strong at this forcing frequency. As a consequence, the flow entrainment and momentum transfer into the wake center region were reduced. The turbulent kinetic energy was large in the region near the edge of the recirculation region, where the vortices shed from both sides of the cylinder cross the wake centerline for all frequency ratios except for the case of F_R=1.6. The temporally resolved quantitative flow information extracted in the present work is useful for understanding the effects of open-loop active flow control on the near-wake flow structure.     

Modes of vortex formation and transition to three-dimensionality in the wake of a freely vibrating cylinder

The present work is aimed to give some insight into the relation between vortex shedding modes and transition to three-dimensionality in the wake of a freely vibrating cylinder by establishing a numerical model and analyzing the relevant results of two- and three-dimensional simulations. The compressible flow past an elastically-mounted cylinder is solved by using the immersed boundary method (IB method). The cylinder is free to vibrate in the transverse direction with zero structure damping. The response of displacement amplitude is studied with the variation of reduced velocity. Whether P+S mode exists in three-dimensional flow and the occurrence of 2P mode is caused by flow transition from two-dimensional to three-dimensional are problems of concern. Both 2P and P+S wake modes are observed in two- and three-dimensional simulations. The numerical results indicate that the flow transition from two-dimensional to three-dimensional is coupled with the cylinder vibration in the synchronization/lock-in regime. The wake formation given by three-dimensional simulations suggests that the P+S mode might exist in reality when the flow is reverted to two-dimensional by vortex induced vibration (VIV) at Re=300–350. When Reynolds number increases to 425, the wake formation undergoes transition to three-dimensionality and 2P mode is observed. The effect of mass ratio on the flow transition to three-dimensionality is studied. The relationship between wake modes and aerodynamic forces is discussed.