Nonlinear oscillatory processes in wheeled vehicles

The free damped vibrations of a wheeled vehicle with independent suspension are analyzed with allowance for the nonlinear characteristics of the suspension springs and shock absorbers. The vibrations of a wheeled vehicle with a suspension with smooth nonlinear characteristics are studied for a model with seven degrees of freedoms. The skeleton curves and nonlinear normal modes are obtained. For a model with two degrees of freedoms (quarter-car) that corresponds to axisymmetric vibrations, the nonlinear normal modes are found in the case of a shock absorber with nonsmooth nonlinear characteristic     

Unsymmetrical nonlinear bending problem of circular thin plate with variable thickness

Introduction Manystructuralelements(pole,plate,shell)withunevenandvariablethicknessarewidely usedinallkindsofengineeringfields.Engineerscansavematerialswhentheydesignbecause theseelementshavebetteroptimizedshapeofstructuralfeature,butthisaddsdifficultytotheanalysisoftheirmechanicalcapability.Manypreviouspapers[1-4]havesolvedtheproblemof symmetricalaxis,butnobodyhassolvedtheunsymmetricalnonlineardeformationproblemof circularthinplatewithvariablethicknessandunsymmetricalaxisuptonow,afewworkonly …     

Simulations of free surface flows with implementation of surface tension and interface sharpening in the two-fluid model

Two-fluid model used for free surface flows with large characteristic scales is improved; the smeared interface is sharpened with conservative level set method and the surface tension force with wetting angle is implemented. Surface tension force is split between two phases with several models. Detailed analysis showed the splitting of surface tension force with volume averaging as the most appropriate. The improved two-fluid model with interface sharpening and implemented surface tension is validated on several test cases. The pressure jump over a droplet interface test case showed that the pressure jump in simulation converges with grid refinement to the analytical one. The parasitic currents in simulation are one order of magnitude larger than in simulation with volume of fluid model. In the oscillating droplet test case the time period of oscillating droplet with initially ellipsoid or square shape is similar to the analytical time period. In the rising bubble test case, the rising bubble position, terminal velocity, and circularity are similar to the one observed in simulations with level set model. The wetting angle is implemented in the two-fluid model with interface sharpening and surface tension force. Model is tested in the simulation of droplet in contact with wall with different wetting angles.     

金字塔栅格夹心夹层板动力响应分析

本文将金字塔形栅格夹心夹层板假设成均匀夹心夹层板，应用Reissner夹层板理论，对其自振频率以及在简谐荷载下的强迫振动进行了研究，并以简支板为例，得到其解析解，通过与有限元分析进行比较，两者结果吻合良好。并把金字塔形栅格夹层板与同质量实体板进行比较，得出金字塔形栅格夹层板具有更好动力性能。     

喜马拉雅山地区重大滑坡灾害及其与地层岩性的关系研究

位于青藏高原南部的喜马拉雅山地区,是高原隆升最快的地方,这里内外动力作用异常活跃,是我国重大滑坡灾害最严重的地区之一,重大滑坡灾害对国民经济和社会发展带来了极大危害。本文在对研究区的地质、地理背景进行了详细分析的基础上,利用遥感解译和实地调查相结合的手段,研究了该区重大滑坡灾害的分布及其与地层岩性的关系,将本区地层岩性大致划分为13个工程地质岩组:松散岩组、软弱岩组、软弱岩夹较软弱岩组、软弱岩夹较坚硬岩组、较软弱岩组、较软弱岩夹软弱岩组、较软弱岩夹较坚硬岩组、较软弱岩夹坚硬岩组、较坚硬岩与软弱岩互层岩组、较坚硬岩夹软弱岩岩组、较坚硬岩夹较软弱岩组、较坚硬岩组、坚硬岩组,发现重大滑坡更容易发生在软弱岩组、较硬岩夹较软弱岩组以及坚硬岩组中,而软弱岩夹较软弱岩组、较软弱岩夹较坚硬岩组中无重大滑坡灾害分布。重大滑坡灾害的上述分布特征,反映出地层岩性与重大滑坡灾害之间的复杂关系,一方面岩性软弱,比较容易发生滑坡灾害; 另一方面,岩性越坚硬,地形越高陡,也容易发生重大滑坡灾害。     

应力和位移约束下的板壳结构截面优化

将准则法和数学规划法相结合，根据满应力准则将应力约束化为动态下限，借助单位虚载荷法将位移约束转化为设计变量的近似显函数，建立了满足应力和位移约束的优化模型. 为了解决多变量的大型优化问题，根据对偶理论将上千设计变量的优化模型转化为几个变量的对偶模型，并通过二次规划求解. 以MSC/Nastran软件为结构分析的求解器，借助MSC/Patran软件为开发平台，完成了板壳结构截面优化程序. 程序完全和Patran及Nastran融为一体，在Patran中建立模型，利用Nastran分析计算，根据优化结果对设计变量调整，再用Nastran进行结构重分析，反复迭代直到结构重量收敛. 算例表明程序的合理性和有效性，能够满足工程设计的需要.     

带孔隙损伤的弹性固体的广义变分原理

应用弹性微结构理论,建立了具广义力场带孔隙损伤线弹性固体的基本模型．应用变积方法,同时分别建立了带孔隙损伤弹性固体四类和两类变量的广义变分原理,这些变分原理对应着带孔隙损伤弹性固体微分方程和初值边值条件．应用弹性微结构理论,建立了带孔隙损伤的弹性Timoshenko 梁的基本方程,得到带孔隙损伤的弹性Timoshenko 梁两类变量的广义变分原理．这些广义变分原理为近似求解带孔隙损伤的弹性问题提供了有效途径．     

Computation of cascade flutter by uncoupled and coupled methods

A computational method for flutter prediction of turbomachinery cascades is presented. The flow through multiple blade passages is calculated using a time-domain approach with coupled aerodynamic and structural models. The unsteady Euler/Navier-Stokes equations are solved in quasi-three-dimensions using a second-order implicit scheme with dual time-stepping and a multigrid method. A structural model for the blades with bending and torsion degrees of freedom is integrated in time together with the flow field. Information between structural and aerodynamic models is exchanged until convergence in each real-time step. Computational results for a cascade are presented and compared with those obtained by the conventional energy method and with experimental and numerical data by other authors. Significant differences are found between the coupled and uncoupled methods at low mass ratios. A transonic test case with strong nonlinear phenomena is investigated with the fluid-structure coupled method. Results for inviscid flow are compared with results of Navier-Stokes computations.     

A model for rolling deformation with grain subdivision. Part II: The subsequent stage

Part I of the present work dealt with the initial stage of plastic deformation with grain subdivision into two band families. It covered the situation with different average strains in the individual grains (the non-Taylor case) and the situation with identical average strains in the individual grains (the Taylor case). For the latter situation part I included solutions with 5 plus 3 and with 4 plus 4 active slip systems in the two band families, respectively. In part II we deal with the subsequent stage of plastic deformation (finite strains) for the Taylor case with four active slip systems in each band family. In the subsequent stage the cooperation between the two band families leads to an energetic advantage for grain subdivision, and it leads to a simulated texture with decreased sharpness in accordance with experimental observations. Finally, the physics behind grain subdivision are discussed on the basis of the results in Parts I and II and various general considerations.     

无限粘弹性平面中孔洞扩展的时变力学解析解

从粘弹性时变力学基本方程出发,针对Maxwell本构模型,导出了双向等压下粘弹性平面中圆孔半径任意规律扩展时的时变力学解析解.在内径线性时变时,其结果与用对应原理法得出的解相同,其解的可靠性得到验证.与对应原理法相比,文中的结果适用于半径任意时变情况,更具一般性.     

Effects of injection timing on performance and droplet characteristics of a sixteen-valve four cylinder engine

 The performance and droplet characteristics of a sixteen-valve, four cylinder engine operating with combustion in one cylinder have been measured with part load, a speed of 1200 rpm and a stoichiometric mixture of gasoline and air. The indicated mean-effective cylinder pressure was found to be constant with initiation of injection from 150° to 630° of crank angle after top-dead-centre of intake and with a 10% reduction between 30° and 60° which coincided with maxima in the covariance in pressure and in the emissions of unburned hydrocarbon. There was also a tendency for performance to decline with injection after 660°. Measurements with laser- and phase-Doppler velocimeters showed that the number of droplets entering the cylinder was much reduced with injection at crank angles corresponding to closed inlet valves due to evaporation, and that the few large droplets which emerged did not survive until top-dead-centre of compression. In contrast, some of the many droplets associated with injection with the valves open survived to the crank angle of ignition and it is likely that these led to an inhomogeneous charge with poorer flame-front propagation responsible for reduction in performance. Received: 19 February 1996/Accepted: 8 October 1996     

屈服准则及切线模量修正的弹塑性计算模型

为提高不同应力状态下金属弹塑性行为的模拟精度,采用含应力三轴度修正的von Mises屈服准则,材料弹塑性本构关系在等效应力$\!$-$\!$-$\!$等效应变曲线基础上,提出一个切线模量为主应力函数的理论修正项. 将这两个修正项结合,以子程序形式编程嵌入ABAQUS主程序,以此模拟几种不同形状试样的弹塑性行为,并将其他屈服准则在单一曲线假设下编程与之对比. 模拟结果与真实试验结果对比发现,对于屈服而言,含应力三轴度修正的vonMises屈服准则比其他屈服理论准确;对于弹塑性阶段计算而言,提出的切线模量为主应力函数这一假设比单一曲线假设更加接近真实试验.      

一种新的墙单元

本文提出了一种新的空间墙单元模型，这种墙单元把土建中常用的剪力墙作为它的一种特殊情形．本文基于四边形单元所提出的墙单元在平面内是一块膜，它除面内的两个平动自由度外还具有绕平面转动的自由度；平面外是一块弯曲板．因而它是膜和板的一个组合，它的每个节点具有空间的全部六个自由度．由于考虑了空间墙平面内和平面外的刚度，因此这种新的墙单元能够直接与三维框架的梁、柱单元连接．它也能很容易地处理墙的空间变形。     

Coupled RANS–LPT modelling of dilute,particle-laden flow in a duct with a 90° bend

A dilute, particle-laden flow in a square duct with a 90° bend is modelled using a RANS approach, coupled to a second-moment turbulence closure, together with a Lagrangian particle tracking technique, with particle dispersion modelled using a stochastic approach that ensures turbulence anisotropy. Detailed predictions of mean and fluctuating fluid and particle velocities are validated through comparisons of predictions with experimental measurements made for gas–solid flows in a vertical-to-horizontal flow configuration. Reasonable agreement between predicted first and second moments and data is found for both phases, with the consistent application of anisotropic and three-dimensional modelling approaches resulting in predictions that compare favourably with those of other authors, and which provide fluctuating particle velocities in acceptable agreement with data.     

横向三维化学反应流动数值模拟

对一个三维化学反应流程序作了改进,使之适应于模拟带横向碘蒸汽注入的COIL(化学氧碘激光)喷管流动。其中,主副气流的入流边界条件的改进是基本的,重要的。这里,入流边界附近的气体流动被视为一维均熵流动,用双曲方程的特征理论,分析以流量作变量的EULER方程的特征关系,用特征方法数值求解简化的特征方程,从而确定亚声速(跨声速)流动边界点的入流密度或速度。对相关文献提供的算例的计算,佐证了程序改进的有效性。对氮气作载气的条件也作了模拟,得出了与氦气条件不同的流动特征与增益分布特征。     

扭转预应变对35CrMo钢低周疲劳性能的影响

自行设计了疲劳和扭转两用的试样,通过对试件预扭转不同的角度,系统研究35CrMo钢在不同扭转预应变下的低周疲劳性能,分析了扭转预应变后35CrMo钢的循环硬化软化特性、滞后回线、塑性应变能及循环弹性模量的变化规律,并对疲劳断口进行扫描电镜分析。结果表明:4种预扭转处理过的试件均表现出明显的循环软化行为,且循环软化规律及衰减的程度基本相同;循环应力范围及疲劳寿命随着预扭转角的增大而降低;应力应变滞后回线中加卸载曲线间的宽度随着预扭转角的增大而减小;塑性应变能都随着循环次数的增大而增加,且随着预扭转角的增大其增大速率下降;循环弹性模量都随着循环次数的增加而逐渐降低,且随着预扭转角的增大其衰减趋势减缓。     

A further work on directed rods

In this paper, we discuss the field equations of a rod with three deformable directors. We then deal with the rod subjected to internal constraints. Finally, we compare the theory of the constrained directed rod with that of an unconstrained rod with two deformable directors and with that of Cosserat rods.     

正常固结饱和黏性土三剪有限变形弹塑性本构模型研究

基于三剪统一强度准则,利用等量代换法和坐标平移法分别推导出正常固结饱和黏性土的三剪破坏应力比,并将其与修正剑桥模型相结合,得到三剪统一屈服面方程。为反映饱和黏性土的变形非线性及大变形特性,基于有限变形理论,建立了正常固结饱和黏性土的三剪统一有限变形等量代换法和坐标平移法2种弹塑性本构模型。为验证模型的适用性,取江西红黏土制备三种不同压实度的试样,在不同围压下进行常规三轴固结不排水和固结排水压缩试验。将试验数据与本文所提2种有限变形模型及相应的2种小变形模型计算结果进行了对比分析,结果表明,随着变形的发展,有限变形模型相对于小变形模型更接近试验结果,能较好地反映黏性土因高孔隙率（低初始压实度、小围压及压缩变形前期）而产生的大变形特性,虽然小变形模型的计算偏差会随着土样初始压实度和所施加围压的增大而减小,但有限变形模型对不同压实度和围压的计算偏差均相对较小,其中,等量代换法有限变形模型在初始压实度较大或者围压较高时所得计算偏差相对最小。对所提本构模型所做真三轴分析表明,中间主应力影响系数b和初始压实度对土体的强度和变形特性具有一定的影响。主应力差、孔隙水压力和体应变与b值呈正相关性,主应力差与初始压实度呈正相关性,孔隙水压力和体应变与初始压实度呈负相关性。     

智能结构密频系统振动控制及其摄动分析

提出一种智能结构密频控制规律的设计方法。其主要工作为：将密频子空间转化为重频子空间,把密频系统作为重频系统上的摄动;为了解决重频密频子空间相对应的特征向量选取的敏感性问题,通过摄动分析得到与重频密频子空间相对应特征向量的线性组合并利用闭环系统特征值极点配置的方法得到重频密频系统的振动规律;把所设计的振动控制规律作用于原系统和摄动系统上,讨论了结构参数改变后对系统的动态特性的影响;最后通过算例证明该方法的有效性。     

Characterization of Irradiation Damage of Ferritic ODS Alloys with Advanced Micro-Sample Methods

Oxide dispersion strengthened (ODS) steels are candidate materials for advanced electric energy and heat generation plants (nuclear, fossil). Understanding the degradation of mechanical properties of these alloys as a result of service exposure is necessary for safe design. For advanced nuclear applications combinations of temperature, irradiation and stress are important damage conditions. They are studied either with neutron irradiated samples (often highly active) or with ion-irradiated samples (irradiation damage often limited to only a few micrometer deep areas). High activity of samples and limited sample volume claim to subsized samples like nano-indentation, micro-pillar compression or thin strip creep testing. Irradiation hardening and irradiation creep were studied with these methods. Ferritic ODS steels with 19% chromium were investigated. The materials were studied in qualities differing in grain sizes and in sizes of the dispersoids. Irradiation was performed in an accelerator using He-ions. Irradiation damage profiles could be well analyzed with indentation. Yield stress determined with compression tests of single-crystal micropillars was well comparable with tension tests performed along the same crystallographic orientation. Irradiation creep of samples with different sizes of dispersoids revealed only a small influence of particle size being is in contrast with thermal creep but consistent with expectations from other investigations.