水泥粉煤灰加固有机质土的试验研究

对于高有机质含量的泻湖相软土,单纯采用水泥不能有效提高该软土的力学性能,因此提出了采用水泥和粉煤灰作为固化剂的加固方法。通过不同水泥掺入量、粉煤灰掺入量和龄期下水泥土的无侧限抗压强度试验,分析了水泥粉煤灰固化土的强度规律和变形规律,探讨了水泥和粉煤灰加固高有机质含量软土的机理。结果表明,粉煤灰对于水泥试块的早期强度影响较小,对后期强度影响较大;粉煤灰最佳掺入量为12％,超过此掺入量水泥土强度反而会降低,粉煤灰水泥土的破坏应变、E50也在粉煤灰掺量为12％时分别达到最低值和最大值。水泥掺加粉煤灰可有效地提高高有机质含量软土的强度。     

改良黄土强度特性与工程处置试验研究

本文针对山西朔州典型黄土,利用素黄土与石灰粉煤灰、石灰水泥、水泥粉煤灰三种改良黄土,进行了击实特性、抗剪强度特性及崩解特性试验研究,提出了黄土改良的最佳方案,并采用该方案对山西某煤矿电梯井填方段进行了数值模拟分析,验证了石灰粉煤灰改良黄土工程应用的可行性。试验结果表明:粉煤灰与黄土形成致密的混合结构,石灰的掺入,激活了粉煤灰的活性,发生了一系列的水化反应,使改良黄土的强度大大提高,改良黄土在物理力学性质方面有明显改善。     

粉煤灰及SAP对喷射混凝土早龄期开裂损伤影响

为系统研究粉煤灰、吸水保水剂(SAP)对喷射混凝土早龄期开裂损伤的影响,以掺入了粉煤灰、SAP的喷射混凝土为研究对象,对喷射混凝土的早龄期开裂损伤进行平板法试验研究。完成了各种试件的早龄期开裂损伤测试,研究了粉煤灰对喷射混凝土以及SAP对掺入20%粉煤灰喷射混凝土的早龄期开裂损伤的改善作用。试验结果表明,掺粉煤灰等量取代10%、20%水泥后,喷射混凝土的早龄期开裂损伤与基准喷射混凝土相比分别减小约7.2%和26.8%。掺0.25%SAP和0.5%SAP可以使20%粉煤灰掺量喷射混凝土的早龄期开裂损伤与基准喷射混凝土相比分别减小约57.9%和66.50%。因此,掺粉煤灰可有效地降低喷射混凝土早龄期开裂损伤,且在掺加粉煤灰的基础上再掺加适量的SAP效果会更佳。     

淮河大堤老应段土体蠕变特性研究及工程应用

本文依据工程需要, 采取淮河大堤老应段的原状和扰动土样, 在室内对堤体及堤基土的剪切蠕变和拉伸蠕变特性进行了试验研究。粘土的蠕变剪切强度远低于瞬时剪切强度, Ｃ∞值仅是Ｃ值的４０％左右;相同含水条件下粘土的长时抗拉强度大于瞬时抗拉强度, 长时拉伸应变量远大于瞬时拉伸应变量, 约为２倍。     

广西靖西红粘土的变形和强度特性研究

对广西靖西取得的3种红粘土原状土样以及室内制备的重塑土样进行单轴压缩试验和三轴剪切试验（包括浸水饱和后的试验）,其目的是研究静力荷载作用下红粘土的固结变形和强度特征。研究表明,在较大的压缩应力作用下,土样仍有较大的孔隙比;红粘土的破坏面为一个曲面变化形态,试样首先沿较为软弱的不规则面发生,然后才形成贯通的滑动面;尽管土样在破坏时出现明显的剪切破坏面（表现为一定的脆性破坏特征）,但其应力应变关系呈现应变硬化的特点,表明红粘土有很强的粘滞特性。     

真空排水预压下土体变形的应力路径分析

通过室内试验, 对真空排水预压下土体变形特性进行了应力路径分析, 测定软土地基在真空预压加固后应力路径的改变对沉降量的影响, 论证真空排水预压加固软土地基不能消除其剪应力引起的剪切变形, 结合实例, 计算其后期沉降量与固结沉降量的比值, 并推算软土地基在真空预压下其最终沉降量计算公式的修正系数。     

粉质粘土结构性参数试验研究

为合理描述外部环境改变引起土体结构性的变化规律,基于综合结构势理论,通过三轴剪切试验,研究了应力比结构性参数(mη)随试验条件的变化规律。试验结果表明:粉质粘土应力-应变曲线包括应变软化型曲线、理想弹塑性曲线、应变硬化型曲线3种形式;粉质粘土强度随着含水量的增大而减小,随着围压的增大而增大。粉质粘土应力比结构性参数随着含水率和围压的增大而减小。采用初始应力比结构性参数和结构性损伤量参数两个参数,建立了粉质粘土结构性应力-应变数学模型。将试验结果与模型计算结果进行了对比分析,结果表明二者强度误差小于3%,说明了所建立模型的合理性。     

二维有限区域饱和软土Biot固结的数值模拟

针对二维有限矩形区域饱和软土固结问题,选取四种不同边界条件组合,利用数值模拟方法研究了在上表面剪切载荷作用下土体沉降变形的特征和规律。结果表明:在剪切载荷单独作用下,土体位移以水平位移为主,同时竖向位移也客观存在。这反映了土体固结过程中流固耦合的物理现象。土层最终变形量(沉降和水平位移)由剪切载荷与土体物性决定,与边界透水性无关;边界条件对土体的变形模式有着决定性影响。剪切载荷作用、法向载荷作用及二者联合作用的计算结果对比表明:虽然软土Biot固结是复杂的流固耦合过程,但在这个过程中载荷叠加原理依然成立。     

基于邓肯-张的冻结粉质粘土本构模型试验研究

为研究冻结粉质粘土强度和变形特性,以沈阳地铁DK11+395联络通道处人工冻结粉质粘土为研究对象,通过冻土三轴剪切试验,研究了不同试验条件下冻结粉质粘土的强度和变形特性。试验结果表明：围压、温度和试件初始含水量是影响冻结粉质粘土强度和变形的主要因素。冻结粉质粘土偏应力-应变曲线呈应变硬化型,其破坏强度和切线弹性模量随围压和试件初始含水量的增加而增大,随温度的升高而减小,破坏偏应力比Rf取值在0.79~0.96之间。基于试验数据建立了以上述三因素为影响因子的冻结粉质粘土Duncan-Chang模型。通过回归分析,建立了模型参数a和b与围压、初始含水量和温度之间的线性回归公式。将依据模型计算的偏应力-应变曲线与对比试验曲线相比较,发现两者具有较好的吻合程度,说明建立的模型能够准确反映围压、初始含水量和温度等条件对冻结粉质粘土强度和变形的影响规律。上述研究成果为冻结粉质粘土强度和变形特性的研究提供了参考,为人工冻结法施工提供了指导,具有重要的理论意义和工程应用价值。     

用内蕴时间理论进行粘土流变性研究

利用内蕴时间理论对粘土的流变性进行了理论研究,提出了在假三轴条件下粘土的流变本构方程,并且利用粘土的流变试验对所得粘土流变本构方程进行了验证,结果表明用内蕴温度理论推导的粘土流变本构方程能准确地描述粘土的流变性。     

主应力轴旋转对压实黄土动变形特性的影响

实际工程中的地基或路基的土体往往处于复杂初始应力状态,在地震或其他动荷载的作用下会出现变形和沉降,而常规的室内土工试验无法真实再现这种固结应力条件下土的动力特性。通过对原有的DTC 199型周期扭转荷载三轴仪进行简单的改造后可进行土体在主应力轴发生旋转时的压实黄土动变形的试验研究。结果表明,在其他固结条件不变的情况下,初始主应力方向角α对压实黄土的动剪切模量有一定的影响,随着α的增加,动剪切模量有减小的趋势,最大动剪应力也逐渐减小,但是α对最大动剪切模量的影响不太显著。初始主应力方向角α对压实黄土的阻尼比基本没有影响,在λ-lgγd的半对数坐标图中,阻尼比随动剪应变的增加有逐渐增大的趋势,并且表现出较好的相关性。     

On the simple and mixed first-order theories for functionally graded plates resting on elastic foundations

In this article, the bending response of a functionally graded plate resting on elastic foundations and subjected to a transverse mechanical load is investigated. An accurate solution for the functionally graded plate with simply supported edges resting on elastic foundations is presented. The interaction between the plate and the elastic foundations is considered and included in the equilibrium equations. Pasternak’s model is used to describe the two-parameter elastic foundations, and get a special case of Winkler’s model by considering one-parameter of elastic foundation. A relationship between the simple and mixed first-order transverse shear deformation theories is presented. Numerical results for deflections and stresses of functionally graded plates are investigated. Comparisons between the results of the simple and mixed first-order theories are made, and appropriate conclusion is formulated. Additional boundary conditions at the edges of the present plates are investigated.     

冻融循环作用下再生混凝土砖砌体通缝受剪试验研究

本文报导了对冻融循环作用下96个再生混凝土砖砌体抗剪试件进行的沿通缝抗剪试验。研究涉及冻融循环对再生混凝土砖砌体抗剪力学性能的影响,对比分析不同胶结材料试件的破坏形态及其抗剪强度,揭示冻融损伤对再生混凝土砖砌体抗剪强度的影响规律,并从微观角度探讨砂浆孔隙变化对砖砌体抗剪承载力的影响,建立再生混凝土砖砌体抗剪强度冻融损伤衰减模型。结果表明:砖砌体抗剪强度受冻融环境影响非常明显,其抗剪强度随冻融循环次数的增加而降低,降低的速度呈现出先慢后快的趋势;粉煤灰的加入有助于改善冻融环境下砖砌体的抗剪能力;对于石灰砂浆抗剪试件,初期的抗剪能力及冻融后的抗剪能力均下降;建立了考虑冻融损伤影响的砖砌体抗剪强度衰减模型,试验数据与计算结果吻合较好。     

Relation between silico-aluminous fly ash and its coal of origin

Fly ashes are typical complex solids which incorporate at the same time intrinsic properties derived from the layers (various mineralogical and dimensional spectra) and major transformations generated during prior processing. To use fly ashes in various applications, it is necessary to characterise them completely. The first research to date carried out on silico-aluminous fly ashes in order to characterise them physically,morphologically, chemically and mineralogically, resulted in the recognition that they are relatively simple materials. In the present study, a silico-aluminous fly ash coming from the power station of Albi (France) was selected. Heat treatment at 450 and 1200 ~C together with coal simulated the treatment undergone by coal in the power station in order to mimic real coal residue. In conclusion, the diversity of the particles contained in fly ash could only be explained by the relation existing between the fly ash and its coal of origin.     

The flow behavior of powder stearin-based methyl ester sulfonates and the effect of glidant

The preparation and behavior of powder stearin-based methyl ester sulfonates (MES) with the addition of builder as a glidant agent was studied. MES is an anionic surfactant and its performance is equivalent to petroleum-based linear alkylbenzene sulfonates (LAS), the workhorses of the detergent industry. At the same time, zeolites or soda ash were the alternative builders for non-phosphate-based detergent. The behavior of powder MES properties was measured in terms of morphology, particle size, cohesion, caking, and compaction. Before that, these palm stearin-based MES of carbon chain 16–18 with ratios of 98:2, 80:20, and 60:40 in flakes were ground using a high shear mixer by 23,000 rpm to produce powder particles. Decreasing the particle size of MES powder can reduce the powder's cohesion, caking, and compaction. The addition of zeolite or soda ash as a glidant in powdered MES can improve the caking behavior. The high stearic in MES greatly influenced getting fine particle powders and required more glidant agents. This powder MES with excellent powder characteristics can perform well as a bio-based cleaning product.     

Relation between silico-aluminous fly ash and its coal of origin

Fly ashes are typical complex solids which incorporate at the same time intrinsic properties derived from the layers （various mineralogical and dimensional spectra） and major transformations generated during prior processing. To use fly ashes in various applications, it is necessary to characterise them completely. The first research to date carried out on silico-aluminous fly ashes in order to characterise them physically, morphologically, chemically and mineralogically, resulted in the recognition that they are relatively simple materials. In the present study, a silico-aluminous fly ash coming from the power station of Albi （France） was selected. Heat treatment at 450 and 1200℃ together with coal simulated the treatment undergone by coal in the power station in order to mimic real coal residue. In conclusion, the diversity of the particles contained in fly ash could only be exolained by the relation existing between the fly ash and its coal of origin.     

Removal of inhalable particles from coal and refuse combustion by agglomeration with solid nuclei

Airborne inhalable particles are a potent environmental pollutant. Formed via industrial processes, separation of these particles is difficult using conventional clean up techniques. In this work, solid nuclei particles of different chemical compositions were introduced into an agglomeration chamber with simulated flue gases to investigate their ability to remove these particles. Organic nuclei were able to capture more inhalable particles from coal-derived fly ash than inorganic nuclei, though these proved more effective for the agglomeration of inhalable particles in refuse-derived fly ash. Increasing the diameter of the solid nuclei benefitted the agglomeration process for both types of ash. Varying the local humidity changed adhesion between the particles and encouraged them to aggregate. Increasing the relative humidity consistently increased particle agglomeration for the refuse-derived ash. For coal-derived fly ash, the removal efficiency increased initially with relative humidity but then further increases in humidity had no impact on the relatively high efficiencies. After agglomeration in an atmosphere of 62% relative humidity, the mean mass diameter of inhalable particles in the coal-derived fly ash increased from 3.3 to 9.2 μm. For refuse-derived fly ash, agglomeration caused the percentage of particles that were less than 2 μm to decrease from 40% to 15%. After treatment at a relative humidity of 61%, the mean size of inhalable particles exceeded 10 μm.     

辽西风积土动应力试验研究

通过对辽西地区风积土动三轴试验, 研究了动荷载作用下辽西风积土的动强度特性和抗液化特性.通过控制不同的动荷幅值、固结比和固结围压等试验条件, 获得了抗震设防烈度为7 度时, 辽西风积土的动应力值和抗液化剪应力比. 利用Excel 软件, 对试验数据进行回归处理, 得到了该土试样的动应力与固结比和固结围压两种因素的经验关系式. 试验和回归分析结果表明, 风积土的动应力与固结比和固结围压成正比. 试验研究了不同固结比条件下辽西地区风积土的液化强度特性, 获得了不同固结比条件下的抗液化剪应力比. 试验结果表明, 风积土的抗液化剪应力随着固结比的增加而增大. 上述试验结果对于辽西地区工程的抗震设计具有重要的指导意义和工程实用价值.