Visualization of a confined accelerated bubble

High-speed photography was used to study the collapse of a confined two-dimensional, air cavity in water, subjected to a propagating pressure disturbance. The 5–6 mm diameter cavity was confined in a rectangular duct. A sustained pressure disturbance was created by an accelerating piston in contact with the water 240 mm away from the bubble. The pressure increased from 0.1 MPa to about 0.12 MPa with a rise time of the order of 2 ms. The pressure pulse was not reflected until its arrival at the end of the duct, 320 mm from the piston. A microjet was produced at the proximal wall which penetrated the distal cavity wall, thereby producing a pair of bubbles which was thought to be regions of intense vorticity. The features of such confined bubble collapse were not found in previous investigations of unconfined bubble accelerations by weak pressure disturbances. Confinement apparently intensified the effect of the disturbance significantly. Received 18 August 1998 / Accepted 12 May 1999     

多障碍物通道中激波诱导气相爆轰的数值研究

应用数值模拟方法，研究了直通道中激波经过多块矩形障碍物时诱导 H2/O2混合气体起爆的物理机制. 研究表明：在前导激波强度不足以诱导波后气 体直接起爆的条件下，经过激波压缩的可燃气体也可能在远离激波的障碍物之间的凹槽部位 起爆；障碍物表面产生的压缩波、膨胀波和气流滑移面对可燃气体的起爆、爆轰波的形成和 传播过程有重要的影响；添加不同稀释比的氮气可以影响爆轰波后流场的温度分布；增加障 碍物的间距可以改变可燃气起爆位置.     

On flows behind shock waves reflected from a solid wall

The flow fields associated with the interaction of a normal shock wave with a plane wall kept at a constant temperature were studied based on kinetic theory which can describe appropriately the shock structure and its reflection process. With the use of a difference scheme, the time developments of the distributions of the fluid dynamic quantities (velocity, temperature, pressure and number density of the gas) were obtained numerically from the BGK model of the Boltzmann equation subject to the condition of diffusive-reflection at the wall for several cases of incident Mach number:M ₁=1.2, 1.5, 2.0, 3.0, 4.0, 5.0 and 6.0. The reflection process of the shocks is shown explicitly together with the resulting formation of the flow fields as time goes on. The nonzero uniform velocity toward the wall occurring between the viscous boundary layer and the reflected shock wave is found to be fairly large, the magnitude of which is of the order of several percent of the velocity induced behind the incident shock, decreasing as the incident Mach number increases. It is also seen that a region of positive velocity (away from the wall) within the viscous boundary layer manifests itself in the immediate vicinity of the wall, which is distinct for larger incident Mach numbers. Some of the calculated density profiles are compared with available experimental data and also with numerical results based on the Navier-Stokes equations. The agreement between the three results is fairly good except in the region close to the wall, where the difference in the conditions of these studies and the inappropriateness of the Navier-Stokes equations manifest themselves greatly in the gas behavior.This article was processed using Springer-Verlag TEX Shock Waves macro package 1990.     

反射激波冲击重气柱的RM不稳定性数值研究

数值研究了二维气柱在入射激波以及反射激波作用下的Richtmyer-Meshkov(RM)不稳定性发展规律, 采用有限体积法结合网格自 适应技术的VAS2D程序, 精确刻画激波和界面的演化. 入射平面激波的马赫数为1.2, 气柱界面内气体为六氟化硫(SF₆), 环境气体为空气, 激波管的尾端为固壁. 通过改变气柱与尾端之间的距离调节反射激波再次作用已经变形的气柱的时间, 获得不同时刻下已经变形的气柱形态、界面尺寸以及环量演化受到反射激波的影响. 结果表明, 反射激波再次作用气柱时, 气柱所处发展阶段不同, 界面演化规律以及环量随时间的变化也不相同, 反射激波与气柱相互作用过程中的涡量产生和分布与无反射情况差异较大, 揭示了不同情况下界面演化的物理机理.     

Interaction of a reflected shock from a concave wall with a flame distorted by an incident shock

Observations are presented from calculations where a laminar spherical CH₄/air flame was perturbed successively by incident and reflected shock waves reflected from a planar or concave wall. The two-dimensional axi-symmetric Navier–Stokes equations with detailed chemistry were used. The computational results were qualitatively validated with experiments which were performed in a standard shock tube arrangement. Under the influence of the incident shock wave, a Richtmyer–Meshkov instability is induced in the flame, and the distorted flame finally takes the form of two separated elliptical burning bubbles in the symmetric cross plane. Then, under subsequent interactions with the shock wave reflected from the planar or the concave wall, the flame takes a mushroom-like shape. Transverse waves produced by the shock reflection from the concave wall can compress the flame towards the axis, and the focusing shock generated on the concave wall will lead to a larger mushroom-like flame than that induced by the planar reflection.      

Experimental study of planar shock wave interactions with dense packed sand wall

A dense packed sand wall is impacted by a planar shock wave in a horizontal shock tube to study the shock-sand wall interaction. The incident shock Mach number ranges from 2.18 to 2.38. A novel device for actively rupturing diaphragm is designed for the driver section of the shock tube. An apparatus for loading particles is machined by the electrical discharge cutting technique to create a dense packed particle wall. High-speed schlieren imaging system and synchronized pressure measurement system are used together to capture the wave structures and particle cloud velocity. The dynamic evolution model from dense packed particles to dense gas–solid cloud at the initial driving stage is established. The blockage and permeation effects of the sand wall work together and influence each other. The high pressure gas behind the incident shock wave blocked by the sand wall pushes the upstream front of the wall forward like a piston. Meanwhile, the high speed gas permeating through the sand wall drags the sands of the most downstream layer forward. The incident shock strength, initial sand wall thickness and particle diameter are varied respectively to investigate the shock attenuation and the wall acceleration. Increasing the sands diameter or mixing in small diameter sands can significantly attenuate the incident shock. The smaller particles or the particles in thinner wall can be dispersed into a larger range in the process of transform from dense packed particles to dense gas–solid cloud. Moreover, the stronger incident shock can disperse the particles into a larger region.     

Overpressure generation and repetition of collapsing microbubbles induced by shock wave reflection in a narrow gap

This paper reports the summary of experiments performed to successive generate small-scale underwater shock waves by means of shock-induced collapse of microbubbles confined in a narrow gap. The project is motivated to develop a method for efficient inactivation of marine bacteria contained in ship ballast water by high impulsive pressure loading. The shock wave–air bubbles interaction was visualized by shadowgraph; the images were recorded by ImaCon200, and simultaneous pressure measurements were performed by using an optical fiber pressure transducer with higher temporal resolution. Attaching small air bubbles on a single nylon fiber and placing it in a confined space, we demonstrated sequential generation of impulsive high pressures at the successive collapses of small bubbles at incident and reflected shock loadings. The values of the very short impulsive pressures that occurred repeatedly for a relatively long term are found high enough to inactivate marine bacteria.     

Formation and evolution of vortex rings induced by interactions between shock waves and a low-density bubble

The deformation and instability of a low-density spherical bubble induced by an incident and its reflected shock waves are studied by using the large eddy simulation method. The computational model is firstly validated by experimental results from the literature and is further used to examine the effect of incident shock wave strength on the formations and three-dimensional evolutions of the vortex rings. For the weak shock wave case (Ma?=?1.24), the baroclinic effect induced by the reflected shock wave is the key mechanism for the formation of new vortex rings. The vortex rings not only move due to the self-induced effect and the flow field velocity, but also generate azimuthal instability due to the pressure disturbance. For the strong shock wave case (Ma?=?2.2), a boundary layer is formed adjacent to the end wall owing to the approach of vortex ring, and unsteady separation of the boundary layer near the wall results in the ejection and formation of new vortex rings. These vortex rings interact in the vicinity of the end wall and finally collapse to a complicated vortex structure via azimuthal instability. For both shock wave strength cases, the evolutions of vortex rings due to the instability lead to the formation of the complicated structure dominated by the small-scale streamwise vortices.     

A volume-fraction based algorithm for hybrid barotropic and non-barotropic two-fluid flow problems

The aim of this paper is to describe a simple Eulerian interface-capturing approach for the efficient numerical resolution of a hybrid barotropic and non-barotropic two-fluid flow problem in more than one space dimension. We use the compressible Euler equations as a model system with the thermodynamic property of each of the barotropic and non-barotropic fluid components characterized by the Tait and Noble–Abel equations of state, respectively. The algorithm is based on a volume fraction formulation of the equations together with an extended equation of state that is devised to give an approximate treatment for the mixture of more than one fluid component within a grid cell. A standard high-resolution wave propagation method is employed to solve the proposed two-fluid model with the dimensional-splitting technique incorporated in the method for multidimensional problems. Several numerical results are presented in one and two space dimensions that show the feasibility of the algorithm as applied to a reasonable class of practical problems without the occurrence of any spurious oscillation in the pressure near the smeared material interfaces. This includes, in particular, solutions for a study on the variation of the jet velocity with the incident shock pressure arising from the collapse of an air cavity in water under a shock wave.     

可燃气体中激波聚焦的点火特性

数值模拟了二维平面激波从抛物面上反射在可燃气体中聚焦的过程，研究了形 成爆轰波的点火特性. 对理想化学当量比氢气/空气混合气体，在初始压强20kPa的条件下， 马赫数2.6-2.8的激波聚焦能产生两个点火区：第1个点火区是反射激波会聚引起的，第 2个点火区是由入射激波在抛物面上发生马赫反射引起的. 这种条件下流场中会出现爆燃转 爆轰，起爆点分别分布在管道壁面、抛物反射面和第2点火区附近. 起爆机理分别为激波管 道壁面反射、点火诱导激波的抛物面反射和点火诱导的激波与第2点火区产生的爆燃波的相 互作用. 不同的点火和起爆过程导致了不同的流场波系结构，同时影响了爆轰波传播的波动 力学过程.     

Near-wall imaging using toluene-based planar laser-induced fluorescence in shock tube flow

A quantitative thermometry technique, based on planar laser-induced fluorescence (PLIF), was applied to image temperature fields immediately next to walls in shock tube flows. Two types of near-wall flows were considered: the side wall thermal boundary layer behind an incident shock wave, and the end wall thermal layer behind a reflected shock wave. These thin layers are imaged with high spatial resolution (15μm/pixel) in conjunction with fused silica walls and near-UV bandpass filters to accurately measure fluorescence signal levels with minimal interferences from scatter and reflection at the wall surface. Nitrogen, hydrogen or argon gas were premixed with 1–12% toluene, the LIF tracer, and tested under various shock flow conditions. The measured pressures and temperatures ranged between 0.01 and 0.8 bar and 293 and 600 K, respectively. Temperature field measurements were found to be in good agreement with theoretical values calculated using 2-D laminar boundary layer and 1-D heat diffusion equations, respectively. In addition, PLIF images were taken at various time delays behind incident and reflected shock waves to observe the development of the side wall and end wall layers, respectively. The demonstrated diagnostic strategy can be used to accurately measure temperature to about 60 μm from the wall.     

用环形激波聚焦实现爆轰波直接起爆的数值模拟

利用基元反应模型和有限体积法对环形激波在可燃气体中聚焦实现爆轰波直接起爆进行了数值模拟。研究结果表明，标准状态下的氢气-空气混合气体在马赫数为3.1以上的环形激波聚焦产生的高温高压区作用下会诱发可燃气体的直接起爆形成爆轰波，爆轰波与激波和接触间断相互作用产生了复杂的波系结构；爆轰波爆点位置在对称轴上并不是固定的点，而是随着初始激波马赫数的变化而发生移动；可燃气体初始温度和压力对起爆临界马赫数都有影响，但是初始温度的影响大得多。     

空化可压缩流动空穴溃灭激波特性研究

为深入研究空化可压缩流动中空泡/空泡团溃灭过程中激波产生、传播及其与空穴相互作用规律,本文采用数值模拟方法对空化可压缩流动空穴溃灭激波特性展开了研究.数值计算基于OpenFOAM开源程序,综合考虑蒸汽相和液相的压缩性,通过在原无相变两相可压缩求解器的控制方程中耦合模拟空化汽液相间质量交换的源项,实现了对空化流动的非定常可压缩计算.利用上述考虑汽/液相可压缩性的空化流动求解器,对周期性云状空化流动进行了数值模拟,并重点研究了空穴溃灭激波特性.结果表明:上述数值计算方法可以准确捕捉到空穴非定常演化过程及大尺度脱落空泡云团溃灭激波现象,大尺度脱落空泡云团溃灭过程分为3个阶段:(1) U型空泡团形成; (2) U型空泡团头部溃灭; (3) U型空泡团腿部溃灭.在U 型空泡团腿部溃灭瞬间,观察到激波产生,并向上游和下游传播,向上游传播的激波与空穴相互作用,导致水翼吸力面新生的附着型片状空穴回缩,直至完全溃灭.并且空穴溃灭激波存在回弹现象, 抑制了下一周期的空化发展.      

Experiments on the Richtmyer–Meshkov instability with an imposed, random initial perturbation

A vertical shock tube is used to perform experiments on the Richtmyer–Meshkov instability with a three-dimensional random initial perturbation. A membraneless flat interface is formed by opposed gas flows in which the light and heavy gases enter the shock tube from the top and from the bottom of the shock tube driven section. An air/SF $_{6}$ gas combination is used and a Mach number $ M = 1.2$ incident shock wave impulsively accelerates the interface. Initial perturbations on the interface are created by vertically oscillating the gas column within the shock tube to produce Faraday waves on the interface resulting in a short wavelength, three-dimensional perturbation. Planar Mie scattering is used to visualize the flow in which light from a laser sheet is scattered by smoke seeded in the air, and image sequences are captured using three high-speed video cameras. Measurements of the integral penetration depth prior to reshock show two growth behaviors, both having power law growth with growth exponents in the range found in previous experiments and simulations. Following reshock, all experiments show very consistent linear growth with a growth rate in good agreement with those found in previous studies.     

Dynamics of a bubble in a liquid under laser pulse action

Simulation was performed of the behavior of a vapor bubble in a liquid under laser irradiation in laboratory experiments. A mathematical model was developed to analyze the effect of heat conduction, diffusion, and mass transfer on the bubble dynamics under compression and expansion. It is found that at the stage of collapse, intense condensation occurs on the bubble wall, which results in a significant (more than 15fold) decrease in bubble mass and an increase in pressure (to 10⁵ atm) and temperature (to 10⁴ K(. Results of numerical calculations of the radius of the first rebound and the amplitude of the divergent shock wave in water are compared with experimental data. It is shown that small (:about 1%) additives of an incondensable gas lead to a considerable decrease in mass transfer on the bubble wall.     

Attenuation of weak shock waves along pseudo-perforated walls

In order to attenuate weak shock waves in ducts, effects of pseudo-perforated walls were investigated. Pseudo-perforated walls are defined as wall perforations having a closed cavity behind it. Shock wave diffraction and reflection created by these perforations were visualized in a shock tube by using holographic interferometer, and also by numerical simulation. Along the pseudo-perforated wall, an incident shock wave attenuates and eventually turns into a sound wave. Due to complex interactions of the incident shock wave with the perforations, the overpressure behind it becomes non-uniform and its peak value can locally exceed that behind the undisturbed incident shock wave. However, its pressure gradient monotonically decreases with the shock wave propagation. Effects of these pseudo-perforated walls on the attenuation of weak shock waves generated in high speed train tunnels were studied in a 1/250-scaled train tunnel simulator. It is concluded that in order to achieve a practically effective suppression of the tunnel sonic boom the length of the pseudo-perforation section should be sufficiently long. Received 23 June 1997 / Accepted 16 September 1997     

On the Mutual Penetrations of Two Fluids Whose Interface is Accelerated by a Shock Wave

A shock tube experimental investigation and numerical simulations are undertaken to study the evolution of a perturbed interface of two different gases accelerated by a shock wave. The experimental method is based on a high-speed camera laser sheet diagnostic technique, and simulations are provided by our code CARBUR based on a finite volume discretization of Navier–Stokes’s equations. Two gas pairs are used to illustrate both the heavy/light (air/He) and the light/ heavy (air/SF₆) cases. Two simultaneous large initial perturbations, one positive and one negative, are tested for an incident shock wave Mach number in air of about 1.3. The thin membrane (less than 1 μ) which materializes the initial interface between the two test gases presents 2D perturbations whose wave number is close to 1 in order to rapidly reach the non-linear regime. The development of the perturbations is captured at a frequency of 10 kHz after the interface acceleration, and the experiments are complemented with a numerical simulation to validate the interface deformations. Results show an asymmetric mutual gas penetration increasing with the absolute value of the Atwood’s number. Furthermore, they confirm that the heavier gas penetrates the lighter as thin spikes and the lighter gas penetrates the heavier as large bubbles. Moreover, we show that the spike moves faster than the bubble in the heavy/light case and slightly faster in the light/heavy one. Finally, numerical and experimental results are in agreement.     

The interaction of a shock wave with the boundary layer in a reflected shock tunnel

The influence of a nontotal reflection on the interaction of a reflected shock wave with the boundary layer in a reflected shock tunnel has been investigated. The calculating method of the velocity, the temperature and the Mach number profiles in the boundary layer in reflected shock fixed coordinates has been obtained. To account for equilibrium real gas effects of nitrogen, the numerical results show that the minimum Mach number in the boundary layer has been moved from the wall into the boundary layer with the increasing of the incident shock Mach number. The minimum Mach number, the shock angle in the bifurcated foot and the jet velocity along the wall to the end plate are reduced owing to the increasing of the area of nozzle throat. The numerical results are in good agreement with measurements.     

A numerical study of weak shock wave propagation in a reactive bubbly liquid

A numerical study is presented on the response of a weakly shock compressed liquid column that contains reactive gas bubbles. Both the liquid and gas are considered compressible. Compressibility of the liquid allows calculation of shock and rarefaction waves in the pure liquid as well as in the gas/liquid mixture. A microscopic model for local bubble collapse is coupled with a macroscopic model of wave propagation through the gas/liquid mixture. In the particular cases presented here, the characteristic times of propagation of the shock wave and bubble collapse are of the same order of magnitude. Consequently, the coupling between various phenomena is very strong. The present model based on fundamental principles of two-phase fluid mechanics takes into account the coupling of localized bubble oscillations. This model is composed of a microscopic one in the scale of a bubble size, and a macroscopic one which is based on the mixture theory. The liquid under study is water, and the gas is a reactive mixture of argon, hydrogen and oxygen. Received 18 December 1995 / Accepted 2 June 1996     

Shock-induced collapse of a vapor nanobubble near solid boundaries

The collapse of a nano-bubble near a solid wall is addressed here exploiting a phase field model recently used to describe the process in free space. Bubble collapse is triggered by a normal shock wave in the liquid. The dynamics is explored for different bubble wall normal distances and triggering shock intensities. Overall the dynamics is characterized by a sequence of collapses and rebounds of the pure vapor bubble accompanied by the emission of shock waves in the liquid. The shocks are reflected by the wall to impinge back on the re-expanding bubble. The presence of the wall and the impinging shock wave break the symmetry of the system, leading, for sufficiently strong intensity of the incoming shock wave, to the poration of the bubble and the formation of an annular structure and a liquid jet. Intense peaks of pressure and temperatures are found also at the wall, confirming that the strong localized loading combined with the jet impinging the wall is a potential source of substrate damage induced by the cavitation.