首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到18条相似文献,搜索用时 93 毫秒
1.
轴对称空泡流的脉动性态研究   总被引:3,自引:0,他引:3  
刘桦  何友声 《力学季刊》1997,18(2):99-105
本文采用高速摄影技术对定常来流中1/4平头轴对称体的不稳定的空泡形态特征进行了水洞试验研究。试验结果揭示了由于空泡形态断裂而产生的低频脉动现象,这一现象在跨空泡流情况下尤为明显,常使空泡长度和厚度在大幅范围内拟周期地变动,其频率特性比较稳定,有别于空泡末端局部泡团脱落而产生的脉动。  相似文献   

2.
空泡流非稳态现象的流动控制   总被引:3,自引:0,他引:3  
顾巍  何友声 《力学学报》2001,33(1):19-27
处于跨临界阶段的空泡流必然导致强烈的周期性冲击和振动,空泡流的激振来源于空泡云的周期性大规模脱落,空泡云的形成和发展与流动的边界层效应有着强烈的相关性,且空泡末端的局部流动直接影响空泡流的整体稳定性,本试验在NACA16012水翼表面粘附一条展向1mm厚10mm宽的挡流条,尝试以干扰水翼上表面局部流动的方法来影响整个空泡流的形态及其流动稳定性,最终在一定的空泡数范围内抑制了空泡流激振现象,并从试验研究的角度探索了空泡云脱落的机理。  相似文献   

3.
空化器参数对超空泡形成和发展的影响   总被引:3,自引:0,他引:3  
为了探索超空泡的生成机理和形态变化规律,依据其产生方式,进行了自然超 空泡高速射弹试验和通气超空泡水洞试验研究. 分析了超空泡的生成过程和空化器参数对形 成超空泡的临界空化数和通气系数门限值的影响. 研究了超空泡形态尺寸变化的特性,空化 器直径和线型对自然和通气超空泡的形态尺寸有相类似的影响规律:超空泡尺寸随着空化器 直径的增加而增加;在相同条件下,钝头空化器要比圆锥形空化器更容易形成超空泡;相对 较小的直径空化器很难形成透明的通气超空泡,其主要原因是自然空化数没有降到足够低. 此外,研究表明空化器直径对通气超空泡的细长比的影响较大,这与对自然超空泡形态的影 响不相同. 最后,对空化器的未来研究发展进行了展望.  相似文献   

4.
我们用激光多普勒技术(LDV)对钝头圆柱体、带小槽1.5度卵形头回转体、带背阶半球头回转体的绕流进行了测量。试验在600×600mm~2水洞中进行,雷诺数从0.75×10~5到6×10~5。给出了平均速度和脉动速度均方根值的分布并做了脉动速度的功率谱。得出了与过去热线流速计测量结果略有不同的结论。并且通过小槽内流动的测量对空泡的产生进行了分析。此外,本文提出一种捡测流动转捩现象的方法,用此法的实验结果与前人一致。  相似文献   

5.
湍流模型对空泡形态影响的数值研究   总被引:1,自引:0,他引:1  
为研究湍流模型对空泡尾部气体泄漏方式和空泡外形的影响,基于 FLUENT6.2的 VOF 多相流模型,对考虑重力作用下的三维通气空泡流进行了数值计算,比较了大涡模拟 LES 和 RNG k-ε两种湍流模型下的空泡形态和模型表面压力系数分布。结果显示,RNG k-ε模型计算的空泡内压力较大,空泡长度更长,而 LES 的瞬态计算结果更符合通气空泡的特性,相对而言更适用于通气空泡流的模拟。  相似文献   

6.
对4种不同头型的钝体、以不同初始速度在小倾斜角度和垂直状态下入水,所产生的空泡流进行了的实验观察,分析了不同工况下空泡产生和发展的特性。实验结果表明:对于倾斜入水及垂直入水,圆台头和平头(即空化器均为圆盘)实验体均能形成较稳定的入水弹道;初始入水速度较低时,空泡的闭合方式为深闭合;初始入水速度较高时,空泡的闭合方式为表面闭合,且运动速度衰减得更快。测量得知,钝体倾斜入水产生的空泡的前部外形轮廓与Logvinovich的半经验公式给出的结果相吻合。在垂直入水的情况下,调查了物体头部对空泡的起始点位置及其形态的影响。  相似文献   

7.
在脉动流条件下,用计算机数值模拟的方法对低密度脂蛋白(LDL)在动脉狭窄血管段内的质量传输进行了研究。计算结果表明.无论是在定常流还是在脉动流条件下.LDL都将聚积于血管狭窄处峰口附近的流动分离点,LDL壁面浓度在此处最高。在脉动流条件下,LDL在血流受扰动区的聚积高于定常流的值;而且.流动分离点处LDL壁面浓度峰值覆盖的区域也宽于定常流。本文所揭示出的LDL在血管狭窄处的质量传输现象可能在动脉粥样硬化的局部性和动脉狭窄的形成中起着很重要的作用。  相似文献   

8.
超空泡射弹是一种新型的水下高速动能武器。基于理想可压缩势流理论,考虑流体的重力效应,建立了水下细长锥形射弹超空泡流动的统一理论模型和数值计算方法,分别导出了亚、超声速条件下用于计算细长锥形射弹超空泡形态的积分-微分方程。采用二次多项式局部拟合空泡,提出了超空泡形态的数值离散和递推求解方法。通过超空泡长细比的渐近解与数值解计算结果比较,验证了所建立的理论模型和计算方法的有效性。通过分析细长锥形射弹在不同运动方式、深度、速度条件下的超空泡形态和流体动力系数计算结果,明确了流体重力和压缩性效应对超空泡尺度、射弹表面压力分布和压差阻力系数的影响。  相似文献   

9.
CFG桩复合地基沉降影响因素分析   总被引:4,自引:0,他引:4  
对绕2D水翼无分离流边界层内的初生空化形态进行了实验研究. 采用高速摄像机观测 了空化初生结构的形态,应用2D-LDV测量了空化初生时翼型周围的流动速度分布,并对实 验结果进行了分析. 结果表明:绕水翼无分离边界层内,初生空化结构中空泡伴随 着近壁湍流拟序结构的发生而出现,在初生空化条件下,形成空化涡结构,大量的微空泡产生于发夹 涡结构中,并在涡结构的猝发过程中出现生成---长大---溃灭---反弹---再溃灭的过程. 初生空 化涡结构具有空泡和近壁拟序结构双重特性.  相似文献   

10.
超空泡流动涉及多相、相变、湍流、可压缩性和非定常特性等复杂情况,亟待发展相应的精细数值模拟方法和计算软件.本文基于均质平衡流理论和输运方程类空化模型,提出了复杂气、汽、水多相的通气空泡流数学模型,采用有限体积方法和SIMPLE算法,建立了求解混合介质的雷诺平均N-S方程、湍流方程、各组分质量分数输运方程的数值模拟方法,自主开发了相应的三维计算程序.模拟了绕圆盘的轴对称通气超空泡流,计算结果与经典的近似公式、半经验公式及试验数据吻合良好,验证了数学模型和数值计算方法能够正确预报通气空泡流场的基本空泡形态和流场动力特性.  相似文献   

11.
空化是发生在水力机械内部的一种水动力现象,其发展具有显著的非定常特性.空化流动中空穴的脱落以及溃灭会诱发结构振动,对水力机械的效率、噪声、安全性等造成影响. 研究空化流动中结构的振动特性具有重要的工程意义. 采用实验的方法研究了绕NACA66 水翼空化流动的空穴形态和水翼振动特性. 实验在一闭式空化水洞中进行. 采用高速摄像技术观测不同空化阶段的空穴形态,应用多普勒激光测振仪测量水翼的振动速度,并通过一套同步系统实现了高速相机和多普勒激光测振仪的同步触发和测量. 采用小波分析方法对不同空化阶段下的空穴形态和水翼振动数据在时域和频域中的特性进行了分析.对云状空化阶段的同步测量结果进行了研究,分析了振动与空穴发展过程的联系. 结果表明,随着空化数的降低,流场经历了无空化、初生空化、片状空化和云状空化4个阶段,水翼的振动强度呈逐渐增大趋势. 在片状空化和云状空化阶段,空穴脱落导致水翼振动,诱发的振动频率与空穴脱落频率相同. 对于云状空化,在附着型空穴生长阶段水翼发生高频小幅度振动,在空穴脉动和断裂脱落期间水翼表现为低频大幅振动.  相似文献   

12.
High speed cine observations of cavitating flow in a duct   总被引:1,自引:0,他引:1  
The dynamics of cavities produced in cavitating flow confined in a duct was studied. The ultimate purpose of the work is to develop models of the flow to assist in predicting cavitation erosion and noise. Observations of the cavitating flow using high speed cine photography allowed confirmation to be made of the shedding mechanism originally described by Knapp, and measurements of the cavity dimensions to be determined as a function of time. It was found that the time for a cavity to collapse was found three times greater than expected from Rayleigh's classical theory.  相似文献   

13.
The present simulation investigates the multiphase cavitating flow around an underwater projectile. Based on the Homogeneous Equilibrium Flow assumption, a mixture model is applied to simulate the multiphase cavitating flow including ventilated cavitation caused by air injection as well as natural cavitation that forms in a region where the pressure of liquid falls below its vapor pressure. The transport equation cavitating model is applied. The calculations are executed based on a suite of CFD code. The hydrodynamics characteristics of flow field under the interaction of natural cavitation and ventilated cavitation is analyzed. The results indicate that the ventilated cavitation number is under a combined effect of the natural cavitation number and gas flow rate in the multiphase cavitating flows.  相似文献   

14.
收缩扩张管内液氮空化流动演化过程试验研究   总被引:1,自引:1,他引:0  
本文基于低温空化试验平台研究了收缩扩张流道内液氮非定常空化流动的演化过程. 试验采用高时空分辨率的高速摄像机对77 K液氮在不同空化数σ下空穴结构的演变进行了精细化的分析和研究. 利用试验得到的空穴长度和面积等数据, 定量分析了液氮空化流动的非定常特性与时空演变规律. 研究结果表明: (1)在相似来流速度和温度条件下, 随着空化数的减小, 液氮空化流动呈现四种典型流型, 空穴长度在2.5 h以内为初生空化、空穴长度在2.5 h ~ 7.5 h之间为片状空化、空穴长度在7.5 h ~ 15 h之间为大尺度云状空化, 空穴长度超过15 h为双云状空化, 且在大尺度云状空化和双云状空化阶段均捕捉到了回射流现象; (2)液氮空化流动从初生空化到双云状空化, 脱落空穴的尺度逐渐增大, 空穴面积脉动的幅值和准周期均有所增加. 同时, 在大尺度云状空化与双云状空化阶段, 喉口处堵塞效应对空化流动的影响显著增强; (3)相比于初生空化, 片状空化、大尺度云状空化以及双云状空化中脱落空穴的移动距离依次增加了0.97倍、2.65倍与2.68倍, 溃灭时间依次增加了1.18倍、3.59倍与4.47倍, 但溃灭速度依次减小了0.10倍、0.20倍与0.30倍. 除此之外, 对于双云状空化阶段, 存在两种显著不同的脱落空穴演化过程.   相似文献   

15.
王畅畅  王国玉  黄彪 《力学学报》2018,50(5):990-1002
为深入研究空化可压缩流动中空泡/空泡团溃灭过程中激波产生、传播及其与空穴相互作用规律,本文采用数值模拟方法对空化可压缩流动空穴溃灭激波特性展开了研究.数值计算基于OpenFOAM开源程序,综合考虑蒸汽相和液相的压缩性,通过在原无相变两相可压缩求解器的控制方程中耦合模拟空化汽液相间质量交换的源项,实现了对空化流动的非定常可压缩计算.利用上述考虑汽/液相可压缩性的空化流动求解器,对周期性云状空化流动进行了数值模拟,并重点研究了空穴溃灭激波特性.结果表明:上述数值计算方法可以准确捕捉到空穴非定常演化过程及大尺度脱落空泡云团溃灭激波现象,大尺度脱落空泡云团溃灭过程分为3个阶段:(1) U型空泡团形成; (2) U型空泡团头部溃灭; (3) U型空泡团腿部溃灭.在U 型空泡团腿部溃灭瞬间,观察到激波产生,并向上游和下游传播,向上游传播的激波与空穴相互作用,导致水翼吸力面新生的附着型片状空穴回缩,直至完全溃灭.并且空穴溃灭激波存在回弹现象, 抑制了下一周期的空化发展.   相似文献   

16.
A computational method is proposed to simulate 3D unsteady cavitating flows in spatial turbopump inducers. It is based on the code FineTurbo, adapted to take into account two‐phase flow phenomena. The initial model is a time‐marching algorithm devoted to compressible flow, associated with a low‐speed preconditioner to treat low Mach number flows. The presented work covers the 3D implementation of a physical model developed in LEGI for several years to simulate 2D unsteady cavitating flows. It is based on a barotropic state law that relates the fluid density to the pressure variations. A modification of the preconditioner is proposed to treat efficiently as well highly compressible two‐phase flow areas as weakly compressible single‐phase flow conditions. The numerical model is applied to time‐accurate simulations of cavitating flow in spatial turbopump inducers. The first geometry is a 2D Venturi type section designed to simulate an inducer blade suction side. Results obtained with this simple test case, including the study of its general cavitating behaviour, numerical tests, and precise comparisons with previous experimental measurements inside the cavity, lead to a satisfactory validation of the model. A complete three‐dimensional rotating inducer geometry is then considered, and its quasi‐static behaviour in cavitating conditions is investigated. Numerical results are compared to experimental measurements and visualizations, and a promising agreement is obtained. Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

17.
《力学快报》2020,10(5):327-332
The transient cavitating flow around the Clark-Y hydrofoil is numerically investigated by the dynamic mode decomposition with criterion. Based on the ranking dominant modes, frequencies of the first four modes are in good accordance with those obtained by fast Fourier transform. Furthermore, the cavitating flow field is reconstructed by the first four modes, and the dominant flow features are well captured with the reconstructed error below 12% when compared to the simulated flow field. This paper offers a reference for observing and reconstructing the flow fields, and gives a novel insight into the transient cavitating flow features.  相似文献   

18.
The interfacial dynamics‐based cavitation model, developed in Part‐1, is further employed for unsteady flow computations. The pressure‐based operator‐splitting algorithm (PISO) is extended to handle the time‐dependent cavitating flows with particular focus on the coupling of the cavitation and turbulence models, and the large density ratio associated with cavitation. Furthermore, the compressibility effect is important for unsteady cavitating flows because in a water–vapour mixture, depending on the composition, the speed of sound inside the cavity can vary by an order of magnitude. The implications of the issue of the speed of the sound are assessed with alternative modelling approaches. Depending on the geometric confinement of the nozzle, compressibility model and cavitation numbers, either auto‐oscillation or quasi‐steady behaviour is observed. The adverse pressure gradient in the closure region is stronger at the maximum cavity size. One can also observe that the mass transfer process contributes to the cavitation dynamics. Compared to the steady flow computations, the velocity and vapour volume fraction distributions within the cavity are noticeably improved with time‐dependent computations. Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号