首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到16条相似文献,搜索用时 109 毫秒
1.
多孔金属夹层板在冲击载荷作用下的动态响应   总被引:14,自引:4,他引:10  
赵桂平  卢天健 《力学学报》2008,40(2):194-206
借助两种有限元软件ABAQUS和 LS_DYNA, 模拟和分析了两种厚度不同的泡沫铝合金夹层板(三明治板)、方孔蜂窝形夹层 板和波纹形夹层板在冲击载荷下的动态响应. 4种夹层板的单位面积密度相同,冲击载荷分 别用泡沫铝子弹与不锈钢子弹模拟. 讨论了泡沫金属夹层板和格构式夹层板在不同冲击 载荷作用下的变形机制,重点在于对夹层板的吸能特性及板内各部分吸能变化规律的探讨. 研究结果表明: 在泡沫子弹冲击下,夹层板主要是通过自身变形来消耗子弹动能,并转化为 自身内能. 厚度为22\,mm的泡沫金属夹层板吸收能量最多,底面变形最小,是结构性能最优的 夹层板;在刚性子弹高速冲击穿透过程中,格构式夹层板的吸能性能比单位面积密度相同的 泡沫金属夹层板的吸能性能更好. 波纹形夹层板的能量吸收能力在4种板中最高.  相似文献   

2.
用数值分析的方法分别对金属、陶瓷、纤维增强复合材料组成的层合板和由陶瓷球填充的金属四边形蜂窝夹芯结构在冲击载荷作用下的抗侵彻性能进行了模拟计算.其中冲击载荷由12.7mm 直径的刚性穿甲弹模拟.研究了不同构型靶板在侵彻过程中对动能量的吸收机理,分析了两种复合靶板各组分材料的吸能特性,并比较了不同靶板的弹道极限速度V50.研究结果表明:在相同面密度条件下,层合复合靶板中具有最强抗弹性能的陶瓷层与纤维层的最佳比例是2.22,其与4340钢均质靶板相比质量减轻了33%;蜂窝填充陶瓷结构的靶板中灌注环氧树脂后其弹道极限速度提高了13%.  相似文献   

3.
撞击载荷下泡沫铝夹层板的动力响应   总被引:2,自引:0,他引:2  
应用泡沫金属子弹撞击加载的方式研究了固支方形夹层板和等质量实体板的动力响应,分别应用激光测速装置和位移传感器测量了泡沫子弹的撞击速度和后面板中心点的位移历史,给出了夹层板的变形与失效模式,研究了子弹冲量、面板厚度、泡沫芯层厚度及芯层密度对夹层板抗撞击性能的影响。结果表明,后面板中心点挠度最大,周边最小,整体变形为穹形,且伴有花瓣形的变形。参数研究表明,通过增加面板厚度或芯层厚度均能有效控制后面板的挠度,改善夹层板的能量吸收能力,结构响应对子弹冲量和芯层密度比较敏感。实验结果对多孔金属夹层结构的优化设计具有一定的参考价值。 更多还原  相似文献   

4.
使用泡沫金属子弹进行冲击可以模拟爆炸载荷的作用, 这一加载技术已被应用于防护结构的抗冲击性能测试中, 然而泡沫子弹作用于被测试结构上的真实载荷以及二者间的相互作用过程尚不明晰. 本文以泡沫子弹冲击固支梁的情形为例, 开展了对该冲击过程的理论分析和数值模拟研究. 基于泡沫材料的冲击波模型与固支单梁的结构冲击动力学响应模型, 构建了描述泡沫子弹冲击固支梁过程的耦合分析模型. 给出了不同响应阶段下子弹和单梁的动力学控制方程, 并采用Runge-Kutta方法得到了方程的数值解. 基于三维Voronoi技术, 建立了泡沫子弹冲击固支单梁的有限元模型并进行了数值模拟. 通过与有限元模拟结果的对比发现, 相较于经典的脉冲加载模型, 耦合分析模型能更好地预测泡沫子弹和单梁的速度变化规律, 也能准确地预测子弹对单梁的真实冲击压强. 当泡沫子弹的初始动量相同时, 由于子弹自身的压溃行为, 子弹的初始冲击速度、密度和长度的改变都会对冲击过程产生影响. 最后, 通过耦合分析模型分别分析了泡沫子弹的密度、长度、初速度对冲击压强的峰值、衰减速度和持续时间的影响, 并针对具有不同特征的目标模拟载荷给出了泡沫子弹的筛选策略. 所构建的耦合分析模型为研究泡沫子弹与被测试结构之间的相互作用规律以及泡沫子弹的设计提供了理论基础.   相似文献   

5.
利用实验研究与理论分析相结合的方法研究了泡沫铝填充金属薄壁圆管在准静态侧向压缩下的力学响应.基于能量法,建立了泡沫铝填充圆管和金属薄壁圆管在侧向均匀压缩时的瞬时侧向力、平均侧向力和总吸能的理论公式.对泡沫铝填充管与金属薄壁圆管进行了准静态侧向压缩实验,并且将实验结果与理论公式进行了对比,结果表明理论预测值与实验结果吻合较好.基于建立的理论分析模型,研究了管的几何尺寸以及泡沫铝材料的密度对结构的瞬时侧向力、平均侧向力、总吸能和比吸能的影响.结果表明,在准静态侧向压缩下,泡沫铝填充管的总吸能大于对应的金属薄壁圆管;泡沫铝填充管的侧向压缩力和总吸能随管长度、壁厚和直径的增加而增大;当填充材料泡沫铝密度增大时,填充管的总吸能与侧向压缩力均增加.  相似文献   

6.
利用实验研究与理论分析相结合方法研究了泡沫铝填充金属薄壁圆管在准静态侧向压缩下的力学响应。基于能量法,建立了泡沫铝填充圆管和金属薄壁圆管在侧向均匀压缩时的瞬时侧向力、平均侧向力和总吸能的理论公式。对泡沫铝填充管与金属薄壁圆管进行了准静态侧向压缩实验,并且将实验结果与理论公式进行了对比,结果表明理论预测值与实验结果吻合较好。基于建立的理论分析模型,研究了管的几何尺寸以及泡沫铝材料的密度对结构的瞬时侧向力、平均侧向力、总吸能和比吸能的影响。结果表明,在准静态侧向压缩下,泡沫铝填充管的总吸能大于对应的金属薄壁圆管;泡沫铝填充管的侧向压缩力和总吸能随管长度、壁厚和直径的增加而增大;当填充材料泡沫铝密度增大时,填充管的总吸能与侧向压缩力均增加。  相似文献   

7.
应用一级轻气炮驱动泡沫铝弹丸高速撞击加载技术,对实心钢板以及前/后面板为Q235钢板、芯层分别为铝基复合泡沫和普通泡沫铝的夹层板结构,在脉冲载荷作用下的动态力学响应进行实验研究。结果表明:泡沫铝子弹高速撞击靶板可近似模拟爆炸载荷效果;铝基复合泡沫夹层板的变形分为芯层压缩和整体变形两个阶段;与其他靶板相比,铝基复合泡沫夹层板的抗冲击性能最优。基于实验研究,应用LS-DYNA非线性动力有限元软件,对泡沫铝夹层板的动态响应进行数值模拟。结果表明:泡沫铝子弹的长度和初始速度对子弹与夹层板之间的接触作用力影响显著,并且呈线性关系。泡沫芯层强度对等质量及等厚度夹层板的抗冲击性能均有显著影响,夹层板中心挠度对前、后面板的厚度匹配较为敏感,在临界范围内,若背板厚度大于面板厚度,可减小夹层板的最终挠度。夹层板面板宜采用刚度较低、延性好、拉伸破坏应变较大的金属材料。  相似文献   

8.
对AA5052铝合金泡沫金属夹层板进行自冲铆接试验,对接头的可连接性进行探究。通过静力学试验对比各组接头的静力学性能,分析不同种类泡沫金属对自冲铆接头力学性能的影响;用扫描电子显微镜对接头典型断口进行研究,分析其微观失效机理。结果表明:自冲铆技术可以实现泡沫金属夹层板的有效连接,接头具有良好的成形质量;泡沫金属夹层提高了自冲铆接头的静力学性能,其中泡沫镍夹层使AA5052自冲铆接头静失效载荷提高了4.1%;夹层板自冲铆接头失效形式均为铆钉与下板分离,其中泡沫铁镍夹层自冲铆接头下板铆扣断裂区域粘附在铆钉脚底部,为韧性断裂机制;下板内锁区域失效时铆钉与下板发生剧烈刮擦,呈现具有分层现象的片状组织。  相似文献   

9.
李勇  肖伟  程远胜  刘均  张攀 《爆炸与冲击》2018,38(2):279-288
通过有限元软件LS-DYNA模拟了波纹杂交夹层板在冲击波与破片联合作用下的响应过程,研究了炸药当量、载荷类型和填充方式对波纹杂交夹层板变形与失效模式的影响,并与实体板、间隔板和波纹夹层板的抗联合毁伤性能进行了对比,讨论了波纹杂交夹层板的能量吸收特性。数值计算结果表明:与冲击波单独作用相比,破片群单独作用和冲击波与破片联合作用对结构造成的毁伤更为严重;当药量较小时,波纹夹层板和波纹杂交夹层板的抗联合毁伤性能优于实体板与间隔板,波纹杂交夹层板的抗联合毁伤性能从全填充、迎爆面填充到背爆面填充逐渐降低;当药量较大时,所有结构均产生破口失效;在能量耗散方面,冲击波单独作用时以波纹芯层吸能为主,破片群单独作用和冲击波与破片联合作用时以上面板吸能为主。  相似文献   

10.
利用INSTRON-1185型万能材料试验机在准静态加载环境下对不同密度的聚氨酯泡沫的抗压、抗拉及抗弯性能进行了较系统的实验研究,分析了聚氨酯泡沫材料的力学性能及吸能特性随表观密度的变化规律.研究表明,聚氨醋泡沫材料的杭压性能优于其杭拉性能,该材料具有良好的吸能特性,且其吸能特性随密度的增大而提高.  相似文献   

11.
3种点阵金属三明治板的抗侵彻性能模拟分析   总被引:3,自引:0,他引:3  
对3种不同的点阵金属芯体三明治板受钢质弹丸侵彻作用下的抗侵彻性能进行了有限元模拟研究,包括空心金字塔三明治板、嵌入陶瓷柱金字塔三明治板和注入环氧树脂陶瓷金字塔三明治板.随着结构、材料复杂性的递增,以期望从中得出各子结构、各材料在三明治板抗侵彻过程中的吸能表现.弹丸作用于板的入射速度及出射速度也是关注的重要参数,用以量化确定三明治结构各组分对弹丸的弹道极限和抗侵彻能力的影响.研究表明,陶瓷材料因其具有高强度和高硬度等特点,可以显著提高金属三明治板结构的抗侵彻能力;环氧树脂材料可使离散的板结构保持整体性,在三明治板受侵彻作用时,吸收大量能量,从而实现大幅提高结构的抗侵彻性能的目的;因其材料/结构的完备性,注入环氧树脂陶瓷金字塔三明治板具有最高的弹道极限速度,抗侵彻能力也最强.  相似文献   

12.
The dynamic responses of clamped circular monolithic and sandwich plates of equal areal mass have been measured by loading the plates at mid-span with metal foam projectiles. The sandwich plates comprise AISI 304 stainless steel face sheets and aluminium alloy metal foam cores. The resistance to shock loading is quantified by the permanent transverse deflection at mid-span of the plates as a function of projectile momentum. It is found that the sandwich plates have a higher shock resistance than monolithic plates of equal mass. Further, the shock resistance of the sandwich plates increases with increasing thickness of sandwich core. Finite element simulations of these experiments are in good agreement with the experimental measurements and demonstrate that the strain rate sensitivity of AISI 304 stainless steel plays a significant role in increasing the shock resistance of the monolithic and sandwich plates. Finally, the finite element simulations were employed to determine the pressure versus time history exerted by the foam projectiles on the plates. It was found that the pressure transient was reasonably independent of the dynamic impedance of the plate, suggesting that the metal foam projectile is a convenient experimental tool for ranking the shock resistance of competing structures.  相似文献   

13.
采用有限元方法研究爆炸载荷下四边固支孔结构金属复合夹芯板的动力响应及吸能特性,给出了孔结构金属复合夹芯板的动力响应过程,得到夹芯板的变形模式,比较了孔结构金属复合夹芯板与非孔结构金属复合夹芯板的抗爆炸冲击性能,同时讨论了孔大小、间距、排布方式和面板质量分布等因素对孔结构金属复合夹芯板抗爆炸冲击性能的影响。研究结果表明,迎爆面外面板的孔设计使爆炸冲击波穿过孔洞直接作用在芯材上,增强了芯材的压缩,从而提高了夹芯板的能量吸收能力。同等面密度情况下,内外面板厚度比大于1的孔结构金属复合夹芯板变形挠度小于内外面板厚度比小于1的孔结构金属复合夹芯板。进一步研究发现,通过合理设计内外面板的质量分布,可以使孔结构金属复合夹芯板的抗爆炸冲击性能最优。  相似文献   

14.
A blast-tolerant sandwich plate design with a polyurea interlayer   总被引:1,自引:0,他引:1  
This paper presents a study of both conventional and modified sandwich plate designs subjected to blast loads. The conventional sandwich Design (1) consists of thin outer (loaded side) and inner facesheets made of fibrous laminates, separated by a layer of structural foam core. In the modified Design (2), a thin polyurea interlayer is inserted between the outer facesheet and the foam core. Comparisons of the two designs are made during a long time period of 5.0 ms, initiated by a pressure impulse lasting 0.05 ms applied to a single span of a continuous plate. In the initial response period the overall deflections are limited and significant foam core crushing is caused in the conventional design by the incident compression wave. This type of damage is much reduced in the modified design, by stiffening of the polyurea interlayer under shock compression, which provides support to the outer facesheet and alters propagation of stress waves into the foam core. This benefits the long term, bending response and leads to significant reductions in facesheet strains and overall deflection. The total kinetic energy of the modified sandwich plate is much lower than that of a conventionally designed plate, and so is the stored and dissipated strain energy. Similar reductions are found when the conventional and the enhanced sandwich plates have equal overall thickness or equal total mass.  相似文献   

15.
One-dimensional response of sandwich plates to underwater shock loading   总被引:5,自引:0,他引:5  
The one-dimensional shock response of sandwich plates is investigated for the case of identical face sheets separated by a compressible foam core. The dynamic response of the sandwich plates is analysed for front face impulsive loading, and the effect of strain hardening of the core material is determined. For realistic ratios of core mass to face sheet mass, it is found that the strain hardening capacity of the core has a negligible effect upon the average through-thickness compressive strain developed within the core. Consequently, it suffices to model the core as an ideally plastic-locking solid. The one-dimensional response of sandwich plates subjected to an underwater pressure pulse is investigated by both a lumped parameter model and a finite element (FE) model. Unlike the monolithic plate case, cavitation does not occur at the fluid-structure interface, and the sandwich plates remain loaded by fluid until the end of the core compression phase. The momentum transmitted to the sandwich plate increases with increasing core strength, suggesting that weak sandwich cores may enhance the underwater shock resistance of sandwich plates.  相似文献   

16.
The dynamic response of fully clamped, monolithic and sandwich plates of equal areal mass has been measured by loading rectangular plates over a central patch with metal foam projectiles. All plates are made from AISI 304 stainless steel, and the sandwich topologies comprise two identical face-sheets and either Y-frame or corrugated cores. The resistance to shock loading is quantified by the permanent transverse deflection at mid-span of the plates as a function of projectile momentum. At low levels of projectile momentum both types of sandwich plate deflect less than monolithic plates of equal areal mass. However, at higher levels of projectile momentum, the sandwich plates tear while the monolithic plates remain intact. Three-dimensional finite element (FE) calculations adequately predict the measured responses, prior to the onset of tearing. These calculations also reveal that the accumulated plastic strains in the front face of the sandwich plates exceed those in the monolithic plates. These high plastic strains lead to failure of the front face sheets of the sandwich plates at lower values of projectile momentum than for the equivalent monolithic plates.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号