变形模式对多孔金属材料SHPB实验结果的影响

利用两种改进后的Hopkinson杆实验分别测得多孔金属材料冲击端和支撑端的应力.实验结果及高速摄影表明,随着撞击速度的增加,试件两端的应力均匀性变差,分别对应着泡沫材料的3种变形模式:准静态模式、过渡模式、冲击模式.实验得出在冲击模式下,冲击端与支撑端的应力与试件的厚度无关,但是与试件的密度有关.在多孔金属的高应变率实验中,变形模式对SHPB实验有很大的影响,轴向惯性(波动)效应会导致试件两端的应力不均匀,此时利用SHPB得出的实验结果将会是应变率效应和惯性效应的耦合,不能真实反映材料的动态力学性能(应变率效应).     

岩石SHPB实验加载过程中应力平衡问题分析

运用一维应力波理论,分析了弹性应力波在分离式Hopkinson压杆(SHPB)实验中的传播过程,推 导出试件和压杆中应力分布相关计算公式。探讨了有关因素对试件应力平衡时间的影响规律,发现试件应力 平衡时间受试件/压杆广义波阻抗比和入射加载升时的影响显著,而不受试件/压杆截面积比和入射加载应力 幅值的影响。结合岩石SHPB实验,计算分析了不同入射加载应力幅值在不同入射加载升时情况下,试件达 到应力平衡时的应变变化特征,并提出了降低试件在应力平衡时的应变控制方法,使试件在未达到断裂应变 之前达到应力平衡,以保证实验的有效性。得出的结论对岩石类脆性材料SHPB实验方案设计具有一定的 参考意义。     

Laplace变换法研究SHPB实验中试件的黏弹性波传播问题

对分离式霍普金森压杆(split Hopkinson pressure bar,SHPB)实验中试件的黏弹性波传播的控制方程组进行Laplace变换,并结合恰当的初始-边界条件求解,得到变换域的应力、速度、应变等变量的像函数的精确表达式.采用该方法处理SHPB实验中涉及黏弹性试件内部应力非均匀性问题,并给出数值反变换解.作为特例,对于弹性试件分别采用级数展开法和留数定理进行反Laplace变换,从而给出弹性夹层介质中应力波传播问题的解析解.     

USING LAPLACE TRANSFORM TO SOLVE THE VISCOELASTIC WAVE PROBLEMS IN THE SHPB EXPERIMENTS

对分离式霍普金森压杆(split Hopkinson pressure bar, SHPB) 实验中试件的黏弹性波传播的控制方程组进行Laplace 变换,并结合恰当的初始-边界条件求解,得到变换域的应力、速度、应变等变量的像函数的精确表达式. 采用该方法处理SHPB 实验中涉及黏弹性试件内部应力非均匀性问题,并给出数值反变换解. 作为特例,对于弹性试件分别采用级数展开法和留数定理进行反Laplace 变换,从而给出弹性夹层介质中应力波传播问题的解析解.     

基于数字图像相关性方法的脆性材料拉氏反分析实验技术

利用分离式Hopkinson压杆作为加载系统，借助超高速数字图像相关性分析方法，发展了长杆试件拉氏反分析实验技术，并用于研究脆性材料在小变形条件下的动态本构特性。通过超高速相机实时拍摄冲击加载下长杆试件变形的散斑图像，再对散斑图像进行数字图像相关性（digital image correlation，DIC）分析，获得长杆试件表面速度场和应变场。随后，以脆性材料PMMA（polymethyl methacrylate）为例，从DIC分析得到的速度场中提取出不同拉格朗日位置上质点速度时程曲线，构建路径线连接整个速度场，再结合零初始条件，数值求解得到了试件中的应力时程曲线，消去时间参数后，获得了脆性材料PMMA的动态应力-应变曲线，并与Hopkinson压杆实验和准静态压缩实验的结果进行了对比，揭示了PMMA材料在小应变条件下的黏弹性本构响应特征。     

921A钢纯剪切帽状试件在SHPB实验中的动态变形

应用ANSYS/LS-DYNA软件,开展了一系列基于921A钢纯剪切帽状试件的SHPB数值模拟.结合SHPB系统应力波理论,研究不同加载速率v0(或应力脉冲I(t))下,特别是高应变率(约106 s-1)下的压杆轴向应变波形以及相应的试件动态变形特性,并对高速撞击下压杆中应变波形的适用性作了相关讨论.     

混凝土一维应力层裂实验的全场DIC分析

基于74 mm直径分离式Hopkinson杆(SHPB)实验平台进行了混凝土杆的一维应力层裂实验.采用超高速相机(采样频率:2μs/frame)结合数字图像相关法(DIC),记录混凝土试件中的动态位移场实时变化情况,探讨了混凝土在拉伸断裂过程中的表面位移场及速度场演化规律.针对实验中出现的多重层裂现象,基于一维应力波传播理论,指出各个位置在发生层裂时,其最大拉应力均由透射压缩波与反射拉伸波叠加而成,各处层裂发生时均处于一维应力状态.并提出了根据层裂位置左右两点速度趋势变化判断层裂发生时刻的判据.该判据可以给出所有层裂的起裂时间,结合DIC分析直接给出了混凝土多重层裂应变.结果显示混凝土的拉伸强度具有明显的应变率效应,在30 s~(-1)的应变率下,其拉伸强度的动态增强因子(DIF)可以达到5.与传统的波叠加法和自由面速度回跳法相比,DIC全场分析法不受加载波形限制,可以精确给出每个层裂的位置和起裂时间,从而得到试件在高应变率加载下不同位置处的断裂应变、拉伸强度及相应应变率,提高了测量效率.     

混凝土一维应力层裂实验的全场DIC分析

基于74mm直径分离式Hopkinson杆(SHPB)实验平台进行了混凝土杆的一维应力层裂实验.采用超高速相机(采样频率:2 $\mu$s/frame)结合数字图像相关法(DIC),记录混凝土试件中的动态位移场实时变化情况,探讨了混凝土在拉伸断裂过程中的表面位移场及速度场演化规律.针对实验中出现的多重层裂现象,基于一维应力波传播理论,指出各个位置在发生层裂时,其最大拉应力均由透射压缩波与反射拉伸波叠加而成,各处层裂发生时均处于一维应力状态.并提出了根据层裂位置左右两点速度趋势变化判断层裂发生时刻的判据.该判据可以给出所有层裂的起裂时间,结合DIC分析直接给出了混凝土多重层裂应变.结果显示混凝土的拉伸强度具有明显的应变率效应,在30 s$^{-1}$的应变率下,其拉伸强度的动态增强因子(DIF)可以达到5.与传统的波叠加法和自由面速度回跳法相比,DIC全场分析法不受加载波形限制,可以精确给出每个层裂的位置和起裂时间,从而得到试件在高应变率加载下不同位置处的断裂应变、拉伸强度及相应应变率,提高了测量效率.      

SHPB系统圆柱形试件的惯性效应分析

在对分离式Hopkinson压杆(SHPB)实验系统试件惯性效应分析的基础上,增加了界面摩擦做功对试件惯性效应影响的分析．在理论分析的基础上,就如何减小摩擦效应、惯性效应对实验结果的影响,对SHPB试件尺寸比例的设计以及摩擦系数的选取作了进一步的分析,另外还对SHPB实验过程中,试件两端应力平衡情况做了初步的讨论．     

采用改进的SHPB方法对泡沫铝动态力学性能的研究

本文改进了传统的分离式霍布金森压杆(SHPB)技术，采用夹在透射杆中的PVDF压电计直接测量透射杆中的应力时程．同时，采用输入波形整形技术，通过调整加载波形，使试样加载过程中保证均匀变形及应力平衡．利用此改进了的SHPB技术对泡沫铝进行了高应变率下的动态压缩实验．实验结果表明：泡沫铝的动态应力应变曲线具有泡沫材料的应力应变曲线的“三阶段”特征(elastic region，collapse region and densification region)，并且应变率对其力学性能影响明显．     

Flattened Brazilian Disc Method for Determining the Dynamic Tensile Stress-Strain Curve of Low Strength Brittle Solids

An indirect tensile testing method is proposed to measure the full dynamic tensile stress-strain curve of low strength brittle solids. In this method, the flattened-Brazilian disc (FBD) sample is loaded by modified split Hopkinson pressure bars (SHPB) system. Low amplitude dynamic forces were measured with a pair of piezoelectric force transducers embedded in the incident bar and the transmitted bar. The evolution of tensile stress at the center of the disc sample was determined through finite element analyses using the measured stress in SHPB as inputs. In a traditional Brazilian test, a strain gauge is mounted at the center of the specimen to measure the tensile strain, which is difficult to apply for low strength brittle materials. Thus, two types of non-contact methods, the Digital Image Correlation (DIC) technique and the Laser Gap Gauge (LGG), were used to measure the strain. The DIC method was used to monitor the displacement and the strain map of the specimen during the test, from which the strain at the center of the specimen can be obtained. The accuracy of the DIC results was assessed, and the displacement and strain uncertainties of our system were 0.003 mm and 0.003, respectively. LGG was used to monitor the expansion of the disc perpendicular to the loading axis, from which the average tensile strain is deduced. The numerical simulation revealed that the tensile strain at the center of the specimen is proportional to the average tensile strain and that the ratio is not sensitive to the material elastic parameters. The strain measured through LGG was compared with that measured by the DIC method using photos captured with a synchronized high-speed camera. The result of the LGG method was 20 % smaller than that of the DIC process. However, the latter was limited by the number of frames of the high-speed camera. The feasibility of this methodology was demonstrated using a polymer-bonded explosive (PBX).     

Full Field Strain Measurement in Compression and Tensile Split Hopkinson Bar Experiments

The 3D image correlation technique is used for full field measurement of strain (and strain rate) in compression and tensile split Hopkinson bar experiments using commercial image correlation software and two digital high-speed cameras that provide a synchronized stereo view of the specimen. Using an array of 128 × 80 (compression tests) and 258 × 48 (tensile tests) pixels, the cameras record about 110,000 frames per second. A random dot pattern is applied to the surface of the specimens. The image correlation algorithm uses the dot pattern to define a field of overlapping virtual gage boxes, and the 3-D coordinates of the center of each gage box are determined at each frame. The coordinates are then used for calculating the strains throughout the surface of the specimen. The strains determined with the image correlation method are compared with those determined from analyzing the elastic waves in the bars, and with strains measured with strain gages placed on the specimens. The system is used to study the response of OFE C10100 copper. In compression tests, the image correlation shows a nearly uniform deformation which agrees with the average strain that is determined from the waves in the bars and the strains measured with strain gages that are placed directly on the specimen. In tensile tests, the specimen geometry and properties affect the outcome from the experiment. The full field strain measurement provides means for examining the validity and accuracy of the tests. In tests where the deforming section of the specimen is well defined and the deformation is uniform, the strains measured with the image correlation technique agree with the average strain that is determined from the split Hopkinson bar wave records. If significant deformation is taking place outside the gage section, and when necking develops, the strains determined from the waves are not valid, but the image correlation method provides the accurate full field strain history.     

两点应变测量法在SHPB测量技术上的运用

介绍了两点应变测量法在分离式Hopkinson压杆 (SHPB)测量技术上的运用。该方法通过测量一根压杆两个不同地方的应变 ,利用一个简单的反复过程将压杆中相对传播并叠加在一起的右行波与左行波分离 ,从而利用输入杆对试件的多次加载来研究软材料的动态力学性能。利用该方法计算所得的最大应变比利用传统SHPB测量技术得到的最大应变增大了 2～ 3倍。     

A quartz-crystal-embedded split Hopkinson pressure bar for soft materials

A dynamic experimental technique that is three orders of magnitude as sensitive in stress measurement as a conventional split Hopkinson pressure bar (SHPB) has been developed. Experimental results show that this new method is effective and reliable for determining the dynamic compressive stress-strain responses of materials with low mechanical impedance and low compressive strengths, such as elastomeric materials and foams at high strain rates. The technique is based on a conventional SHPB. Instead of a surface strain gage mounted on the transmission bar, a piezoelectric force transducer was embedded in the middle of the transmission bar of a high-strength aluminum alloy to directly measure the weakly transmitted force profile from a soft specimen. In addition, a pulse-shape technique was used for increasing the rise time of the incident pulse to ensure stress equilibrium and homogeneous deformation in the low-impedance and low-strength specimen.     

泡沫铝在SHPB高温动态下的变形过程研究

利用分离式Hopkinson压杆(SHPB)实验装置研究轻质泡沫铝在动态压缩下的温度相关性,重点设计了一种基于SHPB的可视化高温炉,在此基础上通过高速摄影观测泡沫铝试件在高低温且动态压缩下的变形过程。动态加载下的实验结果表明：常温下,胞壁在变形过程中易于观察到屈曲失稳、撕裂、弯曲等现象,且在压缩的过程中碎片飞溅;高温下材料软化较明显,呈现出更多的塑性弯曲现象,但是屈曲失稳与撕裂的现象并不显著,变形过程中并无碎片产生。     

Experimental Study of the Dynamic Flexural Strength of Concrete

In this paper, we analyze the increase in the dynamic flexural strength of concrete according to strain rate. A simple beam with center-point loading and a classical electro-mechanical testing machine are used to determine the static flexural strength. The dynamic measurements are conducted using a split Hopkinson pressure bar (SHPB) device in the same three-point bending configuration. The outer faces of the beams are instrumented with strain gauges to record the extreme tensile strains. Moreover, full-field displacement measurements are obtained using digital image correlation (DIC) on images recorded by a very high-speed camera. The strain gauge and DIC measurements are compared and used to determine the onset of failure and to evaluate the rate-related tensile strength. Several tests are performed at strain rates in the range from 1/s to 15/s. As expected, a significant increase in the flexural tensile strength with strain-rate is observed, which is consistent with results from the literature.     

一种用于软材料测试的改进SHPB装置

本文提出了一种新的、用于测试橡胶、高弹体及高聚物软泡沫材料动态力学性能的SHPB改进装置。该装置取消了常见的入射杆而采用长杆弹直接撞击试件从而实现了持续的长时间加载，使得在相当大的应变率范围内试件的最大应变在一个加载过程中即可达到。配合该装置采用了瞬态响应优良、分辨率良好的光电式位移测试系统来测量试件的变形；为记录微弱的应变信号，在透射杆中使用了半导体应变片。本方案克服了传统SHPB在测试软材料时由于子弹长度限制带来的加载幅度不足及由于阻抗失配导致的应变信号微弱的困难；与采用高聚物杆的SHPB改进方案相比，本方案的测试结果也更为可靠。在试验装置中还运用了加载整形技术以改善试件中的应力均匀性。从测试结果看，该装置能有效地实现大变形范围、近似恒应变率持续加载以及相应的微弱应变信号的测量。     

Loading and unloading split hopkinson pressure bar pulse-shaping techniques for dynamic hysteretic loops

Pulse-shaping techniques are developed for both the loading and unloading paths of a split Hopkinson pressure bar (SHPB) experiment to obtain valid dynamic stress-strain loops for engineering materials. Front and rear pulse-shapers, in association with a momentum trap, are used to precisely control the profiles of the loading and unloading portions of the incident pulse. The modifications, ensure that the specimen deforms at the same constant strain rate under dynamic stress equilibrium during both loading and unloading stages of an experiment so that dynamic stress-strain loops can be accurately determined. Dynamic stress-strain loops with a constant strain rate for a nickel-titanium shape memory alloy and polymethyl methacrylate are determined using the modified SHPB. The modified momentum trap prevents repeated loading on a specimen without affecting the amplitude of the desired loading pulse and without damaging the bar at high stress levels.