大理岩动态劈裂拉伸的SHPB实验研究

利用直径100 mm的Hopkinson压杆和薄圆形铝片作为波形整形器,用不同弹速径向冲击平台巴西圆盘试样以研究大理岩的动态拉伸强度。分析了试样的应变率、破坏时间、破坏模式,以及破坏过程中的载荷-应变关系,得到了关于大理岩在高应变率下拉伸强度及弹性模量的一些结论。考虑了试样的尺寸大小及两个平台附近应力的时间不均匀性与空间不均匀性对实验结果的影响。同时,利用有限元法对平台巴西圆盘试样的动态应力分布进行了数值模拟,验证了动态劈裂拉伸实验的有效性。     

大理岩的高应变率动态劈裂实验

首次把平台巴西圆盘试样引入动态劈裂试验。利用直径100mm的分离式Hopkinson杆对大理岩巴西圆盘和平台巴西圆盘试样进行了动态劈裂实验。结合有限元分析,得到了大理岩的动态劈裂破坏的拉伸强度。分析了巴西圆盘和平台巴西圆盘的典型破坏方式。结果表明,大理岩的动态拉伸强度随着应变率的提高而增加。利用圆盘中心粘贴的应变片来测大理岩等脆性材料的动态拉伸强度,是一种简便高效的试验方法。和巴西圆盘相比,平台巴西圆盘具有更大的优越性和更好的测量效果。     

岩石动态巴西圆盘实验中的过载现象

巴西圆盘实验是国际岩石力学与工程学会（ISRM）推荐的测量岩石静态拉伸强度的方法之一,也是该学会推荐的唯一测量岩石动态拉伸强度的方法。但是巴西圆盘实验得到的静态或者动态拉伸强度往往较真实值偏大,其中一个原因是所谓的过载现象,而且其相应的过载效应在动态巴西圆盘测试中尤为明显。为探究岩石材料动态劈裂拉伸强度的过载效应机理及其率相关性,利用SHPB实验装置开展了不同加载率条件下的动态巴西圆盘实验,对岩石材料劈裂拉伸强度的过载特性进行了定量分析;结合颗粒流程序进行了相关实验的数值模拟,得到了圆盘破裂的微观过程。结果表明:（1）动态巴西圆盘实验得到的岩石拉伸强度存在明显的过载现象,圆盘试样拉伸强度的过载比随加载率增加呈对数形式增加;（2）依据动态拉伸强度实验结果对模型参数引入率相关性后,模拟观察到的过载效应更加贴近实验观测。这些结果表明巴西圆盘实验中拉伸强度的过载现象是客观存在的,其机理与试样的圆盘构型以及测试方法有关。结合实验和数值结果,解释了巴西圆盘实验的过载机理,证明了动态巴西圆盘实验修正的必要性并给出了相应的方案,以获取岩石材料的真实动态拉伸强度。     

大理岩动态劈裂拉伸断裂的实验研究

利用直径为100mm的Hopkinson压杆和薄圆形铝片作为波形整形器,用不同弹速径向冲击大理岩平台巴西圆盘来研究其动态拉伸强度.考虑了试样的尺寸大小及两个平台附近应力的时间不均匀性与空间不均匀性对实验结果的影响.分析了试样的最大应变率、破坏时间、破坏模式以及破坏过程中的载荷应变关系,得到了关于大理岩在高应变率下拉伸强度及弹性模量的一些结论.进一步又利用该装置径向冲击人字形切槽巴西圆盘试样,对试样的起裂时间进行了初步的研究,以便今后测试动态断裂韧度.     

钢纤维活性粉末混凝土的动态力学性能

利用?74mmSHPB实验装置对钢纤维活性粉末混凝土(RPC)进行动态压缩实验和动态劈裂拉 伸实验。获得了钢纤维RPC在1~102s-1应变率加载下的动态力学参数。对试件内的动态应力分布进行数 值模拟,验证了动态实验的有效性。结果表明,钢纤维RPC的动态压缩和动态劈裂拉伸的力学性能均表现出 显著的应变率效应。随着应变率的增加,钢纤维RPC冲击压缩破坏应力、冲击压缩破坏应变、弹性模量、动态 劈裂拉伸破坏应力均有一定程度的增加,动态拉压比相对静态拉压比也有显著的提高。     

岩石巴西圆盘动态劈裂的流形元法模拟

利用二阶流形元法，通过引入裂纹产生与扩展判据，对冲击载荷作用下岩石平台巴西圆盘的动态拉伸劈裂过程进行了数值模拟，再现拉伸波作用下圆盘被劈裂的过程。模拟现象与实验结果相符，动态平衡时的应力分布与有限元结果基本一致。从而验证了流形元在模拟冲击载荷作用下材料动态破坏过程的有效性和可行性。     

轻质泡沫混凝土的劈裂破坏力学行为分析

利用平台巴西圆盘加载方式和钢质压条加载方式,对两种厚度为25mm和50mm、不同密度的轻质泡沫混凝土(400～1000kg/m3)进行巴西圆盘劈裂试验,研究密度和厚度对泡沫混凝土裂纹宽度、劈裂强度、断裂韧度、断裂能的影响规律。结果表明,在橡胶垫平台巴西圆盘和钢质压条加载方式下,其劈裂断裂特征大致分为四个阶段:线性弹性段、非线性弹性段、起裂阶段、失稳阶段。同样加载率下最大裂纹宽度随着泡沫混凝土密度增加逐渐减小,劈裂拉伸强度、断裂韧度、断裂能呈幂函数形式增加。借鉴Reinhardt非线性软化曲线,对不同密度泡沫混凝土的应力软化关系进行曲线拟合,建立基于拉伸强度、断裂韧度等控制参数的应力-裂纹宽度关系三段式模型。基于试验结果,对理想多孔材料细观力学预测模型进行修正,获得泡沫混凝土孔隙率与拉伸强度的半经验公式。     

基于平台圆环试样的无机玻璃动态拉伸性能研究

无机玻璃的拉伸强度往往远小于压缩强度，服役过程中玻璃大多会发生拉伸断裂.论文采用平台圆环(flattened circular ring, FCR)试样测试钠钙硅酸盐玻璃的拉伸性能.分别利用电子万能试验机和电磁分离式Hopkinson压杆(electromagnetic split Hopkinson pressure bar, ESHPB)开展准静态、动态单轴单向和单轴双向实验，加载过程中采用高速相机对试样的破坏过程进行观测.结果显示，该材料试样强度具有明显的正加载速率相关性.动态单轴双向加载可比单向加载更快实现应力平衡，但两种应力波加载方式下试样的动态拉伸强度大致相同.高速摄像与动态加载同步分析表明，这是因为试样的裂纹产生时刻与应力峰值时刻几乎同时产生.对三种形式的拉伸实验结果进行对比，发现拉伸强度受试样形状影响，这与试样断裂路径上的拉伸应力分布有关.     

混凝土类材料动态拉伸强度的微观力学模型

基于水泥砂浆试样动态劈裂拉伸实验,研究了不同加载速率下水泥砂浆材料动态劈裂时的裂纹发 生和扩展规律,提出一个微观力学模型。结果表明,微裂纹惯性是混凝土类材料动态拉伸实验中测量到的动 态拉伸强度随应变率的增加而提高的一种微观机制。     

不同加载边界下混凝土巴西劈裂过程及强度的DIC实验分析

平板、垫条、圆弧压模及平台试样等不同加载方式下, 脆性材料巴西劈裂实验结果的差异一直是人们所讨论的问题. 本文设计了混凝土平板直接加载与采用垫条加载实验, 采用理论、高速相机与数字图像相关法(digital image correlation, DIC)相结合的方法, 对试样表面应变场演化、起裂位置及裂纹扩展过程进行分析, 探讨了不同的加载边界对试样应变集中演化及劈裂拉伸强度结果的影响. 结果显示: (1)混凝土拉伸非线性特性导致的应变集中演化对不同加载条件非常敏感, 平板加载时应变集中较早在加载端起始并向中心演化, 即使满足巴西实验"中心起裂"条件, 其强度仍低于垫条加载情况, 两者差别达17.9%; (2)如果软垫条加载接触角合理设计, 与平板直接加载相比, 其应力场更稳定, 有利于保证圆盘试样的应变集中及断裂均从中心起始, 更好满足巴西劈裂实验条件; (3)仅校验巴西实验 "中心起裂"有效性条件是不充分的, 设计时必须谨慎考虑. 研究结果对脆性材料巴西劈裂实验设计、测试分析具有重要参考意义.      

Flattened Brazilian Disc Method for Determining the Dynamic Tensile Stress-Strain Curve of Low Strength Brittle Solids

An indirect tensile testing method is proposed to measure the full dynamic tensile stress-strain curve of low strength brittle solids. In this method, the flattened-Brazilian disc (FBD) sample is loaded by modified split Hopkinson pressure bars (SHPB) system. Low amplitude dynamic forces were measured with a pair of piezoelectric force transducers embedded in the incident bar and the transmitted bar. The evolution of tensile stress at the center of the disc sample was determined through finite element analyses using the measured stress in SHPB as inputs. In a traditional Brazilian test, a strain gauge is mounted at the center of the specimen to measure the tensile strain, which is difficult to apply for low strength brittle materials. Thus, two types of non-contact methods, the Digital Image Correlation (DIC) technique and the Laser Gap Gauge (LGG), were used to measure the strain. The DIC method was used to monitor the displacement and the strain map of the specimen during the test, from which the strain at the center of the specimen can be obtained. The accuracy of the DIC results was assessed, and the displacement and strain uncertainties of our system were 0.003 mm and 0.003, respectively. LGG was used to monitor the expansion of the disc perpendicular to the loading axis, from which the average tensile strain is deduced. The numerical simulation revealed that the tensile strain at the center of the specimen is proportional to the average tensile strain and that the ratio is not sensitive to the material elastic parameters. The strain measured through LGG was compared with that measured by the DIC method using photos captured with a synchronized high-speed camera. The result of the LGG method was 20 % smaller than that of the DIC process. However, the latter was limited by the number of frames of the high-speed camera. The feasibility of this methodology was demonstrated using a polymer-bonded explosive (PBX).     

预静态加载后的混凝土动态受压特性试验

进行了混凝土在应变速率分别为10-5/s、10-4/s、10-3/s的条件下,经历极限抗压强度分别为0、40%、60%、75%和85%的单调荷载作用的动态单轴压缩试验,在此基础上分析了经历不同单调加载历史和应变速率下混凝土的峰值应力、峰值应变和弹性模量的变化规律。试验结果表明,随着应变速率的提高,动态单轴抗压强度明显增加;当单调加载应力水平高于某一应力阈值时,混凝土极限抗压强度明显降低;混凝土弹性模量随着应变速率的提高而增加,随着单调加载幅值的增加表现出先增大后减小的趋势;混凝土峰值应变随着应变速率的提高而增加,随着单调加载幅值的增加而减少。     

中心直裂纹平台巴西圆盘复合型动态应力强度因子

为了指导用中心直裂纹平台巴西圆盘(CSTFBD)试样进行岩石复合型动态断裂 试验，利用有限元法首先验证了文献中对中心直裂纹巴西圆盘(CSTBD)得到的有关结果,分析 比较了不同无量纲裂纹长度(即裂纹半长和圆盘半径之比)时两种圆盘的I, II型动态应力 强度因子的时间历程，发现两者的差异大部分在10{\%}以内，同时验证了该文数值方法的可 靠性. 然后讨论了CSTFBD试样I, II型动态应力强度因子的复合比、起裂角以及纯II型加 载角. 研究成果可为复合型动态断裂试验中CSTFBD试样的加工、试样上应变片的粘贴、起裂 方向和起裂时间的估计等提供参考.     

Erratum to: Rock Dynamic Fracture Toughness Tested with Holed-Cracked Flattened Brazilian Discs Diametrically Impacted by SHPB and its Size Effect

Dynamic fracture initiation toughness of marble was tested using two types of the holed-cracked flattened Brazilian disc (HCFBD) specimens, which were diametrically impacted at the flat end of the disc by the split Hopkinson pressure bar (SHPB) of 100 mm diameter. One type of the discs is geometrically similar with different outside diameter of 42 mm, 80 mm, 122 mm and 155 mm respectively, and with crack length being half the diameter; another type of the discs has identical 80 mm diameter and different crack length. Issues associated with determination of the stress wave loading by the SHPB system and the crack initiation time in the disc specimen were resolved using strain gage technique. The stress waves recorded on the bars and the disc failure patterns are shown and explained. The tested dynamic fracture toughness increases obviously with increasing diameter for the geometrically similar HCFBD specimens. It changes moderately for the one-size specimens of identical diameter and different crack length. The size effect of rock dynamic fracture toughness is mainly caused by the fracture process zone length l and fracture incubation time τ, the latter being an additional influencing factor for the dynamic loading as compared with the counterpart static situation. Hence a method is proposed to determine a unique value for the dynamic fracture initiation toughness, the approach takes average of the local distribution and time history for dynamic stress intensity factor in the spatial-temporal domain, which is defined by l and τ jointly. In this way the dynamic size effect is minimized.     

The Development of a High Rate Tensile Testing System for Micro Scaled Single Crystal Silicon Specimens

Structures have been built at micro scales with unique failure mechanisms that are not yet understood, in particular, under high-rate loading conditions. Consequently, microelectromechanical systems (MEMS) devices can suffer from inconsistent performance and insufficient reliability. This research aims to understand the failure mechanisms in micro-scaled specimens deforming at high rates. Single-crystal silicon (SCS) micro specimens that are 4 μm thick are subjected to tensile loading at an average strain rate of 92 s^?1 using a miniature Hopkinson tension bar. A capacitance displacement system and piezoelectric load cell are incorporated to directly measure the strain and stress of the silicon micro specimens. The average dynamic elastic modulus of the silicon micro specimens is measured to be 226.8?±?18.50 GPa and the average dynamic tensile strength of the silicon is measured to be 1.26?±?0.310 GPa. High-speed images show that extensive fragmentation of the specimens occurs during tensile failure.