均衡型层合板

本文在经典层合板理论的基础上讨论了层合板的均衡型问题.给出了既适合阿络理论也适合层合板理论的广义均衡型条件;阐明了均衡型的力学机理.均衡型是使层合板面内各方向具有相同相对伸长时的铺层形式.说明了均衡型层合板的应变和应力计算方法.引入均衡应变概念,讨论了与金属层复合时层合板的均衡型,并用表格形式开列了网络理论的相应公式.本文的结果不仅适合同种纤维增强的层合板,也适合不同种纤维增强的混杂层合板.     

含脱层层合板分叉屈曲的宏微观失效机制分析

根据板壳理论并考虑层合板脱层处的接触效应影响,推导了层合板的控制方程,借助量纲归一化分析建立了该问题的八次特征方程。通过对特征方程各参数进行定性分析,建立了求解八次方程根的解析表达式,发现了层合板的宏微观变形模态。利用MATLAB软件进行算例分析,获得了在不同脱层情况下层合板的屈曲模态参数和临界屈曲荷载。研究表明:层合板的屈曲模态包含整体一致的宏观变形和界面处的微观变形。研究结果与ABAQUS的有限元解进行了对比,结果表明:理论解与有限元分析的结果非常一致。论文从理论分析的角度研究了复合材料矩形层合板的屈曲问题,从理论上剖析了分层层合板的宏微观失效模态。     

基于新修正偶应力理论的Mindlin层合板稳定性分析

基于新的各向异性修正偶应力理论提出一个Mindlin复合材料层合板稳定性模型。该理论包含纤维和基体两个不同的材料长度尺度参数。不同于忽略横向剪切应力的修正偶应力Kirchhoff薄板理论,Mindlin层合板考虑横向剪切变形引入两个转角变量。进一步建立了只含一个材料细观参数的偶应力Mindlin层合板工程理论的稳定性模型。计算了正交铺设简支方板Mindlin层合板的临界载荷。计算结果表明该模型可以用于分析细观尺度层合板稳定性的尺寸效应。     

非对称铺层复合材料层合板质量优化设计

复合材料广泛应用于航空航天等领域,追求轻量化设计已经成为研究重点。对复合材料层合板质量优化设计,可以减少层合板的纤维用量,减小层合板的质量,降低成本。首先研究复合材料层合板在承受轴向载荷时,产生的形变量、应力示意图,分析容易发生失效部位;以层合板铺层厚度为设计变量,最大应变、铺层比例等为约束条件,最小化层合板质量为优化目标,对碳纤维复合材料层合板铺层厚度等设计变量进行优化,利用强度理论对优化结果进行校核,结合力学试验对比分析优化前后层合板力学性能。结果表明:碳纤维复合材料层合板经过优化后,总质量减轻约16.7%,优化后的层合板满足复合材料强度理论,实验结果与软件仿真具有一致性,说明优化方法是合理可靠的。     

中间弱层对层合板性能影响分析

对于夹胶玻璃等结构,由于中间胶层很弱,层合板结构的层间剪切效应占主导地位。此时经典层合板理论以及整体高阶剪切位移场理论所预测的结果可能导致很大的实际误差,应采用更加精细的力学模型来分析弱层的效应。本文建立了分层位移场假设下的浅柱面层合板静力计算模型以及自振周期计算模型,并同经典层合板理论计算结果对比,分析了中间层的剪切模量、弹性模量、层合板曲率半径对层间剪切效应的影响。计算结果表明:中间层的剪切模量对层合板的受力性能有着决定性的影响,相对来说中间层的弹性模量对层合板性能的影响不太显著;当中间层与面层的剪切模量比值小于0.2时,随着中间层剪切模量的减小,两个模型的计算误差急剧增大。     

薄膜-基体型磁致伸缩微致动器的数值模拟

磁致伸缩薄膜是一种性能优异的微驱动元件。本文针对磁致伸缩薄膜一基体结构中薄膜磁致伸缩系数与层合结构变形之间关系的问题，从经典层合板理论的角度导出了其基本方程，并在此基础上对基体远厚于薄膜的情形采用非层合板理论进行了简化。通过比较非层合板理论和层合板理论下的薄膜一基体结构变形的有限元结果，讨论了有关几何参数和物理参数的影响，给出了用非层合板理论近似处理薄膜一基体型磁致伸缩微致动器的适用条件。     

复合材料层合板的颤振特性及振动抑制研究

研究了超声速流中压电复合材料层合板的颤振特性及振动抑制方法。采用一阶活塞理论计算了超声速流场中的气动压力,基于经典层合板理论和Hamilton原理推导了压电复合材料层合板的动力学模型,设计了滑模观测器以减少观测溢出,通过Lyapunov方法证明观测器的稳定性,应用观测状态设计了LQR控制器,讨论了几何参数、铺设角度对压电复合材料层合板颤振特性的影响,利用SIMULINK仿真求解了层合板的脉冲响应,验证了控制器的有效性。结果表明,合理规划层合板的几何参数和铺设角度可提高系统颤振稳定性,滑模观测器能够较为准确地追踪原始系统且具有良好的鲁棒性,LQR控制可以在一定范围内消除层合板的颤振点,并且能够有效地控制压电复合材料层合板在颤振边界处的振动,Q矩阵越大,振动控制效果越好,压电层厚度越大,LQR控制效果越好。     

双模量面板泡沫铝芯圆形层合板的非线性弯曲

双模量材料是典型的拉压弹性模量不同的材料,在均匀外载荷作用下,双模量面板泡沫铝芯圆形层合板相当于三种不同材料组成的层合板。采用弹性理论建立了双模量面板泡沫铝芯圆形层合板在均布载荷作用下的静力平衡方程,利用该静力平衡方程确定了层合板的中性面位置。在此基础上建立了双模量面板泡沫铝芯圆形层合板的大挠度弯曲微分方程组,求得了层合板中心挠度与均布载荷的关系式。该方法计算结果与有限元计算结果的最大误差仅为3.8%,这说明该方法是可靠的。算例分析表明不考虑面板拉压弹性模量相异时其计算结果与实际情况相差较大,超过了工程上所允许的计算误差5%。所以,在计算双模量面板泡沫铝芯圆形层合板的非线性弯曲时,不宜采用相同弹性模量弹性理论,而应该采用拉压弹性模量不同的弹性理论。     

基于精化高阶理论的层合板热-力问题有限元分析

基于精化高阶理论,建立了层合板有限元模型,编制了相应的MATLAB 程序．分析了三层四边简支层合板在力荷载作用下的响应,与解析解吻合良好．分析了热-力共同作用下层合板的响应,与基于ABAQUS 软件建立的精细有限元模型计算结果相对比,验证了模型的高效性．研究了跨厚比和铺设方式对层合板层间应力的影响,结果表明：跨厚比对层间应力影响显著,两者之间大致呈反比例函数关系;对称铺设方式可以有效降低层合板中的层间应力．     

具有分层损伤的不同加筋形式复合材料层合板的后屈曲性态研究

基于板的一阶剪切理论和V on-K arm an大挠度理论,分别推导了复合材料层合板和层合梁的几何非线性有限元列式,提出了含嵌入分层的复合材料加筋层合板在受压缩载荷作用下的后屈曲有限元分析方法,对在板厚方向具有不同分层位置的加筋板结构进行了有限元数值分析,研究了不同的加筋方式及筋的分布对具有分层损伤的复合材料加筋层合板的后屈曲性态的影响,所得结果对确定在压缩载荷作用下含损伤复合材料加筋层合板的剩余承载能力具有参考价值。     

On the refined first-order shear deformation plate theory of Kármán type

A new refined first-order shear-deformation plate theory of the Kármán type is presented for engineering applications and a new version of the generalized Kármán large deflection equations with deflection and stress functions as two unknown variables is formulated for nonlinear analysis of shear-deformable plates of composite material and construction, based on the Mindlin/Reissner theory. In this refined plate theory two rotations that are constrained out in the formulation are imposed upon overall displacements of the plates in an implicit role. Linear and nonlinear investigations may be made by the engineering theory to a class of shear-deformation plates such as moderately thick composite plates, orthotropic sandwich plates, densely stiffened plates, and laminated shear-deformable plates. Reduced forms of the generalized Kármán equations are derived consequently, which are found identical to those existe in the literature. Foundation item: the National Natural Science Foundation of China (59675027) Biography: Zhang Jianwu (1954-)     

基于高阶剪切变形理论的四边形求积元板单元及其应用

近年来由各类新型复合材料或功能梯度材料构成的板结构在工程领域得到了广泛应用,其显著特点是材料性能沿板厚变化.为合理考虑横向剪切应变,许多学者基于Reddy高阶剪切变形理论,构建了不同的有限元单元对该类板结构进行分析,但其中满足$C^{1}$连续条件的单元相对较少.本文基于Reddy高阶剪切变形理论,采用求积元方法,建立了$C^{1}$连续的四边形板单元.利用该单元对均质材料、复合材料、功能梯度材料构成的等厚度矩形板、变厚度矩形板及等厚度斜板的线弹性弯曲和自由振动问题进行了计算分析,并与现有文献中的相应计算结果进行了对比.研究表明:基于高阶剪切变形理论的四边形求积元板单元具有较高的计算效率和良好的适应性,文中各类材料构成的等变厚度矩形板及等厚度斜板均只需1个单元即可得到理想的计算结果.对于等/变厚度矩形板,可仅使用9$\times$9个积分点,而对于等厚度斜板,随着斜角的增大,所需积分点的数目逐渐增多至15$\times $15.该四边形求积元板单元可进一步用于新型复合材料板的非线性分析.      

Theoretical and experimental studies on nonlinear oscillations of symmetric cross-ply composite laminated plates

The nonlinear oscillations and resonant responses of the symmetric cross-ply composite laminated plates are investigated theoretically and experimentally. The governing equations of motion for the composite laminated plate are derived by using the von Karman type equation, Reddy’s third-order shear deformation plate theory, and Galerkin method with the geometric nonlinearity. The four-dimensional averaged equation is obtained by using the method of multiple scales. The frequency-response functions are analyzed under the consideration of strongly coupled of two modes. The influences of the resonance case on the softening and hardening type of nonlinearity are analyzed with different parameters for the composite laminated plates. The numerical results indicate that there exist the hardening and softening types of the composite laminated plate in the specific resonant case. The variation of the response amplitudes is studied for the composite laminated plate under combined the transverse and in-plane excitations. A sweep frequency experiment is performed to obtain the hardening and softening nonlinearities of a composite laminated plate. The experimental results coincide with the numerical results qualitatively. The influences of the excitation amplitudes on the softening and hardening types of nonlinearity are also analyzed for the composite laminated plate. The amplitude spectrums of the test plate also demonstrate that the change of the nonlinear dynamic responses may be caused by the subharmonic resonance.     

Thin plate spline radial basis functions for vibration analysis of clamped laminated composite plates

A meshless method based on thin plate spline radial basis functions and higher-order shear deformation theory are presented to analyze the free vibration of clamped laminated composite plates. The singularity of thin plate spline radial basis functions is eliminated by adding infinitesimal to the zero distance. Convergence characteristics of the present thin plate spline radial basis functions for the vibration analysis of the clamped laminated plates are investigated. The frequencies computed by the present method agree well with the available published results.     

BENDING RESPONSES OF AN EXPONENTIALLY GRADED SIMPLY-SUPPORTED ELASTIC/VISCOELASTIC/ELASTIC SANDWICH PLATE

The bending response for exponentially graded composite (EGC) sandwich plates is investigated.The three-layer elastic/viscoelastic/elastic sandwich plate is studied by using the sinusoidal shear deformation plate theory as well as other familiar theories.Four types of sandwich plates are considered taking into account the symmetry of the plate and the thickness of each layer.The effective moduli and Illyushin’s approximation methods are used to solve the equations governing the bending of simply-supported EGC fiber-reinforced viscoelastic sandwich plates.Then numerical results for deflections and stresses are presented and the effects due to time parameter,aspect ratio,side-to-thickness ratio and constitutive parameter are investigated.     

A refined finite element method for bending analysis of laminated plates integrated with piezoelectric fiber-reinforced composite actuators

This research presents a finite element formulation based on four-variable refined plate theory for bending analysis of cross-ply and angle-ply laminated composite plates integrated with a piezoelectric fiber-reinforced composite actuator under electromechanical loading. The four-variable refined plate theory is a simple and efficient higher-order shear deformation theory, which predicts parabolic variation of transverse shear stresses across the plate thickness and satisfies zero traction conditions on the plate free surfaces. The weak form of governing equations is derived using the principle of minimum potential energy, and a 4-node non-conforming rectangular plate element with 8 degrees of freedom per node is introduced for discretizing the domain. Several benchmark problems are solved by the developed MATLAB code and the obtained results are compared with those from exact and other numerical solutions, showing good agreement.     

弹性力学状态变量体系下带有初应力的振动问题

通过在Hellinger-Reissner广义势能中引入应变的非线性项,推导出了弹性力学Hamilton体系下的具有初应力的振动方程,并运用精细积分给出了两端简支的梁、组合梁和四边简支板及组合板在初应力下振动频率。本文结果是严格弹性力学意义(没有引入任何几何变形假设)下的精确解,为衡量各种计入剪切变形的薄板、中厚板理论的准确性提供了一个标准。     

板结构计算模型的新发展

现代复合材料层合板具有高强和轻型的突出优点，从而在军工和民用等诸多领域发挥着重要作用。这种板结构的特点是随着纤维走向的不同，层间材料的物理-力学特性发生剧烈变化。沿板厚方向变形的梯度比较陡峭，并在层间结合面处发生强不连续，呈现zig-zag （锯齿状）现象。这导致横向剪应变在板的静态和动态响应中发生重要作用，不计横向变形的经典组合板计算模型CLPT难以适应现代多层板计算分析的需要。考虑横向剪切变形影响的板的计算模型得到重视和发展。需要指出，现有各种考虑剪切变形影响的计算模型虽然有了很大的发展，但在全面和准确性上仍然存在一定的不足，难以适应现代多层组合板横向力和物理性能多变的情况。模型预测的沿板厚方向位移和应力的变化规律难以通过严格的检验。本文提出的以比例边界有限元为基础的正交各向异性板的数值计算模型，同时可适用于各种薄板与厚板的分析，对现代复合材料层合板的分析具有特殊的优越性。所得到的板的位移、正应力和剪应力沿板厚方向的变化，与三维弹性理论的标准解高度吻合。数值算例进一步表明，随着层间纤维走向的变化，板内位移场和应力场沿板厚方向剧烈变化所呈现的锯齿现象均可以精准地进行模拟。据此，本文建议方法对现代板分析的广泛适应性和高度准确性得到了充分论证。     

Large deflection analysis of unsymmetrically laminated composite plates: analytical-numerical type approach

Large deflection analysis of laminated composite plates is considered. The Galerkin method along with Newton-Raphson method is applied to large deflection analysis of laminated composite plates with various edge conditions. The von Kármán plate theory is utilized and the governing differential equations are solved by choosing suitable polynomials as trial functions to approximate the plate displacement functions. The solutions are compared to that of Dynamic Relaxation and finite elements. A very close agreement has been observed with these approximating methods. In the solution process, analytical computation has been done wherever it is possible, and analytical-numerical type approach has been made for all problems.     

Nonlinear transient response of strain rate dependent composite laminated plates using multiscale simulation

The effects of strain rate dependency and inelasticity on the transient responses of composite laminated plates are investigated. A micromechanics model which accounts for the transverse shear stress effect, the effect of strain rate dependency and the effect of inelasticity is used for analyzing the mechanical responses of the fiber and matrix constituents. The accuracy of the micromechanics model under transverse shear loading is verified by comparing the results with those obtained using a general purpose finite element code. A higher order laminated plate theory is extended to capture the inelastic deformations of the composite plate and is implemented using the finite element technique. A complete micro–macro numerical procedure is developed to model the strain rate dependent behavior of inelastic composite laminates by implementing the micromechanics model into the finite element model. Parametric studies of the transient responses of composite plates are conduced. The effects of geometry, ply stacking sequence, material models, boundary conditions and loadings are investigated. The results show that the strain rate dependency and inelasticity influence the transient responses of composite plates via two significantly different mechanisms.