Natural convection boiling of water and surfactant solutions having negligible environmental impact in vertical confined space

Natural convection boiling of water and surfactant solutions in a confined space between two vertical plates was studied experimentally in the range of heat flux 19–170 kW/m². The surfactant used was Alkyl (8–16) Glucoside having negligible environmental impact. The gap size was changed in the range of s = 1–80 mm, the concentration of surfactant solutions was changed in the range of C = 200–600 ppm. Generally, an addition of surfactant leads to an enhancement of heat transfer compared to water boiling at the same gap size. Enhancement of the heat transfer depending on the solution concentration at fixed gap size yields maximum value at the solution concentration close to the critical micelle concentration. The effect of confined space on a bubble dynamic was studied. Temperature field on the heater was determined using the infrared thermography technique. Quasi periodic wall temperature fluctuations were observed in the regime of high heat flux. An increase in the Bond number leads to an increase in the dimensionless frequency of the heated wall temperature fluctuations. The correlation between the dimensionless parameter of heat transfer and the Bond number under condition of quasi periodic boiling was derived and discussed.     

Effect of surfactant concentration on saturated flow boiling in vertical narrow annular channels

Saturated flow boiling of environmentally acceptable nonionic surfactant solutions of Alkyl (8–16) was compared to that of pure water. The concentration of surfactant solutions was in the range of 100–1000 ppm. The liquid flowed in an annular gap of 2.5 and 4.4 mm between two vertical tubes. The heat was transferred from the inner heated tube to two-phase flow in the range of mass flux from 5 to 18 kg/m² s and heat flux from 40 to 200 kW/m². Boiling curves of water were found to be heat flux and channel gap size dependent but essentially mass flux independent. An addition of surfactant to the water produced a large number of bubbles of small diameter, which, at high heat fluxes, tend to cover the entire heater surface with a vapor blanket. It was found that the heat transfer increased at low values of relative surfactant concentration C/C₀, reaches a maximum close to the value of C/C₀ = 1 (where C₀ = 300 ppm is the critical micelle concentration) and decreased with further increase in the amount of additive. The dependence of the maximal values of the relative heat transfer enhancement, obtained at the value of relative concentration of C/C₀ = 1, on the boiling number Bo may be presented as single curve for both gap sizes and the whole range of considered concentrations.     

Nucleate boiling and critical heat flux of HFE-7100 in horizontal narrow spaces

The pool boiling heat transfer and critical heat flux CHF of saturated HFE-7100 at atmospheric pressure on a confined smooth copper surface were experimentally studied. The horizontal upward boiling surface was confined by a face-to-face parallel unheated surface. We analysed the effects obtained by changing the diameter of the unheated surface and the gap between the boiling surface and the adiabatic surface. The gap values investigated were s = 0.5, 1.0, 2.0, 3.5 mm. To confine the circular boiling surface (d = 30 mm), two different Plexiglas discs were used: one with a diameter D = 30 mm, equal to that of the copper boiling surface, and the other with a diameter D = 60 mm, equal to that of the overall test section support. For each configuration, boiling curves were obtained up to the thermal crisis. For both configurations, it was observed that, at low wall superheat, the effect of confinement was not significant if Bo > 1, while for Bo ? 1 the heat transfer coefficient increased as the channel width s decreased. By contrast, at high wall superheat, a drastic reduction in both heat transfer and CHF was seen when the channel width s decreased; this reduction was less pronounced when the smaller confinement disc (D = 30 mm) was used. CHF data were also compared with the values predicted by literature correlations.     

Motion of singles bubbles moving under a slightly inclined surface through stationary liquids

The influence of the liquid properties on the dynamical bubble shape and on the bubble motion has been investigated for bubbles moving under a downward facing inclined surface. The Morton number Mo varied from 2.59 × 10⁻¹¹ to 2.52 × 10⁺⁰¹. The Bond number Bo covered the range from 10 to 150 and the surface inclination angle θ was varied from 2° to 6°. To cover the wide range of Mo, several liquids such as glycerine, propanediol, water and isopropanol were used. The results have shown that the relation Fr = Fr(Bo, Mo, θ) is not adequate to describe the bubble motion, where Fr is the terminal Froude number. The choice of the terminal Reynolds number Re as the dependent parameter, allowed the clarification of the role of the Morton number on the bubble motion. At a given Bond number, the bubble Reynolds number decreases monotonously with the Morton number. Furthermore, an empirical correlation Re = Re(Bo, Mo, θ) is given that can be readily used in the mathematical modelling of bubble laden flows under solids.     

Effect of surfactant additives on nucleate pool boiling heat transfer of refrigerant-based nanofluid

Effect of surfactant additives on nucleate pool boiling heat transfer of refrigerant-based nanofluid was investigated experimentally. Three types of surfactants including Sodium Dodecyl Sulfate (SDS), Cetyltrimethyl Ammonium Bromide (CTAB) and Sorbitan Monooleate (Span-80) were used in the experiments. The refrigerant-based nanofluid was formed from Cu nanoparticles and refrigerant R113. The test surface is horizontal with the average roughness of 1.6 μm. Test conditions include a saturation pressure of 101.3 kPa, heat fluxes from 10 to 80 kW m⁻², surfactant concentrations from 0 to 5000 ppm (parts per million by weight), and nanoparticle concentrations from 0 to 1.0 wt.%. The experimental results indicate that the presence of surfactant enhances the nucleate pool boiling heat transfer of refrigerant-based nanofluid on most conditions, but deteriorates the nucleate pool boiling heat transfer at high surfactant concentrations. The ratio of nucleate pool boiling heat transfer coefficient of refrigerant-based nanofluid with surfactant to that without surfactant (defined as surfactant enhancement ratio, SER) are in the ranges of 1.12-1.67, 0.94-1.39, and 0.85-1.29 for SDS, CTAB and Span-80, respectively, and the values of SER are in the order of SDS > CTAB > Span-80, which is opposite to the order of surfactant density values. The SER increases with the increase of surfactant concentration and then decreases, presenting the maximum values at 2000, 500 and 1000 ppm for SDS, CTAB and Span-80, respectively. At a fixed surfactant concentration, the SER increases with the decrease of nanoparticle concentration. A nucleate pool boiling heat transfer correlation for refrigerant-based nanofluid with surfactant is proposed, and it agrees with 92% of the experimental data within a deviation of ±25%.     

Macro-to-microchannel transition in two-phase flow: Part 2 - Flow boiling heat transfer and critical heat flux

This part of the paper presents the current experimental flow boiling heat transfer and CHF data acquired for R134a, R236fa and R245fa in single, horizontal channels of 1.03, 2.20 and 3.04 mm diameters over a range of experimental conditions. The aim of this study is to investigate the effects of channel confinement, heat flux, flow pattern, saturation temperature, subcooling and working fluid properties on the two-phase heat transfer and CHF. Experimentally, it was observed that the flow boiling heat transfer coefficients are a significant function of the type of two-phase flow pattern. Furthermore, the monotonically increasing heat transfer coefficients at higher vapor qualities, corresponding to annular flow, signifies convective boiling as the dominant heat transfer mechanism in these small scale channels. The decreasing heat transfer trend at low vapor qualities in the slug flow (coalescing bubble dominated regime) was indicative of thin film evaporation with intermittent dry patch formation and rewetting at these conditions. The coalescing bubble flow heat transfer data were well predicted by the three-zone model when setting the dryout thickness to the measured surface roughness, indicating for the first time a roughness effect on the flow boiling heat transfer coefficient in this regime. The CHF data acquired during the experimental campaign indicated the influence of saturation temperature, mass velocity, channel confinement and fluid properties on CHF but no influence of inlet subcooling for the conditions tested. When globally comparing the CHF values for R134a in the 0.51-3.04 mm diameter channels, a peak in CHF peak was observed lying in between the 0.79 (Co ≈ 0.99) and 1.03 (Co ≈ 0.78) mm channels. A new CHF correlation has been proposed involving the confinement number, Co that is able to predict CHF for R134a, R236fa and R245fa in single-circular channels, rectangular multichannels and split flow rectangular multichannels. In summary, the present flow boiling and CHF trends point to a macro-to-microscale transition as indicated by the results presented in Ong and Thome (2011) [1].     

Carbon dioxide flow boiling in a single microchannel - Part II: Heat transfer

Flow boiling heat transfer coefficients of CO₂ have been measured in a single microchannel. Experiments were carried out in a horizontal stainless steel tube of 0.529 mm inner diameter, for three temperatures (−10, −5 and 0 °C), with the mass flux ranging from 200 to 1200 kg/m² s and the heat flux varying from 10 to 30 kW/m². The investigation covered qualities from zero to the dryout inception, i.e. pre-dryout conditions. Compared to larger microchannels and positive temperatures, a higher contribution of convective boiling was found, with a larger heat transfer coefficient than for pure nucleate boiling. Mainly two heat transfer regimes were found, depending on the boiling number (Bo). For Bo > 1.1 × 10⁻⁴, the heat transfer coefficient was highly dependent on the heat flux and moderately influenced by the quality and the mass flux. For Bo < 1.1 × 10⁻⁴, the heat transfer coefficient was hardly affected by the heat flux but strongly influenced by the quality and the mass flux. In addition, dryout results were reported. The effect of the mass flux on the dryout inception quality was found to be highly dependent on the heat flux and the saturation temperature.     

Subcooled pool boiling of water on a downward-facing stainless steel disk in a gap

Pool boiling is experimentally studied on a relatively large downward-facing surface with heated stainless steel disk diameters of D = 100 and 300 mm in confined space at atmospheric pressure using water as the working fluid. The bulk working fluid is subcooled. The gap size s can be adjusted to 10, 15 and 20 mm for D = 100 mm and 0.9–77 mm for D = 300 mm. We found that pool boiling under the present condition is far weaker than that occurring on an upward-facing surface. Furthermore, we found that the larger the diameter of the stainless steel plate, the weaker the pool boiling heat transfer. The heat transfer rate may be predicted by the Kutateladze correlation for s > 20 mm and by its modified form for s < 20 mm for both D = 100 and D = 300 mm. Two different typical bubble circulation motions are found. Type I motion occurs with a probability of 90.9% and type II occurs with a probability of 9.1% according to the statistical calculations. Most coalesced bubble diameters are from 90 to 100 mm for D = 100 mm and from 100 to 200 mm for D = 300 mm.     

Pool boiling heat transfer of ultra-light copper foam with open cells

High speed visualizations and thermal performance studies of pool boiling heat transfer on copper foam covers were performed at atmospheric pressure, with the heating surface area of 12.0 mm by 12.0 mm, using acetone as the working fluid. The foam covers have ppi (pores per inch) from 30 to 90, cover thickness from 2.0 to 5.0 mm, and porosity of 0.88 and 0.95. The surface superheats are from −20 to 190 K, and the heat fluxes reach 140 W/cm². The 30 and 60 ppi foam covers show the periodic single bubble generation and departure pattern at low surface superheats. With continuous increases in surface superheats, they show the periodic bubble coalescence and/or re-coalescence pattern. Cage bubbles were observed to be those with liquid filled inside and vented to the pool liquid. For the 90 ppi foam covers, the bubble coalescence takes place at low surface superheats. At moderate or large surface superheats, vapor fragments continuously escape to the pool liquid.     

Enhanced nucleate boiling on copper micro-porous surfaces

Saturation boiling of PF-5060 dielectric liquid on Cu micro-porous surface layers (95, 139, 171, 197 and 220-μm thick) is investigated. These layers are deposited on 10 × 10 mm Cu substrates using two-stage electrochemical process. The basic micro-structure, obtained in the first stage using current density of 3 A/cm² for 15–44 s, depending on thickness, is strengthened by continuing electrochemical deposition using much lower current density for 10’s of minutes. For conditioned surface layers, after a few successive boiling tests, the pool boiling curves are reproducible and the temperature excursion prior to boiling incipience is either eliminated or reduced <7 K. Present nucleate boiling results are markedly better than those reported for dielectric liquids on micro- and macro-structured surfaces. Present values of CHF (22.7–27.8 W/cm²) and h_MNB (2.05–13.5 W/cm² K) are ∼40–70% higher than and >17 times those reported on plane surfaces (<16 W/cm² and ∼0.8 W/cm² K). Best results are those of the 171-μm thick layer: CHF of 27.8 W/cm² occurs at ΔT_sat of only 2.1 K and h_MNB of 13.5 W/cm² K occurs at ΔT_sat = 2.0 K.