首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
溶胶-凝胶法制备的ZrO_2薄膜的摩擦学性能研究   总被引:1,自引:0,他引:1  
在 Si(10 0 )基片上制备晶态 Zr O2 薄膜 ,考察了薄膜的摩擦学性能和摩擦磨损机制 .结果表明 :在低负荷 (0 .5 N )下 ,Zr O2 薄膜与 GCr15钢球和 Si3N4陶瓷球对摩时具有优良的抗磨减摩性能 ,在滑动 5 0 0 0次时的摩擦系数分别为0 .14和 0 .13;但随着负荷和滑动速度的增大 ,薄膜的耐磨寿命降低 ,摩擦系数增大 .采用扫描电子显微镜对薄膜磨痕表面形貌进行观察分析 ,发现在较低负荷和滑动速度条件下 ,Zr O2 薄膜的磨损机制为轻微擦伤 ;而在相对较高的负荷和滑动速度条件下 ,其磨痕表面呈现塑性变形 ,严重擦伤和断裂剥落特征  相似文献   

2.
溶胶—凝胶法制备的ZrO2薄膜的摩擦学性能研究   总被引:7,自引:3,他引:4  
在Si(100)基片上制备晶态ZrO2薄膜,考察了薄膜的摩擦学性能和摩擦磨损机制。结果表明:在低负荷(0.5N)下,ZrO2薄膜与GCr15钢球和Si3N4陶瓷球对摩时具有优良的抗磨减摩性能,在滑动5000次时的摩擦系数分别为0.14和0.13;但随着负荷和滑动速度的增大,薄膜的耐磨寿命降低,摩擦系数增大。采用扫描电子显微镜对薄膜磨痕表面形貌进行观察分析,发现在较低负荷和滑动速度条件下,ZrO2薄膜的磨损机制为轻微擦伤;而在相对较高的负荷和滑动速度条件下,其磨痕表面呈现塑性变形,严重擦伤和断裂剥落特征。  相似文献   

3.
采用纯铁圆盘试样与标准碳钢钢球(45钢)组成球-盘摩擦副进行旋转摩擦试验,研究在干摩擦条件下,不同的滑动速度及法向载荷下摩擦表面的磁记忆现象.试验结果表明:磨损前后磁记忆信号存在较大差异,磨损后的磁记忆信号在磨痕处出现信号突变,此突变信号可以准确地表征磨痕的位置及磨痕的宽度.对磁记忆信号进行梯度处理,可以发现不同工况下磨痕处的信号峰面积S、交点距n及梯度峰峰值Vpp三者均不相同,且与磨痕的特征存在一定的关系.此外,通过获取不同干摩擦条件下磨痕处的梯度信号特征值,发现信号峰面积S、交点距n及梯度峰峰值Vpp三者均随滑动速度及法向载荷的增大而增大.  相似文献   

4.
车轮钢滚动剥离摩擦磨损特性研究   总被引:7,自引:1,他引:6  
在NENE-2型摩擦磨损试验机上利用往复滚动试验装置研究了不同滚滑状态下车轮钢的剥离摩擦磨损特性和碳含量对车轮钢滚动剥离磨损性能的影响.结果表明:在不同滚滑状态下摩擦副之间的摩擦力不同,平面试样的表面磨痕形貌随着不同的切向摩擦力而明显不同,随着切向摩擦力的增大滚动磨损机制亦发生改变,剥离磨损加剧且磨损深度变大,当相对滑动量增大到一定程度后,磨损表现为明显的剥层机制;碳含量对车轮钢的滚动磨损表面磨痕形貌影响显著,碳含量低时磨痕以犁沟为主,碳含量高时剥离磨损发生的概率增加.  相似文献   

5.
分别采用正火和调质工艺对新型破冰船用低碳高强钢进行了热处理,并使用UMT-3多功能摩擦磨损试验机低温模块和摩擦电化学模块研究了其在低温模拟海水环境中不同外加电位下的磨损-腐蚀耦合行为. 使用电子扫描显微镜和白光干涉显微镜对钢样的微观组织及磨痕形貌进行了表征,并对其在不同外加电位作用下的磨损-腐蚀机理进行了探讨. 结果表明:两种热处理后的钢材的平均摩擦系数都随外加电位升高而降低,而磨痕深度、磨损量和腐蚀电流则随着外加电位升高而增加;钢材的开路电位随着磨损的发生逐渐负移,腐蚀电流密度增加;其中,经过正火处理的钢样磨痕表面主要出现剥落坑,而调质钢磨痕表面则主要出现了裂纹和腐蚀坑. 正火钢磨损和腐蚀损失量所占比例分别为80.6%、19.4%,调质钢分别为55.1%、44.9%,两种钢材的磨损-腐蚀之间相互促进损失量ΔVW和ΔVC均为正值,证实磨损和腐蚀之间存在着相互协同作用.   相似文献   

6.
在新型冲击磨损试验机上,以TC4钛合金作为研究对象开展了在硬质沙粒条件下的冲击试验.考察了沙粒粒径(120~380μm)、冲击次数对TC4钛合金冲击磨损行为的影响.研究结果表明:粒径能显著影响TC4钛合金的冲击磨损行为.在冲击过程中硬质沙粒会不断切削、挤压试样表面,造成较大的材料损失.随着沙粒粒径的增加,磨损面积增加,冲击力峰值、磨损深度和界面的能量吸收率都呈现先增加后减小的趋势.随着冲击次数的增加,冲击力峰值和界面能量吸收率增加,磨损加剧.硬质沙粒冲击作用下TC4钛合金的磨损机制主要表现为沙粒棱角对试样表面的微观切削和挤压剥落.  相似文献   

7.
在自制的新型试验机上,以纯铁为考察对象开展了球/平面接触模式下的冲击微动磨损试验.在改变冲击能量、冲击质量的情况下,研究了材料的冲击力学响应和磨损机制.结果表明:在增大冲击能量的条件下,试样受到的冲击力和能量吸收率相应增加,磨损体积、磨损率也随之提高.冲击动能相同时,增大冲击质量(降低冲击速度),冲击力峰值和能量吸收率进一步提高,磨损程度减轻.纯铁的冲击磨损机制主要表现为剥层磨损,且磨痕区域发生了氧化行为,越靠近边缘,氧化程度越高.  相似文献   

8.
氮气气氛条件下钢/铜摩擦副的摩擦磨损特性研究   总被引:1,自引:1,他引:0  
利用MMS-1G型销-盘式高温高速摩擦磨损试验机研究了氮气气氛条件下CrNiMo钢/H96黄铜配副的摩擦磨损特性,利用扫描电子显微镜观察磨损表面形貌,采用能谱仪分析磨损表面及其磨屑的主要元素成分,并分析其磨损机理.结果表明:在氮气气氛条件下,摩擦系数随滑动速度和载荷(pv值)增加而减小;磨损率随pv值增加而增大;在逐步增加pv值的过程中,其磨损机制由粘着磨损转变为磨粒磨损和粘着磨损共同作用.  相似文献   

9.
摩擦磨损的扫描电子显微镜原位动态研究,可以跟踪观察磨屑形成和磨痕演变的全过程,以及材料表面在摩擦磨损中变化的真实情况.在由国产台式扫描电子显微镜改装成的滑动摩擦磨损试验装置上,对15#钢-45#钢摩擦磨损过程所作的原位动态研究表明:15#钢在对摩过程中始终存在粘-滑现象,微切削是其主要磨损机理;15#钢磨痕形貌变化可分5个阶段——第1阶段出现与滑动方向垂直的横向裂纹,第2阶段产生大片状剥离,第3阶段产生小片状疲劳剥离,第4阶段产生块状磨屑并形成表面凹坑,第5阶段磨痕趋于平坦.这种滑动摩擦磨损试验装置不仅具有对摩擦磨损过程作动态跟踪观察的功能,而且可用于对摩擦学过程作准动态观察,这两种观察方法对研究摩擦磨损过程同等重要  相似文献   

10.
采用316L不锈钢材质的锐角圆锥块作为摩擦对偶,在硼酸锂的液流条件下对2种Zr(-Sn)-Nb合金管进行不同循环次数(N=102,103,104,105,106)的冲击试验.模拟了锆合金包壳在异物磨蚀情况下的冲击状态,研究了2种Zr(-Sn)-Nb合金管的冲击磨损性能及冲击磨损机制.结果表明,锆合金管材在冲击磨损作用下的磨损机制主要为塑性变形和疲劳剥落.机械性能、动力学曲线和冲击磨损试验等数据皆表明,Zr-Sn-Nb合金拥有比Zr-Nb合金更好的抵抗316L不锈钢冲击磨损的能力.磨痕边缘材料塑性流动导致的裂纹形成与扩展及磨痕底部裂纹延伸交汇后发生的疲劳剥落,都会对锆合金管造成严重的磨损去除.冲击过程中,锆合金管与摩擦对偶会发生材料迁移,形成Zr、O、C、Fe元素不均匀分布的磨屑堆积层.  相似文献   

11.
韩文娟  刘海 《力学与实践》2010,32(4):109-111
对《力学》中的物体自由度进行多方面分析,以深化教学、提高学生正 确分析物理问题的能力.使用实际教学分析的研究方法,在《力学》范围内讨论自由度与坐标、 自由与约束的关系并得以下结论: (1) 同一物体的自由度随其所在的``空间'不同而不同, 不因坐标系的选取不同而 异, 在同类参考系中不因参考系的动静而有别;(2)自由度遵循叠加原理. 讨论了质点系的总自由度及相关计算问题,并指出研究《力学》中自由度的意义.  相似文献   

12.
The present paper deals with development and design of new methods utilizing Wiedemann's effect for determination of state of strain in building structures. Wiedemann's effect and some features of torsional strain of magnetic field are the basis of new experimental method. Especially the point electromagnetic strain gages using the effect of pure torsion of electromagnetic field to enable universal examination. For strain-gage measurements, almost all physical quantities are used which can be related to the variation in length of the structures. From the electric strain measurements, the most commonly used methods are the measurements by resonance-wire strain gages or by electric-resistance strain gages. In this paper, electromagnetic strain gages are discussed using the Wiedemann effect, and the author describes some new measuring equipment and his own suggestions and methods based on an application of this effect.  相似文献   

13.
14.
15.
16.
It is well known that the problem on nonseparating potential flow of an incompressible fluid about an array of profiles reduces to an integral equation for a certain real function, determined on the contours of the profiles of the array. As such a function one can take, as was done, for instance, in [1–5], the relative velocity of the fluid on the profiles of the array. For arrays of profiles of arbitrary shape it is necessary to solve the corresponding integral equation numerically. In the particular examples of the calculation of aerodynamic arrays that are available [1–3] the numerical methods used were based on the approximate evaluation of contour integrals by rectangle formulas. As investigations showed, sizeable errors arose thereby in the approximate solution obtained, these being especially significant in the case of curved profiles of relatively small bulk. In the present paper a method for the numerical solution of the integral equation obtained in [5] is proposed. The method is based on the replacement of a profile of the array with an inscribed N polygon, the length of whose sides is of the order N–1 and whose internal angles are close to . Convergence with increasing N of the numerical solution to an exact solution of the integral equations at the reference points is demonstrated. Examples of the calculation are given.Novosibirsk. Translated from Izvestiya Akademii Nauk SSSR. Mekhanika Zhidkosti i Gaza, No. 2, pp. 105–112, March–April, 1972.  相似文献   

17.
18.
19.
The exact solutions of the nonlinear equations of filtration of an aerated liquid have been obtained in [1–3]. In [4] the system of equations of an aerated liquid have been reduced to the heat-conduction equation under certain assumptions. An approximate method of computing the nonsteady flow of an aerated liquid is given in [5], where the real flow pattern is replaced by a computational scheme of successive change of stationary states. In [6] the same problem is solved by the method of averaging. In the present article estimates of the solution of the equations for nonstationary filtration of an aerated liquid in one-dimensional layer are constructed under certain conditions imposed on the desired functions. These estimates can be used as approximate solutions with known error or for the verification of the accuracy of different approximate methods. We note that the use of comparison theorem for the estimate of solutions of equations of nonlinear filtration is discussed in [7–9]. The methods of constructing estimates of solutions of various problems of heat conduction are given in [10, 11]  相似文献   

20.
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号