用焦散线方法测量集中载荷的误差分析

在实验应力应变分析中，焦散线方法是研究奇异应力场的有效方法．本文以半无限平面受边界压缩载荷作用的问题为例，对集中力作用下的焦散线与分布力作用下的焦散线作了比较，分析了由分布载荷得到的焦散线而计算得到的载荷与施加到试件上的实际载荷之间的误差，并提出了减小误差的措施．     

爆炸载荷下裂纹扩展方向预测的研究

借助动态焦散线方法测试结果,对裂纹尖端初始曲线范围内的第二应力张量不变量分布进行了分析,并通过Det.(iσj)准则对爆炸载荷下裂纹扩展的方向及临界条件进行预测。结果表明,爆炸应力波作用下,裂纹尖端初始曲线范围内第二应力张量不变量最大值与裂纹尖端动态应力强度因子有相同的变化规律,完全可以反映裂纹尖端的动态行为。Det.(iσj)准则用于分析爆炸应力波作用下缺陷介质裂纹扩展行为是十分有效的,特别是对于裂纹起始扩展方向及扩展临界条件有准确的描述。     

高压胶管的动力响应分析

基于钢丝编织高压胶管的纤维加强橡胶复合材料多层圆筒模型,应用连续介质力学有限变形基本理论,建立了周期内压作用下高压胶管的动力学微分模型.通过数值计算得到了高压胶管的时程曲线、频谱图、相图和庞加莱截面图及应力分布曲线,利用非线性动力学理论分析了高压胶管的动力学响应特性,讨论了载荷大小和载荷频率的影响,并分析了高压胶管中的应力分布特征.     

含裂纹三点弯曲梁起始扩展的动态分析

本文利用高速摄影捕捉含裂纹三点弯曲梁在冲击下裂纹扩展过程，借助动态焦散线对裂纹尖端初始曲线范围内的应力第二不变量分布进行了试验研究，并通过Ｄｅｔ．－准则对动载下裂纹起始扩展的条件和方向进行了分析。结果表明：裂纹扩展的实际方向与理论预测相一致；Ｄｅｔ．－准则与焦散线相结合在动态断裂力学研究中具有广泛的使用价值     

焦散线法确定应力强度因子的条件

基于焦散线的形成原理及含裂纹受力试件在裂尖附近区域的应力分布,得到了焦散线法确定应力强度因子的条件：初始曲线半径与试件厚度之比大于0．5。当满足该条件时,对光学各向同性材料及光学各向异性材料前表面反射的情形,只需测量焦散线沿横向的最大尺寸便可较精确地确定应力强度因子;而对于光学各向异性材料的透射或后表面反射情形,只有在忽略远场非奇异应力的影响后,才可借助焦散线的横向尺寸近似确定应力强度因子。     

INVESTIGATION ON FATIGUE HYSTERESIS LOOPS MODELS OF FIBRE-REINFORCED CERAMIC-MATRIX COMPOSITES

纤维增强陶瓷基复合材料初始加载到疲劳峰值应力时, 基体出现裂纹, 纤维/基体界面发生脱粘. 在疲劳载荷作用下, 纤维相对基体在界面脱粘区往复滑移使得陶瓷基复合材料出现疲劳迟滞现象. 建立了纤维陶瓷基复合材料疲劳迟滞回线细观力学模型, 采用断裂力学方法确定了初始加载纤维/基体界面脱粘长度、卸载界面反向滑移长度与重新加载新界面滑移长度, 分析了4种不同界面滑移情况的疲劳迟滞回线. 假设正交铺设与编织陶瓷基复合材料疲劳迟滞回线主要受0°铺层、轴向纱线内纤维/基体界面滑移的影响, 预测了单向、正交铺设与编织陶瓷基复合材料在不同峰值应力与不同循环的疲劳迟滞回线, 与试验结果吻合.     

纤维增强陶瓷基复合材料疲劳迟滞回线模型研究

纤维增强陶瓷基复合材料初始加载到疲劳峰值应力时, 基体出现裂纹, 纤维/基体界面发生脱粘. 在疲劳载荷作用下, 纤维相对基体在界面脱粘区往复滑移使得陶瓷基复合材料出现疲劳迟滞现象. 建立了纤维陶瓷基复合材料疲劳迟滞回线细观力学模型, 采用断裂力学方法确定了初始加载纤维/基体界面脱粘长度、卸载界面反向滑移长度与重新加载新界面滑移长度, 分析了4种不同界面滑移情况的疲劳迟滞回线. 假设正交铺设与编织陶瓷基复合材料疲劳迟滞回线主要受0°铺层、轴向纱线内纤维/基体界面滑移的影响, 预测了单向、正交铺设与编织陶瓷基复合材料在不同峰值应力与不同循环的疲劳迟滞回线, 与试验结果吻合.      

具有中心孔的正交复合材料板在双轴载荷下的应力分析

本文研究了具有中心孔的正交复合材料板在双向载荷下的应力,建立了有限校核系数和双轴率以及之间板宽率的关系,并得到孔边的应力集中系数.这些结果对研究具有中心孔的正交复合材料板在双向载荷下的强度预测和应力分析具有重要的作用.     

使用焦散线法与光弹法测定三维裂纹混合型应力强度因子

本文介绍了将焦散线法与应力冻结，“解冻”技术相结合，使焦散线法用于测量三维体内部裂纹前缘应力强度因子的实验方法，并针对复杂应力状态下三维裂纹前缘的不同应变奇异场，合理地综合运用焦散线法与三维光弹法，实际测量与分离了三维裂纹前缘混合型应力强度因子。     

裂纹在冲击载荷作用下起裂的临界载荷面

采用有限元方法研究裂纹在I型短脉冲载荷作用下应力强度因子随时间的变化 ,用应力强度因子的初始上升时间Tr 对时间坐标无量纲化 ,对应力强度因子初始上升段进行曲线拟合 ,得到了上升段的曲线表达式。运用简单弹性梁理论和Lagrangian运动方程 ,获得载荷与时间对裂纹作用的关系式 ,结合有限元的结果 ,得到了上升时间Tr 的计算表达式 ,并进一步推出了裂纹在冲击载荷作用下起裂的临界载荷面。     

一种基于直接计算高阶奇异积分的断裂力学双边界积分方程分析法

相对于有限元法,边界单元法在求解断裂问题上有着独特的优势,现有的边界单元法中主要有子区域法和双边界积分方程法.采用一种改进的双边界积分方程法求解二维、三维断裂问题的应力强度因子,对非裂纹边界采用传统的位移边界积分方程,只需对裂纹面中的一面采用面力边界积分方程,并以裂纹间断位移为未知量直接用于计算应力强度因子.采用一种高阶奇异积分的直接法计算面力边界积分方程中的超强奇异积分;对于裂纹尖端单元,提供了三种不同形式的间断位移插值函数,采用两点公式计算应力强度因子.给出了多个具体的算例,与现存的精确解或参考解对比,可得到高精度的计算结果.      

汶川地震诱发文家沟巨型滑坡 碎屑流基本特征及成因机制初步分析


2008年5月12日,汶川M80地震在四川省绵竹市清平乡文家沟内诱发一巨型滑坡。通过现场调查得知,滑坡前后缘高差455m,厚度20～30m,滑面为基岩层面,初始方量2750×107m3。滑体在运动中转化为碎屑流。滑坡-碎屑流总的水平运动距离为4022m,垂直运动距离为1443m,遗留的堆积物体积达5×107m3。滑坡距映秀—北川断裂仅36km,位于其下盘,地震烈度达XI度。滑坡导致文家沟中48人遇害,并形成一条完整的地震次生地质灾害链。初步分析表明滑坡启动速度快,滑坡向碎屑流转化过程明显、地点明确。碎屑流运动过程复杂,伴有强烈的“气垫效应”和“前缘气浪冲击效应”。作者认为,文家沟滑坡的高启动速度是长持时强烈地震动作用的结果,与山体的猛烈碰撞是导致滑体解体并转化为碎屑流的原因。     

Preface: Orbits around asteroid

One of the core issues in modern celestial mechanics is the orbital dynamics in the near-regime gravitational field of as- teroids, which provides deep insights into the mathematical nature of a class of nonlinear systems, and plays as a critical basis for in situ explorations of different science goals. Lots of efforts have been made to reveal the characteristics of orbital motion in the vicinity of asteroids, and to improve the skills of asteroid research in methodology.     

Effet de l'anisotropie élastique cristalline sur la distribution des facteurs de Schmid à la surface des polycristauxInfluence of crystalline elasticity anisotropy on Schmid factor distribution at the free surface of polycrystals

Experimental studies of the plasticity mechanisms of polycrystals are usually based on the Schmid factor distribution supposing crystalline elasticity isotropy. A numerical evaluation of the effect of crystalline elasticity anisotropy on the apparent Schmid factor distribution at the free surface of polycrystals is presented. Cubic elasticity is considered. Order II stresses (averaged on all grains with the same crystallographic orientation) as well as variations between averages computed on grains with the same crystallographic orientation but with different neighbour grains are computed. The Finite Element Method is used. Commonly studied metals presenting an increasing anisotropy degree are considered (aluminium, nickel, austenite, copper). Concerning order II stresses in strongly anisotropic metals, the apparent Schmid factor distribution is drifted towards small Schmid factor values (the maximum Schmid factor is equal to 0.43 instead of 0.5) and the slip activation order between characteristic orientations of the crystallographic standard triangle is modified. The computed square deviations of the stresses averaged on grains with the same crystallographic orientation but with different neighbour grains are a bit higher than the second order ones (inter-orientation scatter). Our numerical evaluations agree quantitatively with several observations and measures of the literature concerning stress and strain distribution in copper and austenite polycrystals submitted to low amplitude loadings. Hopefully, the given apparent Schmid factor distributions could help to better understand the observations of the plasticity mechanisms taking place at the free surface of polycrystals. To cite this article: M. Sauzay, C. R. Mecanique 334 (2006).     

Nonlinear behavior of matrix-inclusion composites under high confining pressure: application to concrete and mortar

This paper is devoted to a micromechanics-based simulation of the response of concrete to hydrostatic and oedometric compressions. Concrete is described as a composite made up of a cement matrix in which rigid inclusions are embedded. The focus is put on the role of the interface between matrix and inclusion which represent the interfacial transition zone (ITZ). A plastic behavior is considered for both the matrix and the interfaces. The effective response of the composite is derived from the modified secant method adapted to the situation of imperfect interfaces. To cite this article: T.H. Le et al., C. R. Mecanique 336 (2008).     

Dynamics and Breakup of Viscoelastic Liquids (A Review)

The phenomena of hydrodynamic breakup of liquid jets, drops, films, bridges, and filaments are reviewed for liquids with viscoelastic properties. The reasons for breakup are capillary instabilities, collisions with rigid obstacles, and other forms of dynamic action. The relationship between the properties of the liquids and the features of the breakup process is discussed.     

Flow stability analysis and excitation using pulsating jets

Classical flow stability applied to transition from laminar to turbulent flow may also describe the behavior of vorticity fluctuations created by a pulsating jet placed along a solid boundary. A numerical laminar flow experiment involving a pulsating jet placed along the surface of a duct with flow separation downstream, resulted in eliminating most part of the separated flow region. Applying the same approach to a turbulent flow, it was possible to develop a turbulent stability flow formulation and apply successfully turbulent pulsating jet flow separation control. To cite this article: D. Skamnakis, K. Papailiou, C. R. Mecanique 333 (2005).