共查询到17条相似文献,搜索用时 125 毫秒
1.
2.
大面积金属板材304L/Q235B的爆炸焊接过程涉及炸药爆轰、金属板材的高速碰撞和塑性变形等。采用有限元法计算模拟这个问题时,网格单元会发生扭曲畸变现象,导致计算精度下降,甚至出现单元负体积而使计算终止,并且炸药爆轰形成气体产物飞散过程也很难模拟。为了能模拟大面积金属板材的爆炸焊接整个过程并获得合理的技术工艺参数,采用物质点法进行三维数值模拟分析。物质点法作为一种无网格法,在模拟冲击动力学问题中主要采用显式积分算法。通过将拉格朗日质点单元与固定的欧拉背景网格相结合,可以实现爆炸焊接的复板与基板的高速碰撞、炸药滑移爆轰、金属板面的塑性变形过程的数值模拟,并给出爆炸复合板材的形变、有效塑性应变和复板与基板的碰撞速度的计算结果。采用物质点法模拟的复合板材变形与爆炸焊接实验结果基本一致。计算复板与基板的碰撞速度这个重要的物理参数时,物质点法与Richter理论公式的相对误差不超过13%。数值计算和实验结果表明,物质点法在数值精度和计算效率方面具有优势,物质点法是研究金属焊接爆炸问题的一种有效数值方法。 相似文献
3.
4.
5.
6.
为了研究爆炸焊接结合界面机理及材料强度对爆炸焊接的影响,采用相同的爆炸焊接参数对不同强度的基板进行了爆炸焊接。通过光学显微镜、扫描电子显微镜以及数值模拟技术对焊接试样的形貌、缺陷以及焊接机理进行了分析。结果表明:当材料强度较低时,碰撞点动压与基板材料强度的比值较高,界面出现较大的塑性应变并生热,此时界面熔化区较大,在焊接过程中可以将界面等效为不可压缩流体;当材料强度较高而碰撞点动压与基板强度的比值较低时,试样界面形貌受材料强度的影响较大。随着材料强度的上升,周期性的波状界面逐渐趋于平直。界面熔化现象减弱但温升速率较高,并受碰撞点附近高压出现热失稳现象形成剪切带及裂缝。此时材料强度的影响不可忽略,界面不能等效为不可压缩流体。 相似文献
7.
钛/钢复合板爆炸焊接实验 总被引:1,自引:0,他引:1
以3mm 厚的TA2钛板和26mm 厚的正火态Q345R为材料,通过爆炸焊接实验,对钛/钢复合板
爆炸焊接的动态参数进行了研究。结合复合板结合界面特征、复合板结合强度(剪切强度)以及界面波的金相
组织,讨论了钛/钢爆炸焊接时获得高强度结合和规则的界面结合波状形态的条件。对于3mm 厚TA2与
26mm厚正火态Q345R,该条件是动态碰撞角17,动态碰撞速度vp760m/s。根据界面波及基板轧制
金相组织形态,分析了形成界面波的机理,认为射流阻碍复板连续碰撞基板是形成界面波的一个主要原因。 相似文献
8.
利用物质点法求解三维远场水下爆炸冲击响应问题时,爆炸冲击波到达结构物之前传播过程的计算会消耗大量的计算资源,影响求解效率。针对这一问题,并考虑到水下爆炸冲击波在自由场中的传播特点,提出了一维球对称形式的物质点法,对球形炸药水下爆炸过程进行了数值模拟,并与Cole公式以及DYNA计算结果进行了比较,结果吻合较好,验证了一维球对称形式物质点法的正确性。在此基础上,提出了基于物质点法的重映射算法,将爆炸冲击波在自由场中的传播过程在一维球对称模型中进行计算,并将计算结果映射到三维模型中,以便继续完成计算过程,有效避免了计算资源在冲击波传播过程计算上的消耗。 相似文献
9.
编写了适用于模拟具有高密度比、高压力比的强激波问题的二维柱对称多介质流体计算程序。利用有限体积方法求解流体的Euler方程组,采用level set方法捕捉爆炸产物与空气的运动界面,并通过求解物质界面两侧Riemann问题的精确解来计算爆炸产物与空气之间的数值通量。研制了三角形网格自适应技术来实现网格的自动加密和粗化,在保证捕捉激波峰值的前提下有效地提高了计算效率。利用计算程序对1 kt TNT当量的空气自由场强爆炸问题进行数值模拟,计算得到的峰值超压、冲击波到达时间等物理参数与点爆炸理论结果基本一致。 相似文献
10.
基于ANSYS/LS-DYNA有限元分析软件对加油站埋地储油罐的爆炸过程进行了数值模拟。根据范登伯格和兰诺伊TNT当量法,将汽油转换成相对应的TNT当量;针对埋地储油罐具体覆土情况采用相应的材料模型,建立了有限元分析模型;采用多物质耦合ALE方法进行爆炸过程的模拟,弥补了采用G·M莱克霍夫计算方法对加油站储罐爆炸进行定量分析时因无法充分考虑埋深、自由面影响以及土质材料特性而产生的不足;通过数值模拟得到了爆炸作用下各观测点的冲击波压力时程曲线和峰值压力,并与G·M莱克霍夫公式的计算结果进行了对比,二者具有相同的变化规律。数值模拟得到的地表处各点的峰值压力可作为判断该点人和建筑物的伤害和破坏程度的依据,为事故分析和新项目建设提供参考。 相似文献
11.
S. P. Kiselev 《Journal of Applied Mechanics and Technical Physics》2012,53(6):907-917
Results of numerical simulations of wave formation in an oblique symmetric impact of metal plates by the method of molecular dynamics are presented. In this case, the impacting plates experience the same loading conditions as in explosive welding. It is demonstrated that the evolution of waves on the interface between the welded plates is caused by self-induced oscillations in the vicinity of the contact point. A mechanism of building-up and sustaining of self-induced oscillations is proposed on the basis of numerical calculations performed. 相似文献
12.
Some of the main progress on the investigation of the mechanism of the wave formation in explosive welding at the Institute
of Mechanics is summarized and others' previous works are reviewed. Our systematic experiments and analysis do not substantiate
the theory of wave formation based on Karman vortex-street analogy or Helmholtz instability. On the contrary, they show that
material strength insensitive to strain rate plays an important role. A simple hydro-plastic model is presented to explain
the main features regarding the interfacial wave formation and to estimate the magnitude of wave length. The result is in
broad agreement with experiment. 相似文献
13.
14.
为了考察钛作为过渡层提高锆/钢复合板结合强度的有效性,同时给出合理的爆炸焊接碰撞参数,对双层锆/钢和三层锆/钛/钢进行了小倾角法爆炸焊接实验研究。借助金相显微技术测量了复合板结合界面的波形参数,采用光滑粒子动力学法模拟得到了不同位置的碰撞速度和碰撞角,并按照国家标准(GB/T 6396-2008)测量了复合板结合界面的爆炸态及退火态的剪切强度。结果表明:钛作为过渡层能够显著提高锆/钢界面的剪切强度;退火消除加工应力后,锆/钢及钛/钢结合面的剪切强度会有所降低;当锆/钛界面的碰撞速度为734~805 m/s,碰撞角为19.8°~20.8°,钛/钢界面的碰撞速度为803~904m/s,碰撞角为19.5°~20.5°时,锆/钛/钢三层复合板的锆/钛和钛/钢界面的剪切强度都能高于140 MPa。 相似文献
15.
16.
This paper investigates the complex interfacial kinematics and governing mechanisms during high speed impact conditions. A robust numerical modelling technique using Eulerian simulations are used to explain the material response of the interface subjected to a high strain rate collision during a magnetic pulse welding. The capability of this model is demonstrated using the predictions of interfacial kinematics and revealing the governing mechanical behaviours. Numerical predictions of wave formation resulted with the upward or downward jetting and complex interfacial mixing governed by wake and vortex instabilities corroborate the experimental observations. Moreover, the prediction of the material ejection during the simulation explains the experimentally observed deposited particles outside the welded region. Formations of internal cavities along the interface is also closely resemble the resulted confined heating at the vicinity of the interface appeared from those wake and vortex instabilities. These results are key features of this simulation that also explains the potential mechanisms in the defects formation at the interface. These results indicate that the Eulerian computation not only has the advantage of predicting the governing mechanisms, but also it offers a non-destructive approach to identify the interfacial defects in an impact welded joint. 相似文献
17.
对爆轰加载下低熔点金属锡的层裂破碎问题开展了数值模拟。在利用实验数据对所采用数值方法和材料模型开展对比验证的基础上,通过对样品内部物理量时间及空间分布演化对比分析,剖析了冲击加-卸载中样品内部应力波与材料相互作用过程。此外,通过对比分析不同厚度锡样品在爆轰加载下的动态行为特征,进一步认识了自由面反射稀疏波、边侧稀疏波和入射稀疏波共同作用下层裂破碎演化机制。结果表明,当样品较薄时,层裂破碎行为由反射稀疏波主导;随着样品厚度的增大,反射稀疏波主导区缩小,入射稀疏波和边侧稀疏波主导区逐渐增大。 相似文献