首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 125 毫秒
1.
应用谐波小波提取转子系统动力参数   总被引:2,自引:1,他引:1  
临界转这是离心压缩机转子系统的主要动力参数之一,尤其高阶临界转速在试车中不易被识别。本文应用谐波小波对转子系统试车振动信号进行分析,对转子高阶临界转速进行了分辨识别,结果令人满意。  相似文献   

2.
在现代高速旋转机械中,不平衡引起的振动是机器性能降低甚至损坏的重要原因。对变速转子准稳态主动平衡系统,可按一定时间步长把变转速离散成有限个转动角速度。针对每个离散角速度,依据影响系数法,采用包含残余振动值和校正不平衡的广义线性二次型目标性能函数推导出控制律。通过每个离散转速下影响系数的估计和增益矩阵的计算,形成对应于各离散转速的增益表,从而实现变速转子准稳态主动平衡系统的增益调度控制。数值模拟验证了增益调度控制能很好地抑制不平衡振动。与传统的加权二乘法(WLS)相比,数值模拟显示,该法对校正不平衡的惩罚可提高系统的稳定性,也可增强控制的鲁棒性。  相似文献   

3.
在工程实际中,涡轮机叶片的转速在很多应用场景下不是一个定常值,比如发动机在启动、变速、停机等工况下,转子输入与输出功率失衡,伴随产生扭振,产生速度脉冲. 另外,由于服役环境、安装误差等因素会引起叶片在所难免的预变形. 本文主要研究预变形叶片,在变转速条件下的非线性动力学行为. 考虑叶片转速由一定常转速和一简谐变化的微小扰动叠加而成. 应用拉格朗日原理得到变转速叶片的动力学控制方程,并采用假设模态法将偏微分方程转为常微分方程,通过引入无量纲,使方程更具有一般性. 运用多尺度方法求解了该参激振动系统,得到了在 2:1 内共振情形下的平均方程,进而获得系统的稳态响应. 详细研究温度梯度、阻尼以及转速扰动幅值等系统参数对叶片动力学响应的影响规律,同时考察了立方项在 2:1 内共振下对方程的影响. 对原动力方程进行正向、反向扫频积分来观察其跳跃现象,并对解析解进行验证. 结果发现参数的变化对叶片均有不同程度影响,在 2:1 内共振下立方项对系统响应的影响很小,解析解与数值解吻合很好.  相似文献   

4.
汽轮机转子在气流力和油膜力作用下的非线性动力学特性   总被引:2,自引:0,他引:2  
为了分析转子在油膜力和气流激振力共同作用下的非线性振动特性,本文以短轴承支撑的不平衡刚性对称Jeffcott转子系统为研究对象,首先分析转子在非稳态油膜力作用下的振动特性,然后分析转子在油膜力和气流激振力共同作用下的非线性振动特性。采用数值模拟的方法研究了系统的分岔和混沌特性,计算结果表明,考虑气流激振力和油膜力共同作用下的转子系统与仅考虑油膜力的转子系统相比,在相对进气速度v=30m/s时,随着无量纲转速ω的增加。二者都出现了周期运动和混沌运动多次交替出现的复杂运动特性,但是前者首次出现倍周期分岔和混沌运动时的转运提前,在定转速情况下,随着v的增大,系统最终在经历周期运动之后进入混沌运动,而且圆盘中心的最大振幅随着v的增大而增大。  相似文献   

5.
顾伟  张博  丁虎  陈立群 《力学学报》2020,52(4):1131-1142
在工程实际中,涡轮机叶片的转速在很多应用场景下不是一个定常值,比如发动机在启动、变速、停机等工况下,转子输入与输出功率失衡,伴随产生扭振,产生速度脉冲. 另外,由于服役环境、安装误差等因素会引起叶片在所难免的预变形. 本文主要研究预变形叶片,在变转速条件下的非线性动力学行为. 考虑叶片转速由一定常转速和一简谐变化的微小扰动叠加而成. 应用拉格朗日原理得到变转速叶片的动力学控制方程,并采用假设模态法将偏微分方程转为常微分方程,通过引入无量纲,使方程更具有一般性. 运用多尺度方法求解了该参激振动系统,得到了在 2:1 内共振情形下的平均方程,进而获得系统的稳态响应. 详细研究温度梯度、阻尼以及转速扰动幅值等系统参数对叶片动力学响应的影响规律,同时考察了立方项在 2:1 内共振下对方程的影响. 对原动力方程进行正向、反向扫频积分来观察其跳跃现象,并对解析解进行验证. 结果发现参数的变化对叶片均有不同程度影响,在 2:1 内共振下立方项对系统响应的影响很小,解析解与数值解吻合很好.   相似文献   

6.
含慢变参数的非线性振动系统的振动特性   总被引:4,自引:0,他引:4  
慢变参数的振动系统一类典型的非线性系统,工程上的许多振动都于这一类,由于慢变系统的质量、刚度、干扰力等参数是随机时间缓慢的,另一般的参变系统有本质的不同,因此需根据咖以研究。本文讨论了慢变系统的分析方法。同时结合提升机罐笼与钢丝强组成的系统和慢变刚度的转子系统对自汉的和非自治的慢变系统的的夺动特性进行了研究,提出育夺区时的振幅的具体方法。  相似文献   

7.
分析了在动载轴承非稳态非线性油膜力作用下,具有横向裂纹柔性轴Jeffcott转子在非线性涡动影响下的动力特性。通过数值计算表明,在油膜失稳转速前,随着裂纹轴刚度变化比的增大,系统在低转速区域内具有丰富的非线性动力行为,出现倍周期分叉及混沌现象,涡动振幅随转速升高而减小,直到非稳态非线性油膜失稳,在无裂纹转子油膜临界失稳点处发现了类Hopf分叉现象,系统运动由平衡变为拟周期运动;裂纹转子在油膜临界失稳时的系统运动亦为拟周期运动,裂纹转子轴刚度变化对油膜失稳点及油膜失稳之后转子的运动影响不大,转子系统作拟周期运动。  相似文献   

8.
研究了受横向不平衡电磁激励的转子.轴承系统的非线性振动响应。首先将转子.轴承系统简化为带有质量不平衡并受横向激励的连续梁,由于短轴承的油膜力和电磁力的共同激励,系统振动具有强非线性特性。用Galerkin方法把偏微分控制方程离散为常微分方程组,采用四阶Runge—Kutta法对该系统进行数值仿真研究。其次比较了转轴分别在电磁力、油膜力单独作用和两种力共同作用下的振动特性,研究表明电磁力和油膜力对转子系统的非线性振动和分岔有着不同的贡献:油膜力的存在抑制了拟周期运动的发生,延长了稳定运行区域;电磁力拉长了拟周期发生的区域,降低了转子系统发生突发性破坏的风险。最后给出了系统响应随转速、电磁参数、油膜粘度等控制参数变化的分岔图,表明:系统在两个方向的运动随控制参数的变化趋势基本相同,经历了周期、倍周期、拟周期等非线性运动交替出现的过程;且油膜粘度的增大有利于转子系统的安全运行。  相似文献   

9.
非线性转子动力学的稳定性和分岔   总被引:2,自引:0,他引:2  
大型高速转子的工作转速往往超过其第一阶临界转速,咽而需要考虑系统的非线性刚度和转轴材料的内阻尼对轴振动特性的影响。本文研究非线性围各阶共振点(临界转速)时的稳定性,并应用奇异性理论拱皋地转轴的定常运动(同步涡动)和自激振动(非同步涡动)周期响应的分岔。本文的结论不仅揭示了非线性转子丰富的动力学形为,对对大型高速转子的稳定性控制有一定参考价值。  相似文献   

10.
针对非线性磁浮轴承转子系统的特点,建立了刚性磁浮轴承转子系统的非线性动力学方程。运用多尺度法研究了系统主参激共振的一次、二次近似稳态响应。结果表明,二次非线性项对系统稳定性有重要影响。为更好控制磁浮轴承转子系统运行状态提供了理论参考。  相似文献   

11.
Min  Chaoqing  Dahlmann  Martin  Sattel  Thomas 《Nonlinear dynamics》2021,103(1):239-254

A novel semi-active vibration control concept with a serial-switch-stiffness-system was previously presented in our work. Differing from conventional vibration control systems, this system does not dissipate but converts vibration energy as potential energy stored in springs and then reacts against external disturbance. As a piecewise linear system, whether or not energy conversion limit happens is an interesting nonlinear dynamic issue related to the systems steady state response. This paper formulates this issue in depth using the approach called equivalence in control. The systems control force represented by the converted vibration energy is approximately decomposed into two portions. One is responsible for low-frequency free response and the other for high-frequency switching response. An equivalent linear system suffering from a decomposed high-frequency switching force is obtained instead of the original switched system. The steady state response of the disturbed system can be delivered through linear superposition as executed in a linear system. Energy conversion limit occurring in the system under a harmonic disturbance is numerically shown by means of fast Fourier transformation. Analytical formulation and numerical simulation for open- and closed-loop control of the system are further carried out, respectively. The results give that the proposed approach is capable of solving the stead state response of the switched system accurately, and meanwhile, energy conversion limit occurs in the vibration control system indeed. Experimental discussion is also executed.

  相似文献   

12.
The robust adaptive fuzzy control problem is investigated for a single machine bus system with static var compensator (SVC). This design does not require that speed of the generator rotor and susceptance of the overall system are measured, and also does not require that the parameters of controlled system are known accurately. The fuzzy logic systems are used to approximate the nonlinear functions of the system, and a fuzzy state observer is designed to estimate the speed of the generator rotor and susceptance. By utilizing the fuzzy state observer, and combining the adaptive backstepping technique with adaptive fuzzy control design, an observer-based adaptive fuzzy output-feedback control approach is developed. It is proved that the proposed control approach can guarantee that all the signals in the closed-loop system are semiglobally uniformly ultimately bounded (SGUUB), and the angle of the generator rotor follows a desired value. Simulation results are presented to show the effectiveness of the approach.  相似文献   

13.
The study of the transport phenomena in desiccant airflow systems has been addressed in numerous research works, some of them concerning combined processes of cooling, dehumidification and energy recovery. In this paper a detailed numerical model is used to simulate the behaviour of a parallel-plate channel, cyclically exposed to two airflows with different inlet conditions, the plate being composed by a substrate and a desiccant porous layer. The modelled channel is considered to be representative of a real channel of a hygroscopic matrix that is operating at steady state regime, like it occurs in desiccant or enthalpy rotors. The numerical results are treated in order to represent the global behaviour of the hygroscopic rotor under steady state conditions. Results of a parametric study are presented as maps of isovalues of the heat and mass transfer rates and of the outlet states of both airflows, considering channels of distinct wall thickness, of different thickness of the desiccant and the subtract layers, together with wide ranges of the rotation speed and of the wheel partition. The mapped results presented provide an overview of the operation characteristics of hygroscopic rotors, allowing a quick determination of the optimum range of values for relevant parameters, such as the rotation speed and the wheel partition. The model is thus an interesting tool for design and manufacture purposes of enthalpy and desiccant wheels.  相似文献   

14.
为了考虑高速列车、板式无砟轨道和桥梁相互作用的特点,需将列车模拟为质量-弹簧-阻尼多刚体相互约束的系统,通过列车车轮与钢轨的接触关系,建立车-轨-桥耦合系统的运动方程。重点分析了双线列车以不同工况通过高速铁路桥梁时,列车行驶状态(速度和加速度)、列车悬挂系数和钢轨-轨道-桥梁连接参数分别对车-轨-桥耦合系统的动力学性能影响。结果表明,(1)列车的加速度和速度的变化对耦合系统有不同程度的影响,随着列车行驶速度与加速度在一定范围内增加,车体自身结构的位移振动响应逐渐减小,而钢轨和桥梁结构的位移振动响应则不断增加;(2)列车悬挂参数的改变对列车自身结构影响较大,而对钢轨和桥梁结构影响很小;(3)车体一系刚度系数增大会引起列车系统结构振动响应变大,但车体二系刚度系数的增加却抑制了车体结构的振动响应;(4)除了钢轨的最大加速度随着连续刚度系数增加呈线性递减外,列车、钢轨和桥梁的振动响应不易受钢轨与桥梁间连接参数的影响。  相似文献   

15.
王宝森  刘永强  张斌 《力学学报》2022,54(7):1839-1852
高速列车的发展使得其关键零部件——轴承的安全问题日益突出. 现有的轴承模型均是建立在匀速工况下, 不能描述系统在变转速工况下运动状态. 为了解决这个问题, 建立了一个变转速工况下高速列车轴箱轴承转子系统动力学模型, 模型通过角度迭代计算得到了滚动体在不均匀时间内转过的总角度, 进而确定了滚动体在任意时刻的空间位置. 在匀速工况和变转速工况下, 对具有外圈故障的轴承模型进行了实验对比, 验证了模型的有效性. 利用轴心轨迹定性分析了外圈故障、内圈故障和滚动体故障对系统稳定性的影响, 并通过实验验证了分析结果的可靠性. 利用二维不变矩作为特征指标定量分析了三类故障对系统稳定性的影响. 分析结果表明: 当轴承角加速度较小时, 外圈故障对系统稳定性影响最大; 当轴承角加速度较大时, 滚动体故障对系统稳定性影响最大, 但是影响程度随着故障尺寸的变大而逐渐减小. 同样地, 利用二维不变矩作为特征指标进行了系统的稳定性临界状态分析, 确定了在不同转速工况下和不同故障类型下临界状态对应的最大故障尺寸. 研究结果表明: 随着轴承内圈转速的上升, 不同故障类型对应的最大尺寸都会减小, 其中滚动体故障尺寸大都是最小的, 说明滚动体故障对系统稳定性影响最大.   相似文献   

16.
电动机-弹性连杆机构系统的动态方程及其响应   总被引:2,自引:0,他引:2  
针对三相交流电机转子振动偏心时不均匀气隙的气隙磁场,分析其实际运行状态的机电耦合关系.建立以电机横振、扭振为节点位移的电机单元,应用有限单元法建立含电机电磁参数和弹性连杆机构结构参数的系统动态方程,并根据该方程对系统的动态响应进行仿真计算和分析,且通过实验进行验征,表明所建方程较好地反映丁系统动态性能与其电磁参数、结构参数之间的关系.  相似文献   

17.
Traditional rotor dynamics mainly focuses on the steady- state behavior of the rotor and shafting. However, for systems such as hydro turbine generating sets (HTGS) where the control and regulation is frequently applied, the shafting safety and stabilization in transient state is then a key factor. The shafting transient state inevitably involves multiparameter domain, multifield coupling, and coupling dynamics. In this paper, the relative value form of the Lagrange function and its equations have been established by defining the base value system of the shafting. Taking the rotation angle and the angular speed of the shafting as a link, the shafting lateral vibration and generator equations are integrated into the framework of generalized Hamiltonian system. The generalized Hamiltonian control model is thus established. To make the model more general, additional forces of the shafting are taken as the input excitation in proposed model. The control system of the HTGS can be easily connected with the shafting model to form the whole simulation system of the HTGS. It is expected that this study will build a foundation for the coupling dynamics theory using the generalized Hamiltonian theory to investigate coupling dynamic mechanism among the shafting vibration, transient of hydro turbine generating sets, and additional forces of the shafting.  相似文献   

18.
Conditions of stability in sliding mode are obtained for nonstationary dynamic automatic-control processes of variable structure. The nonstationary parameters of a control process subjected to external perturbations vary in given ranges, whereas the parameters of the switching plane remain constant for the appropriately chosen parameters of discontinuous logic control laws. The corresponding system of differential equations contains coefficients that vary stepwise in time together with the parameters of the controlled process. The general stability criteria for the solutions of variable-structure systems are used to analyze the stability of motion in sliding mode of an automatic variable-structure control system of the second order  相似文献   

19.
根据列车具体的轴距和轴重,建立了和谐号动车组CRH380AL型列车简化模型;对高速铁路两跨连续梁桥采用多自由度欧拉伯努利梁单元进行主梁的模拟,并将液体黏滞阻尼器模拟为有限元阻尼单元;采用Newmark直接积分方法求解了高速列车作用下的连续梁桥运动方程,数值分析了列车车速以及液体黏滞阻尼器的阻尼系数对于高速铁路连续梁桥振动响应的影响。结果表明:黏滞阻尼器对于桥梁具有明显的减振效果,阻尼力不仅与阻尼系数有关还与列车时速有关;同一黏滞阻尼器条件下,桥梁的最大加速度并不随列车速度的增加而单调增加,而是在某些特定列车车速下桥梁的最大加速度出现了峰值,且随着黏滞阻尼器的阻尼系数增大,桥梁振动响应峰值处的最大加速度减幅不同;同一列车时速的条件下,桥梁的减振效果并不是随着阻尼系数的递增呈正比递增,而是随着阻尼系数的增大,阻尼器的减振效果增幅在减小。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号