Theoretical and experimental analysis of longitudinal wave propagation in cylindrical viscoelastic rods

Wave propagation in viscoelastic rods is encountered in many applications including studies of impact and fracture under high strain rates and characterization of the dynamic behavior of viscoelastic materials. For viscoelastic materials, both material and geometric dispersion are possible when the diameter of the rod is of the same order as the wavelength. In this work, we simplify the Pochhammer frequency equation for low and intermediate loss viscoelastic materials and formulate corrections for geometric dispersion for both the phase velocity and attenuation. The formulation is then experimentally verified with measurements of the phase velocity and attenuation in commercial polymethylmethacrylate rods that are 12 and in diameter. Without correcting for geometric dispersion, the usable frequency range for determining the phase velocity and attenuation for the rod is about , and about for the rod. Using the correction procedure developed here, it was possible to accurately determine the phase velocity and attenuation up to frequencies exceeding for the rod and for the rod. These corrections are applicable to many polymers and other viscoelastic materials. From thereon, the viscoelastic properties of the material can be determined over a wide range of frequencies.     

Limit analysis of multi-layered plates. Part I: The homogenized Love-Kirchhoff model

The purpose of this paper is to determine , the overall homogenized Love-Kirchhoff strength domain of a rigid perfectly plastic multi-layered plate, and to study the relationship between the 3D and the homogenized Love-Kirchhoff plate limit analysis problems. In the Love-Kirchhoff model, the generalized stresses are the in-plane (membrane) and the out-of-plane (flexural) stress field resultants. The homogenization method proposed by Bourgeois [1997. Modélisation numérique des panneaux structuraux légers. Ph.D. Thesis, University Aix-Marseille] and Sab [2003. Yield design of thin periodic plates by a homogenization technique and an application to masonry wall. C. R. Méc. 331, 641-646] for in-plane periodic rigid perfectly plastic plates is justified using the asymptotic expansion method. For laminated plates, an explicit parametric representation of the yield surface is given thanks to the π-function (the plastic dissipation power density function) that describes the local strength domain at each point of the plate. This representation also provides a localization method for the determination of the 3D stress components corresponding to every generalized stress belonging to . For a laminated plate described with a yield function of the form , where σ^u is a positive even function of the out-of-plane coordinate x₃ and is a convex function of the local stress σ, two effective constants and a normalization procedure are introduced. A symmetric sandwich plate consisting of two Von-Mises materials ( in the skins and in the core) is studied. It is found that, for small enough contrast ratios (), the normalized strength domain is close to the one corresponding to a homogeneous Von-Mises plate [Ilyushin, A.-A., 1956. Plasticité. Eyrolles, Paris].     

Geometrical properties of the vorticity vector derived using large-eddy simulation

In this paper, the geometrical properties of the resolved vorticity vector derived from large-eddy simulation are investigated using a statistical method. Numerical tests have been performed based on a turbulent Couette channel flow using three different dynamic linear and nonlinear subgrid-scale stress models. The geometrical properties of have a significant impact on various physical quantities and processes of the flow. To demonstrate, we examined helicity and helical structure, the attitude of with respect to the eigenframes of the resolved strain rate tensor and negative subgrid-scale stress tensor -τ_ij, enstrophy generation, and local vortex stretching and compression. It is observed that the presence of the wall has a strong anisotropic influence on the alignment patterns between and the eigenvectors of , and between and the resolved vortex stretching vector. Some interesting wall-limiting geometrical alignment patterns and probability density distributions in the form of Dirac delta functions associated with these alignment patterns are reported. To quantify the subgrid-scale modelling effects, the attitude of with respect to the eigenframe of -τ_ij is studied, and the geometrical alignment between and the Euler axis is also investigated. The Euler axis and angle for describing the relative rotation between the eigenframes of -τ_ij and are natural invariants of the rotation matrix, and are found to be effective for characterizing a subgrid-scale stress model and for quantifying the associated subgrid-scale modelling effects on the geometrical properties of .     

Nanoindentation and the indentation size effect: Kinetics of deformation and strain gradient plasticity

A study of the indentation size effect (ISE) in aluminum and alpha brass is presented. The study employs rate effects to examine the fundamental mechanisms responsible for the ISE. These rate effects are characterized in terms of the rate sensitivity of the hardness, , where H is the hardness and is an effective strain rate in the plastic volume beneath the indenter. can be measured using indentation creep, load relaxation, or rate change experiments. The activation volume V∗, calculated based on which can traditionally be used to compare rate sensitivity data from a hardness test to conventional uniaxial testing, is calculated. Using materials with different stacking fault energy and specimens with different levels of work hardening, we demonstrate how increasing the dislocation density affects V∗; these effects may be taken as a kinetic signature of dislocation strengthening mechanisms. We noticed both H and exhibit an ISE. The course of V∗ vs. H as a result of the ISE is consistent with the course of testing specimens with different level of work hardening. This result was observed in both materials. This suggests that a dislocation mechanism is responsible for the ISE. When the results are fitted to a strain gradient plasticity model, the data at deep indents (microhardness and large nanoindentation) exhibit a straight-line behavior closely identical to literature data. However, for shallow indents (nanoindentation data), the slope of the line severely changes, decreasing by a factor of 10, resulting in a “bilinear behavior”.     

Formation of molten metal films during metal-on-metal slip under extreme interfacial conditions

The present paper describes results of plate-impact pressure-shear friction experiments conducted to study time-resolved growth of molten metal films during dry metal-on-metal slip under extreme interfacial conditions. By employing tribo-pairs comprising hard tool-steel against relatively low melt-point metals such as 7075-T6 aluminum alloys, interfacial friction stress ranging from 100 to and slip speeds of approximately have been generated. These relatively high levels of friction stress combined with high slip-speeds generate conditions conducive for interfacial temperatures to approach the melting point of the lower melt point metal (Al alloy) comprising the tribo-pair.A Lagrangian finite element code is developed to understand the evolution of the thermo-mechanical fields and their relationship to the observed slip response. The code accounts for dynamic effects, heat conduction, contact with friction, and full thermo-mechanical coupling. At temperatures below the melting point the material is described as an isotropic thermally softening elastic-viscoplastic solid. For material elements with temperatures in excess of the melt point a purely Newtonian fluid constitutive model is employed.The results of the hybrid experimental-computational study provides new insights into the thermoelastic-plastic interactions during high speed metal-on-metal slip under extreme interfacial conditions. During the early part of frictional slip the coefficient of kinetic friction is observed to decrease with increasing slip velocity. During the later part transition in interfacial slip occurs from dry metal-on-metal sliding to the formation of molten Al films at the tribo-pair interface. Under these conditions the interfacial resistance approaches the shear strength of the molten aluminum alloy under normal pressures of approximately 1- and shear strain rates of . The results of the study indicate that under these extreme conditions molten aluminum films maintain a shearing resistance as high as .Scanning electron microscopy of the slip surfaces reveal molten aluminum to be smeared on the tribo-pair interface. Knoop hardness measurements in 7075-T6 Al alloy at various depths from the slip interface indicate that the hardness increases approximately linearly with depth and reaches a plateau at approximately from the surface.     

Plasticity size effects in free-standing submicron polycrystalline FCC films subjected to pure tension

The membrane deflection experiment developed by Espinosa and co-workers was used to examine size effects on mechanical properties of free-standing polycrystalline FCC thin films. We present stress-strain curves obtained on films 0.2, 0.3, 0.5 and thick including specimen widths of 2.5, 5.0, 10.0 and for each thickness. Elastic modulus was consistently measured in the range of 53- for Au, 125- for Cu and 65- for Al. Several size effects were observed including yield stress variations with membrane width and film thickness in pure tension. The yield stress of the membranes was found to increase as membrane width and thickness decreased. It was also observed that thickness plays a major role in deformation behavior and fracture of polycrystalline FCC metals. A strengthening size scale of one over film thickness was identified. In the case of Au free-standing films, a major transition in the material inelastic response occurs when thickness is changed from 1 to . In this transition, the yield stress more than doubled when film thickness was decreased, with the thick specimen exhibiting a more brittle-like failure and the thick specimen exhibiting a strain softening behavior. Similar plasticity size effects were observed in Cu and Al. Scanning electron microscopy performed on Au films revealed that the number of grains through the thickness essentially halved, from approximately 5 to 2, as thickness decreased. It is postulated that this feature affects the number of dislocations sources, active slip systems, and dislocation motion paths leading to the observed strengthening. This statistical effect is corroborated by the stress-strain data in the sense that data scatter increases with increase in thickness, i.e., plasticity activity.The size effects here reported are the first of their kind in the sense that the measurements were performed on free-standing polycrystalline FCC thin films subjected to macroscopic homogeneous axial deformation, i.e., in the absence of deformation gradients, in contrast to nanoindentation, beam deflection, and torsion, where deformation gradients occur. To the best of our understanding, continuum plasticity models in their current form cannot capture the observed size scale effects.     

Micromechanics of residual stress and texture development due to poling in polycrystalline ferroelectric ceramics

This paper presents micromechanics based analysis of elastic strain and changes in the texture of poled polycrystalline ferroelectric PZT ceramics for direct comparison with synchrotron X-ray measurements. The grains are modelled as spherical inclusions, to which transformation strains are assigned depending on the fractions of different ferroelectric domains. Eshelby's inclusion problem with the classical self-consistent method is applied to evaluate the elastic state of the grains. In particular, the elongation due to lattice elastic strain is calculated as a function of inclination Ψ relative to the polar axis. The ratio of diffraction peak intensities, corresponding to the domain fractions, is also expressed as a function of Ψ. This analysis identifies the special character of the reflection, for which the lattice strain along in the stress free state is independent of ferroelectric domain population and hence unaffected by poling. The elongation due to the lattice strain parallel to and peak intensity ratio are expressed in terms of the overall macroscopic strain of a poled specimen, each having a dependence.