首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 77 毫秒
1.
欧拉描述的大变形固结理论   总被引:10,自引:1,他引:9  
以往大变形固结理论主要基于一般的固体力学模型,其控制方程忽视了固结过程中排水引起 的质量变化. 提出饱和土的连续介质模型,并基于连续介质力学的公理体系推导了反映质量 变化的欧拉描述的大变形固结控制方程. 发现传统固结理论中:(1)忽视了渗流速度对土体平衡条件的影响;(2)决定土体平衡的总应力张量只有在土体变形速度和渗流速度方向相同时才具有对称性等. 在忽略变质量效应等条件下,传统理论成为本文理论的特例. 通过算例 的有限元分析,比较了欧拉描述与两种物质描述方法的差别,得到初步结论:(1)欧拉描述 方法计算的地基沉降量要小于物质描述方法的结果;(2)欧拉描述方法计算的侧向位移偏大 于两种物质描述结果.  相似文献   

2.
基于Gibson大变形固结理论,通过引入Hansbo渗流模型和软黏土非线性变形特性,同时考虑土层的沉积效应,分别建立了以孔隙比$e$和超孔压$u$表示的砂井地基大变形固结方程。通过与已有研究成果的对比,验证了本文方法的可靠性和砂井地基大变形固结方程两种描述方式的等效性。通过FlexPDE得到方程的数值解,在此基础上,研究了砂井地基大、小应变固结理论与Barron固结解的差异性,探讨了Hansbo渗流参数$m$和$I_1$对砂井地基固结的影响,最后对比分析了砂井地基轴对称固结、径向固结和竖向一维固结的关系。研究结果表明:考虑Hansbo渗流的砂井地基非线性大变形固结模型的固结速率最慢,且在固结后期,Hansbo渗流时大、小应变固结与Barron固结的平均固结度基本趋近;随着Hansbo渗流参数$m$和$I_1$的逐渐增大,砂井地基的固结速率逐渐降低;随着砂井影响半径的增大,砂井地基轴对称固结与径向固结的差异性也越来越大,且在固结早期会出现一维竖向固结速率高于轴对称固结和径向固结的现象。  相似文献   

3.
基于Gibson大变形固结理论,通过引入Hansbo渗流模型和软黏土非线性变形特性,同时考虑土层的沉积效应,分别建立了以孔隙比e和超孔压u表示的砂井地基大变形固结方程。通过与已有研究成果的对比,验证了本文方法的可靠性和砂井地基大变形固结方程两种描述方式的等效性。通过FlexPDE得到方程的数值解,在此基础上,研究了砂井地基大、小应变固结理论与Barron固结解的差异性,探讨了Hansbo渗流参数m和I1对砂井地基固结的影响,最后对比分析了砂井地基轴对称固结、径向固结和竖向一维固结的关系。研究结果表明:考虑Hansbo渗流的砂井地基非线性大变形固结模型的固结速率最慢,且在固结后期,Hansbo渗流时大、小应变固结与Barron固结的平均固结度基本趋近;随着Hansbo渗流参数m和I1的逐渐增大,砂井地基的固结速率逐渐降低;随着砂井影响半径的增大,砂井地基轴对称固结与径向固结的差异性也越来越大,且在固结早期会出现一维竖向固结速率高于轴对称固结和径向固结的现象。  相似文献   

4.
对多层地基的平面应变固结问题进行了研究,并同时考虑了土体的渗透各向异性和孔隙 流体的可压缩性. 从平面应变Biot固结的控制方程出发,对时间t, 坐标z和x进行 Laplace和Fourier变换,建立了地基表面(z=0)和任意深度z处的基本量 在Laplace-Fourier变换域内的传递矩阵关系. 利用传递矩阵 法,结合土层连续条件和边界条件,并应用Laplace-Fourier逆变换技术,推导出渗透各向 异性可压缩多层地基平面应变固结的理论解. 基于该解,编制了计算程序,并进行了 数值计算. 讨论了土体的渗透各向异性、孔隙流体的可压缩性以及地基的分层特性对地基固 结的影响,分析结果表明:土体的渗透各向异性、孔隙流体的可压缩性,以及地基的分层特 性对地基的固结行为有着重要的影响.  相似文献   

5.
考虑桩体内径向渗流的复合地基固结解   总被引:4,自引:0,他引:4  
考虑了桩体内径竖向组合渗流和涂抹区土体水平渗透系数的两种变化模式,得到了此类固结问题的控制方程.采用新的初始条件,得到了控制方程的解答,给出了桩周土体和桩体内的平均孔压.在此基础上,把桩体的固结压缩引人对复合地基总平均固结度的定义中,分别给出了复合地基按应力和按应变定义的总平均固结度.结果表明:按应力和按应变定义的复合地基的总平均固结度相等;考虑桩体内径向渗流比不考虑桩体内径向渗流的复合地基固结度要小,而且随着桩间距的增大,两者之间的差值逐渐减小;考虑涂抹区水平渗透系数逐渐变化比假定涂抹区水平渗透系数保持不变的复合地基的总平均固结度大.  相似文献   

6.
对多层地基的平面应变固结问题进行了研究,并同时考虑了土体的渗透各向异性和孔隙流体的可压缩性.从平而应变Biot固结的控制方程出发,对时间t,坐标z和x进行Laplace和Fourier变换,建立了地基表面(z=O)和任意深度z处的基本量在Laplauce-Fourier变换域内的传递矩阵关系.利用传递矩阵法,结合土层连续条件和边界条件,并应用Laplace-Fourier逆变换技术,推导出渗透各向异性可压缩多层地基平面应变固结的理论解.基于该解,编制了计算程序,并进行了数值计算.讨论了土体的渗透各向异性、孔隙流体的可压缩性以及地基的分层特性对地基同结的影响,分析结果表明:土体的渗透各向异性、孔隙流体的可压缩性,以及地基的分层特性对地基的固结行为有着重要的影响.  相似文献   

7.
针对复合地基固结问题,考虑井阻和土体径竖向渗流的影响,建立以"桩–土–桩"为单元的复合地基群井计算模型,采用解析解法,推导出瞬时载荷作用下复合地基群井固结解析解,讨论了复合地基固结特点和孔压等的变化规律。研究表明,复合地基群井固结模型为复合地基固结理论的研究提供了一种新思路,在井径比大于5时,基于中心桩、边桩流量相等假设,复合地基群井固结理论所求固结度和传统固结理论所求固结度相差很小,可忽略不计;桩体渗透系数、内外扰动区土体径向渗透系数、土体竖向渗透系数越大,复合地基固结速率越快;堆载越大,最终达到稳定时的沉降量和竖向应变越大;地基表层土体的孔压消散速率和竖向应变速率大于地基深部土体。  相似文献   

8.
针对复合地基固结问题,考虑井阻和土体径竖向渗流的影响,建立 以"桩-土-桩"为单元的复合地基群井计算模型,采用解析解法,推导出瞬时载荷作用下复合地基群井固结解析解,讨论了复合地基固结特点和孔压等的变化规律。研究表明,复合地基群井固结模型为复合地基固结理论的研究提供了一种新思路,在井径比大于5 时,基于中心桩、边桩流量相等假设,复合地基群井固结理论所求固结度和传统固结理论所求固结度相差很小,可忽略不计;桩体渗透系数、内外扰动区土体径向渗透系数、土体竖向渗透系数越大,复合地基固结速率越快;堆载越大,最终达到稳定时的沉降量和竖向应变越大;地基表层土体的孔压消散速率和竖向应变速率大于地基深部土体。  相似文献   

9.
基于三维有限元方法,提出了一个预测和评价砂井地基的简化计算模型。该计算模型采用块体单元模拟砂井周围的土体,用砂井单元模拟砂井的竖向排水和水平排水过程,并且推导了反映土体单元和砂井单元之间排水过程的连续性方程。克服了以往有限元法计算砂井地基时,需要将砂井和周围土体作均质化等价的缺点,并可用弹塑性模型反映砂井周围土体的非线性变形和强度特性。计算了单个砂井地基固结排水过程。通过和理论解的比较表明,用本文简化计算模型得到的结果和理论解比较接近。同时,还计算了日本某高速公路路基用砂井 堆载预压法处理的过程,通过分析表明,该简化模型能反映砂井地基的固结排水过程,可以应用于实际工程。  相似文献   

10.
通过建立考虑热渗效应和热流固耦合效应的饱和土体固结方程,研究了无限长圆柱热固结问题. 利用Fourier 和Laplace 变换及其逆变换,给出了热固结问题的解析解;然后对空间内无限长圆柱形热源问题进行研究,得到非等温条件下柱体周围饱和土体温度、孔隙水压力的近似解,并总结其规律,分析了热渗系数、固结系数对温度作用下土体固结的影响.  相似文献   

11.
研究了温度场中非保守功能梯度材料(FGM)圆板的非线性力学行为。基于经典板理论,推导了受非保守力作用的FGM圆板在温度场中的控制微分方程。采用打靶法分析了由陶瓷二氧化锆和金属钛合金两相材料组成的非保守FGM圆板在均匀和非均匀升温场中的非线性力学行为。给出了不同均匀升温和非均匀升温场下,FGM圆板在非保守载荷作用下的平衡路径和平衡构形。分析并讨论了均匀和非均匀升温、材料梯度指数对非保守圆板过屈曲和弯曲行为的影响。结果表明:温度场中,非保守FGM圆板发生弯曲而纯陶瓷圆板会发生过屈曲行为;当梯度指数p=2,非保守载荷q=52时,均匀升温场中非保守圆板的变形大于非均匀升温场中非保守圆板的变形。  相似文献   

12.
Side forces on slender bodies of revolution at medium to high angles of attack (AOA > 30°) has been known from a large number of investigations. Asymmetric vortex pairs over a slender body are believed to be the principle cause of the side forces. Under some flight conditions, this side force may be as large as the normal force acting on the slender body. In this paper, experimental results are presented for side force control on a cone-cylinder slender body by using microfabricated balloon actuators. The micro balloon actuators are made of polydimethylsiloxane (PDMS) elastomer by using micro molding techniques. They can be packaged on curve surfaces of a cone-cylinder slender body. As actuator is actuated, the micro balloon actuator inflates about 1.2 mm vertically, which is about 2.4% of the cylinder diameter D (=50 mm) of the cone-cylinder slender body. Micro balloon actuators are actuated at different roll angles of a cone-cylinder slender body. Aerodynamic force measurement results indicate the effects of micro balloon actuators vary at different actuation locations on the cone-cylinder slender body. The side forces can be significantly reduced if the actuators are actuated in the weak vortex side (the side corresponding to the asymmetric vortex which is far from the surface) and actuation angles are located at about 50–60° (the actuation angle here is measured from stagnation line of the incidence plane toward weak vortex side direction). Significant changes are noticed from the surface pressure, as well as leeside vortex flow field, measurement. Micro balloon actuators change nose shapes of the slender body which decide adverse-pressure-gradient values and directly influence the origin of the separation lines and characteristics of the separated vortices over the leeside surface.  相似文献   

13.
This research seeks to increase our understanding on the laminar-turbulent transition under an external body force. Direct numerical simulation by the spectral method with a weak formulation is used to solve the transient 3-D Navier-Stokes equations. Initial disturbances consist of the finite-amplitude 2-D Tollmien-Schlichting wave and two 3-D oblique waves. Competitions among different modes were computed during transition for different Richardson numbers.

It is found that the body force can modify the transition mechanism of flows between two vertical plates. The body force was found to hasten the formation of three-dimensional flow. A non-laminar flow induced by the body force may present when the background flow is still laminar.  相似文献   

14.
Combining Dual Reciprocity Method (DRM) with Hybrid Boundary Node Method (HBNM), the Dual Reciprocity Hybrid Boundary Node Method (DRHBNM) is developed for three-dimensional linear elasticity problems with body force. This method can be used to solve the elasticity problems with body force without domain integral, which is inevitable by HBNM. To demonstrate the versatility and the fast convergence of this method, some numerical examples of 3-D elasticity problems with body forces are examined. The computational results show that the present method is effective and can be widely applied in solving practical engineering problems.  相似文献   

15.
为了刀板切削过程中的受力满足最合理的设计准则,专用传感器设计须基于固定总体结构,对局部结构优化,以达到设计合理的目的。刀板切削时受到土体的阻力可分解为水平力和垂直力,多维力传感器测量了两个力的大小和对传感器产生的弯矩。刀板工作中,弯矩引起的正应力比垂直力引起的拉应力及水平力引起的切应力要大得多,因此特别设计了弹性体的局部结构使得三个应力值接近于同一量级。传感器的标定结果显示,输入输出有良好的线性关系,并且很好地消除了耦合效果。最终,将该传感器应用于土体切削测试并验证了其可靠性。  相似文献   

16.
自重体积力作用下弹性体位移与尺寸间非线性关系的推导   总被引:2,自引:0,他引:2  
徐嘉谟 《力学学报》1997,5(4):340-345
本文用相似理论推导了线弹性体在自重体积力作用下原型与模型间的位移关系式。根据对这个关系式讨论的结果, 以及对竖直立柱自重压缩问题的解析, 得到了位移与尺寸间的非线性关系。  相似文献   

17.
Summary The paper deals with numerical solutions of singular integral equations in stress concentration problems for longitudinal shear loading. The body force method is used to formulate the problem as a system of singular integral equations with Cauchy-type singularities, where unknown functions are densities of body forces distributed in the longitudinal direction of an infinite body. First, four kinds of fundamental density functions are introduced to satisfy completely the boundary conditions for an elliptical boundary in the range 0≤φ k ≤2π. To explain the idea of the fundamental densities, four kinds of equivalent auxiliary body force densities are defined in the range 0≤φ k ≤π/2, and necessary conditions that the densities must satisfy are described. Then, four kinds of fundamental density functions are explained as sample functions to satisfy the necessary conditions. Next, the unknown functions of the body force densities are approximated by a linear combination of the fundamental density functions and weight functions, which are unknown. Calculations are carried out for several arrangements of elliptical holes. It is found that the present method yields rapidly converging numerical results. The body force densities and stress distributions along the boundaries are shown in figures to demonstrate the accuracy of the present solutions. Received 26 May 1998; accepted for publication 27 November 1998  相似文献   

18.
内孤立波沿山脊地形传播过程中的结构变化使得影响海洋结构物及水下航行器安全的不确定因素增加,用大型重力式分层流试验水槽系统研究内孤立波过山脊地形及其对细长潜体作用力特性,可有效提高对其危害性机理的认识.为此,利用电导率探头阵列,结合染色标识方法,测量内孤立波演变特性,同时利用三分量传感器测量水下细长体模型受力特性.研究结果表明:山脊地形显著改变下凹型内孤立波结构,表现为坡前波幅增大,坡顶背风波面抬升,坡后波长变长;内波结构变化直接影响细长体受力特性,表现为坡前向下作用力明显增强,坡顶向上作用力突显,坡后作用力持续时间变长;细长体受力特性变化影响其运动趋势,坡前下沉运动增强、朝山脊方向纵荡运动显著.  相似文献   

19.
The concept of asynchronous oscillatory response of mechanical systems in free vibrations is addressed as an introduction to a definition of asynchronous modes of vibration. Connection of the asynchronous modes with the localization and other dynamical phenomena is discussed. Then, conditions for the occurrence of asynchronous modes are investigated in depth. It is seen that a non-conservative system, with an asymmetric stiffness matrix – caused, for instance, by circulatory loads, may have an asynchronous mode. Yet, it is also seen that non-conservativeness is not actually mandatory. Two- to four-degree-of-freedom models of a column with a follower force are addressed, allowing for a mathematical modelling and phenomenological discussion.  相似文献   

20.
This article investigates a method for obtaining all equilibrium configurations of a cantilever beam subjected to an end load with a constant angle of inclination. The formulation is based on plane finite-strain beam theory in the elastic domain. An example of a cantilever beam subjected to a horizontal pressure force is discussed in detail.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号