Condensation pressure drop of R22, R134a and R410A in a single circular microtube

The condensation pressure drop characteristics for pure refrigerants R22, R134a, and a binary refrigerant mixture R410A without lubricating oil in a single circular microtube were investigated experimentally. The test section consists of 1,220?mm length with horizontal copper tube of 3.38?mm outer diameter and 1.77?mm inner diameter. The experiments were conducted at refrigerant mass flux of 450–1,050?kg/m²s, and saturation temperature of 40°C. The main experimental results showed that the condensation pressure drop of R134a is higher than that of R22 and R410A for the same mass flux. The experimental data were compared against 14 two-phase pressure drop correlations. A new pressure drop model that is based on a superposition model for refrigerants condensing in the single circular tube is presented.     

Experimental study of in-tube cooling heat transfer and pressure drop characteristics of R134a at supercritical pressures

The in-tube cooling flow and heat transfer characteristics of R134a at supercritical pressures are measured experimentally for various pressures and mass fluxes in a horizontal tube. The tube is made of stainless steel with an inner diameter of 4.01 mm. Experiments are conducted for mass fluxes from 70 kg/m² s to 405 kg/m² s and pressures from 4.5 MPa to 5.5 MPa. The inlet refrigerant temperature is from 80 °C to 140 °C. The results show that the refrigerant temperature, the mass flux and the pressure all significantly affect the flow and heat transfer characteristics of R134a at supercritical pressures. The experimentally measured frictional pressure drop and heat transfer coefficient are compared with predicted results from several existing correlations. The comparisons show that the predicted frictional pressure drop using Petrov and Popov’s correlation accounting for the density and viscosity variations agree well with the measured data. Gnielinski’s correlation for the heat transfer coefficient agrees best with the measured data with deviations not exceeding 25%, while correlations based on supercritical CO₂ heat transfer data overcorrect for the influence of the thermophysical property variations resulting in larger deviations. A new empirical correlation is developed based on the measured results by modifying Gnielinski’s equation with thermophysical property terms including both the property variations from the inlet to the outlet of the entire test section and from the bulk to the wall. Most of the experimental data is predicted by the new correlation within a range of 15%.     

Experimental investigation of the flow pattern,pressure drop and void fraction of two-phase flow in the corrugated gap of a plate heat exchanger

The two-phase flow in the corrugated gap created by two adjacent plates of a plate heat exchanger was investigated experimentally. One setup consisting of a transparent corrugated gap was used to visualize the two-phase flow pattern and study the local phenomena of phase distribution, pressure drop and void fraction. Saturated two-phase R365mfc and an air-water mixture were used as working fluids.In a second experimental setup, the heat transfer coefficients and the pressure drop inside an industrial plate heat exchanger during the condensation process of R134a are determined. Both experimental setups use the same type of plates, so the experimental results can be connected and a flow pattern model for the condensation in plate heat exchangers can be derived. In this work the results of the flow pattern visualization, the two-phase pressure drop in the corrugated gap and the void fraction analysis by measurement of the electrical capacity are presented. A new pressure drop correlation is derived, which takes into account different flow patterns, that appear during condensation. The mean deviation of the presented pressure drop model compared to the experimental data and data from other experimental works is 18.9%. 81.7% of the calculated pressure drop lies within ±30% compared to the experimental data.     

Pressure drop prediction in annular two-phase flow in macroscale tubes and channels

A new prediction method for the frictional pressure drop in annular two-phase flow is presented. This new prediction method focuses on the aerodynamic interaction between the liquid film and the gas core in annular flows, and explicitly takes into account the asymmetric liquid film distribution in the tube cross section induced by the action of gravity in horizontal tubes operated at low mass fluxes. The underlying experimental database contains 6291 data points from the literature with 13 fluid combinations (both single-component saturated fluids such as water, carbon dioxide and refrigerants R12, R22, R134a, R245fa, R410a, R1234ze, and two-component fluids such as water-argon, water-nitrogen, alcohol-argon, water plus alcohol-argon and water-air), vertical and horizontal tubes and annuli with diameters from 3 mm to 25 mm, and both adiabatic and evaporating flow conditions. The new prediction method is very simple to implement and use, is physically based and outperforms existing pressure drop correlations (mean absolute error of 12.9%, and 7 points out of 10 captured to within ±15%).     

Heat transfer and enhancement analyses of flow boiling for R417A and R22

The experimental study on heat transfer of R417A and R22 flow boiling inside a horizontal smooth and two internally grooved tubes with different geometrical parameters was conducted. Based on the experimental results, evaporation heat transfer characteristics of R417A and R22 flowing in different tubes, the influence of micro-fin geometrical parameters, vapor quality and mass flux of refrigerants on heat transfer enhancement factors, and the difference of enhancement factors between R417A and R22 were analyzed and discussed. The result indicates: whether for R22 or for R417A, the enhancement effect of Tube III having the narrower distance between micro-fins excels than Tube II. The influence of vapor qualities and mass fluxes on enhancement factors for R417A is different from R22. And the difference of enhancement factors between R417A and R22 appears different cases at different vapor quality regions.     

Flow condensation heat transfer characteristics of hydrocarbon refrigerants and dimethyl ether inside a horizontal plain tube

Flow condensation heat transfer coefficients (HTCs) and pressure drop of R22, propylene, propane, DME and isobutane are measured on a horizontal plain tube. The main test section in the experimental flow loop is made of a plain copper tube of 8.8 mm inner diameter and 530 mm length. The refrigerant is cooled by passing cold water through the annulus surrounding the test section. Tests are performed at a fixed refrigerant saturation temperature of 40 ± 0.2 °C with mass fluxes of 100, 200, and 300 kg/m² s and heat flux of 7.3–7.7 kW/m². The heat transfer and pressure drop data are obtained in the vapor quality range of 10–90%. Test results show that for a given mass flux the flow condensation HTCs of propylene, propane, DME and isobutane are higher than those of R22 by up to 46.8%, 53.3%, 93.5% and 61.6%, respectively. Also well-known correlations developed based upon conventional fluorocarbon refrigerants predict the present data within a mean deviation of 33%. Finally, the pressure drop increases as the mass flux and quality increase and isobutane shows the highest pressure drop due to its lowest vapor pressure among the fluids tested.     

Experimental and numerical investigation on heat transfer characteristics of supercritical R1234ze(E) cooled in horizontal tubes

The heat transfer characteristics of supercritical fluids in tubes have been considered indispensable for the design and optimization of the heat exchanger and the energy conversion system. Specifically the cooling heat transfer of supercritical R1234ze(E) in horizontal tubes is a promising heat-power conversion technology; however, there is a scarcity of conducted research in available literature. The present work, the first-ever study in this direction, aims to thoroughly investigate the heat transfer characteristics of supercritical R1234ze(E) which is cooled in horizontal tubes. Experimental work was performed to thoroughly explore and inspect the heat transfer characteristics of supercritical R1234ze(E) passing through the tube of 4.12 mm diameter at 4–5 MPa pressure and 240–400 kg/m² s mass flux. Furthermore, the simulation study, supporting the experimental investigation under the same conditions of pressure and mass flux, extended the range of tube diameter up to 9.44 mm. The effects of pressure, mass flux and tube diameter on the heat transfer coefficient were carefully analyzed in the present research work. Based on the simulation results and experimental results, heat transfer correlations were newly developed by separating the region above and below the pseudo-critical temperature. The average absolute deviation between the calculated Nusselt numbers by the numerical correlation and the simulation results was found 2.87%; the average absolute deviation between the calculated Nusselt numbers by the experimental correlation and the experimental results was found 5.3%.     

Evaluation analysis of prediction methods for two-phase flow pressure drop in mini-channels

Two-thousand and ninety-two data of two-phase flow pressure drop were collected from 18 published papers of which the working fluids include R123, R134a, R22, R236ea, R245fa, R404a, R407C, R410a, R507, CO₂, water and air. The hydraulic diameter ranges from 0.506 to 12 mm; Re_l from 10 to 37,000, and Re_g from 3 to 4 × 10⁵. Eleven correlations and models for calculating the two-phase frictional pressure drop were evaluated based upon these data. The results show that the accuracy of the Lockhart–Martinelli method, Mishima and Hibiki correlation, Zhang and Mishima correlation and Lee and Mudawar correlation in the laminar region is very close to each other, while the Muller-Steinhagen and Heck correlation is the best among the evaluated correlations in the turbulent region. A modified Chisholm correlation was proposed, which is better than all of the evaluated correlations in the turbulent region and its mean relative error is about 29%. For refrigerants only, the new correlation and Muller-Steinhagen and Heck correlation are very close to each other and give better agreement than the other evaluated correlations.     

Boiling heat transfer,pressure drop,and flow pattern in a horizontal square minichannel

This study experimentally investigated the flow boiling heat transfer, pressure drop, and flow pattern in a horizontal square minichannel with a hydraulic diameter of 2.0 mm, and the effects of mass flux, vapor quality, heat flux, and refrigerant properties on the flow boiling characteristics were clarified. The heat transfer coefficient and pressure drop of R32 and R1234yf were measured in a mass flux range of 50–400 kgm⁻²s⁻¹ at a saturation temperature of 15 °C. The flow pattern of the square minichannel outlet was observed and was classified as plug, wavy, churn, and annular flows. The heat transfer coefficients in the square minichannel were larger than those in the circular minichannel with a similar hydraulic diameter at low mass flux conditions. The heat transfer coefficients of R32 indicated higher values compared with those of R1234yf at same mass flux and qualities. An empirical heat transfer model taking into account the forced convection, nucleate boiling, and thin liquid film evaporation was developed for horizontal square and circular minichannels. The frictional pressure drop of R32 was 1.5–2 times higher than that of R1234yf at same mass flux and vapor quality condition, and the effect of channel shape on the frictional pressure drop was small unlike the boiling heat transfer.     

Heat transfer,pressure drop and flow patterns during flow boiling of R407C in a horizontal microfin tube

The heat transfer, pressure drop and flow patterns during flow boiling of R407C in a horizontal microfin tube have been investigated. The microfin tube is made of copper with a total fin number of 55 and a helix angle of 15°. The fin height is 0.24 mm and the inner tube diameter at fin root is 8.95 mm. The test tube is 1 m long. It is heated electrically. The experiments have been performed at saturation temperatures between −30°C and +10°C. The mass flux was varied between 25 and 300 kg/m²/s, the heat flux from 20,000 W/m² down to 1,000 W/m². The vapour quality was kept constant at 0.1, 0.3, 0.5, 0.7 at the inlet and 0.8, 1.0 at the outlet, respectively. The measured heat transfer coefficient is compared with the correlations of Cavallini et al., Shah as well as Zhang et al. Cavallini’s correlation contains seven experimental constants. After fitting these constants to our measured values, the correlation achieves good agreement. The measured pressure drop is compared to the correlations of Pierre, Kuo and Wang as well as Müller-Steinhagen and Heck. The best agreement is achieved with the correlation of Kuo and Wang. Almost all values are calculated within an accuracy of ±30%. The flow regimes were observed. It is shown, that changes in the flow regime affect the heat transfer coefficient significantly.     

Two-phase flow of refrigerants in 85 μm-wide multi-microchannels: Part I – Pressure drop

This article is the first part of a study on flow boiling of R236fa and R245fa. This part presents pressure drop measurements obtained on a silicon multi-microchannel evaporator with 85 μm wide and 560 μm high channels separated by 46 μm wide fins. The 135 microchannels were 12.7 mm long. Dielectric refrigerants R236fa and R245fa were used as the evaporating test fluids. The inlet saturation temperature was maintained at 30.5 °C while the mass fluxes were varied from 499 to 1100 kg/m² s and the base heat flux was tested from 130 to 1400 kW/m². A new experimental technique was developed to measure the outlet pressure losses, which represented up to 30% of the total pressure drop and thus cannot be neglected. The microchannel pressure drop measurements were very well predicted by the method of Cioncolini et al. (2009).     

Low-GWP refrigerants flow boiling heat transfer in a 5 PPI copper foam

This paper reports an experimental investigation of the heat transfer performance of the new low-GWP refrigerants, R1234yf and R1234ze(E), during flow boiling heat transfer inside a horizontal high porosity copper foam with 5 Pores Per Inch (PPI). Metal foams are a class of cellular structured materials consisting of a stochastic distribution of interconnected pores; these materials have been proposed as effective solutions for heat transfer enhancement during both single and two-phase heat transfer. R1234yf and R1234ze(E) refrigerants are appealing alternatives of the more traditional R134a by virtue of their negligible values of GWP and normal boiling temperatures close to that of R134a, which make them suitable solution in several different applications, such as: refrigeration and air conditioning and electronic thermal management. This work compares the two-phase heat transfer behaviour of these new HFO refrigerants, studying the boiling process inside a porous medium and permitting to understand their effective heat transfer capabilities. The experimental measurements were carried out by imposing three different heat fluxes: 50, 75, and 100 kW m⁻², at a constant saturation temperature of 30 °C; the refrigerant mass velocity was varied between 50 and 200 kg m⁻² s⁻¹, whilst the mean vapour quality varied from 0.2 to 0.95. The two-phase heat transfer and pressure drop performance of the two new HFO refrigerants is compared against that of the more traditional R134a.     

Flow pattern,void fraction and pressure drop of refrigerant two-phase flow in a horizontal pipe—I. Experimental data

Experiments with refrigerant two-phase flow in a horizontal pipe have been performed and data on flow pattern, void fraction and pressure drop have been obtained. Refrigerants used were R12 and R22, and the range of saturation pressure was from 5.7 to 19.6 bar.In this paper, the experimental equipment and procedure are described in detail, and the data are both tabulated and presented graphically.     

Theoretical analysis of pressure-drop type instabilities in an upflow boiling system with an exit restriction

 In this work, two-phase flow pressure-drop type instabilities in an upflow boiling system are studied theoretically. Dynamic simulations of the pressure-drop type instabilities require the knowledge of the steady state characteristics of the system in terms of the pressure drop versus the mass flow rate. In a boiling system with an exit restriction at the outlet of the boiling channel, the pressure drop through the system concentrates at the exit restriction. Therefore, the correlation of the pressure drop of the two-phase mixture flowing through the exit restriction (i.e. a sharp-edged orifice) is essential in the calculation of the total pressure drop of the system. A model for the exit restriction is developed and compared with the experimental results covering a wide range of vapor quality with different heat inputs and inlet subcoolings. The drift-flux model is adopted to predict the steady state characteristics of the boiling system. The dynamic oscillations of the quasi-static pressure-drop type instabilities in the boiling system are simulated and good predictions of the system stability boundary and oscillatory characteristics are obtained when compared with the experimental results. Received on 4 May 2000     

Freon R141b flow boiling in silicon microchannel heat sinks: experimental investigation

This paper presents experimental investigations on Freon R141b flow boiling in rectangular microchannel heat sinks. The main aim is to provide an appropriate working fluid for microchannel flow boiling to meet the cooling demand of high power electronic devices. The microchannel heat sink used in this work contains 50 parallel channels, with a 60 × 200 (W × H) μm cross-section. The flow boiling heat transfer experiments are performed with R141b over mass velocities ranging from 400 to 980 kg/(m² s) and heat flux from 40 to 700 kW/m², and the outlet pressure satisfying the atmospheric condition. The fluid flow-rate, fluid inlet/outlet temperature, wall temperature, and pressure drop are measured. The results indicate that the mean heat transfer coefficient of R141b flow boiling in present microchannel heat sinks depends heavily on mass velocity and heat flux and can be predicted by Kandlikar’s correlation (Heat Transf Eng 25(3):86–93, 2004). The two-phase pressure drop keeps increasing as mass velocity and exit vapor quality rise.     

Single-beam gamma densitometry measurements of oil–water flow in horizontal and slightly inclined pipes

Gamma densitometry is a frequently used non-intrusive method for measuring component volume fractions in multiphase flow systems. The application of a single-beam gamma densitometer to investigate oil–water flow in horizontal and slightly inclined pipes is presented. The experiments are performed in a 15 m long, 56 mm diameter, inclinable stainless steel pipe using Exxsol D60 oil (viscosity 1.64 mPa s, density 790 kg/m³) and water (viscosity 1.0 mPa s, density 996 kg/m³) as test fluids. The test pipe inclination is changed in the range from 5° upward to 5° downward. Experimental measurements are reported at three different mixture velocities, 0.25, 0.50 and 1.00 m/s, and the inlet water cut is varied from 0 to 1. The gamma densitometer is composed of radioactive isotope of Am-241 with the emission energy of 59.5 keV, scintillation detector [NaI(Tl)] and signal processing system. The time averaged cross-sectional distributions of oil and water phases are measured by traversing the gamma densitometer along the vertical pipe diameter. Based on water volume fraction measurements, water hold-up and slip ratio are estimated. The total pressure drop over the test section is measured and frictional pressure drop is estimated based on water hold-up measurements. The measurement uncertainties associated with gamma densitometry are also discussed. The measured water hold-up and slip ratio profiles are strongly dependent on pipe inclination. In general, higher water hold-up values are observed in upwardly inclined pipes compared to the horizontal and downwardly inclined pipes. At low mixture velocities, the slip ratio decreases as the water cut increases. The decrease is more significant as the degree of inclination increases. The frictional pressure drop for upward flow is slightly higher than the horizontal flow. In general, there is a marginal difference in frictional pressure drop values for horizontal and downwardly inclined flows.     

A Semi-empirical Correlation for Pressure Drop in Packed Beds of Spherical Particles

The effect of a confining wall on the pressure drop of fluid flow through packed beds of spherical particles with small bed-to-particle diameter ratios was investigated to develop an improved pressure drop correlation. The dependency of pressure loss on both wall friction and increased porosity near the wall was accounted for by using a theoretical approach. A semi-empirical model was created based upon the capillary-orifice model, which included a wall correction factor for the inertial pressure loss. In this model, packed beds were treated as a bundle of capillary tubes whose orifice diameter in the core region was different from that of the wall region. Using this model, a new pressure drop correlation was obtained, based on the Ergun equation and applicable for a wide range of Reynolds numbers (10⁻²–10³). The proposed correlation was compared with previous correlations, as well as with experimental data. This correlation showed close agreement with the experimental data for both low- and high-Reynolds number regimes and for a wide range of bed-to-particle diameter ratios. The ratio of the pressure drop in finite packing to that in homogeneous packing was then calculated. This ratio clearly shows how the wall effect depends on the Reynolds number and the bed-to-particle diameter ratio.     

Experimental study on condensation heat transfer in vertical minichannels for new refrigerant R1234ze(E) versus R134a and R236fa

Experimental condensation heat transfer data for the new refrigerant R1234ze(E), trans-1,3,3,3-tetrafluoropropene, are presented and compared with refrigerants R134a and R236fa for a vertically aligned, aluminum multi-port tube. Local condensation heat transfer measurements with such a multi-microchannel test section are very challenging due to the large uncertainties related to the heat flux estimation. Presently, a new experimental test facility was designed with a test section to directly measure the wall temperature along a vertically aligned aluminum multi-port tube with rectangular channels of 1.45 mm hydraulic diameter. Then, a new data reduction process was developed to compute the local condensation heat transfer coefficients accounting for the non-uniform distribution of the local heat flux along the channels. The condensation heat transfer coefficients showed the expected decrease as the vapor quality decreased (1.0-0.0) during the condensation process, as the mass velocity decreased (260-50 kg m⁻² s⁻¹) and as the saturation temperature increased (25-70 °C). However, the heat transfer coefficients were not affected by the condensing heat flux (1-62 kW m⁻²) or by the entrance conditions within the tested range. It was found that the heat transfer performance of R1234ze(E) was about 15-25% lower than for R134a but relatively similar to R236fa. The experimental data were then compared with leading prediction methods from the literature for horizontal channels. In general, the agreement was poor, over-predicting the high Nusselt number data and under-predicting the low Nusselt number data, but capturing the mid-range quite well. A modified correlation was developed and yielded a good agreement with the current database for all three fluids over a wide range of operating conditions.     

Flow of Newtonian and Non-Newtonian Fluids Through Packed Beds: An Experimental Study

The phenomena of flow reduction and flow enhancement was observed in case of viscoelastic and viscoinelastic fluids flowing through packed beds, respectively. In this study, the pressure drop-flow rate behaviors for the flow of Newtonian (water), non-Newtonian viscoinelastic (Carboxy methyl cellulose solution in water, CMC) and viscoelastic (Polyacrylamide solution in water, PAA) fluids have been experimentally studied and pressure drop behavior compared with existing models for viscoinelastic and viscoelastic fluids. Based on the observed data, an appropriate empirical correlation for pressure drop prediction in case of non-Newtonian fluid flowing through packed bed has been proposed. The correlation predicts the data well to within a reasonable accuracy.     

Flow boiling of halogenated refrigerants at high saturation temperature in a horizontal smooth tube

Several correlations are available in the open literature for computing the heat transfer coefficient during flow boiling inside plain channels. With respect to halogenated refrigerants, these correlations are usually compared to data taken in a limited range of evaporation temperature and reduced pressure. More recently, the adoption of new refrigerants, such as high pressure HFCs and carbon dioxide, requires to largely extend the pressure range of application of such correlations. Besides, the design of evaporators for some heat pumping applications, where temperatures are set at higher values as compared to usual evaporating temperatures in air-conditioning equipment, requires proper validation of the computing methods.The present paper aims at comparing four well-known predicting models to a new database collected during flow boiling of HCFC (R22) and HFC refrigerants (R134a, R125 and R410A) in a horizontal 8 mm internal diameter tube. This database is characterized by saturation temperature ranging between 25 °C and 45 °C, reduced pressure spanning between 0.19 and 0.53. Mass velocity ranges between 200 and 600 kg m^?2 s^?1 and heat flux between 9 and 53 kW m^?2.Evaporating heat transfer coefficients of halogenated refrigerants at such high temperatures have not been reported in the open literature so far. The discussion of the results will enlighten some similarities with experimental trends presented in the literature for evaporating carbon dioxide.Two models tested here show good prediction capabilities of the present experimental data, but not for all the data sets in the same way. For the purpose of practical use, a simple modification of the correlation by Gungor and Winterton [1] is proposed, showing that this is able to catch the experimental trends of the present database with good agreement.