曲壁蜂窝夹层板的振动特性研究

曲壁蜂窝具有负刚度特性,可以在大变形过程中吸收能量、抗冲击,并且在冲击过后可以自我恢复而不像传统蜂窝被压溃。本文将曲梁构成的负刚度蜂窝作为芯层,建立夹层板的动力学模型;推导出了曲壁负刚度蜂窝胞元的等效弹性参数,将其周期性排列为蜂窝芯,应用Reddy高阶剪切变形理论、Von-Karman大变形关系和Hamilton原理推导了负刚度蜂窝夹层板的非线性动力学方程;应用Navier法计算了四边简支边界条件下的固有频率。并利用有限元软件ABAQUS建立模型,计算固有频率,与理论计算结果进行比较,结果显示二者的计算结果具有较好的一致性,验证了芯层等效弹性参数及模型的有效性。探讨了在蜂窝胞元具有较高吸能情形下,夹层板在不同芯层厚度、不同芯厚比以及不同胞元曲壁厚度时的固有频率的变化特性。     

蜂窝层芯夹层板结构振动与传声特性研究

蜂窝层芯夹层板应用于飞行器、高速列车等交通工具的主体及底板结构时需要考虑其振动及隔声特性. 针对声压激励下的四边简支蜂窝层芯夹层板结构,应用基于Reissner夹层板理论的结构振动方程建立了的声振耦合理论模型(声压以简支模态双级数的形式引入振动控制方程),结合流固耦合条件求解了声振耦合系统控制方程,应用有限元模拟对理论预测进行了验证. 基于理论模型的数值计算结果,系统研究了蜂窝层芯夹层板结构的振动特性和传声特性,刻画了层芯厚度、蜂窝壁厚、夹层板面内尺寸和声压入射角度等关键系统参数对夹层板振动和传声特性的影响,为此类结构的工程优化设计提供了必要的理论参考.     

负泊松比蜂窝夹层板的振动特性研究

研究了负泊松比蜂窝夹层板几何参数变化对板振动频率的影响,并得到了频率随泊松比的变化规律。在Reddy高阶剪切变形理论的基础上,利用Hamilton原理,推导出四边简支边界条件下的负泊松比蜂窝夹层板的偏微分运动方程。根据修正后的Gibson公式,考虑了蜂窝胞元壁板的弯曲和伸缩变形,重新计算了蜂窝芯层胞元的等效弹性参数。利用Navier法,选择合适四边简支边界条件的模态函数,得出板的长厚比分别为0.01、0.05、0.10,芯厚比分别为0.80、0.85、0.90、0.95和蜂窝芯胞元倾角分别为-30°、-60°、0°、30°、60°等情况下系统的前五阶固有频率。研究结果表明,系统的固有频率随板的芯厚比、蜂窝芯胞元倾角、蜂窝芯壁厚与斜壁之比的增加都在减小,而随着板长厚比的增加而增加。分析了泊松比的变化对系统固有频率的影响,发现负泊松比蜂窝夹层板的固有频率要明显小于传统正泊松比蜂窝夹层板。本文所得结果对进一步研究系统的多模态共振具有指导意义,为负泊松比蜂窝夹层结构的工程应用在减振设计方面提供一定的理论依据。     

中厚矩形板的非线性动力屈曲分叉

建立考虑横向剪切与转动惯量影响的矩形板的动力控制方程，应用Ｇａｌｅｒｋｉｎ方法将其化为Ｍａｔｈｉｅｕ方程，然后根据Ｌｙａｐｕｎｏｖ－Ｓｃｈｍｉｄｔ方法得到了系统在参数激励下的１／２亚谐分叉特性，并给出了四边简支与四边固支弹性薄板的非线性动力屈曲分叉条件。     

四边简支正交各向异性蜂窝型夹层板固有频率计算

该文以四边简支的方形蜂窝矩形夹层板为例,在经典夹层板理论的基础上,运用离散结构形式的运动控制方程和线性微分算子的可交换性,给出了一种把具有蜂窝型夹心的夹层板的包含三个广义位移的控制方程组化为,仅包含一个广义位移函数的单一方程的简单方法,并给出了四边简支蜂窝型夹层板的固有频率的精确解。研究结果对蜂窝夹层板的结构设计和工程应用具有指导意义。     

轻质金属点阵夹层板热屈曲临界温度分析

本文针对均匀温度场下四边简支和四边固支金属点阵夹层板的临界热屈曲温度进行了求解和参数影响分析。将点阵夹芯等效为均匀连续体,并且将夹层板的剪切刚度近似为点阵夹芯的抗剪切刚度,忽略夹芯的抗弯刚度且认为夹层板主要由面板来提供抗弯刚度。对于无法获得解析解的四边固支条件,通过对未知变量进行双傅里叶展开的方法求解了Ressiner夹层板模型的临界屈曲温度,理论分析结果与有限元计算结果吻合良好。进一步分析了不同边界条件、点阵胞元构型、点阵材料相对密度、面板厚度等对临界屈曲温度的影响规律。     

内桁架-聚氨酯泡沫塑料夹层板简化力学模型

通过横向刚度等效的原则，将内桁架一聚氨酯泡沫塑料夹层板转变成半连续化模型，并通过其刚度常数的推导，使其转变成正交各向异性的夹层板，通过Livbove—Batdorf夹层板理论，得到其基本方程。并就简支板为例，得到其解析解，通过与有限元分析进行对比，两者结果吻合良好。最后就夹层板的力学特性进行了参数分析，讨论了钢筋支撑的最优布置方式，以及剪切刚度对板的变形的重要影响。     

考虑芯层离散特性的方形蜂窝夹层板自由振动分析

针对方形蜂窝夹层板,考虑其离散的芯层结构形式,在经典夹层板理论的基础上,运用Hamilton变分原理导出了其离散结构形式的运动控制方程.该文以四边简支的方形蜂窝矩形夹层板为例,采用傅立叶级数和伽辽金法求解出夹层板固有频率的半解析解,并与有限元仿真结果进行了比较,两者吻合良好.该文还将夹层板与等质量的实体板固有频率进行了比较,讨论了夹层板芯层薄壁间距、厚度、高度以及面板厚度对其固有频率的影响.计算结果表明,夹层板相对实体板具有很大的刚度;芯层薄壁高度相对其它参数对夹层板固有频率的影响更大.     

硬夹心矩形夹层板的整体稳定性分析

摘要：本文在Reissner型理论给出的位移模式基础上,修正其软夹心假设,考虑夹心层面内刚度,给出了硬夹心夹层板的几何方程、物理方程,建立了硬夹心夹层板结构在面内纵向载荷作用下的平衡微分方程,并对方程进行了简化,通过理论计算得到了四边简支条件下硬夹心矩形夹层板整体失稳临界载荷的解析解,并分别计算了夹心层材料的弹性模量 、厚度 、泊松比 对硬夹心夹层板临界载荷的影响,结果证明,对于硬夹心夹层结构,夹心层面内刚度对硬夹心夹层板整体失稳临界载荷的影响较大,考虑其面内刚度是必要的。     

具脱层的轴对称层合圆板的非线性振动分析

基于Von Karman板理论,应用三分区模型,建立了考虑横向剪切效应时具任意脱层的正交对称铺设轴对称层合圆板在径向压力荷载作用下的非线性运动微分方程。对未知变量在空间上采用Bessel函数,应用Galerkin法,得到无量纲的仅关于时间函数的运动微分方程,并应用谐波平衡法对此方程进行求解,算例中讨论了不同脱层半径、脱层深度对具脱层的正交对称铺设轴对称层合圆板非线性幅频响应的影响。     

Nonlinear dynamics of axially moving beam with coupled longitudinal–transversal vibrations

In this study, the nonlinear vibrations of an axially moving beam are investigated by considering the coupling of the longitudinal and transversal motion. The Galerkin method is used to truncate the governing partial differential equations into a set of coupled nonlinear ordinary differential equations. By detuning the axially velocity, the exact parameters with which the system may turn to internal resonance are detected. The method of multiple scales is applied to the governing equations to study the nonlinear dynamics of the steady-state response caused by the internal–external resonance. The saturation and jump phenomena of such system have been reported by investigating the nonlinear amplitude–response curves with respect to external excitation, internal, and external detuning parameters. The longitudinal external excitation may trigger only longitudinal response when excitation amplitude is weak. However, beyond the critical excitation amplitude, the response energy will be transferred from the longitudinal motion to the transversal motion even the excitation is employed on the longitudinal direction. Such energy transfer due to saturation has the potential to be used in the vibration suppression.     

Analysis and active control of nonlinear vibration of composite lattice sandwich plates

This paper is devoted to investigate the nonlinear vibration characteristics and active control of composite lattice sandwich plates using piezoelectric actuator and sensor. Three types of the sandwich plates with pyramidal, tetrahedral and Kagome cores are considered. In the structural modeling, the von Kármán large deflection theory is applied to establish the strain–displacement relations. The nonlinear equations of motion of the structures are derived by Hamilton’s principle with the assumed mode method. The nonlinear free and forced vibration responses of the lattice sandwich plates are calculated. The velocity feedback control (VFC) and H_∞ control methods are applied to design the controller. The nonlinear vibration responses of the sandwich plates with pyramidal, tetrahedral and Kagome cores are compared. The influences of the ply angle of the laminated face sheets, the thicknesses of the lattice core and face sheets and the excitation amplitude on the nonlinear vibration behaviors of the sandwich plates are investigated. The correctness of the H_∞ control algorithm is verified by comparing with the experiment results reported in the literature. The controlled nonlinear vibration response of the sandwich plate is computed and compared with that of the uncontrolled structural system. Numerical results indicate that the VFC and H_∞ control methods can effectively suppress the large amplitude vibration of the composite lattice sandwich plates.

     

Nonlinear dynamic response of a functionally graded plate with a through-width surface crack

A nonlinear vibration analysis of a simply supported functionally graded rectangular plate with a through-width surface crack is presented in this paper. The plate is subjected to a transverse excitation force. Material properties are graded in the thickness direction according to exponential distributions. The cracked plate is treated as an assembly of two sub-plates connected by a rotational spring at the cracked section whose stiffness is calculated through stress intensity factor. Based on Reddy’s third-order shear deformation plate theory, the nonlinear governing equations of motion for the FGM plate are derived by using the Hamilton’s principle. The deflection of each sub-plate is assumed to be a combination of the first two mode shape functions with unknown constants to be determined from boundary and compatibility conditions. The Galerkin’s method is then utilized to convert the governing equations to a two-degree-of-freedom nonlinear system including quadratic and cubic nonlinear terms under the external excitation, which is numerically solved to obtain the nonlinear responses of cracked FGM rectangular plates. The influences of material property gradient, crack depth, crack location and plate thickness ratio on the vibration frequencies and transient response of the surface-racked FGM plate are discussed in detail through a parametric study.     

Damping for large-amplitude vibrations of plates and curved panels,Part 1: Modeling and experiments

Theoretical and experimental non-linear vibrations of thin rectangular plates and curved panels subjected to out-of-plane harmonic excitation are investigated. Experiments have been performed on isotropic and laminated sandwich plates and panels with supported and free boundary conditions. A sophisticated measuring technique has been developed to characterize the non-linear behavior experimentally by using a Laser Doppler Vibrometer and a stepped-sine testing procedure. The theoretical approach is based on Donnell's non-linear shell theory (since the tested plates are very thin) but retaining in-plane inertia, taking into account the effect of geometric imperfections. A unified energy approach has been utilized to obtain the discretized non-linear equations of motion by using the linear natural modes of vibration. Moreover, a pseudo arc-length continuation and collocation scheme has been used to obtain the periodic solutions and perform bifurcation analysis. Comparisons between numerical simulations and the experiments show good qualitative and quantitative agreement. It is found that, in order to simulate large-amplitude vibrations, a damping value much larger than the linear modal damping should be considered. This indicates a very large and non-linear increase of damping with the increase of the excitation and vibration amplitude for plates and curved panels with different shape, boundary conditions and materials.     

Transversal forced vibrations of an axially moving sandwich belt system

Based on the author’s previously published results for transversal free vibrations of axially moving sandwich belts described by coupled partial differential equations, which are derived and analytically solved, this paper contains new analytical results, for forced vibrations of the same system excited by transversal external excitation. The transversal forced vibrations of the axially moving sandwich belts are described by the coupled partial nonhomogeneous differential equations. The partial differential equations are analytically solved. Bernoulli’s method of particular integrals and Lagrange’s method of the variations of the constants are used.     

静载荷对夹层圆板超谐波共振的影响

研究静载荷作用下夹层圆板的超谐波共振问题．基于Hoff型夹层板理论,给出了静载荷作用下夹层圆板的非线性动力学方程．应用Galerkin法推导了静载荷作用下夹层圆板的轴对称非线性振动方程．运用多尺度法分别对系统的三次超谐波问题和二次超谐波问题进行了求解,并依据Lyapunov稳定性理论得到了系统稳态运动的稳定性判据．通过算例,得到了周边简支约束下夹层圆板三次超谐波共振和二次超谐波共振的幅频响应曲线图、振幅-静载荷响应曲线图、振幅-激励力幅值响应曲线图;研究了不同参数对系统振幅的影响规律,并对解的稳定性进行了分析．     

Vibration reduction of multi-parametric excited spring pendulum via a transversally tuned absorber

The use of passive control strategy is a common way to stabilize and control dangerous vibrations in a nonlinear spring pendulum which is describing the ship’s roll motion. In this paper, a tuned absorber in the transversal direction is connected to a spring pendulum with multi-parametric excitation forces to control the vibration due to some resonance cases on the system. The method of multiple scale perturbation technique (MSPT) is applied to study the periodic solution of the given system near simultaneous sub-harmonic and internal resonance case. The stability of the steady-state solution near the resonance case is investigated and studied using frequency response equations. The effects of the absorber and some system parameters on the vibrating system are studied numerically. Optimal working conditions of the system are extracted when applying passive control methods. Comparison with the available published work is reported.