不同围压下C60混凝土三轴压缩过程能量分析

针对复杂应力状态下高强混凝土受压变形破坏过程中的能量演化机制问题,开展不同围压下C60高强混凝土试样三轴压缩试验,分析其在受力全过程中的变形与破坏特征。根据试验结果,探究了不同围压下高强混凝土三轴压缩过程能量演化机制。研究结果表明:围压越大,混凝土试样破坏时,其峰值应力与峰值应力对应的轴向应变越大,破坏形式由张拉破坏向剪切破坏过渡;峰值应力前,混凝土试样主要以弹性应变能储存为主,峰值应力对应的输入能密度和耗散能密度均随围压的增大而增大,且均与围压满足指数函数关系,其形状改变系数FX与轴向应力呈正比关系,体积改变系数FV与轴向应力呈反比关系;达到峰值应力时,体积改变系数FV小于形状改变系数FX;峰值应力后,主要以弹性应变能释放为主,并随着混凝土试样的破坏转化为各种形式的能量耗散。研究结果可为今后从能量角度研究高强混凝土本构关系提供有益参考。     

三种红层岩石常规三轴压缩下的强度与变形特性研究

利用MTS815Teststar程控伺服岩石力学试验系统研究了川东地区一红层边坡中的砂岩、粉砂岩和泥岩围压为0³MPa的应力-应变全过程曲线,建立了峰值强度、峰值强度前弹性模量以及峰值强度后的弹性模量和围压的关系。将低围压下红层的全应力-应变曲线概化成5个阶段,分别为压密段、弹性段、屈服段、应变软化段和塑性流动阶段。试验结果得出,红层弹性模量随围压的增加而提高且变化明显,砂岩和粉砂岩在此围压内为脆性破坏,泥岩为塑性破坏的规律。     

考虑围压效应的冻结砂土动态本构模型研究

为描述主动围压作用下冻结砂土的动态力学特性，通过在朱-王-唐模型的非线性体上串联塑性体，建立了能够考虑围压效应的冻结砂土动态损伤本构模型；分析了损伤参数对应力-应变曲线特征、屈服点、峰值应力和峰值应变的影响规律，基于冻结砂土动力学试验数据确定了模型参数；通过将模型和试验数据进行对比，并对不同试验条件下模型的预测误差进行分析，验证了模型的适用性和准确性。结果表明，损伤参数对应力-应变曲线弹性阶段和屈服点无明显影响，而对塑性阶段和破坏阶段的影响较为显著，本构模型预测的应力-应变曲线与试验结果具有较好的一致性。模型能够预测围压引起冻结砂土塑性阶段占比大和屈服点明显的特征，且能够描述围压对冻结砂土动态强度的增强效应；不同负温和主动围压条件下，模型对峰值应力和屈服强度的预测效果优于峰值应变和屈服应变。     

基于图形测量技术的煤岩力学三轴试验研究

为研究初始围压对煤岩力学特性的影响，以王庄煤矿9105工作面煤体为研究对象，通过HC-SPT-100型高压三轴试验机、HC-U7型非金属超声波探测仪、4K科研相机等仪器，利用数字图像测量技术开展不同初始围压下原煤试件加载试验，探究不同围压对煤体弹性模量、峰值应变、残余应力和破坏裂隙的影响规律，研究结果表明：弹性模量、峰值应变和残余应力随围压的增大而增大；随围压的增大各峰值应变增长速率不同，轴向峰值应变增长速率最快，体峰值应变增长速率次之，径向峰值应变增长速率最慢；不同围压加载破坏下煤体裂隙特征明显，主要以斜交裂隙为主；采用Jaeger法求得不同围压下煤岩体破坏临界强度值与试验值比较误差较小，符合Jaeger单结构面理论．     

加载速率影响的单裂隙类岩石试样能量演化规律

为了研究加载速率对单裂隙类岩石试样破坏过程中能量演化进程的影响规律,分析裂隙类岩石试样在不同加载速率下的能量响应特征,以预埋金属薄片方法制作的裂隙类岩石试件为研究对象,基于RMT-150B对单裂隙类岩石试样进行四级加载速率下的单轴压缩试验,获得四级加载速率下裂隙类岩石试样力学性能。试验结果表明:单裂隙类岩石试样峰值强度与加载速率呈正相关性,但增长速率随加载速率的增加而减小;当加载速度不断增大时,峰值处试样弹性应变能积聚能力增强,但是耗散应变能随加载速率的增大而逐渐减小;裂隙试样在峰值后会累积弹性应变能,但其积聚能力随加载速率的增大而有所削弱;裂隙试样耗散应变能转化速率在峰值前处于较低水平,在峰值后伴随宏观破裂面的贯通而骤增,表明单裂隙类岩石试样内部能量演化进程与其破坏规律之间具有内在联系。     

动力荷载对围压卸载下岩石动态变形模量的影响

利用SHPB岩石动静组合加载实验系统,研究在不同轴压水平下围压以1 MPa/s速率卸载至预加值50%时矽卡岩受频繁冲击作用的动态变形模量变化规律。实验结果表明:高轴压促使岩石内部微裂纹萌发与扩展,降低了岩石抵抗外部冲击的能力。围压的侧向约束阻碍岩石内部裂纹的横向扩展,但在围压卸载时会加剧岩石内部的损伤,这是由于高轴压下,围压卸载导致岩石内部应力重新分布。轴压与围压卸载共同影响着冲击作用下的岩石动态变形模量,通过岩样在冲击荷载下的能量耗散分析岩石动态变形模量的变化规律,有助于了解深部岩体开挖的破坏机制。     

花岗岩的加载速率效应及能量机制研究

加载速率对岩石的力学性质以及变形破坏方式具有重要的影响。基于MTS810电液伺服材料试验系统与PCI-2声发射仪对岩样进行不同加载速率作用下的单轴压缩和声发射试验。研究结果表明：（1）在各级加载速率作用下,岩样单轴压缩应力-应变曲线大致经历了压密、弹性、屈服、破坏四个阶段。岩样峰后曲线在加载速率为0.001~0.01 mm/s时出现台阶型分段跌落状,在加载速率为0.01~0.1 mm/s时呈现光滑、陡峭的连续曲线。（2）岩样峰值强度、弹性模量随加载速率的增加而增大,与加载速率对数均呈现三次多项式拟合关系。峰值应变随加载速率的增加而减小,与加载速率对数呈现线性拟合关系。（3）随着加载速率由0.001mm/s增加至0.1mm/s,岩样吸收的总应变能 具有波动性,可释放的弹性应变能 增幅60.42%,耗散应变能 降幅 66.38%, 增幅43.33%, 降幅66.67%,岩样破裂模式由拉剪破坏逐渐向张拉劈裂破坏过渡,岩样破裂块数增多。（4）加载速率为0.001~0.1 mm/s时,岩样破坏方式有所不同,但破坏为同一类损伤过程。单轴压缩状态下,能量耗散使得岩样损伤致使强度丧失,而能量释放使得岩样宏观破裂面贯通,并向着能量释放的方向张裂或弹射破坏。     

频繁动力扰动对围压卸载中高储能岩体的动力学影响

基于冬瓜山铜矿深部巷道围岩开挖过程中面临的高应力和频繁爆破扰动问题，利用改进的SHPB动静组合加载系统，开展了频繁动力扰动对围压卸载中高储能岩体动力学影响的研究。研究结果表明，围压卸载中的矽卡岩受到动力扰动时，其动态峰值应力和弹性模量随动力扰动次数非线性变化。围压卸载中的高储能矽卡岩受到动力扰动时会释放能量。轴压促使岩样内微裂隙轴向发育，造成岩样抵抗动力扰动能力减弱；围压减缓岩样内微裂隙轴向发育，造成岩样抵抗动力扰动能力增强。动力扰动对微裂隙扩展有促进作用，使围压卸载中的岩样由拉伸破坏向剪切破坏转变。     

单轴循环冲击下弱风化花岗岩的损伤演化

为研究爆破应力波作用下弱风化花岗岩的力学特性和损伤演化机理，利用直径50 mm的改进分离式Hopkinson压杆装置，开展以不同速度对花岗岩进行单次和等速循环冲击下的实验研究。研究结果表明:单次冲击中，用能量法确定的损伤阈值，可用于循环冲击实验中；不同应变率下弱风化岩石裂纹扩展阶段存在应力松弛平台，且随应变率升高而愈发明显，峰值应力与应变率呈正相关。等速循环冲击中，最大应力、应变与冲击速度呈正相关，与岩样累积冲击总次数呈负相关；损伤演化具有3个阶段呈倒S形，由其构建的双参数损伤演化模型拟合效果理想，且具有物理意义；利用模型中的参数α和β可计算中值点处的损伤度和相对循环次数，且与冲击速度正相关；不同损伤变量计算的损伤演化模型不同，合理定义损伤变量是必要的。     

化学腐蚀后砂岩三轴压缩力学特性及其能量机制的试验研究

为研究不同化学溶液对砂岩力学性质及能量特征的影响,采用不同的水化学溶液对砂岩试样进行腐蚀,利用WDT-1500多功能材料试验机对化学腐蚀后饱和状态与自然状态的试样进行常规三轴压缩试验。试验结果表明:化学腐蚀后砂岩试样的强度及其抗变形能力呈现不同程度的劣化;化学腐蚀后砂岩试样的峰值应变小于相同围压下自然状态试样的峰值应变,与单轴压缩条件下不同,这可能是由于围压和化学溶液共同作用的结果;砂岩试样的似软化系数与围压之间呈现负相关性,同时,其降低速率随着围压的增加而降低。砂岩试样峰值前吸收的能量绝大部分是以可释放弹性应变能Ue形式储存下来的,而化学腐蚀后砂岩试样以Ue形式储存下来的能量占其总吸收应变能的百分比却有所下降;同时,围压与试样的可释放应变能/应变能比值之间呈负相关性,而与耗散能/应变能比值存在正相关性;岩石脆性指标修正值呈现不同程度的增加,试样的脆性减弱延性增强,即塑性变形增加,塑性变形与耗散能之间具有很好的线性特征。溶液的pH值、浓度和化学成分对砂岩试样峰值处各部分应变能的影响显著。     

Experimental Investigation on Mechanical Behavior of Coarse Marble Under Six Different Loading Paths

A series of triaxial compression experiments were preformed for the coarse marble samples under different loading paths by the rock mechanics servo-controlled testing system. Based on the experimental results of complete stress-strain curves, the influence of loading path on the strength and deformation failure behavior of coarse marble is made a detailed analysis. Three loading paths (Paths I–III) are put forward to confirm the strength parameters (cohesion and internal friction angle) of coarse marble in accordance with linear Mohr-Coulomb criterion. Compared among the strength parameters, two loading paths (i.e. Path II by stepping up the confining pressure and Path III by reducing the confining pressure after peak strength) are suggested to confirm the triaxial strengths of rock under different confining pressures by only one sample, which is very applicable for a kind of rock that has obvious plastic and ductile deformation behavior (e.g. marble, chalk, mudstone, etc.). In order to investigate re-fracture mechanical behavior of rock material, three loading paths (Paths IV–VI) are also put forward for flawed coarse marble. The peak strength and deformation failure mode of flawed coarse marble are found depending on the loading paths (Paths IV–VI). Under lower confining pressures, the peak strength and Young’s modulus of damage sample (compressed until post-peak stress under higher confining pressure) are all lower compared with that of flawed sample; moreover mechanical parameter of damage sample is lower for the larger compressed post-peak plastic deformation of coarse marble. However under higher confining pressures (e.g. σ ₃?=?30 MPa), the axial supporting capacity and elastic modulus of damage coarse marble (compressed until post-peak stress under lower confining pressure) is not related to the loading path, while the deformation modulus and peak strain of damage sample depend on the difference of initial confining pressure and post-peak plastic deformation. The friction among crystal grains determines the strength behavior of flawed coarse marble under various loading paths. In the end, the effect of loading path on failure mode of intact and flawed coarse marble is also investigated. The present research provides increased understanding of the fundamental nature of rock failure under different loading paths.     

Erratum to: Experimental Investigation on Mechanical Behavior of Coarse Marble Under Six Different Loading Paths

A series of triaxial compression experiments were preformed for the coarse marble samples under different loading paths by the rock mechanics servo-controlled testing system. Based on the experimental results of complete stress-strain curves, the influence of loading path on the strength and deformation failure behavior of coarse marble is made a detailed analysis. Three loading paths (Paths I–III) are put forward to confirm the strength parameters (cohesion and internal friction angle) of coarse marble in accordance with linear Mohr-Coulomb criterion. Compared among the strength parameters, two loading paths (i.e. Path II by stepping up the confining pressure and Path III by reducing the confining pressure after peak strength) are suggested to confirm the triaxial strengths of rock under different confining pressures by only one sample, which is very applicable for a kind of rock that has obvious plastic and ductile deformation behavior (e.g. marble, chalk, mudstone, etc.). In order to investigate re-fracture mechanical behavior of rock material, three loading paths (Paths IV–VI) are also put forward for flawed coarse marble. The peak strength and deformation failure mode of flawed coarse marble are found depending on the loading paths (Paths IV–VI). Under lower confining pressures, the peak strength and Young’s modulus of damage sample (compressed until post-peak stress under higher confining pressure) are all lower compared with that of flawed sample; moreover mechanical parameter of damage sample is lower for the larger compressed post-peak plastic deformation of coarse marble. However under higher confining pressures (e.g. σ ₃ = 30 MPa), the axial supporting capacity and elastic modulus of damage coarse marble (compressed until post-peak stress under lower confining pressure) is not related to the loading path, while the deformation modulus and peak strain of damage sample depend on the difference of initial confining pressure and post-peak plastic deformation. The friction among crystal grains determines the strength behavior of flawed coarse marble under various loading paths. In the end, the effect of loading path on failure mode of intact and flawed coarse marble is also investigated. The present research provides increased understanding of the fundamental nature of rock failure under different loading paths.     

EXPERIMENTAL RESEARCH ON FAILURE AND ENERGY DISSIPATION CHRACTERISTICS OF THE SANDSTONE1)

通过三轴卸荷试验,探究了不同路径下卸荷速率对砂岩力学特性及破坏过程中的能量耗散的影响。试验结果表明在全过程应力-应变曲线的弹性阶段,轴向变形起主导作用,弹塑性阶段,环向应变的增加值大于轴向应变增加值。在围压卸荷阶段,卸荷速率越小,卸荷阶段的应变折合柔度越大,此时岩样的变形不充分,呈现明显的脆性破坏。恒主应力差路径下的耗散能大于恒轴压路径下的耗散能的35%,卸荷速率越大,岩样的弹性应变能越小。     

循环冲击层理煤岩动力学行为及破坏规律研究

为研究复杂地况下含特征层理煤岩的动态力学行为，采用■50 mm分离式霍普金森压杆实验系统，对含层理(0°、30°、45°、60°、90°)煤岩进行动态三轴循环冲击实验研究，并结合3D轮廓扫描仪量化其断裂界面，分析层理效应和围压效应对煤岩动态力学特性及其损伤破坏规律的影响。研究表明：围压的施加使煤岩应力-应变曲线出现弹性后效现象；较无围压状态，抗压强度提高3.9～4.2倍，失效应变增大2.59～3.05倍。随着层理角度的增大，煤岩的动态抗压强度、弹性模量和能量透射率均呈现先降低后升高的U形分布，在层理角为45°时均达到最小值；能量吸收率和断面粗糙度呈现先增大后减小的∩形分布，损伤变量呈现N形分布，在层理角为45°时达到最大值。煤岩的损伤破坏特征随层理角度的变化可概括为张拉破坏（0°）-剪切破坏（30°、45°和60°）-劈裂破坏（90°）的演变过程，所得特征规律可为实际复杂环境下煤层气资源安全高效开采提供理论支持。     

EXPERIMENTAL STUDY OF MECHANICAL PROPERTIES OF WATER-COOLED GRANITE UNDER HIGH TEMPERATURE1)

通过对高温加热-遇水快速冷却后的花岗岩试样进行单轴和三轴实验,研究了800°C内高温花岗岩遇水快速冷却后的力学性质随温度和围压的变化规律。实验结果表明：(1)400°C为高温加热-遇水快速冷却对花岗岩力学性质影响的阈值;(2)同一温度条件下,峰值偏应力、峰值应变随围压的增大而增大;弹性模量随围压的增大先增大后减小;(3)单轴实验中,温度低于400°C时,岩样表现为复合破坏,随着温度的升高破坏形式转变为拉破坏;三轴实验中,岩样整体上表现为剪切破坏。     

压缩载荷作用下岩石的细观损伤和塑性研究

建立岩石微裂纹扩展的细观力学模型,研究了岩石的细观损伤和塑性性质.压缩载荷下微裂纹尖端翼裂纹稳定扩展表征岩石的细观损伤,采用应变能密度准则求解复合型断裂的翼裂纹扩展长度,微裂隙统计的二参数Weibull函数模型反映绝对体积应变对微裂纹分布数目影响,进而用翼裂纹扩展所表征的应力释放体积和微裂纹数目来表示含有微裂隙的岩石损伤演化变量;宏观塑性屈服函数采用Voyiadjis等的等效塑性应变的硬化函数,反映了塑性内变量对硬化函数的影响;建立岩石模型的本构关系及其数值算法,并用回映隐式积分算法编制了模型的本构程序.分析弹塑性损伤模型的围压对岩石损伤的影响,并从围压和短微裂隙长度等因素分析模型的岩石的损伤和宏观塑性特性.     

单轴拉伸条件下脆性岩石微裂纹损伤模型研究

利用断裂力学、损伤力学和均匀化原理,对脆性岩石单轴拉伸条件下的力学特性进行分析,建立了脆性岩石的微裂纹损伤本构模型.首先对岩石内部微裂纹的统计分布规律进行分析,给出了理论分析过程中微裂纹分布的假设条件,在此基础上,参考已有研究成果,得到含细长微裂纹脆性岩石有效弹性参数的计算公式.然后,对岩石内部单一微裂纹进行断裂力学和损伤力学分析,得到了扩展裂纹尖端的应力强度因子计算公式,在一定微裂纹断裂扩展准则和断裂扩展速率的假设基础上,利用积分原理,得到了岩石整体的损伤变量和损伤演化方程,由此建立单轴拉伸条件下脆性岩石的微裂纹损伤本构模型.最后,通过一花岗岩的单轴拉伸试验结果对微裂纹损伤本构模型进行了验证.     

Loading rate and confining pressure effect on dilatancy,acoustic emission,and failure characteristics of fissured rock with two pre-existing flaws

Investigating the dilatancy, acoustic emission and failure characteristics of fissured rock are significant to ensure their geotechnical stability. In this paper, the uniaxial and triaxial compression experiments with AE monitoring under different loading rates were carried out on fissured rock specimens with the same geometrical distribution of two pre-existing flaws. The dilatancy and AE activity of these specimens were discussed, and the effects of the confining pressure and loading rate on the mechanical parameters and failure characteristics were analyzed. The results show that the exponential strength criterion is more suitable than the Mohr–Coulomb strength criterion to characterize the strength characteristics of fissured rock. The crack evolution and failure characteristics of fissured rock specimens are more complicated than those of intact rock specimens. The failure characteristics of the fissured rock follow the tensile shear coalescence model, crack branching occurs with increasing the loading rate, and the multi-section coalescence model is verified with increasing the confining pressure. The phenomena of stress drop and yield platform usually occur after the dilatancy onset, the specimen does not fail instantaneously, and the propagation and coalescence of cracks cause a sharp increase in the AE signals, circumferential strain, and volumetric strain.