随机超载对疲劳裂纹扩展迟滞效应的模拟

考虑超载的迟滞效应,对随机超载作用下的疲劳裂纹扩展进行了模拟计算．载荷谱为在基本恒幅循环载荷基础上加入一以泊松流发生的随机超载序列,超载的大小为均匀分布．采用裂纹闭合模型考虑超载的迟滞效应,认为裂纹张开应力在超载引起的塑性区内按线性规律衰减．循环续循环模拟计算出裂纹从初始长度一直到疲劳破坏的扩展曲线．据此,计算了各种超载发生强度和大小下的疲劳裂纹扩展寿命的平均值与标准差。     

正交异性钢桥面板肋-面板焊缝疲劳分析

基于焊缝的局部三维断裂力学模型和超重多轴货车的载荷谱,进行正交异性钢桥面板的肋-面板焊缝表面裂纹的疲劳寿命分析。采用Schwartz-Neuman交替法计算肋-面板焊缝处半椭圆表面裂纹的应力强度因子,基于裂尖反向塑性区模型考虑循环载荷中压应力对疲劳裂纹扩展的作用。正交异性钢桥面板的肋-面板焊缝的应力计算结果表明:超载货车作用下肋-面板焊缝处的横向应力峰值和应力幅都有明显增加;相比于标准疲劳荷载车,超载货车作用下肋-面板焊缝处半椭圆表面裂纹的裂纹扩展率增大了6.1倍;对应于正交异性钢桥面板的肋-面板焊缝处的拉-压循环应力,平面应变状态下的裂尖反向塑性区使裂纹扩展率增加了3.7倍;基于所得裂纹扩展速率,本研究给出仅在严重超载的五轴和六轴货车作用下正交异性钢桥面板的肋-面板焊缝疲劳寿命不足20年,远远低于桥梁的设计寿命。因此,考虑超载多轴货车的载荷谱和循环载荷中的压应力对肋-面板焊缝疲劳裂纹扩展的影响十分重要。     

负超载对Al-2024疲劳裂纹扩展的影响

本文讨论了负超载对Al-2024铝合金材料疲劳裂纹扩展的影响,试验发现在大量负超载循环周次之后也有裂纹停滞现象发生。这种停滞现象的产生与剪切唇的形成有关。本文发现负超载期间的剪切唇(简称剪切唇Ⅰ)和负超载之后的剪切唇(简称剪切唇Ⅱ)对疲劳裂纹扩展速率影响的程度不同。从裂纹闭合的观点建立了负超载对疲劳裂纹扩展影响的计算模型。     

铸镁合金机轮损伤容限设计

本文系统地研究了铸造镁合金的断裂,疲劳和疲劳裂纹扩展性能.着重探讨了在常幅,超载及实际飞行载荷谱下的裂纹扩展规律,提出了可用的基本设计数据和寿命估算方法,并进行了结构实物试验验证工作.     

CTS试件中复合型疲劳裂纹扩展

针对复合型循环载荷作用下的金属构件中的裂纹扩展问题进行了实验分析和理论建模. 首先 采用紧凑拉剪试件(CTS)和 Richard研制的复合型载荷加载装置，对承受复合型循环载荷的裂纹进行了实验研究. 实验选择了两种金属材料试件，分别承受3种形式的复合型循环载荷的作用，在裂纹尖端具 有相同的初始应力场强度的条件下考察复合型循环载荷对裂纹扩展规律的影响. 实验结果表明，疲劳裂纹的扩展速率与加载角度有关. 对于同样金属材料的试件，当裂尖处 初始应力场强度相等时，载荷越接近于II型，裂纹增长速率越快. 采用等效应力强度 因子(I型和II型应力强度因子的组合)、裂纹扩展速率及复合强度等参数，以实验数据为 基础，建立了一个疲劳裂纹扩展模型，用来预测裂纹在不同模式疲劳载荷作用下的扩展速率. 为验证其有效性，该模型被应用于钢制试件的数值模拟计算中. 实验结果与模拟计算曲线保 持一致，表明该模型可以用来估算带裂纹金属构件的寿命.     

Ⅱ型裂纹疲劳扩展中超载行为的研究

利用铝合金ＬＹ１２ＣＺ制十字型试样进行Ⅱ型裂纹的疲劳扩展试验，施加若干次短瞬的Ⅱ型超载。发现Ⅱ型裂纹的超载行为与Ⅰ型裂纹的不同，裂纹的扩展速率可几倍于未超载时相同应力强度因子幅度下的扩展速率；而且超载后的短瞬期间，裂纹在塑性区内仍保持较快的速率扩展。试验研究表明：Ⅱ型超载和Ⅰ型超载也许分别受不同的机制控制；它更类似于Ⅲ型超载。     

描述复合型疲劳裂纹扩展路径的等效模型

复合型裂纹的扩展路径不同于Ⅰ型裂纹，会沿着与初始裂纹面不同的方向扩展，扩展路径的准确预测对扩展速率的评估具有重要的作用。采用最大周向应力准则和最小应变能密度准则进行扩展路径的预测时，开裂角的误差会使裂纹不断偏离实际路径，造成最终结果的较大偏差。本文将复合裂纹在扩展过程中的弯折裂纹简化为直线裂纹，对简化过程中所产生的误差进行定量分析，并在此基础上提出了一种描述复合型裂纹扩展路径的等效修正模型。将此模型写入ABAQUS扩展有限元模块，实现了基于等效修正模型的疲劳裂纹扩展程序。通过对含中心斜裂纹板的疲劳裂纹扩展试验，验证了本模型的有效性，预测的开裂角与试验结果基本一致，所得到的载荷循环次数低于试验值，对含裂纹结构的寿命评估偏于保守。     

考虑材料循环塑性的疲劳裂纹扩展模拟

提出了一种考虑材料循环塑性性能的研究疲劳裂纹扩展与闭合行为的有限元模拟方法．对所选用的循环塑性本构关系进行了基本实验检验．探讨了在疲劳裂纹扩展有限元分析中网格尺寸的影响，给出了网格优化准则．研究了在循环硬化条件下考虑裂纹合效应时裂纹面张开廓形、裂纹尖端应力、应变场和正反向塑性区的演变规律．对于循环硬化和不同循环应力比Ｒ等因素对裂纹张开应力水平的影响也作了考察     

铝合金切口件在四组变幅载荷下3.5%NaCl溶液中腐蚀疲劳裂纹起始寿命试验研究与估算模型

试验研究了铝合金切口件在4组变幅块谱下、3．5％NaCl溶液中腐蚀疲劳裂纹起始寿命．结果表明，变幅载荷谱中的大超载会显著延长腐蚀疲劳裂纹起始寿命，并且加载顺序具有明显的影响．根据反映大小载荷交互作用的超载腐蚀疲劳裂纹起始寿命曲线和Miner累积损伤定则，建立了变幅载荷下切口件腐蚀疲劳裂纹起始寿命估算模型，应用该模型估算的结果与试验结果相吻合．     

考虑T-stress的非正态随机参数疲劳裂纹扩展寿命的可靠性分析

基于断裂力学的疲劳裂纹扩展寿命问题的研究常常将裂纹尖端应力展开项的高次项忽略,引起了裂纹扩展模拟的误差,本文考虑高次项T-stress对裂纹扩展角的影响,对裂纹扩展过程做了数值模拟,结果显示相同裂纹扩展长度下,考虑T-stress会延长裂纹扩展寿命。文章首先采用修正的Paris-Erdogan 公式计算了两端承受均布拉伸载荷的边缘斜裂纹板的疲劳裂纹扩展寿命,裂纹扩展方向采用两参数修正的最大拉应力准则。由于结构尺寸,材料特性和载荷等因素具有不确定性,导致疲劳裂纹扩展过程带有一定的随机性,本文以材料属性和载荷为随机变量,在随机有限元法的基础上,结合计算可靠度的四阶矩法,Edgeworth级数展开方法,提出随机参数服从任意分布时的结构疲劳裂纹扩展寿命可靠度的计算方法。分析了参数为非正态分布时的平板裂纹扩展寿命可靠度随裂纹扩展的变化过程。本文方法可预测工程中板裂纹的扩展行为,以及预测裂纹板的可靠度。     

过载作用下聚乙烯疲劳裂纹扩展行为研究

论文针对中密度聚乙烯材料(MDPE)，采用平板试样进行了I型疲劳裂纹扩展和单次过载下裂纹扩展试验．发现与金属材料类似，单次拉伸过载对聚乙烯(PE)的疲劳裂纹扩展有明显的迟滞作用，降低了裂纹扩展速率．试验还通过变载荷刻线法获取疲劳裂纹扩展前缘的实际形貌和变化规律，对常规变载荷刻线方法进行了调整和验证，其修正方法对高分子材料的疲劳裂纹扩展前缘刻线具有较好的效果．通过观察发现含楔形塑性区的裂尖钝化是裂纹迟滞的主要原因．过载引入的塑性区内残余应力对裂纹迟滞也起了重要作用．论文利用Dugdale模型计算了塑性区尺寸，使用基于残余应力的Wheeler模型对过载迟滞进行了很好的拟合．     

A cohesive zone model for fatigue crack growth allowing for crack retardation

A damage-based cohesive model is developed for simulating crack growth due to fatigue loading. The cohesive model follows a linear damage-dependent traction–separation relation coupled with a damage evolution equation. The rate of damage evolution is characterized by three material parameters corresponding to common features of fatigue behavior captured by the model, namely, damage accumulation, crack retardation and stress threshold. Good agreement is obtained between finite element solutions using the model and fatigue test results for an aluminum alloy under different load ratios and for the overload effect on ductile 316 L steel.     

The effects of overloads on sustained-load crack growth in a nickel-base superalloy: part I—analysis

Analytical procedures are presented for predicting the retardation effects of cyclic overloads on the sustained load crack growth rate in Inconel 718 at 649°C. The Wheeler model is used in a crack growth computer program, CRACKS, by representing sustained load by equivalent fatigue cycles per unit time and an equivalent stress ratio, R. A new model, the exponential overload (EXPOL) model, is developed based on the concept of a crack growing at a retarded rate through an overload plastic zone. The analytical procedures use a minimum of empirical constants and are capable of accurately representing the time-dependent sustained load crack growth behavior with single or Multiple cyclic overloads.     

基于非齐次复合Poisson过程的正交异性钢桥面板细节疲劳裂纹随机扩展研究

传统的正交异性钢桥面板疲劳损伤评估常采用确定性和可靠性分析方法,忽略了疲劳裂纹扩展的随机性影响,针对这一问题,提出钢桥面板细节疲劳随机扩展分析方法。本文以南溪长江大桥为工程背景,基于长期车辆荷载监测数据,建立了车辆荷载非齐次复合Poisson过程模型。建立钢桥面板有限元模型,采用瞬态分析方法将随机车辆荷载转化成细节疲劳应力,基于线弹性断裂力学理论推导U肋-顶板焊接细节疲劳裂纹扩展时变微分方程,实现宏观关系式疲劳应力幅次数-疲劳损伤至微观表达式应力时间序列-疲劳损伤转换,讨论了车载次序及超载对疲劳裂纹扩展的影响。研究结果表明,非齐次复合泊松过程模型能够较好描述随机车流运营状态,车辆荷载的次序对疲劳裂纹扩展速率的影响不可忽略,重车排序靠前时能够促使疲劳裂纹扩展增速,南溪长江大桥细节点的车辆超载迟滞效应修正系数取值0.804。     

Fatigue crack growth behavior of Al7050-T7451 attachment lugs under flight spectrum variation

This paper discusses an analytical and experimental investigations of the fatigue crack growth behavior in attachment lugs subjected to a randomized flight-by-flight spectrum. In the analysis, the stress intensity factors for through-the-thickness cracks initiating from lug holes were compared by weight function method, boundary element method (BEM), the interpolation of Brussat’s solution. The stress intensity factors of a corner crack at a transition region were obtained using two parameter weight function method and correction factors. Fatigue life under a load spectrum was predicted using stress intensity factors and Willenborg retardation model considering the effects of a tensile overload. Experiments were performed under a load spectrum and compared with the fatigue life prediction using the stress intensity factors by different methods. Changes of fatigue life and aspect ratio according to the clipping level of the spectrum were discussed through experiment and prediction. Effect of the spectrum clipping level on the fatigue life was experimentally evaluated by using beach marks of fractured surface.     

基于裂纹闭合效应的高载迟滞预测模型修正

裂纹闭合效应通常是导致I 型裂纹扩展在高载作用下发生迟滞效应的主要因素之一．本文采用汽车薄板QSTE340TM 材料，针对不同应力比，高载比条件下疲劳裂纹扩展行为进行了实验研究．论文通过断面分析，针对各参数对裂纹闭合效应的具体影响进行了分析讨论，认为裂纹作用区域随裂纹扩展而动态变化，从而提出了一种对有效应力强度因子幅的修正方法．通过在原有模型中引入幂函数形式的动态变量α，表征裂纹闭合效应的作用比例随裂纹长度的动态变化，取得了较好的效果．     

A reexamination of plasticity-induced crack closure in fatigue crack propagation

The crack closure concept is often used to consider the R-ratio and overload effects on fatigue crack growth. The presumption is that when the crack is closed, the external load produces negligible fatigue damage in the cracked component. The current investigation provides a reassessment of the frequently used concept with an emphasis on the plasticity-induced crack closure. A center cracked specimen made of 1070 steel was investigated. The specimen was subjected to plane-stress mode I loading. An elastic–plastic stress analysis was conducted for the cracked specimens using the finite element method. By applying the commonly used one-node-per-cycle debonding scheme for the crack closure simulations, it was shown that the predicted crack opening load did not stabilize when the extended crack was less than four times of the plastic zone size. The predicted opening load was strongly influenced by the plasticity model used. When the elastic–perfectly plastic (EPP) stress–strain relationship was used together with the kinematic hardening plasticity theory, the predicted crack opening load was found to be critically dependent on the element size of the finite element mesh model. For R = 0, the predicted crack opening load was greatly reduced when the finite element size became very fine. The kinematic hardening rule with the bilinear (BL) stress–strain relationship predicted crack closure with less dependence on the element size. When a recently developed cyclic plasticity model was used, the element size effect on the predicted crack opening level was insignificant. While crack closure may occur, it was demonstrated that cyclic plasticity persisted in the material near the crack tip. The cyclic plasticity was reduced but not negligible when the crack was closed. The traditional approaches may have overestimated the effect of crack closure in fatigue crack growth predictions.     

A model for predicting the retardation effect following a single overload

Many engineering components are subjected to variable amplitude loading history. It is well known that retardation in fatigue crack growth occurs due to application of single overloads in a constant amplitude loading block. Many models have been proposed to capture this counter intuitive phenomenon which has resulted in improved understanding of retardation effect following tensile overloads and consequently resulting in better life prediction models. The proposed study is focused on to evaluation of retardation in fatigue life due to application of a single overload. A model for prediction of crack growth and crack growth rate following single overloads is presented. Several modifications to Wheeler’s growth idea are proposed, which incorporate a consideration for effective stress intensity factor, based on Elber’s concept of crack closure, relationship between overload ratio and the Wheeler’s exponent, and fatigue growth rate calculations. The results presented here show that plastic zone interaction following overload and the consideration of crack closure explain retardation effect following a single overload. Correlation between analysis and experimental data obtained from several sources in literature show that the scheme, is robust and provides an insight into the nonlinear aspect of crack growth results. The model has been tested for 2024-T3 aluminum alloy and 6061-T6 aluminum alloy and thorough calibrations performed, established the fidelity of the program.     

Numerical analysis of fatigue striations

A computational model was developed to numerically analyse fatigue striations. The inclined strip yield model with continuous distributions of infinitesimal dislocations was utilized to express the crack tip plasticity in this model. The fatigue crack tip blunting process was approximated by sequential activation of two slip lines under loading, and crack closure during unloading was taken into account. The plastic zone at a growing fatigue crack tip at the maximum load was independent of the crack growth up to ten cycles while the reversed plastic zone decreased in a size to one twentieth of that at the maximum load as the crack grew. The ratio of these plastic zone sizes and also the crack tip opening displacement were quite different from the simple prediction by J.R. Rice for a stationary crack. The computed striation spacings were compared with the observed ones and moderate agreement between them obtained.