采用压电机敏元件进行结构振动控制I：耦合系统动力分析

本文从机电耦合弹性体的理论出发，运用Ｈａｍｉｌｔｏｎ原理建立了一般压电耦合系统的动力分析模型，并给出了模态分析和有限元分析的耦合系统方程、作动方程及检测方程。该分析模型和计算公式可用于任意形状压电耦合系统的动力分析和振动控制设计。另外，导出的模态分析和有限元公式可用现有的商业软件求解。     

采用压电机敏元件进行结构振动控制：Ⅰ：耦合系统动力分析

本文从机电耦合弹性体的理论出发，运用Ｈａｍｉｌｏｎ原理建立了一般压电耦合系统的动力分析模型，并给出了模态分析和有限元分析的耦合系统方程，作动方程及检测方程，该分析模型和计算公式可用于任意形状压电耦合系统的动力分析和振动控制设计。另外，导出的模态分析和有限元公式可用现有的商业软件求解。     

电磁约束阻尼层结构振动主动控制研究

基于弹性、粘弹性、电磁学理论,应用Hamilton原理,导出了覆盖电磁约束层阻尼(EMCLD)主动控制方式的梁的控制方程,并针对覆盖EMCLD的悬臂梁,进行了主动控制仿真模拟,得到了较好的控制效果,分析了控制电流和阻尼层厚度对控制效果的影响.结果表明电磁约束阻尼技术具有结构简单、作动方式合理、耗能低的优点,是一种有效的振动主动控制方式.     

可控约束阻尼层板的杂交控制

用局部压电层控制约束阻尼约束层产生一种新的主、被动杂交控制形式,称为可控制 约束层。本文根据弹性材料、粘弹性材料、压电材料的本构关系和变形连续条件,建立了可控约束阻尼层板的控制微方程;从理论上证明了用离散小压电片组合来代替整体压电层而不影响作动效果,改善了结构的工艺性;利用Ｇａｌｅｒｋｉｎ方法和ＧＨＭ方法建立了系统的近似低阶方程对一试验模型进行了控制数值模拟和试验实现,结果表明这种杂交控制对控制     

风力机叶片压电振动的主动控制研究

提出了将智能材料粘贴在叶片表面或嵌入叶片内部形成新结构的概念。本文将智能材料作为传感器和作动器，通过机电耦合抑制叶片的振动；利用有限元软件 Algor 分析在气动力作用下叶片的应力、应变；基于压电陶瓷第一压电方程，将风电叶片简化成柔性悬臂梁，建立了压电智能悬臂梁状态空间的动力学模型；针对此系统利用最优控制理论进行主动振动控制，设计了在系统低阶模态空间的振动控制器。最后通过计算机仿真得出：系统振动幅度缩小了约20%，振动时间减少了约80%，从而说明了此主动振动控制方法的有效性和可行性，对防止叶片这一弹性体发生颤振也起到一定的作用。     

大型索网天线机电耦合动力学建模与主动变形控制

索网天线因其折叠收纳比高、质量轻以及口径大等优点,成为众多空间任务的首选天线形式,但反射面精度较低限制了大型索网天线的在轨性能指标。在索网天线竖向张力索中加入压电陶瓷堆(PZT)作动器,通过主动控制提高反射面的形面精度。首先,将张紧的索网天线分为含有作动器的主动索单元和不含作动器的被动索单元,通过压电本构方程、几何方程和哈密顿原理推导出主动索单元的动力学模型,并与被动索单元一起组装得到索网天线的机电耦合动力学模型。然后,根据天线反射面的初始形面误差和所建立的天线机电耦合动力学模型,基于模型预测控制(MPC)方法计算出各作动器的控制输入电压曲线。最后,以一个10m口径的索网天线为算例,验证本文所建立的模型和控制方法的有效性。     

支架振动的主动控制研究

利用压电材料的机电耦合特性，采用数值分析和实验相结合的方法研究了压电材料对支架的振动控制。利用Ｈａｍｉｌｔｏｎ原理，采用速度反馈，并考虑压电材料的机电耦合效应推导了振动主动控制有限元方程，分析了不同约束，不同压电片布置情况下支架的振动控制，实现了压电片的优化布置，同时用实验验证了数值分析的正确性。     

层叠式PVDF压电作动器及圆柱壳的振动主动控制

设计了一个层叠式PVDF压电作动器用于壳结构的振动控制。考虑压电层、粘接层、壳体耦合关系,推导了表面局部粘贴层叠式PVDF压电作动器的圆柱壳的振动控制方程,给出了作动力与压电层和粘接层层数、厚度之间的关系以及作动力与作动器粘贴位置之间的关系。针对一端固定、另一端自由的圆柱壳,进行了振动控制仿真。结果表明层叠式PVDF压电作动器作动力与作动器层数近似成线性关系,增大作动器层数能有效增大作动力,在低控制电压下能显著抑制圆柱壳振动,作动器周向不完全粘贴时,在径向产生的径向作动力对壳体横向振动控制非常有利。说明了层叠式PVDF压电作动器是一种可用于壳体结构振动并具有良好作动效果的作动器。     

自感知主被动阻尼悬臂梁动态特性分析

由Ｈａｍｉｌｔｏｎ原理导出了压电层作约束层作约束层的自感知主被动阻尼控制结构的振动控制方程;由自感知电压引入速度负反馈闭环控制,并由假设模态法将位移按模态展开,求解了悬臂梁结构的动态特征;对被动控制、自感知主动控制、自感知主被动控制的控制效果进行了分析比较;分析了粘弹层厚度变化、材料参数变化以及压电层厚度、位置等结构参数变化对控制效果及模态频率的影响;并对自感知主被动阻尼控制结构的特点和设计中应注     

支架的振动控制

利用 Hamilton原理 ,考虑压电材料的机电耦合效应 ,建立含压电材料结构的有限元控制方程。采用数值分析方法研究了支架振动的主动控制、主被动联合控制和振动隔离 ,对改善支架动态特性有实用价值     

Dynamic characteristics of a cantilever beam with partial self-sensing active constrained layer damping treatment

The equations of motion governing the vibration of a cantilever beam with partially treated self-sensing active constrained layer damping treatment(SACLD) are derived by application of the extended Hamilton principle. The assumed-modes method and closed loop velocity feedback control law are used to analyze and control the flexural vibration of the beam. The influence of the bonding layer and piezoelectric layer thickness, material properties, placements of the piezoelectric patch and feedback control parameters on the actuation ability of the vibration suppression are investigated. Some design considerations for pure passive, pure active control, and self-sensing active constrained layer damping are discussed. The present work is supported by the National Natural Science Foundation of China (No. 59635140).     

压电智能梁振动控制的优化设计

本文研究了压电智能梁振动控制中压电传感作动元件的优化设计,并考虑了控制增益和结构阻尼的影响。采用负速度反馈控制策略及等效阻尼比优化准则。对简支梁和悬臂梁采用遍历搜索的方法计算了不同增益和结构阻尼下的优化,结果对进一步研究优化设计和振动控制有一定的参考价值。     

Effect of debonding in active constrained layer damping patches on hybrid control of smart beams

A new model for a smart beam with a partially debonded active constrained layer damping (ACLD) patch is presented, and the effects of the debonding of the ACLD patch on both passive and hybrid control are investigated. In this model, both shear and compressional vibrations of the viscoelastic material (VEM) layer are considered. The moment inertia and the transverse shear effect are also taken into account based on the Timoshenko’s beam theory. The adhesive layer between the host beam and the piezoelectric sensor patch is modeled as an elastic load transferring media. The debonding of the ACLD patch is approximated by removing the VEM between the constraining layer and the host beam in the debonding region, and the continuity conditions are imposed based on displacement continuity and force balance. A modal velocity observer-based modal control scheme is also given to perform the active modal control of the beam. In order to examine the effects of part debonding of the ACLD patch, the characteristic equation of the beam treated with an ACLD patch is derived. The simulation example results show that an edge debonding of the ACLD patch can significantly affect both passive and hybrid control. It is also found that the additional mode induced by the debonding has unique effects on the modal damping ratios and frequencies of both open-loop and closed-loop system.     

Nonlinear-forced vibrations of piezoelectrically actuated viscoelastic cantilevers

This paper aims to study the nonlinear-forced vibrations of a viscoelastic cantilever with a piecewise piezoelectric actuator layer on its top surface using the method of Multiple Scales. The governing equation of motion is a second-order nonlinear ordinary differential equation with quadratic and cubic nonlinearities which appear in stiffness, inertia, and damping terms. The nonlinear terms are due to the piezoelectricity, viscoelasticity, and geometry of the system. Forced vibrations of the system are investigated in the cases of primary resonance and non-resonance hard excitation including subharmonic and superharmonic resonances. Analytical expressions for frequency responses are derived, and the effects of different parameters including damping coefficient, thickness to width ratio of the beam, length and position of the piezoelectric layer, density of the beam, and the piezoelectric coefficient on the frequency-response curves are discussed for each case. It is shown that in all these cases, the response of the system follows a softening behavior due to the existence of the piezoelectric layer. The piezoelectric layer provides an effective tool for active control of vibration. In addition, the effect of the viscoelasticity of the beam on passive control of amplitude of vibration is illustrated.     

机敏柔性梁的振动主动控制

提出了用于机敏结构中振动主动控制的仿人控制算法,对压电阻尼技术进行了理论和实验研究,给出了传感器,执行器和受控结构之间的关系,用ＰＺＴ作执行元件实现了柔性梁振动主动控制系统,给出了实验结果。     

基于反激变压器的压电振动能量双向操控技术

压电材料因其具有良好的机电耦合特性, 在振动能量俘获和结构振动控制领域有着良好的应用前景. 基于同步开关和电感的压电元件接口控制电路, 可以通过振荡电路工作原理调节压电元件的电压幅值和相位, 优化压电振动系统的机电能量转化. 优化型同步电荷提取技术即基于上述接口控制电路实现了压电振动能到电能的高效转换. 本文提出了一种衍生于优化型同步电荷提取电路的压电阻尼半主动控制电路, 借鉴反激变压器的原、副边能量转换特性, 实现了压电振动控制系统从电能到机械能的能量操控, 进而达到结构振动抑制的效果. 至此, 结合了压电电荷能提取与压电阻尼半主动控制技术的新电路, 以反激变压器为核心实现了压电振动能量的双向操纵. 论文首先介绍了相应的控制电路及工作原理, 推导了新型同步开关阻尼技术下的结构的振动阻尼比模型, 搭建了压电悬臂梁振动控制实验平台, 最终通过实验验证了理论模型, 并使用更简单的控制方法解决了振动控制系统的稳定性问题.      

Parametric vibration stability and active control of nonlinear beams

The vibration stability and the active control of the parametrically excited nonlinear beam structures are studied by using the piezoelectric material. The velocity feedback control algorithm is used to obtain the active damping. The cubic nonlinear equation of motion with damping is established by employing Hamilton’s principle. The multiple-scale method is used to solve the equation of motion, and the stable region is obtained. The effects of the control gain and the amplitude of the external force on the stable region and the amplitude-frequency curve are analyzed numerically. From the numerical results, it is seen that, with the increase in the feedback control gain, the axial force, to which the structure can be subjected, is increased, and in a certain scope, the structural active damping ratio is also increased. With the increase in the control gain, the response amplitude decreases gradually, but the required control voltage exists a peak value.     

Active vibration control of thin constrained composite damping plates with double piezoelectric layers

Vibrations and the damping behaviour of thin constrained composite plates with double piezoelectric layers are analytically explored by using Fourier transformation and classical laminated plate theory. Electric potential equations in the double piezoelectric layers are solved with respect to closed and open circuit boundary conditions, an exterior dielectric slab and active control. The natural frequencies and loss factors of the constrained smart composite plates with passive control methods are not notably changed in comparison with those of the constrained composite plates without piezoelectric effects since vibrational energy does not efficiently convert to electrical energy. The loss factors of the composite plates with active constrained damping increase and the natural frequencies have significant variations as the proportional derivative gains increase. Transverse displacement power spectra of the piezoelectric composite plates with active control are compared with those of the piezoelectric composite plates with passive control showing that active control has the best suppression performance of vibrations for the constrained laminated plates with double piezoelectric layers. Radial power spectral density, phase angles and cylindrical-wave power spectral density are calculated. Interesting patterns of wave propagation are explained when plane wave expansion is used to obtain Bessel cylindrical waves.     

压电智能环形板的主动控制

对在不同位置粘有任意多组压电传感器和压电执行器的轴对称弹性环形薄板的振动控制进行了研究．根据压电执行元件的等效作用量得到了压电智能环板的振动控制方程和传感方程,再利用分离变量法以及由传感器测得的电量和作用在执行器上电压之间的控制模式得到振动方程的全解．实行了对整体结构的主动控制．对不同的压电片布置进行了数值计算．结果表明：当离散分布压电元件布置越密,振动衰减的效果越佳