K0超固结土的不排水抗剪强度

结合K0超固结上模型、旋转角w公式、临界状态不排水条件以及基于SMP的变换应力张量建立了不排水抗剪强度的统一表达式;采用三轴压缩、三轴拉伸的应力洛德角θ、旋转角w建立了三轴压缩、三轴拉伸条件下的不排水抗剪强度公式;基于临界状态士力学,推导出了平面应变条件下的应力洛德角θ、旋转角w的表达式,进而得到平面应变条件下的不排水抗剪强度公式.分别采用三轴压缩、三轴拉伸和平面应变条件下试验数据对所提出的不排水抗剪强度公式进行验证,预测结果和试验数据的基本吻合表明了不排水抗剪强度公式的合理性.     

超固结饱和黏性土的弹塑性本构模型及三轴试验模拟

针对饱和超固结黏性土现有的下加载面修正剑桥模型破坏应力比为定值,不能反映土体在不同应力状态下强度特性存在差异这一问题,为了更好地反映应力状态变化对破坏应力比的影响,基于三剪统一强度准则确定超固结土的破坏应力比。在此基础上得到了超固结土的弹塑性本构模型,该模型的特点是能够描述土体受力时的中间主应力效应、应力区间效应、拉压差影响。基于该本构模型作了常规三轴压缩条件下超固结饱和黏性土的模拟结果与试验结果对比,结果表明:该模型能够反映不同超固结比下土的变形、剪胀、孔隙水压力变化特性和规律。利用该本构模型模拟了排水和不排水条件下的真三轴压缩试验,得到了相应的应力-应变特性曲线。     

卸荷条件下粉质粘土变形性状研究

通过室内应力控制的三轴试验研究卸荷条件下土体的应力-应变关系和孔隙水压力变化特征,得到变形模量的确定方法。研究表明:在初始偏压应力固结条件下,无论是轴向压力保持不变而侧向压力不断卸荷,还是轴向压力和侧向压力同时卸荷,其应力-应变关系均表现为较好的双曲线函数关系。而且,侧向固结压力愈大,强度值愈大。在卸荷过程中,随剪切应力的增大和剪切应变的发展,土样呈现剪胀趋势并在后期产生较大的负孔隙水压力。不排水条件下由于负孔隙水压力的存在,土样的表观强度略有增大。     

Undrained shear strength for K0{K}_{0}K0 overconsolidated clays K01)}K0

结合K0超固结土模型、旋转角K0\omegaK0公式、临界状态不排 水条件以及基于SMP的变换应力张量建立了不排水抗剪强度的统一表达 式;采用三轴压缩、三轴拉伸的应力洛德角K0\thetaK0、旋转角K0\omega K0建立了三轴压缩、三轴拉伸条件下的不排水抗剪强度公式;基于临界状态土力学,推导出了 平面应变条件下的应力洛德角K0\thetaK0、旋转角K0\omega K0的表达式,进而得到平面应变条件下的不排水抗剪强度公式. 分别采用三轴压缩、三轴拉伸 和平面应变条件下试验数据对所提出的不排水抗剪强度公式进行验证,预测结果和试验数据 的基本吻合表明了不排水抗剪强度公式的合理性.     

正常固结原状饱和黏性土的本构模型研究

基于扰动状态概念研究了正常固结饱和原状黏性土的本构模型。其中,相对完整状态采用基于原状黏性土的理想非线性弹性本构模型来表征;完全调整状态则是基于临界状态土力学框架,将修正剑桥模型与三剪强度准则相结合而建立的弹塑性本构模型来表征。为了更好地反映黏性土的黏聚力影响,提出了等量代换法和坐标平移法两种处理方法,并作了对比研究。针对基于临界状态土力学框架和扰动状态概念建立的原状土本构模型为平均应力、广义剪应力与体应变、广义剪应变间的关系且无屈服函数显式表达式,提出了一个将其三维化的方法。三维化后的原状黏性土本构模型为空间内6个应力分量和6个应变分量之间的关系,更便于复杂应力状态下的土体变形分析及有限元编程。为验证模型的正确性,对正常固结江西原状饱和红黏土土样作了固结排水和固结不排水条件下的常规三轴压缩试验和K0固结试验,并与模型计算结果作了对比,结果表明:所提模型能够较好地反映江西原状饱和红黏土的力学和变形特性。另外,用所提模型对江西原状饱和红黏土进行了真三轴压缩数值模拟实验,探讨了中间主应力对其力学和变形特性的影响,结果表明:中间主应力及其影响系数对土的变形、孔隙水压力、强度均有影响;固结不排水条件下,在相同剪应力的作用下,土体剪应变随中间主应力影响系数的增大而减小,在相同轴向应变条件下,孔隙水压力随中间主应力影响系数的增大而增大;固结排水条件下,在相同平均正应力作用下,土体体应变随中间主应力影响系数的增大而减小,在相同轴向应变条件下,土体体应变随中主应力影响系数的增大而增大。     

饱和超固结黏性土的三剪弹塑性本构模型研究

针对饱和超固结黏性土现有下加载面修正剑桥模型中破坏应力比为定值、土体黏聚力为零,以及不能准确反映不同应力状态下土的强度差异这些问题,基于三剪统一强度准则以及应力坐标平移法得到了扩展破坏应力比,其特点是能更好地反映应力状态变化以及土体黏聚力的影响。在此基础上提出了饱和超固结黏性土的三剪弹塑性本构模型,该模型的特点是能描述土体受力时的中间主应力效应,应力区间效应和拉压差影响,同时也能更好地考虑土体黏聚力的影响。基于该模型对ABAQUS软件进行了二次开发,并利用其模拟了饱和超固结黏性土在排水和不排水条件下的真三轴和常规三轴压缩试验特性。对常规三轴压缩条件下土体力学特性作了模拟和试验结果对比。结果表明所提模型能很好地反映不同超固结比下土体的变形、剪胀、孔隙水压力变化特性。     

压实粉土非线性应力-应变关系的试验研究

对京九线路基粉土用GDS三轴仪进行固结不排水剪试验,研究不同围压、含水量、压实度下压实粉土样的应力-应变关系。结果表明:压实粉土在低围压下为应变软化,高围压下为应变硬化,存在一个屈服应力;含水量和压实度对粉土强度和应力-应变关系影响显著,随着含水量的减小、压实度的增大,压实粉土样强度增大,应力-应变曲线上升。对围压小于屈服应力的应变软化曲线,用常规的土的软化关系式进行拟和;对围压大于屈服应力的应变硬化曲线,用邓肯-张模型进行拟和;这二者的结合能描述压实粉土的应力-应变关系曲线,效果良好。     

K0超固结结构性黏土的本构模型

K₀固结黏土在自然界广泛分布, 其通常同时具有超固结性与天然结构性, 而K₀超固结性又与K₀正常固结性质存在很大差异. 为了有效的描述K₀超固结性质, 在结构性模型基础上, 做了如下三点改进, 使得原模型拓展为同时考虑K₀超固结特性与天然结构性影响的本构模型. (1)引入相对应力比来描述屈服面, 并引入初始各向异性转轴参量ξ来表达初始各向异性对屈服面在p-q空间的位置影响. (2)基于给定的屈服面方程, 推导得到变相应力比参量, 并将变相应力比引入到统一硬化参数中, 利用统一硬化参数可以有效描述初始各向异性固结黏土在剪切加载下的剪缩与剪胀, 应变硬化及软化现象. (3)引入反映结构性胶结强度性质的胶结参量p_e, 并给出p_e随塑性偏应变的衰减演化方程, 利用胶结参量可描述结构性黏土的剪胀特性. 预测与试验结果对比表明, 所提的K₀超固结结构性模型可有效描述K₀超固结黏土的刚度提高效应, 黏土的包辛格效应, 结构性黏土胶结强度的损失现象以及结构性黏土的应变软化现象. 证明了所提模型的适用性以及合理性.      

结构性饱和黄土动力特性试验研究

基于室内不排水动三轴试验,研究了5种因素,即围压、超固结比、偏压固结比、动剪应力比、加载频率等对饱和黄土动力特性的影响。本文强调了结构性在饱和黄土动力特性研究中的重要性,结构性的破坏是影响土体动力力学特性的一个重要转折点。并阐明了用塑性残余变形来表征土体内部结构的变化并以此作为孔压增长函数自变量的合理性。     

南海水合物黏土沉积物力学特性试验模拟研究

利用自行研制的含水合物沉积物合成、分解与力学性质测量一体化试验设备,以南海水合物区域的海底粉质黏土作为骨架,制备含水合物沉积物样品,并对其进行了三轴压缩试验研究,获得了水合物分解前后的应力应变曲线和抗剪强度特性. 结果表明:在水合物饱和度0%~45% 的范围内,水合物沉积物的应力应变曲线均表现为弹塑性变形,存在明显的应变硬化现象;抗剪强度、内摩擦角和黏聚力随水合物饱和度的增加而增加. 相对而言,内摩擦角随饱和度增加幅度较小,其他参数在水合物饱和度超过25% 时,呈陡然增高趋势;水合物分解后导致抗剪强度最大可降低为初始的1/4,不同初始饱和度条件下水合物完全分解后沉积物的抗剪强度基本相等,并大于同等围压条件下初始不含水合物的沉积物抗剪强度.      

Micromechanical modeling for behavior of silty sand with influence of fine content

Silty sand is a soil mixture with coarse grains and fine grains. Experimental observations have shown that small amount of fines may reduce the undrained shear strength significantly. The purpose of this paper is to propose a micromechanical model for the stress–strain behavior of silty sand influenced by fines under drained and undrained conditions. The micromechanical stress–strain model accounts for the influence of fines on the density state of the soil mixture, thus consequently affect the critical state friction angle and the amount of sliding between particles. The present model is examined by simulating typical drained and undrained tests in conventional triaxial conditions. The simulated stress–strain curves are compared with the measured results on samples made of Ottawa sand and Foundry sand with various amounts of fines. The predictive ability of the present model for simulating the behavior of silty sand is discussed.     

正常固结饱和地基土的总应力强度指标

地基极限承载力与土体稳定分析的总应力分析法需要用土的总应力强度指标。三种常规室内三轴试验的固结应力状态、剪切时的应力路径和排水条件与地基土原位受荷破坏时不尽相同。本文首先建立三种典型排水条件下模拟地基土实际受力的总应力强度指标理论式 ,分析了其变化规律 ;与常规三轴试验结果进行了比较 ;分析了固结不排水条件下的强度计算途径和对应的指标 ;最后建立了两种部分排水条件下的总应力强度指标的计算式 ,分析了它们随固结的变化。     

A discrete element model for simulating saturated granular soil

A numerical model is developed to simulate saturated granular soil, based on the discrete element method. Soil particles are represented by Lagrangian discrete elements, and pore fluid, by appropriate discrete elements which represent alternately Lagrangian mass of water and Eulerian volume of space. Macro-scale behavior of the model is verified by simulating undrained biaxial compression tests. Micro-scale behavior is compared to previous literature through pore pressure pattern visualization during shear tests. It is demonstrated that dynamic pore pressure patterns are generated by superposed stress waves. These pore-pressure patterns travel much faster than average drainage rate of the pore fluid and may initiate soil fabric change, ultimately leading to liquefaction in loose sands. Thus, this work demonstrates a tool to roughly link dynamic stress wave patterns to initiation of liquefaction phenomena.     

Soil failure under undrained quasi-static and high speed triaxial compression test

Experiments were conducted in unsaturated silty loam and sandy loam soils under undrained conditions. Soil failure under quasi-static and high speed triaxial compression were studied. The amount of energy used in breaking soil specimens was found to be a function of soil moisture content. During undrained quasi-static triaxial compression tests, two cases of brittle failure, a general shear failure and a fragmentation were observed. The test soil specimen broke more by fragmentation than by general shear failure. During undrained high speed triaxial compression tests, the energy use for breaking the soil specimen increased with increase in loading speed up to a certain critical speed range of 4.5–5 m/s, and then it decreased. Two types of soil failure, brittle failure and plastic flow, which were a function of the loading speed, were noticed. At lower speed, dilation of shearing along a slip plane was observed. However, at higher speed, barreling of the cylindrical specimen with top and bottom conical shaped wedges, or only a single wedge with a small crack or fluidization, was observed.     

利用大型岩质滑坡形成的环境条件及重力圧密原理分析滑面形态与强度参数

大型、特大型岩质滑坡,因其体积大,范围大,且多位于高山峡谷地区,用勘探方法虽能较准确的查明滑带的位置、形态,但因极恶劣的地形条件,绝大部分在初步研究阶段,由于缺少勘探资料而不能确定滑面位置,因而也难以获得滑面的强度参数。本文从大型岩质滑坡形成的初始环境地质条件：地形条件,地貌条件,岩性条件,构造条件,河流形态,斜坡坡体结构和变形破坏特征,结合滑坡形成后的形态特征,以反馈研究的方式,分析确定大型岩质滑坡滑面的位置及形态特征,在获得滑坡滑面位置的基础上,分析、计算滑面上覆岩体重量在滑面上产生的正应力（压应力）;在获取部分滑带土的基础上,用滑坡体重力在滑面上产生的正应力,以重力压密原理在室内开展相匹配的试验,进而获得各地段相应的物理指标,在室内开展相匹配的强度试验,获得强度参数,建立滑带土孔隙比、含水量与摩擦系数、内聚力的关系,用试验获得的关系式,结合重力压密试验得到的不同部位的含水量,去分析、研究滑面的强度参数,采用传递系数法、摩根斯坦法开展相应的稳定性分析,得到的稳定性系数均大于12,与滑坡当前的变形动态较吻合。     

强震条件下双面坡变形破坏机理的振动台物理模拟试验研究

5·12汶川地震引发了数以万计的崩塌、滑坡、泥石流等地质灾害。为了研究双面坡在强震条件下的动力响应规律,本文在大量野外调查的基础上,采用振动台物理模拟试验手段,设计完成了四类11个模型试验,从改变模型的坡度和坡顶宽度、软岩硬岩结合、阶梯状坡形等角度,较系统地研究了双面坡在强震作用下的响应规律。试验结果显示：强震条件下地震水平惯性力是导致边坡破坏的主要原因; 在地震情况下边坡变形破坏表现出明显的初动破坏效应; 振动过程中双坡具有明显的共剪效应,坡面为阶梯状时其共剪效应更明显; 坡体结构为上软下硬时下部硬岩对振动具有一定的放大效应,上硬下软时坡体易整体偏移产生变形破坏。试验结论与实际情况基本符合。     

DEM SIMULATION OF LIQUEFACTION FOR GRANULAR MEDIA UNDER UNDRAINED AXISYMMETRIC COMPRESSION AND PLANE STRAIN CONDITIONS

Based on three dimensional (3D) Discrete Element Method (DEM), the paper presents simulation results of undrained tests on loose assemblies of polydisperse spheres under axisymmetric compression and plane strain conditions using a periodic cell. In the present work, undrained tests were modelled by deforming the samples under constant volume conditions. The undrained (effective) stress paths are shown to be qualitatively similar to experimental results in literature. A microscopic parameter in terms of redundancy factor (RF) is used to identify the onset of liquefaction (or temporary liquefaction), with the condition of RF equal to unity defining the transition from ’solid-like’ to ’liquid-like’ behaviour. It is found that the undrained behaviour is governed by the evolution of redundancy factor under both undrained axisymmetric compression and plane strain conditions, and a reversal of deviatoric stress in stress path for medium loose systems occurs due to the fact that the system becomes a structural mechanism (RF<1) transiently at the microscopic level during the evolution.     

An approach to analysis of single pier based on the variational principle in multi-layered soil

In this study, a variational approach to the settlement analysis of an axially loaded pier embedded in a multi-layered soil profile is presented. In this method, the soil profile and the embedded pier are divided into a number of sub-layers according to the actual number of soil layers observed in the field. The displacement shape function of each soil layer is given as a product of an exponential equation along the pier depth and the Bessel's solution in the radial direction. The displacement relationship among the layers can be derived through the transformation matrices. One of the major features of this method is that the total number of pier elements is the same as that of soil sub-layers. All the field components, such as the displacement, stress, and strain in the soil, can be calculated by closed-form solutions except that the only unknown variable is the value β which can be determined by iteration techniques. Comparisons were made with the results of finite element analysis and the field observation in pile-loaded tests.     

Elasto-plastic stress-strain theory for cohesionless soil with curved yield surfaces

An elasto-plastic stress-strain theory for cohesionless soil with curved yield surfaces is developed on the basis of soil behavior observed in laboratory tests. This theory is applicable to general three-dimensional stress conditions, but the parameters required to characterize the soil behavior can be derived entirely from results of isotropic compression and conventional drained triaxial compression tests. The theory is shown to predict soil behavior under various loading conditions with good accuracy. Of special interest is its capability of predicting soil behavior under drained as well as undrained conditions over a range of confining pressures where the behavior changes from that typical of dense sand to that typical of loose sand. Work-hardening as well as work-softening is incorporated in the theory.     

贵州关岭大寨高速远程滑坡—碎屑流研究

2010年6月28日,贵州关岭因突降暴雨发生高速远程滑坡,滑程约1.5km,体积约174.9万m³,两个村组被毁,99人遇难。滑坡区位于西南地区常见的煤系地层区,上部为灰岩、白云岩,中部为相对较缓的砂岩地层,下部为页岩、泥岩地层,局部含煤,具有上硬下软的山体地质结构和上部富水下部隔水的水文地质结构,极易形成滑坡地质灾害。从地形上看,斜坡上陡下缓,形似“靴状地形”,上部陡峭地形导致山体易于失稳,而中下部开阔伸展良好的沟谷提供了远程的运动条件,较大的势能向动能的转化,容易形成高速远程滑坡—碎屑流。6月27日和28日的降雨是触发此起特大灾害的主要原因,其24h降雨量达310mm,超过了当地近60a来的气象记录,分析表明,降雨产生的沟谷径流量是平时强降雨(100～150mm·d^-1)的沟谷径流的2倍之上,一是在滑源区砂岩裂隙岩体中形成静水压力和渗透压力,触使滑坡的失稳下滑; 二是在沟谷中产生地表径流,为碎屑流远程流动形成饱水下垫面,导致了碎屑流流动距离和速度的显著增加。近年来随着极端强降雨等灾害性天气的重现期缩短,高速远程滑坡造成的群死群伤特大地质灾害在我国呈逐渐增加趋势,应加强对这种灾害类型的调查与防范,特别是要进行滑坡安全避让范围和逃逸速度的研究。