An analysis of ductile rupture in notched bars

Ductile fracture in axisymmetric and plane strain notched tensile specimens is analyzed numerically, based on a set of elastic-plastic constitutive relations that account for the nucleation and growth of microvoids. Final material failure by void coalescence is incorporated into the constitutive model via the dependence of the yield function on the void volume fraction. In the analyses the material has no voids initially; but as the voids nucleate and grow, the resultant dilatancy and pressure sensitivity of the macroscopic plastic flow influence the solution significantly. Considering both a blunt notch geometry and a sharp notch geometry in the computations permits a study of the relative roles of high strain and high triaxiality on failure. Comparison is made with published experimental results for notched tensile specimens of high-strength steels. All axisymmetric specimens analyzed fail at the center of the notched section, whereas failure initiation at the surface is found in plane strain specimens with sharp notches, in agreement with the experiments. The results for different specimens are used to investigate the circumstances under which fracture initiation can be represented by a single failure locus in a plot of stress triaxiality vs effective plastic strain.     

6061-T6铝合金动态拉伸本构关系及失效行为

采用HMH-206高速材料试验机开展了6061-T6铝合金在0.001～100 s?1应变率范围内的静、动态拉伸力学性能实验,分析了其应力-应变响应特征和应变率敏感性,讨论了应变率对6061-T6铝合金流动应力和应变率敏感性指数的影响,并基于实验结果对Johnson-Cook本构模型进行了修正。结合缺口试件的实验结果和模拟数据,得到了材料的Johnson-Cook失效模型参数,并对模型的准确性和适用性进行了验证。结果表明,在拉伸载荷作用下,6061-T6铝合金表现出明显的应变硬化特征和应变率敏感性,其流动应力随应变率的升高而提高,修正的Johnson-Cook本构模型可以描述材料的动态塑性流动行为,建立的Johnson-Cook失效模型能够表征材料的断裂失效行为。     

Temperature dependent mechanical behaviour of PVDF: Experiments and numerical modelling

The mechanical behaviour of Polyvinylidene Fluoride (PVDF) is analysed. To this end, tensile tests are performed on both smooth and notched specimens, for several values of the notch radius in order to set specific values of the stress triaxiality ratio in the net section. Tests were performed at various temperatures and at various strain rates. Experimental data together with fracture surface examinations by SEM allow the dependence of deformation and void growth processes on strain rate and temperature to be investigated. This experimental work was carried out in order to test the mechanics of porous media model. For each investigated temperature, constitutive relations take both porosity and strain rate sensitivity into account. The model is proposed for deformation leading to crazing. The material coefficients are optimised by imposing a continuous dependence on temperature.     

Stress–strain behaviour of aluminium alloys at a wide range of strain rates

The stress–strain behaviour of extruded AA6xxx and AA7xxx aluminium alloys in T6 temper was studied at a wide range of strain rates. Tensile tests at low to medium strain rates were performed in a standard tensile test machine, while a split-Hopkinson tension bar was used to carry out tests at high rates of strain. Extruded aluminium alloys have anisotropic mechanical properties, and tests were therefore done in three directions with respect to the extrusion direction. It is found that the AA6xxx alloys exhibit no significant rate sensitivity in the stress–strain behaviour, while moderate rate sensitivity was found for the AA7xxx alloys. There seems to be no significant difference between the rate sensitivity in the three tensile directions. The experimental data were used to identify the parameters of a thermo-viscoplastic constitutive relation for the extruded alloys, which includes the effects of strain hardening, strain-rate hardening, thermal softening and plastic anisotropy.     

考虑应力三轴度影响的30CrMnSiNi2A钢韧性断裂研究

30CrMnSiNi2A钢是一种在军工领域应用广泛的低合金高强度钢。针对结构完整性的评估问题,采用试验和数值计算结合的方法研究了30CrMnSiNi2A钢的韧性断裂特性。对光滑圆棒试件在不同温度下进行准静态和动态拉伸试验,并通过有限元迭代方法标定了材料的Johnson-Cook动态本构模型参数,分析了温度和应变率对30CrMnSiNi2A钢断裂行为的影响。开展了缺口圆棒拉伸、缺口平板剪切和圆柱压缩试验,计算了各试件对应的平均应力三轴度和断裂应变,给出了应力三轴度在?1/3～1.5区间内的断裂应变变化曲线,分别确定了Johnson-Cook和Bao-Wierzbicki失效模型参数。研究表明,30CrMnSiNi2A钢的断裂应变与应力状态密切相关,且在不同的应力三轴度区间内曲线单调性差异较大,Bao-Wierzbicki失效模型较好地描述了这种钢在不同应力状态下的断裂特性。     

A study of localisation in dual-phase high-strength steels under dynamic loading using digital image correlation and FE analysis

Tensile tests were conducted on dual-phase high-strength steel in a Split-Hopkinson Tension Bar at a strain-rate in the range of 150–600/s and in a servo-hydraulic testing machine at a strain-rate between 10^?3 and 10⁰/s. A novel specimen design was utilized for the Hopkinson bar tests of this sheet material. Digital image correlation was used together with high-speed photography to study strain localisation in the tensile specimens at high rates of strain. By using digital image correlation, it is possible to obtain in-plane displacement and strain fields during non-uniform deformation of the gauge section, and accordingly the strains associated with diffuse and localised necking may be determined. The full-field measurements in high strain-rate tests reveal that strain localisation started even before the maximum load was attained in the specimen. An elasto-viscoplastic constitutive model is used to predict the observed stress–strain behaviour and strain localisation for the dual-phase steel. Numerical simulations of dynamic tensile tests were performed using the non-linear explicit FE code LS-DYNA. Simulations were done with shell (plane stress) and brick elements. Good correlation between experiments and numerical predictions was achieved, in terms of engineering stress–strain behaviour, deformed geometry and strain fields. However, mesh density plays a role in the localisation of deformation in numerical simulations, particularly for the shell element analysis.     

5083H111铝合金宽应变率拉伸动态本构模型

结合5083H111铝合金较宽应变率范围2×10-4 ~ 4×102s-1内的拉伸实验数据,揭示该铝合金的拉伸“V”型率效应特征,分析对数应变率敏感系数λ和切线模量Et的应变率和应变相关性,进而通过对Johnson-Cook模型的修正来建立合理描述5083H111铝合金较宽应变率范围内的动态拉伸本构模型。建立的动态本构模型中,流动应力包括应变率相关和应变相关两部分。该模型合理描述了5083H111铝合金的拉伸“V”型率效应特征,预测结果与实验结果较为一致。另外,结合破坏应变的对数应变率敏感系数β,得到了拉伸破坏应变预测方程,其预测结果也与实验结果基本一致。     

应力三轴度的有限元计算修正

对某高强度钢制成的光滑圆棒和缺口圆棒进行了系列准静态拉伸实验,采用ABAQUS对每个试 件进行了数值模拟,得到了该材料的真实应力应变曲线,拟合出了J-C本构模型和失效模型的部分材料常数。 最后,对该高强度钢制成的平板进行了撞击实验,并用得到的J-C模型对平板撞击实验进行了数值模拟,计算 结果与实验结果吻合很好,证明利用数值模拟并修正应力三轴度的方法是可行的。     

On the influence of stress triaxiality and strain rate on the behaviour of a structural steel. Part II. Numerical study

Non-linear finite element analyses of quasi-static and high-rate tensile tests with smooth and notched axisymmetric specimens of the structural steel Weldox 460 E have been carried out. The constitutive relation and fracture criterion of Johnson and Cook, which were adopted in the simulations, have previously been determined for Weldox 460 E steel. First, a validation study was completed to assess the accuracy of the constitutive relation and fracture criterion. The numerical results were compared with experimental data from tensile tests under quasi-static and dynamic loading conditions. Secondly, the use of Bridgman's analysis in the identification of the fracture criterion was evaluated, and the influence of adiabatic heating and inertia on the stress triaxiality in the tensile specimens was investigated. The results were finally used to discuss the identification of fracture criteria based on tensile tests with smooth and notched axisymmetric specimens.     

Elasto-visco-plastic modeling of mild steels for sheet forming applications over a large range of strain rates

A physically based elasto-visco-plastic constitutive model is presented and compared to experimental results for three different mild steels. The experiments consist of tensile tests ranging from quasi-static conditions up to strain rates of 10³ s^?1 as well as quasi-static simple and reverse shear tests at different amounts of pre-strain. Additional two-step sequential mechanical tests (Bauschinger and orthogonal effects) have been performed to further evaluate the ability of the model to describe strain-path changes at moderate/large strains. The model requires significantly fewer material parameters compared to other visco-plasticity models from the literature, while being able to describe some of the main features of the strain-rate sensitivity of mild steels. Accordingly, the parameter identification is simple and intuitive, requiring a relatively small set of experiments. The strain-rate sensitivity modeling is not restricted to a particular hardening law and thus provides a general framework in which advanced hardening equations can be adopted.     

基于应力三轴度和罗德参数的6061和7075铝合金材料断裂失效分析

分别对6061铝合金和7075铝合金材料的缺口圆棒试件和凹槽平板试件进行准静态拉伸试验,并采用ABAQUS软件对拉伸过程进行数值模拟。模拟结果与试验测试结果吻合很好,验证了有限元模型的合理性和可靠性。通过有限元模拟,分别给出了不同试件的应力三轴度和罗德参数随等效塑性应变的变化曲线以及两种材料的失效轨迹,并对它们进行了分析讨论。结果表明:形状相同、材料性质不同的试件,应力三轴度的演化规律不同;材料的失效应变受应力三轴度和罗德参数的影响,并且不同性质的材料对罗德参数的敏感性不同。     

Anisotropic responses, constitutive modeling and the effects of strain-rate and temperature on the formability of an aluminum alloy

Finite deformation anisotropic responses of AA5182-O, over a wide range of strain-rates (10⁻⁴ to 10⁰ s⁻¹) and temperatures (293-473 K) are presented. The plastic anisotropy parameters were experimentally determined from tensile experiments using specimens from sheet material. Using the experimental results under plane stress conditions, the anisotropy coefficients for Barlat’s yield function (YLD96) were calculated at different strain-rates and temperatures. The correlations obtained from YLD96 are in good agreement with the observed experimental results. The strain-rate sensitivity of AA5182-O alloy changed from negative at 293 K to positive at 473 K. Khan-Huang-Liang (KHL) constitutive model is shown to correlate the observed strain-rate and temperature dependent responses reasonably well. The material parameters were obtained from the experimental responses along the rolling direction (RD) of the sheet. Marciniak and Kuckzinsky (M-K) theory was used to obtain the theoretical strain and stress-based forming limit curves (FLCs) at different strain-rates and temperatures. The experimental result from the published literature is compared with the FLCs from the current study.     

A finite-deformation constitutive model for bulk metallic glass composites

The focus of this study is the development of an elastic-viscoplastic, three-dimensional, finite-deformation constitutive model to describe the large deformation behavior of bulk metallic glass (BMG) composite. A macroscopic theoretical formulation is proposed based on thermodynamic considerations to describe the response at ambient temperature and pressure, as well as at different strain rates. A constitutive equation is derived using the principle of thermodynamics and the augmenting of free energy. This is done by assuming that deformation within the constituent phases of the composite is affine; kinetic equations defining plastic shear and evolution of free volume concentration are then derived. The constitutive model is subsequently implemented in a finite-element program (Abaqus/Explicit) via a user-defined material subroutine. Numerical predictions are compared with experimental results from tests on La-based in situ BMG composite (La–Al–Cu–Ni) specimens cast in-house; this demonstrates that the model is able to describe the material behavior observed.     

A 3-phase model for the numerical analysis of semi-crystalline polymer films in finite elastoplastic strains

In this paper, the mechanical behavior of semi-crystalline polymer films in finite elastoplastic strains is investigated. A 3-phase constitutive model has been specially developed in a previous paper and validated for various materials in both uniaxial and biaxial uniform hot drawing. In the present study, the numerical implementation of this 3-phase model in a finite element software is outlined in the perspective of using this model in more general non-uniform cases of complex geometries and/or loadings. In the present case, only polyethylene films at room temperature are considered. First, uniaxial tensile experimental tests are performed so as to calibrate the model parameters. Then, for validation purposes, two series of experimental tests are conducted on tensile specimens with central holes and double edge notched tensile (DENT) specimens. During these tests, digital image correlation is used to analyze the strain (or displacement) field history during loading. Finally, numerical computations are performed with the help of the finite element software including the 3-phase model previously implemented (cohesive elements are also needed for the simulation of the crack propagation in DENT specimens). In both cases, the comparison between the experimental and numerical force–displacement curves, together with the comparisons between the experimental and numerical strain fields at different times, give very satisfactory results.     

Strain-rate effects in rheological models of inelastic response

Stress–strain response under constant and variable strain-rate is studied for selected models of inelastic behavior. The derived closed-form solutions for uniaxial loading enable simple evaluation of the strain-rate effects on the material response. The effect of an abrupt change of strain-rate is also examined. Non-Newtonian viscosity which decreases with an increasing strain-rate is incorporated in the analysis. Parabolic and hyperbolic hardening are used to describe the plastic response in monotonic loading. A three-dimensional generalization of an elastic–viscoplastic model is employed to study the stress relaxation in simple shear. A combined isotropic–kinematic hardening and the concept of overstress are used in the analysis. The unloading nonlinearity of the stress–strain curve is then discussed.     

Influence of void nucleation on ductile shear fracture at a free surface

An approximate continuum model of a ductile, porous material is used to study the influence of the nucleation and growth of micro-voids on the formation of shear bands and the occurrence of surface shear fracture in a solid subject to plane strain tension. Bifurcation into diffuse modes is analysed for a plane strain tensile specimen described by these constitutive relations, which account for a considerable plastic dilatancy due to void growth and for the possibility of non-normality of the plastic flow law. In particular, bifurcation into surface wave modes and the possible influence of such modes triggering shear bands is investigated. For solids with initial imperfactions such as a surface undulation, a local material inhomogeneity on an inclusion colony, the inception and growth of plastic flow localization is analysed numerically. Both the formation of void-sheets and the final growth of cracks in the shear bands is described numerically. Some special features of shear band development in the solid obeying non-normality are studied by a simple model problem.     

Application of digital image correlation to the study of planar anisotropy of sheet metals at large strains

The aim of this work is to measure and model the planar anisotropy of thin steel sheets. The experimental data have been collected using the digital image correlation technique. This is a powerful tool to measure the strain field on differently shaped specimens subjected to large plastic deformations. In this manner, it is possible to observe the material behaviour under different stress-strain states, from small to large deformation conditions, on the entire specimen surface. The experimental results on smooth and notched samples have been used to characterize the flow stress curve after necking and a nonassociated plastic flow rule is proposed to describe the anisotropic behaviour of the material. To compare the experimental data with the predictions of the adopted constitutive model, a novel method, based on the image correlation results, has been implemented.     

A quasi-flow constitutive model with strain-rate dependence

In this paper, the proposed is a quasi-flow constitutive model with strain-rate sensitivity for elastic plastic large deformation. The model is based on the Quasi-flow Corner theory, and is suitable for the sheet metal forming process simulation with a variable punch machine velocity. Uniaxial tensile tests and deep-drawing tests of a circular blank with square punch are carried out and numerically simulated. The consistency between the experimental and the numerically simulated results shows the validity of the present new constitutive model. The project supported by the Scientific Foundation of National Outstanding Youth of China (10125208), the National Natural Science Foundation of China (19832020), and the National Education Committee of China