Analytical and numerical solutions of the problem of gravity-induced mixing of a light layer using the <Emphasis Type="Italic">k</Emphasis>–<Emphasis Type="Italic">ε</Emphasis> turbulence model

An analytical solution for the self-similar stage in the problem of gravity-induced turbulent mixing in a light (heavy) layer is obtained on the basis of the k–ε model equations. The solution obtained is compared with the results of a numerical investigation of the problem using both three-dimensional direct numerical simulation and the k–ε model. The calculations were performed using the two- and three-dimensional versions of the EGAK method. The results of all the calculations and the available experimental data are in reasonable agreement.     

Flutter analysis of a viscoelastic tapered wing under bending–torsion loading

The dynamic stability of a tapered viscoelastic wing subjected to unsteady aerodynamic forces is investigated. The wing is considered as a cantilever tapered Euler–Bernoulli beam. The beam is made of a linear viscoelastic material where Kelvin–Voigt model is assumed to represent the viscoelastic behavior of the material. The governing equations of motion are derived through the extended Hamilton’s principle. The resulting partial differential equations are solved via Galerkin’s method along with the classical flutter investigation approach. The developed model is validated against the well-known Goland wing and HALE wing and good agreement is obtained. Different solution methods, namely; the k method, the p-k method, and the flutter determinant method are compared for the case of elastic wing. However, when the viscoelastic damping is introduced, the k and p-k methods become less effective. The flutter determinant method is modified and employed to carry out non-dimensional parametric study on the Goland wing. The study includes the effects of parameters such as the taper ratio, the density ratio, the viscoelastic damping of wing structure and many other parameters on the flutter speed and flutter frequency. The study reveals that a tapered wing would be more dynamically stable than a uniform wing. It is also observed that the viscoelastic damping provides wider stability region for the wing. The investigation shows that the density ratio, bending-to-torsion frequency ratio, and the radius of gyration have significant effects on the dynamic stability of the wing. Based on the obtained results, a wing with an elastic center and inertial center that are located closer to the mid-chord would be more dynamically stable.     

Experimental and Theoretical Sensitivity Analysis of Turbulent Flow Past a Square Cylinder

The Siemens SGT-800 3^rd generation DLE burner fitted to an atmospheric combustion rig has been numerically investigated. Pure methane and methane enriched by 80 vol% hydrogen flames have been considered. A URANS (Unsteady Reynolds Averaged Navier-Stokes) approach was used in this study along with the k ? ω SST and the k ? ω SST-SAS models for the turbulence transport. The chemistry is coupled to the turbulent flow simulations by the use of a laminar flamelet library combined with a presumed PDF. The effect of the mesh density in the mixing and the flame region and the effect of the turbulence model and reaction rate model constant are first investigated for the methane/air flame case. The results from the k ? ω SST-SAS along with flamelet libraries are shown to be in excellent agreement with experimental data, whereas the k ? ω SST model is too dissipative and cannot capture the unsteady motion of the flame. The k ? ω SST-SAS model is used for simulation of the 80 vol% hydrogen enriched flame case without further adjusting the model constants. The global features of the hydrogen enrichment are very well captured in the simulations using the SST-SAS model. With the hydrogen enrichment the time averaged flame front location moves upstream towards the burner exit nozzle. The results are consistent with the experimental observations. The model captures the three dominant low frequency unsteady motion observed in the experiments, indicating that the URANS/LES hybrid model indeed is capable of capturing complex, time dependent, features such as an interaction between a PVC and the flame front.     

Understanding and Modelling Turbulence Over and Inside Porous Media

To understand turbulence over porous media, a series of PIV measurements were carried out in porous-walled channel flows. The porous walls were made of three types of foamed ceramics which had the same porosity but different permeability. For turbulence inside porous media, LES studies of fully developed flows in three different model porous media were performed. Referring to these databases, a multi-scale k ? ε four equation eddy viscosity model for turbulence around and/or inside porous media was developed. Through the comparison to the experimental results, the proposed model was validated with satisfactory accuracy.     

Numerical simulation of the interaction of a transverse jet with a supersonic flow using different turbulence models

This paper presents a numerical simulation of the flow resulting from transverse jet injection into a supersonic flow through a slot nozzle at different pressures in the injected jet and the crossflow. Calculations on grids with different resolutions use the Spalart–Allmaras turbulence model, the k–ε model, the k–ω model, and the SST model. Based on a comparison of the calculated and experimental data on the wall pressure distribution, the length of the recirculation area, and the depth of jet penetration into the supersonic flow, conclusions are made on the accuracy of the calculation results for the different turbulence models and the applicability of these models to similar problems.     

Vortical structures behind a transverse jet in a supersonic flow at high jet to crossflow pressure ratios

A three-dimensional supersonic turbulent flow with symmetric normal injection of circular jets from the channel walls is numerically simulated. The initial Favre-averaged Navier–Stokes equations closed by the k–ω turbulence model are solved by an algorithm based on an ENO scheme. The mechanism of the formation of vortical structures due to the interaction of the jet with the free stream is studied for jet to crossflow total pressure ratios ranging from 3 to 50. It is known from experiments reported in the literature that, for n ? 10, mixing of the jet with the high-velocity flow leads to the formation of a pair of vortices and of an additional separation zone near the wall behind the jet. It is demonstrated that the present numerical results are consistent with such findings and that the pressure distribution on the wall ahead of the jet in the plane of symmetry is also in reasonable agreement with available experimental data.     

Spray-Flame Dynamics in a Rich Droplet Array

We numerically study spray-flame dynamics. The initial state of the spray is schematized by alkane droplets located at the nodes of a face-centered 2D-lattice. The droplets are surrounded by a gaseous mixture of alkane and air. The lattice spacing s reduced by the combustion length scale is large enough to consider that the chemical reaction occurs in a heterogeneous medium. The overall spray equivalence ratio is denoted by ?_T, with ?_T = ?_L + ?_G, where ?_G corresponds to the equivalence ratio of the gaseous surrounding mixture at the initial saturated partial pressure, while ?_L is the so-called liquid loading. To model such a heterogenous combustion, the retained chemical scheme is a global irreversible one-step reaction governed by an Arrhenius law, with a modified heat of reaction depending on the local equivalence ratio. ?_T is chosen in the range 0.9 ≤ ?_T ≤ 2. Three geometries (s = 3, s = 6, s = 12) and four liquid loadings, ?_L = 0.3, ?_L = 0.5, ?_L = 0.7, ?_L = 0.85 are studied. In the rich sprays, our model qualitatively retrieves the recent experimental measurements: the rich spray-flames can propagate faster than the single-phase flames with the same overall equivalence ratio. To analyse the conditions for this enhancement, we introduce the concept of “spray Peclet number”, which compares the droplet vaporization time with the combustion propagation time of the single-phase flame spreading in the fresh surrounding mixture.     

Application of the γ-Reθ Transition Model to Simulations of the Flow Past a Circular Cylinder

Based on the finite volume method, the flow past a two-dimensional circular cylinder at a critical Reynolds number (Re = 8.5 × 10⁵) was simulated using the Navier-Stokes equations and the γ-Re_θ transition model coupled with the SST k ? ω turbulence model (hereinafter abbreviated as γ-Re_θ model). Considering the effect of free-stream turbulence intensity decay, the SST k ? ω turbulence model was modified according to the ambient source term method proposed by Spalart and Rumsey, and then the modified SST k ? ω turbulence model is coupled with the γ-Re_θ transition model (hereinafter abbreviated as γ-Re_θ-SR model). The flow past a circular cylinder at different inlet turbulence intensities were simulated by the γ-Re_θ-SR model. At last, the flow past a circular cylinder at subcritical, critical and supercritical Reynolds numbers were each simulated by the γ-Re_θ-SR model, and the three flow states were analyzed. It was found that compared with the SST k ? ω turbulence model, the γ-Re_θ model could simulate the transition of laminar to turbulent, resulting in better consistency with experimental result. Compared with the γ-Re_θ model, for relatively high inlet turbulence intensities, the γ-Re_θ-SR model could better simulate the flow past a circular cylinder; however the improvement almost diminished for relatively low inlet turbulence intensities The γ-Re_θ-SR model could well simulate the flow past a circular cylinder at subcritical, critical and supercritical Reynolds numbers.     

Multipulse Phases in k-Mixtures of Bose–Einstein Condensates

For the system

$-\Delta U_i+ U_i=U_i^3-\beta U_i\sum_{j\neq i}U_j^2,\quad i=1,\dots,k,$

(with k ≧ 3), we prove the existence for β large of positive radial solutions on \({\mathbb R^N}\) . We show that as β →  + ∞, the profile of each component U _i separates, in many pulses, from the others. Moreover, we can prescribe the location of such pulses in terms of the oscillations of the changing-sign solutions of the scalar equation  ? ΔW  +  W  =  W³. Within an Hartree–Fock approximation, this provides a theoretical indication of phase separation into many nodal domains for the k-mixtures of Bose–Einstein condensates.

     

Reynolds-Averaged,Scale-Adaptive and Large-Eddy Simulations of Premixed Bluff-Body Combustion Using the Eddy Dissipation Concept

A lean premixed propane/air bluff-body stabilized flame (Volvo test rig) is calculated using the Scale-Adaptive Simulation turbulence model (SAS) and Large-Eddy simulations (LES) as well as the conventional Reynolds-averaged approach (RAS). RAS and SAS are closed by the standard k-?? and the k-ω Shear Stress Transport (SST) turbulence models, respectively. The conventional Smagorinsky and the k-equation sub-grid scales models are used for the LES closure. Effects of the sub-grid scalar flux modeling using the classical gradient hypothesis and Clark’s tensor diffusivity closures both for the inert and reactive LES flows are discussed. The Eddy Dissipation Concept (EDC) is used for the turbulence-chemistry interaction. It assumes that molecular mixing and the subsequent combustion occur in the ’fine structures’ (smaller dissipative eddies, which are close to the Kolmogorov scales). Assuming the full turbulence energy cascade, the characteristic length and velocity scales of the ’fine structures’ are evaluated using different turbulence models (RAS, SAS and LES). The finite-rate chemical kinetics is taken into account by treating the ’fine structures’ as constant pressure and adiabatic homogeneous reactors, calculated as a system of ordinary-differential equations (ODEs) described by a Perfectly Stirred Reactor (PSR) concept. Several further enhancements to model the PSRs are proposed, including a new Livermore Solver (LSODA) for integrating stiff ODEs and a new correction to calculate the PSR time scales. All models have been implemented as a stand-alone application \(\text {edcPisoFoam}\) based on the OpenFOAM technology. Additionally, several RAS calculations were performed using the Turbulence Flame Speed Closure model in Ansys Fluent to assess effects of the heat losses by modeling the conjugate heat transfer between the bluff-body and the reactive flow. Effects of the turbulence Schmidt number on RAS results are discussed as well. Numerical results are compared with available experimental data. Reasonable consistency between experimental data and numerical results provided by RAS, SAS and LES is observed. In general, there is satisfactory agreement between present LES-EDC simulations, numerical results by other authors and measurements without any major modification to the EDC closure constants, which gives a quite reasonable indication on the adequacy and accuracy of the method and its further application for turbulent premixed combustion simulations.     

Dual yielding in capillary suspensions

Rheological measurements were performed to examine the yielding behavior of capillary suspensions prepared by mixing cocoa powder as dispersed phase, vegetable oil as the continuous primary fluid, and water as the secondary fluid. Here, we investigated the yielding behavior of solid-fluid-fluid systems with varying particle volume fraction, ?, spanning the regime from a low volume fraction (? = 0.25) to a highly filled regime (? = 0.65) using dynamic oscillatory measurements. While for ? ≤ 0.4 with a fixed water volume fraction (? _w ) of 0.06 as the secondary fluid, capillary suspensions exhibited a single yield point due to rupturing of aqueous capillary bridges between the particles, while capillary suspensions with ? ≥ 0.45 showed a two-step yielding behavior. On plotting elastic stress (G^′ γ) as a function of applied strain (γ), two distinct peaks, indicating two yield stresses, were observed. Both the yield stresses and storage modulus at low strains were found to increase with ? following a power law dependence. With increasing ? _w (0 – 0.08) at a fixed ? = 0.65, the system shifted to a frustrated, jammed state with particles strongly held together shown by rapidly increasing first and second yield stresses. In particular, the first yield stress was found to increase with ? _w following a power law dependence, while the second yield stress was found to increase exponentially with ? _w . Transient steady shear tests were also performed. The single stress overshoot for ? ≤ 0.4 with ? _w = 0.06 reflected one-step yielding behavior. In contrast, for high ? (≥ 0.45) values with ? _w = 0.06, two stress overshoots were observed in agreement with the two-step yielding behavior shown in the dynamic oscillatory measurements. Experiments on the effect of resting time on microstructure recovery demonstrated that aggregates could reform after resting under quiescent conditions.     

Assessment of Five SGS Models for Low-Rem MHD Turbulence

Assessment of three regularization-based and two eddy-viscosity-based subgrid-scale (SGS) turbulence models for large eddy simulations (LES) are carried out in the context of magnetohydrodynamic (MHD) decaying homogeneous turbulence (DHT) with a Taylor scale Reynolds number (Re_λ) of 120 and a MHD transition-to-turbulence Taylor-Green vortex (TGV) problems with a Reynolds number of 3000, through direct comparisons to direct numerical simulations (DNS). Simulations are conducted using the low-magnetic Reynolds number approximation (Re_m<<1). LES predictions using the regularization-based Leray- α,LANS- α, and Clark- α SGS models, along with the eddy viscosity-based non-dynamic Smagorinsky and the dynamic Smagorinsky models are compared to in-house DNS for DHT and previous results for TGV. With regard to the regularization models, this work represents their first application to MHD turbulence. Analyses of turbulent kinetic energy decay rates, energy spectra, and vorticity fields made between the varying magnetic field cases demonstrated that the regularization models performed poorly compared to the eddy-viscosity models for all MHD cases, but the comparisons improved with increase in magnitude of magnetic field, due to a decrease in the population of SGS eddies within the flow field.     

Effects of Fuel Lewis Number on Localised Forced Ignition of Globally Stoichiometric Stratified Mixtures: a Numerical Investigation

The influences of fuel Lewis number Le_F on localised forced ignition of globally stoichiometric stratified mixtures have been analysed using three-dimensional compressible Direct Numerical Simulations (DNS) for cases with Le_F ranging from 0.8 to 1.2. The globally stoichiometric stratified mixtures with different values of root-mean-square (rms) equivalence ratio fluctuation (i.e. ?^′= 0.2, 0.4 and 0.6) and the Taylor micro-scale l_? of equivalence ratio ? variation (i.e. l_?/l_f= 2.1, 5.5 and 8.3 with l_f being the Zel’dovich flame thickness of the stoichiometric laminar premixed flame) have been considered for different initial rms values of turbulent velocity u^′. A pseudo-spectral method is used to initialise the equivalence ratio variation following a presumed bi-modal distribution for prescribed values of ?^′ and l_?/l_f for global mean equivalence ratio 〈?〉=1.0. The localised ignition is accounted for by a source term in the energy transport equation that deposits energy for a stipulated time interval. It has been observed that the maximum values of temperature and the fuel reaction rate magnitude increase with decreasing Le_F during the period of external energy deposition. The initial values of Le_F, u^′/S_b(?=1), ?^′ and l_?/l_f have been found to have significant effects on the extent of burning of the stratified mixtures following localised ignition. For a given value of u^′/S_b(?=1), the extent of burning decreases with increasing Le_F. An increase in u^′ leads to a monotonic reduction in the burned gas mass for all values of Le_F in all stratified mixture cases but an opposite trend is observed for the Le_F=0.8 homogeneous mixture. It has been found that an increase in ?^′ has adverse effects on the burned gas mass, whereas the effects of l_?/l_f on the extent of burning are non-monotonic and dependent on ?^′ and Le_F. Detailed physical explanations have been provided for the observed Le_F, u^′/S_b(?=1), ?^′ and l_?/l_f dependences.     

Mechanical Properties of Hard W-C Coating on Steel Substrate Deduced from Nanoindentation and Finite Element Modeling

Mechanical properties of a hard and stiff W-C coating on steel substrate have been investigated using nanoindentation combined with finite element modeling (FEM) and extended FEM (XFEM). The significant pile-up observed around the indents in steel substrate caused an overestimation of hardness and indentation modulus. A simple geometrical model, considering the additional contact surfaces due to pile-up, has been proposed to reduce this overestimation. The presence of W-C coating suppressed the pile-up in the steel substrate and a transition to sink-in behavior occurred. The FEM simulations adequately reproduced the surface topography of the indents in the substrate and coating/substrate systems as well. The maximum principal stresses of the indented W-C/steel coated system were tensile; they were always located in the coating and evolved in 3 stages. Cohesive cracking occurred during loading in the sink-in zone (stage III) when the ultimate tensile strength (σ _max ) of the coating was reached. The obtained hardness (H _c ), indentation modulus (E _c ), yield stress (Y) and strength (σ _max ) of the W-C coating were H _c ? =?20 GPa, E _c ? =?250 GPa, Y?=?9.0 GPa and σ _max ? =?9.35 GPa, respectively. XFEM resulted in fracture energy of the W-C coating of G?=?38.1 J?·?m^-2 and fracture toughness of K _IC ? =?3.5 MPa?·?m^0.5.     

Effective viscosity of a dilute emulsion of spherical drops containing soluble surfactant

The effective viscosity of a dilute emulsion of spherical drops containing a soluble surfactant is calculated under a linear creeping flow. It is assumed that convection of surfactant is small relative to diffusion, and thus the Peclet number, Pe, is small. We calculate the effective viscosity of the emulsion to \(\mathcal {O}(Pe\phi \mu )\), where ? is the small volume fraction of the dispersed drops and μ is the viscosity of the surfactant-free suspending fluid. This \(\mathcal {O}(Pe\phi \mu )\) contribution is a sensitive function of the bulk and interfacial surfactant transport. Specifically, soluble surfactant molecules diffuse from the bulk to the interface and then adsorb to the interface. The ratio of the time scale for bulk diffusion to the time scale for adsorption to the interface is quantified by a Damkohler number, Da. The adsorption of surfactant to the interface may cause a significant decrease in the bulk concentration, which is known as depletion. The impact of depletion is characterized by two parameters: h, which is a dimensionless depletion depth; and k, which is the ratio of the desorption time scale to the adsorption time scale. We analytically determine how the \(\mathcal {O}(Pe\phi \mu )\) contribution to the effective viscosity depends on h, k, and Da. Surprisingly, for certain regimes in the h ? k ? Da parameter space, we predict the effective viscosity of the emulsion to be greater than Einstein’s result for the viscosity of a suspension of rigid spheres. Large Marangoni stresses driven by convective transport of soluble surfactant molecules are responsible for this result.     

Control of the aerodynamic characteristics of a profile oscillating with respect to the incidence angle in subsonic viscous flow

The results of a numerical simulation of the unsteady subsonic viscous gas flow around a two-dimensional profile oscillating with respect to the incidence angle are presented and the possibility of controlling the nonstationary aerodynamic characteristics is considered. The hysteresis phenomena typical of oscillatory profile motions are investigated, the dependence of the lift force and drag is found for various laws of periodic variation of the incidence angle with time, and the effect of the frequency and amplitude of the angular profile oscillations on the shape of the hysteresis curves is studied. The calculations were based on the numerical solution of the nonstationary Navier-Stokes equations averaged in the Reynolds sense (Reynolds equations) which were closed using the k-ω turbulence model with modeling of the laminar/turbulent transition.     

Numerical Simulation of Two Phase Turbulent Flow of Nanofluids in Confined Slot Impinging Jet

In this article, a numerical investigation is performed on flow and heat transfer of confined impinging slot jet, with a mixture of water and Al₂O₃ nanoparticles as the working fluid. Two-dimensional turbulent flow is considered and a constant temperature is applied on the impingement surface. The k ? ω turbulence model is used for the turbulence computations. Two-phase mixture model is implemented to study such a flow field. The governing equations are solved using the finite volume method. In order to consider the effect of obstacle angle on temperature fields in the channel, the numerical simulations were performed for different obstacle angles of 0° ? 60°. Also different geometrical parameters, volume fractions and Reynolds numbers have been considered to study the behavior of the system in terms of stagnation point, average and local Nusselt number and stream function contours. The results showed that the intensity and size of the vortex structures depend on jet- impingement surface distance ratio (H/W) and volume fraction. The maximum Nusselt number occurs at the stagnation point with the highest values at about H/W = 1. Increasing obstacle angle, from 15° to 60°, enhances the heat transfer rate. It was also revealed that the minimum value of average Nusselt number occurs in higher H/W ratios with decreasing the channel length.     

Combining the SSG/LRR-<Emphasis Type="Italic">ω</Emphasis> differential reynolds stress model with the detached eddy and laminar-turbulent transition models

The procedure of incorporating the detached eddy method and a model of laminar-turbulent transition into the SSG/LRR-ω turbulence model is presented. The approach proposed can be regarded as the generalization of the existing models intended to perform calculations with the SST turbulence model to the case of their use with the SSG/LRR-ω model. The advantage of the approach developed over the RANS turbulence models based on the Boussinesq hypothesis is demonstrated with respect to the problems of flow past an airfoil and cold jet outflow.     

Numerical Simulation of the Negative Magnus Effect of a Two-Dimensional Spinning Circular Cylinder

Based on the finite volume method, the flow past a spinning circular cylinder at a low subcritical Reynolds number (Re =1 × 10 ⁵), high subcritical Reynolds number (Re =1.3 ×10 ⁵), and critical Reynolds number (Re =1.4 ×10 ⁵) were each simulated using the Navier-Stokes equations and the γ-Re _?? transition model coupled with the SST k?ω turbulence model. The system was solved using an implicit algorithm. The freestream turbulence intensity decay was effectively controlled by the source term method proposed by Spalart and Rumsey. The variations in the Magnus force as a function of the spin ratio, α were obtained for the three Reynolds numbers, and the flow mechanism was analyzed. The results indicate that the asymmetric transitions induced by spin affect the asymmetric separations at the top and bottom surfaces of the circular cylinder, which further affects the pressure distributions at the top and bottom surfaces of the circular cylinder and ultimately result in a negative Magnus force, whose direction is opposite to that of the classical Magnus force. This study is the first to use a numerical simulation method to predict a negative Magnus force acting on a spinning circular cylinder. At the low subcritical Reynolds number, the Magnus force remained positive for all spin ratios. At the high subcritical Reynolds number, the sign of the Magnus force changed twice over the range of the spin ratio. At the critical Reynolds number, the sign of the Magnus force changed only once over the range of the spin ratio. For relatively low spin ratios, the Magnus force significantly differed by Reynolds number; however, this variation diminished as the spin ratio increased.     

Superconvergence analysis of bi-<Emphasis Type="Italic">k</Emphasis>-degree rectangular elements for two-dimensional time-dependent Schrödinger equation

Superconvergence has been studied for long, and many different numerical methods have been analyzed. This paper is concerned with the problem of superconvergence for a two-dimensional time-dependent linear Schrödinger equation with the finite element method. The error estimate and superconvergence property with order O(h^k+1) in the H¹ norm are given by using the elliptic projection operator in the semi-discrete scheme. The global superconvergence is derived by the interpolation post-processing technique. The superconvergence result with order O(h^k+1 + τ²) in the H¹ norm can be obtained in the Crank-Nicolson fully discrete scheme.