有效集法在数学规划加权残值法中的应用

本文研究有效集法在数学规划加权残值法求解微分方程问题中的应用。从理论上和实际应用方面 阐明，对于数学规划加权残值法和线性规划问题，有效集法比常用的单纯形法更简便、易程序化、计算速度更快，因此更适用于数学规划加权残值法求解微分方程问题。     

化学跑合对齿轮胶合的影响

选用了３ 种跑合剂在ＣＬ－１００ 型齿轮试验机上进行满载跑合能力对比试验和齿轮抗胶合载荷级对比试验．结果表明：材质为４５＃ 钢的试验齿轮副和材质为２０ＣｒＭｎＴｉ钢的试验齿轮副用含磨料跑合剂进行１ 次满载跑合试验时,发生严重胶合;而采用化学跑合剂可以实现１ 次满载跑合,且用化学跑合剂跑合后的齿面比用普通油跑合后的齿面抗胶合能力提高１ 个载荷级,显示化学跑合剂在齿轮中的应用很有潜力．     

连通容器泄爆过程的影响因素

以甲烷/空气混合物为研究对象,开展了连通容器气体泄爆影响因素的实验研究。结果表明:连通容器泄爆片泄爆时,随着破膜压力和量纲一泄压比的减小,大、小球容器的最大泄爆压力均增大;在等量纲一泄压比条件下,随着连接管道长度的增加,传爆容器的最大泄爆压力增大。连通容器无膜泄爆时,大球点火条件下,无论管长如何,起爆容器和传爆容器均比单个容器最大泄爆压力大。小球点火条件下,当管道长度为0.45 m时,起爆容器和传爆容器的最大泄爆压力均小于单个容器。连通容器无膜泄爆且量纲一泄压比相同时,当管道长度为0.45 m时,大、小容器内的最大泄爆压力基本相等;当管道长度为2.45 m时,大容器点火时,传爆容器最大爆炸压力大于起爆容器,但小容器点火时,起爆容器最大泄爆压力大于传爆容器;当管道长度为4.45和6.45 m时,传爆容器最大泄爆压力均大于起爆容器。     

Response of glass-fiber-reinforced epoxy specimens to high rates of tensile loading

The object of this investigation is to establish experimentally the mechanical properties, and the mode of failure of glass-fiber-reinforced epoxy plates subjected to high rates of strain (30,000 in./in./min), in the direction of the fibers, on a specially designed impact-loading machine propelled by explosives. The results are correlated with those obtained by testing glass-fiber-reinforced epoxy plates subjected to various low rates of strain (0.0265 in./in./min, 0.66 in./in./min and 26.5 in./in./min).     

Prefacein：in dedication to Professors Yong Jin and Zhiqing Yu

This special issue of China PARTICUOLOGY is dedicated to Professors Yong Jin and Zhiqing Yu of Tsinghua University, China, to celebrate over five decades of their careers in chemical engineering research and education. Prof. Jin graduated in 1959 from Ural Polytechnic College in Svivdelovsk in the former USSR and then completed his post-graduate studies in Tianjin University in China in 1960. Thereafter, he taught at the Chinese University of Science and Technology for 13 years before joining Tsinghua University in 1973. Prof. Yu graduated in 1956 from Tianjin University in China and joined Tsinghua University thereafter. Between 1957 and 1959, Prof. Yu undertook more studies in Moscow Mendeleev Institute of Chemical Technology in the former USSR. During the 1970s, Professors Jin and Yu jointly created the Reaction Engineering Program in the Department of Chemical Engineering at Tsinghua University, which later became one of the largest fluidization research groups in the world, known as FLOTU - Fluidization Laboratory of Tsinghua University.     

Remarks on the Behavior of Simple Directionally Reinforced Incompressible Nonlinearly Elastic Solids

The effect of directional reinforcing in generating qualitative changes in the mechanical response of a base neo-Hookean material is examined in the context of homogenous deformation. Single axis reinforcing giving transverse isotropy is the major focus, in which case a standard reinforcing model is characterized by a single constitutive reinforcing parameter. Various qualitative changes in the mechanical response ensue as the reinforcing parameter increases from the zero-value associated with neo-Hookean response. These include (in order): the existence of a limiting contractive stretch for transverse-axis tensile load; loss of monotonicity in off-axis simple shear; loss of monotonicity in on-axis compression; loss of positivity in the stress-shear product in off-axis simple shear; and loss of monotonicity for plane strain in on-axis compression. The qualitative changes in the simple shear response are associated with stretch relaxation in the reinforcing direction due to finite rotation. This revised version was published online in August 2006 with corrections to the Cover Date.     

岩体中非填实爆炸空腔壁振动状态分析

采用流体动力学模型研究了地下空腔中化学爆炸冲击波的传播过程及空腔壁的运动状态。计算中体现了空气冲击波与空腔壁作用后激发的强谱振幅高频冲击波。在实验中 ,解决了空腔内传感器的防护和抗干扰等技术难题 ,测到了空腔壁的地运动加速度波形。通过对所测波形的时频域分析得出了非填实爆炸在源区和近区激发高频应力波 ,其频率明显高于填实爆炸的频率。这些特征与数值计算相一致。最后简略讨论了数值计算与实验测量中需解决的问题。     

Ultrasonic measurement of the bending of a bolt in a shear joint

An ultrasonic pulse/echo technique is used to measure preload in bolts used in structural joints. In this paper, the same instrument is used in a different way to measure change in the ultrasonic measurements due to bending in the bolts. A theory that explains the ultrasonic measurements is developed. The bending loads result in a rotation and a translation of the ultrasonic pulse reflecting face. It also creates a stress gradient in the bolt. This results in a phase variation (or gradient) in the received ultrasonic beam across the face of the transducer. It also results in a physical shift in the received beam relative to the ultrasonic transducer. The phase gradient and the shift in the beam results in change in the pulse travel time. A number of experiments were performed on the bolt to study the effect of the bending on the ultrasonic measurements. The experiments and the theory validate a sensitive new method for measuring the bending loads in the bolts.     

Application of ultrasonic-pulse-spectroscopy measurements to experimental stress analysis

We apply the technique of ultrasonic pulse spectroscopy to measure the interference effects between two shear waves propagating in specimens loaded in uniaxial compression. We show that the power spectrum of an echo containing both fast and slow components of a shear wave will exhibit periodic minima. The periodicity exhibited in the spectrum is 1/Δτ, where Δτ is the difference in arrival time between the fast and slow waves. A change in the state of stress which produces a change in the two shear velocities results in a stress-dependent change in wave-arrival times. Because of this velocity change, the frequency at which a particular minimum occurs in the spectrum changes, and this can be used to indicate the state of stress in the material. Our results indicate that, if the spectrum minima frequencies could be resolved to within 10 kHz, the principal-stress differences within 36 psi (0.251 MPa) could be measured in specimens of aluminum 1 in. (2.54 cm) thick. Inherent in analyzing and measuring echo-interference effects is a single-echo requirement. Thus, transducer coupling effects are minimized and measurements in highly attenuating materials or at high frequencies in normal attenuating materials are possible. This technique shows considerable promise as a means of measuring and monitoring the applied stresses in materials.     

Mathematical simulation of hydrodynamic generators of oscillations

Unsteady turbulent swirled water flow in a channel in the presence of cavitation is calculated. It is shown that in the near-axial channel zone a fluctuating vapor region, or cavity, arises and variations in the cavity shape and dimensions lead to the onset of undamped pressure fluctuations. The amplitude-frequency characteristics of the oscillations are obtained in different channel cross-sections. The amplitude maximum position in the channel expansion zone is in agreement with the available experimental data. The dynamics of toroidal vortices formed in the hydrodynamic generator channel and in the expansion zone at its exit are established.     

关于渗流中流线不封闭的特性和条件

本文对于流体在多孔介质中流动的特性进行理论研究和数值计算，提出两个关于渗流中流线不封闭的特性和条件，得到了在一般工程实际情况中的多孔介质区域内部不存在封闭流线的结论。本文以突变截面圆管中不可压缩渗流为算例，利用半人工瞬变方法进行数值计算，得到流体在充满多孔介质的突扩截面圆管和突缩截面圆管中流动时关于速度分布和压力分布的结果。由此表明，在突变截面附近的渗流区域中不存在回流和分离流，也不存在封闭的流线。渗流的这些流动特性不同于在无多孔介质的空间区域中的流动特性。     

双柱单锥型液-液旋流管内流场的激光诊断

应用激光测速仪，对一种双柱单锥型液 液旋流管内的流动结构，进行了全场范围内的多工况流动诊断研究．揭示出其切向速度由内旋流区和外旋流区构成，其中内旋流区中的速度分布符合准强制涡关系，外旋流区中的速度分布符合准自由涡关系；轴向速度由上行流动区和下行流动区构成，两者之间在直管段以零速点作分界，在锥体段则以零速区作过渡并伴随有一定的回流出现，且该过渡区或回流区的大小随锥体截面的收缩而减小，直到进入直管段后消失；各湍流量的分布以管芯处最大向外逐渐减小，沿轴向是直管段中的湍流度大于锥体段中的湍流度，而且湍流度在旋流管内具有各向异性的特性．     

Effects of external electric field on pool boiling: Comparison of terrestrial and microgravity data in the ARIEL experiment

Pool boiling in microgravity, in the presence of an electric field or less, was investigated in ARIEL test setup, integrated in Fluidpac facility, on Foton-M2 orbital mission. The nucleate boiling curve with FC-72 was measured in terrestrial and reduced gravity conditions, on a heated surface whose size was relevant from a technical point of view, for various degrees of fluid subcooling and high heat rates. An external electrostatic field was also added to investigate its use as a possible replacement of buoyancy. Counterpart tests were carried out in the same apparatus in normal gravity, before the mission. The present paper deals in particular with the comparison between boiling performance in normal and reduced gravity in the entire experimental range.     

氡射气测量在西安地裂缝勘察中的应用研究

为了避免大量开挖揭露工作量, 加快地裂缝的勘察速度, 研究出一种简便易行的探测方法是目前西安地裂缝勘察中迫切需要解决的问题。本文研究了氡射气测量在西安地裂缝勘察应用的地质基础, 结合近十几年工程勘察实践, 讨论了氡射气异常的特征, 分析了氡射气的探测效果, 结果认为：氡射气测量在西安地裂缝探测中的有效率为：８０％左右。     

Heat exchange between a gas bubble and a liquid

The nonlinear problem of thermal and dynamic interaction between a single gas bubble and surrounding liquid is considered. This problem is met in studies of gas-liquid mixture flows, in particular, in Shockwave propagation in such media. A numerical solution is presented for various modes of bubble surface radial motion. The modes correspond to bubble behavior directly beyond a shock-wave front, where the latter enters the bubble screen, and to the behavior of a bubble located in the depths of the bubble curtain, where the wave becomes diffuse. Analytic solutions of the linearized problem of thermal conductivity for free and constrained small harmonic oscillations of a gas bubble in a liquid were obtained in [1, 2]. Cooling of a hot gas bubble was considered in [3], that study, however, contains inaccuracies. In particular, it was assumed in the solution that the gas density in the bubble was homogeneous. The equation for heat flux in dimensionless variables was written inaccurately. However, in the examples considered in [3] these inaccuracies do not lead to significant errors in the numerical results.     

西部缺水地区多样化水资源开发模式探讨

最近我国政府提出了西部大开发的战略决策。发展西部地区首要任务是研究解决水资源缺乏问题。40多年来南京大学在地下水探寻和开发、水资源评价和水污染的模拟等方面取得了系统研究成果。特别是运用新构造理论和优势面理论 ,在地下水资源探寻的研究中取得显著成效 ,近几年来作者提出的缺水山区水资源多样化开发模式研究课题 ,在河北顺平严重缺水区取得初步突破。这对于解决西部的水资源匮乏问题 ,促进西部大开发会具有重要的实际意义。     

The effect of cross-flow velocity on mean-square derivatives measured using hot wires

 It is well known that significant errors occur in the velocity derivative moments measured in turbulent flows when the measuring transducer is too large or Taylor's hypothesis is used in high-turbulence-intensity flows. An additional error occurs when velocity derivative moments are measured with hot wires in high-turbulence-intensity flows, because the wires cannot resolve the individual velocity components in these flows. Estimates of the error this causes in the derivative moments measured with single-, cross-, and parallel-wire probes are developed herein. The errors are significant in the derivative moments measured with cross-wire probes, but are smaller in derivative moments measured with single- and parallel-wire probes. For example, the relative errors in measured in the far field of the round jet are 30–50% smaller than predicted in previous analyses. Received: 10 March 1995/Accepted: 07 December 1999     

Drag reduction and heat transfer in surfactant solutions with excess counterion

We present the results of a study of turbulent drag reduction in a small circulating loop using surfactant solutions with excess counterion. In addition, these solutions were used in measurements of heat transfer, both in pipe flow and in an impinging jet. Both frictional drag and heat transfer were reduced in the pipe flow experiments. Measurements of heat transfer in the impinging jet revealed a dependence on the molar concentration ratio of the counterion. When the counterion was added at a molar concentration 30 times higher than that of the surfactant, the resulting surfactant solution did not reduce the rate of heat transfer in the impinging jet. By using this surfactant system in an impinging jet, we show both a reduction in pipe friction and normal heat transfer potential in a circulating heat exchange system. In order to investigate this difference in heat transfer between pipe flows and impinging jet flows, a comparison was made of the wall shear stress between these two flow regimes. The estimated wall shear stress was of the same order in both flows, and thus was not considered to be the primary cause of the difference in heat transfer. It is instead suggested that the micellar structure of the surfactant is influenced by a compressive deformation of the impinging flow in a manner that is different from the shear deformation observed in pipe flow.     

Comparison of viscous and elastic properties of polyolefin melts in shear and elongation

Viscous and elastic properties of a linear polypropylene (PP) and a long-chain branched low-density polyethylene (LDPE) have been investigated by creep and creep–recovery experiments in shear and elongation. The data obtained verify the ratios between the linear values of the viscosities and the steady-state elastic compliances in shear and elongation predicted by the theory of linear viscoelasticity. In the nonlinear range, no simple correlation between the viscous behaviour in shear and elongation exists. The elongational viscosity of the PP decreases with increasing stress analogously to the shear thinning observed; the linear range extends to higher stresses in elongation than in shear, however. The LDPE shows thinning in shear and strain hardening in elongational flow. For the LDPE, a linear steady-state elastic tensile compliance corresponding to one third of the linear steady-state elastic compliance in shear was determined. For the PP, this theoretically predicted value is approximately reached. Analogous to the viscous behaviour, the linear range extends to higher stresses in elongation than in shear. For both materials, the steady-state elastic compliances in the nonlinear range decrease with increasing stress in shear as well as in elongation. However, the decrease in elongation is more pronounced.     

Comparison of aerosol characteristics during haze periods over two urban agglomerations in China using CALIPSO observations

Using CALIPSO (cloud-aerosol lidar and infrared pathfinder satellite observation) vertical observation data during haze periods from January 2007 to December 2008, we analyzed differences in aerosol characteristics near the surface, as well as in the middle troposphere between the Beijing–Tianjin–Hebei metropolitan region (Area A) and the Yangtze River Delta region (Area B) in China. One significant difference was that haze pollution in Area A was related to local and non-local aerosols, while in Area B it was related to local anthropogenic sources. In all seasons apart from autumn, aerosol pollution in Area A was more severe than in Area B, both near the surface and at higher altitudes. In Area A, non-spherical aerosols were dominant from 0 to 4 km in spring, summer, and winter; while in autumn, there were considerably high numbers of non-spherical aerosols below 0.5 km, and near-spherical aerosols from 0.5 to 4 km. In Area B, both near-spherical and non-spherical aerosols were common in all seasons. Moreover, aerosols with attenuated color ratios of 0–0.2 were more common in all seasons in Area A than in Area B, indicating that fine particle pollution in Area A was more serious than in Area B. Finally, relatively large aerosols linked to gravity settling appeared more frequently near the surface in Area A than in Area B.