小口径轴对称收缩喷嘴射流冲击大平板噪声特性的实验研究

为研究小口径喷嘴冲击射流的噪声特性，测定了3mm口径的轴对称收缩喷嘴在各种压比情况下产生的亚音速和超音速射流冲击坚固大平板产生的噪声。发现噪声在空间呈近似四瓣分布，当喷嘴与平板距离减小时，噪声指向壁射流下游的瓣到增强，反之，噪声指向喷嘴上游的瓣得到增强。噪声随喷嘴距平板距离的增加呈增强的趋势，在距平板一定距离内有锯齿现象。噪声随喷嘴压比的增加而增强，相应于各种工况，存在一不同的压比值，此压比之前，噪声随压比的增大而迅速提高，但有起伏现象，在此压比之后，噪声平缓地随压比的增大而增强。     

水下爆炸中气泡射流壁压特性实验研究

水下爆炸气泡射流载荷是中近场水下爆炸壁压载荷的重要组成部分, 将水下爆炸气泡射流简化为一段高速水柱来研究水下爆炸气泡射流载荷特性是研究水下爆炸气泡射流载荷的主要手段。本文基于腔内爆炸提出了一种新的高速水射流实验方法，并给出了实验装置设计、实验方法以及实验系统。基于实验系统，开展了不同工况下高速水射流的实验研究，研究了腔口位置、腔深对水射流形态的影响，并对水射流的形态形成因素进行了分析。使用压电型壁压传感器测得了水射流冲击壁压，给出了水射流冲击壁压的特性及其特点。实验结果表明:腔口位置与腔深是影响水射流端面形态的重要因素；生成的高速水射流冲击壁压峰值满足水锤理论。基于腔内爆炸的高速水射流实验方法能够应用于包括水下爆炸气泡射流在内的高速水射流形态、壁压特性的研究。     

超音速冲击射流离散频率噪声的屏蔽抑制方法

根据导致超音速冲击射流离散频率噪声的反馈机理，提出了一种能够有效地破坏反馈环的形成，从而抑制超音速冲击射流离散频率噪声的喷嘴屏蔽方法。这种方法是通过阻隔反馈波使其不能到达喷嘴唇口从而破坏反馈环、同时屏蔽罩不与射流接触来实现降噪的目的的。本文介绍了这种方法的基本思想并提出了屏蔽罩的设计要点。实验结果表明，对于合适的屏蔽罩的参数，降噪效果达5分贝以上。应用LDV方法对超声速射流轴线速度进行了测量和比较，发现应用屏蔽降噪方法以后射流轴线速度显著增加，核心区长度增加50%左右。分析表明这种降噪方法对射流冲击障碍物的推力和除尘除水效率的提高有帮助。     

气枪喷嘴高速射流的除水效率研究

为揭示喷嘴除水的机理并进而对气枪喷嘴进行改进和优化设计,本文提出了利用图像分析处理对小尺度气枪喷嘴高速冲击乘风破浪的除水效率的研究方法。该方法将有效除水面积作为衡量喷嘴除水效率的标准,从面实现了对喷嘴整体除水效率的定量测量,并利用该方法对影响气枪喷嘴除水效率的各种因素（一次侧压力,喷嘴到平板的距离和射流攻角）进行了研究,并将实验结果与用热线风速仪及总压探头测量的结果进行了比较,得到冲击射流在平板水平速度分量是蚊蝇 嘴除尘除水效率的决定性因素等结论。     

全入射角度下平板冲击波的壁压载荷及局部空化特性

以平面波理论为基础,推导了无限平板在全入射角度下的冲击波壁压载荷计算公式,利用实验数据对壁压公式进行修正,提出了一种适用于计算有限尺度平板壁压的经验公式;分析了不同入射角度下壁压载荷的变化特性,初步研究了壁压载荷负压特性对平板局部空化的影响。结果表明:修正后的壁压曲线与实际壁压曲线吻合较好;入射角度的增大会加快壁压衰减过程,并使最低壁压的绝对值减小;随着药量或平板厚度的增加,壁压最低负压的绝对值增大,形成局部空化的能力增强;局部空化仅在一定条件范围内才会形成,空化范围受局部空化形成压力及冲击强度等因素的影响较大。     

燃气射流冲击传热特性的数值模拟

针对射流传热问题,利用基于RNGk-ε湍流模型的数值方法模拟了射流垂直冲击平板的流动过程,并与实验数据比较,验证了模型的可行性。在此基础上,以火箭喷管入口参数为入口条件,建立了超音速燃气射流垂直冲击平板和冲击浸没平板的计算模型,分析了不同冲击条件下努塞尔数分布规律和温度分布规律, 论述了超音速射流传热的特性及影响传热特性的因素。得到了冲击距离为(14~18)D的努塞尔数取值范围,并表明冲击距离和射流温度是影响传热效率的关键因素;冲击距离增加,传热效率降低,冲击平板表面的射流温度越高,传热效率越高。     

不定原点喷嘴射流中流体物理的实验研究

为了能够更好地了解不定源喷嘴（indeterminate origin nozzle）射流中的物理过程，本文应用平面激光诱导荧光技术对一个大尺度的水射流进行了实验研究。流场显示的实验结果表明不定源喷嘴在射流的剪切层引入了蘑菇形反向旋转的涡对。这些涡的矢量方向与射流方向相同或相反，被称为流向涡（streamwise vortex）。由于射流中存在开尔文一亥姆霍兹不稳定，每当一个横向涡（spanwisevortex，即涡的矢量方向与射流方向垂直）从喷嘴脱流时会产生瞬时的低压，该瞬时低压促使向内发展的流向涡对在喷嘴的凹槽处生成。这些涡对在向下游流动的过程中会重组并在喷嘴的尖峰面生成向外发展的涡对。这些流向涡极大地影响了射流的发展。流向涡与横向涡的相互作用促使射流更早地发展成为湍流。由于流向涡同时也在射流中引入了径向的剪切流动，因此导致了更多的湍流生成从而增强了射流与周围流体的混合。     

液腔体中气体射流冲击压力的实验测量

对充液腔体中气体射流的冲击效应进行了实验研究. 测量结果表明了冲击压力的瞬态最 大值、稳态平均值和脉动值随喷管进口压比的增加而增加，冲击区是主要的噪声源和动态压 力承载部位. 通过充气与充水两种状态的对比实验，还揭示了腔体充水时气体射流冲击压力 出现一个上冲阶段，其瞬态最大值比充气值有显著的增加.     

半封闭狭缝湍流冲击射流的数值模拟

将Yakhot和Orszag提出的RNGk-ε模型推广应用于半封闭狭缝冲击射流场的数值模拟，以评价该模型对这种复杂湍流的预测能力。将计算得到的流场平均速度分布、湍流强度分布和流函数分布与标准k—ε模型的预测结果以及相应的实验数据进行了比较，结果表明：RNGk—ε模型的预测结果总体上要好于标准k—ε模型，但与实验值相比，所有预测结果都还存在不同程度的误差，尤其是近壁区和滞止点较远下游处的湍流强度分布。说明RNG模型虽然已在某些湍流的预测中取得了一定的成功，但要定量准确地预测冲击射流场，还必须针对其流动特征对模型加以改进。     

轴对称直喷管的射流噪声特性实验研究

为了研究喷管射流噪声特性问题,应用丹麦B.K.公司3560C型多用途分析系统,对抽对称直喷管在不同压比下产生的亚音速和跨音速射流噪声进行了测量.并对外流场轴向和截面流动特性进行了测量和分析,确定了测量噪声探头放置位置,比较了离模型截面不同位置处的噪声.给出频率在5000HZ内噪声变化的规律,发现在低频时随着静压比的增加...     

An experimental investigation on flow structures of confined and unconfined impinging air jets

The flow characteristics of both confined and unconfined air jets, impinging normally onto a flat plate have been experimentally investigated. The mean and turbulence velocities, and surface pressures were measured for Reynolds numbers ranging from 30,000 to 50,000 and the nozzle-to-plate spacings in range of 0.2–6. Smoke-wire technique is used to visualize the flow behavior. The effects of Reynolds number, nozzle-to-plate spacing and flow confinement on the flow structure are reported. In the case of confined jet, subatmospheric regions occur on both impingement and confinement surfaces at nozzle-to-plate spacings up to 2 for all Reynolds numbers in consideration and they lie up to nearly the same radial location at both surfaces. However, there is no evidence of the subatmospheric region in unconfined jet. It is concluded that there exists a linkage among the subatmospheric region, turbulence intensity and the peaks in heat transfer coefficients for low spacings in impinging jets.     

Numerical simulation of an impinging jet on a flat plate

Two-dimensional normal impinging jet flowfields, with or without an upper plate, were analysed by employing an implicit bidiagonal numerical method developed by Lavante and Thompkins Jr. The Jones–Launder K–? two-equation turbulent model was employed to study the turbulent effects of the impinging jet flowfield. The upper plate surface pressure, the ground plane pressure and other physical parameters of the momentum flowfield were calculated at various jet exit height and jet inlet Reynolds numbers. These results were compared with those of Beam and Warming's numerical method, Hsiao and Chuang, and others, along with experimental data. The potential core length of the impinging jet without an upper plate is longer than that of the free jet because of the effects of the ground plane, while the potential core length of the impinging jet with an upper plate is shorter than that of the free jet because of the effects of the upper plate. This phenomenon in the present analysis provides a fundamental numerical study of an impinging jet and a basis for further analysis of impinging jet flowfields on a variable angle plate.     

Relationship between vortex and sound in under‐expanded supersonic impinging jets

The study of an under‐expanded supersonic jet impinging on a flat plate by using large‐eddy simulation is reported. A third‐order upwind compact difference and a fourth‐order symmetric compact scheme are employed to discretize the nondimensional axisymmetric compressible Favre‐filtered Navier–Stokes equations in space, whereas the third‐order Runge–Kutta method with the total variation diminishing property is adopted to deal with the temporal discretization. The numerical simulation successfully captures the shock wave and vortex structures with different scales in the flow field. Waves with high and low frequencies traveling forward and reflecting back, and sound sources in different locations can be observed. By comparison with the frequency of the impinging tone from the experiment, it can be deduced that the change of pressure and swirling strength in the shear layer, pressure change on the impinging plate, and vortex merging in the jet shear layer are interdependent with the impinging tone. The effects of nozzle lip thickness on the impinging jet flow field have been investigated. The results show that the values of pressure fluctuation and vortex swirling strength in the shear layer near the nozzle have an extremum with the variation of the nozzle lip thickness. The results provide a theoretical foundation for the design of supersonic nozzles. Copyright © 2011 John Wiley & Sons, Ltd.     

冲击高度对自由冲击射流影响的实验研究

采用热线风速仪测量了雷诺数为 ２３ ０００时四种冲击高度下率流自由冲击射流流场，并给出详细的结果．表明壁面的“阻尼”影响主要集中在近壁面０．５Ｄ以内．小冲击高度时径向速度下降得比大冲击高度时明显要快，量值也较小；在ｒ／Ｄ≤１．５处，小冲击高度时紊动能的数值大小和分布趋势与大冲击高度时不同，特别是在喷管出口距冲击板高度Ｚ与喷管直径Ｄ之比Ｚ／Ｄ为８时分布特殊，在其它测点处，紊动能的分布趋势基本一致，只是大冲击高度下的值较大；流动结构在Ｚ／Ｄ为６～８时发生了较大的变化，这种变化与势流核心区有关，在势流核心区的顶端以及下游的一段距离内紊流度都很高．     

Computations for a jet impinging obliquely on a flat surface

A SIMPLE-C algorithm and Jones-Launder k-ε two-equation turbulence model are used to simulate a two-dimensional jet impinging obliquely on a flat surface. Both the continuity and momentum equations for the unsteady state are cast into suitable finite difference equations. The pressure, velocity, turbulent kinetic energy and turbulent energy dissipation rate distributions are solved and show good agreement with various experimental data. The calculations show that the flow field structure of the jet impinging obliquely on a flat surface is strongly affected by the oblique impingement angle. The maximum pressure zone of the obliquely impinging jet flow field moves towards the left as the oblique impingement angle is decreased.     

Oscillatory behavior of supersonic impinging jet flows

Oscillatory flows of a choked underexpanded supersonic impinging jet issuing from a convergent nozzle have been computed using the axisymmetric unsteady Navier--Stokes system. This paper focuses on the oscillatory flow features associated with the variation of the nozzle-to-plate distance and nozzle pressure ratio. Frequencies of the surface pressure oscillation and flow structural changes from computational results have been analyzed. Staging behavior of the oscillation frequency has been observed for both cases of nozzle-to-plate distance variation and pressure ratio variation. However, the staging behavior for each case exhibits different features. These two distinct staging behaviors of the oscillation frequency are found to correlate well if the frequency and the distance are normalized by the length of the shock cell. It is further found that the staging behavior is strongly correlated with the change of the pressure wave pattern in the jet shear layer, but not with the shock cell structure. Communicated by K. Takayama PACS 02.60.Cb; 47.40.−x; 47.40.Nm; 47.35.+I; 47.15.−x     

The planar jet-plate oscillator

The aeroacoustic noise generated by a high speed, planar gas jet impinging on a flat plate is investigated experimentally. The jet used in this study is typical of those commonly found in industrial applications such as in various coating control and heat transfer processes. Normal jet impingement on the plate is found to generate strong acoustic tones over a wide range of impingement distances and jet velocities. The characteristics of these tones, as a function of the jet velocity and impingement distance, are quantified. Phase and amplitude measurements of the pressure fluctuations on the impingement plate indicate that the acoustic tones are generated by an antisymmetric instability mode of the jet oscillation. The effect of plate inclination in both the transverse and span-wise directions, with respect to the incident jet, is also studied. The jet-plate tone is found to be much more sensitive to changes in the span-wise plate inclination than to changes in the transverse inclination, but in both cases, a complete suppression of the tone is found to be possible.     

Flow structure and heat transfer characteristics of an unconfined impinging air jet at high jet Reynolds numbers

The flow and heat transfer characteristics of an unconfined air jet that is impinged normally onto a heated flat plate have been experimentally investigated for high Reynolds numbers ranging from 30,000 to 70,000 and a nozzle-to-plate spacing range of 1–10. The mean and turbulence velocities by using hot-wire anemometry and impingement surface pressures with pressure transducer are measured. Surface temperature measurements are made by means of an infrared thermal imaging technique. The effects of Reynolds number and nozzle-to-plate spacing on the flow structure and heat transfer characteristics are described and compared with similar experiments. It was seen that the locations of the second peaks in Nusselt number distributions slightly vary with Reynolds number and nozzle-to-plate spacing. The peaks in distributions of Nusselt numbers and radial turbulence intensity are compatible for spacings up to 3. The stagnation Nusselt number was correlated for the jet Reynolds number and the nozzle-to-plate spacing as Nu _st∝Re ^0.69(H/D)^0.019.     

Three-dimensional vortex dynamics and convective heat transfer in circular and chevron impinging jets

This paper describes an experimental investigation at Reynolds number equal to 5000 on circular and chevron impinging jets by means of time-resolved tomographic particle image velocimetry (TR-TOMO PIV) and infrared (IR) thermography. TR-TOMO PIV experiments are performed at kilo-hertz repetition rate in a tailored water jet facility where a plate is placed at a distance of 4 diameters from the nozzle exit. Using air as working fluid, time-averaged convective heat transfer is measured on the impinged plate by means of IR thermography with the heated-thin-foil heat transfer sensor for nozzle-to-plate distances ranging from 2 to 10 diameters. The circular impingement shows the shedding and pairing of axisymmetric toroidal vortices with the later growth of azimuthal instabilities and counter-rotating streamwise vortices. In the chevron case, instead, the azimuthal coherence is replaced by counter-rotating pairs of streamwise vortices that develop from the chevron notches. The heat transfer performances of the chevron impingement are compared with those of the circular one, analyzing the influence of the nozzle-to-plate distance on the distribution of Nusselt number. The chevron configuration leads to enhanced heat transfer performances for all the nozzle-to-plate distances hereby investigated with improvements up to 44% at the center of the impinged area for nozzle-to-plate distance of 4. Such enhancements are discussed in relation to the streamwise structures that, compared with the toroidal vortices, are associated with an earlier penetration of turbulence towards the jet axis and a higher arrival speed.