饱和砂土的循环边界面本构模型

饱和砂土在循环加卸载过程中,土体发生显著的组构变化和塑性变形的累积.试验现象分析表明,循环过程中,砂土的首次与再循环塑性模量既有区别又有联系.因此,论文引入考虑组构变化的剪胀内变量,并提出循环塑性模量的关系式,真实描述上述两种现象;进而基于已有本构模型的基础,建立饱和砂土的循环边界面本构模型.最后,将饱和砂土的模型预测结果与三轴试验结果进行验证对比,得到较好地吻合,这表明该模型能够合理反映饱和砂土循环加卸载的变形行为.     

剪胀性砂土边界面模型的研究

剪胀性对于砂土,尤其是中密以及密实砂土,是一个非常显著的特性。相变线是剪胀性砂土的特征曲线,能够反映砂土的围压以及初时孔隙比对变形特性的影响。本文在边界面塑性理论的框架内,把相变状态参量引入到剪胀方程以及塑性硬化模量中,建立了一个能够描述砂土剪胀性以及循环特性的本构模型。本模型采用一套参量可以模拟不同初时孔隙比、不同围压、排水(或不排水)条件下单调(或循环)加载的应力-应变特性。验证表明本模型数值计算与试验结果相吻合。     

砂土的应力路径本构模型

将微元应力路径线性逼近,转变成与其充分接近且易于计算应变的等平均应力微元和等应力比微元,计算任意加荷应力路径所产生的塑性应变,建立了双屈服面的砂土应力路径本构模型．模型体现了岩土塑性理论分量屈服和非关联流动法则的要求,在p,q平面内根据双线性的屈服线确定了加卸载准则．结合广义非线性强度理论采用变换应力三维化方法简单、合理地使模型实现三维化．通过试验数据的验证表明,砂土应力路径本构模型可以合理地描述各种应力路径下砂土的变形和强度特性。     

基于SMP破坏准则的饱和砂土弹塑性本构模型

利用土体的塑性流动理论，提出了用于描述饱和砂土在单调荷载作用下的应力一应变反应性质的弹塑性本构模型。土体总的变形由三部分组成：即弹性应变、与体积屈服机制相关的塑性应变和与剪切屈服机制相关的塑性应变，其中与剪切屈服机制相关的塑性应变的得出是基于SMP破坏准则。通过将模型预测的结果与试验结果进行对比，表明该模型能够较为准确地描述饱和砂土在单调加载条件下的反应性质。     

基于塑性体积应变的岩石损伤变形特性实验研究

为分析岩石塑性变形与损伤的关系,在定义岩石的初始损伤和临界损伤,提出塑性体积应变分析方法,从而以塑性体积应变为损伤变量,采用归一化方法建立岩石的损伤本构模型。采用递增循环加载实验确定岩石损伤本构模型中的弹性卸载模量和弹性应变比例系数两个参数。通过实验和理论分析得出:当荷载较小时,普通单轴压缩状态下岩石损伤随荷载的增加具有减小趋势,荷载超过一定数值后,岩石损伤才开始增加;单轴递增循环压缩状态下当循环荷载大于约35%峰值强度后,卸载后岩石的损伤具有增加的趋势,小于该荷载之前具有减小的趋势。整个加载过程的理论应力-应变曲线能很好地与实验结果相吻合,在循环加载区间理论结果还能体现出岩石实验结果中的回滞环。     

2D-C/SiC复合材料的单轴拉伸力学行为及其强度

通过单调拉伸和循环加卸载试验, 研究了平纹编织C/SiC复合材料的损伤演化过程及其应力-应变行为. 结果表明, 残余应变、卸载模量和外加应力的关系曲线与拉伸应力-应变曲线具有类似的形状. 基于剪滞理论和混合率建立了材料的损伤本构关系和强度模型, 分析计算表明, 残余应变主要由裂纹张开位移和裂纹间距决定, 而卸载模量主要由界面脱粘率决定; 材料的单轴拉伸行为主要由纵向纤维束决定, 横向纤维对材料的整体模量和强度贡献较小. 理论模拟结果与试验值吻合较好.      

主应力轴旋转下黏土累积变形的分数阶元件模型

在长期交通载荷作用下土体塑性累积变形本构模型对路基沉降计算至为关键.元件组合模型可以计算岩土体循环累积应变,但现有的各类元件模型未能反映饱和软黏土的主应力轴循环旋转现象.在对饱和软黏土进行等向固结条件下的主应力轴循环旋转加载试验及非等向固结下的循环扭剪试验基础上,将Abel黏壶代替Burgers模型中的Newton黏壶,得到分数阶Burgers模型;利用遗传算法优化循环塑性累积应变的Burgers模型和分数阶Burgers模型的参数,通过对比两组模型的计算值与试验值,发现分数阶模型更适合模拟计算循环载荷下饱和软黏土的累积变形.     

砖砌体双参数单轴受压弹塑性损伤力学模型

参考弹塑性损伤模型理论和相关试验数据,建立了砖砌体单轴单调受压和重复受压两种弹塑性损伤本构模型.在模型中采用抗压强度和峰值压应变双参数来调整形变曲线,从而实现了砖砌体单轴受压本构模型的精细化建立.模型不但与既有弹塑性模型相符,而且还符合受压延性与强度呈反向变化的试验结论.重复受压加-卸载路径建立在卸载线性假定的基础上,参考两组试验数据,得出了双线性抗压刚度劣化函数,并通过强度线性插值来调整劣化速率,从而建立了随强度改变的受压加-卸载损伤本构模型.     

剪胀性饱和砂土弹塑性模型

在修正剑桥模型基础上,本文建立的剪胀性饱和砂土弹塑性模型使用相变状态参数描述剪胀性饱和砂土剪胀特性,克服了修正剑桥模型不能直接模拟剪胀砂土力学行为这一局限性。该模型有两方面的改进:一方面,模型将剪胀应力比Md引入剪胀方程;另一方面,模型在塑性功基础上提出用与应力路径无关的硬化参数来替代修正剑桥模型中的塑性体积应变增量。通过试验验证及与修正剑桥模型计算结果对比,结果表明,该模型较适合模拟剪胀性饱和砂土的力学性能,同时也能较好地体现较密实砂土的硬化及软化现象。模型共8个参数,用常规三轴试验就可获取。     

非比例循环载荷下塑性模量的讨论

对1Cr18Ni9Ti不锈钢进行菱形应变路径的非比例循环本构实验,根据实验结果及分析,对双面本构模型给出了一个极限面定义,以保证屈服面不与极限面相交,在这个极限面定义及实验结果的基础上,对不同本构模型所定义的距离与塑性模量的相关性进行了讨论,表明Mroz和Chen的距离与塑性模量具有较好的相关性。     

Micromechanical modeling of the elasto-viscoplastic behavior of semi-crystalline polymers

A micromechanically based constitutive model for the elasto-viscoplastic deformation and texture evolution of semi-crystalline polymers is developed. The model idealizes the microstructure to consist of an aggregate of two-phase layered composite inclusions. A new framework for the composite inclusion model is formulated to facilitate the use of finite deformation elasto-viscoplastic constitutive models for each constituent phase. The crystalline lamellae are modeled as anisotropic elastic with plastic flow occurring via crystallographic slip. The amorphous phase is modeled as isotropic elastic with plastic flow being a rate-dependent process with strain hardening resulting from molecular orientation. The volume-averaged deformation and stress within the inclusions are related to the macroscopic fields by a hybrid interaction model. The uniaxial compression of initially isotropic high density polyethylene (HDPE) is taken as a case study. The ability of the model to capture the elasto-plastic stress-strain behavior of HDPE during monotonic and cyclic loading, the evolution of anisotropy, and the effect of crystallinity on initial modulus, yield stress, post-yield behavior and unloading-reloading cycles are presented.     

Modeling liquefaction of water saturated granular material under undrained cyclic shearing

The tendency of particles in a water-saturated granular mass to re-arrange into a denser state during cyclic shearing under pressure results in an increase in pore water pressure. The increase in the pore water pressure causes a reduction in the inner particle contact forces, and in turn easier re-arrangement of the particles. Eventually, the material loses its shear strength, partially or almost completely. In this paper, a general three-dimensional continuum mechanics model is presented for the deformation of granular materials. A physically based model is also presented for characterization of liquefaction of the water saturated granular material under undrained cyclic shearing. The model incorporates the fabric of the granular mass, which develops as the frictional granular mass is deformed in shear. It includes the coupling between shearing and excess pore water pressure. The model parameters are estimated, based on the results of cyclic shearing experiments on large hollow cylindrical samples of silica sand. Basically, the calculation results utilizing this model can embody liquefaction phenomena of the water saturated granular material under undrained cyclic shearing.     

Unified modeling of the monotonic and cyclic behaviors of sand and clay

In this study, we aim to investigate a unified modeling method for the monotonic and cyclic behaviors of sand and clay. A simple double-yield-surface model, with plastic hardening modulus and dilatancy relation being dependent on density state unlike in existing approaches,is developed by considering the location of the critical state line. The model is used to simulate the drained and undrained tests of various sands and clays under monotonic and cyclic loadings.Prediction results are compared with experimental results, which show that the proposed approach is capable of modeling the monotonic and cyclic behaviors of sand and clay.     

On the implementation of a multi-surface kinematic hardening plasticity and its applications

This paper is concerned with an application of the multi-surface plasticity in solid mechanics and geotechnical problems. The model is of a von-Mises type with associated flow rule, originally proposed by Montans. The Mroz translation rule is implemented to the movements of the yield surfaces and the fully implicit scheme with radial mapping method is applied in numerical computations. Algorithmic consistent tangent modulus with numerical integration algorithm of constitutive equations is extracted. The model is developed in the class of kinematic hardening models, so the ‘Masing’ rule is preserved. The model is able to consider the plastic strain accumulation in constant axial stress state, such as ratcheting. The implementation is validated by means of a simple deformation path of combined extension and compression test, a pure shear test with pseudo-random loading, a test which demonstrates the capabilities of the model in simulation of cyclic loading and ratcheting, a cyclic shear test in saturated undrained sand and finally, the analysis of a plate with holes, which presents the shear band using the multi-surface plasticity model.     

复杂加载条件下的砂土本构模型

试验表明,饱和砂土的应力应变关系具有显著的密度以及压力依存性,上述两点构成了描述砂土静力加载下变形特性无法忽视的因素. 此外,在循环加载等复杂加载作用下,砂土还会表现出明显的应力诱导各向异性以及相变转换特性. 基于在e--p空间中存在唯一的临界状态线这一基本假定,通过在e--p空间中引入当前状态点与临界状态线的距离R来作为反映密度与压力依存特性的状态参量, 将变相应力比以及峰值应力比表达为状态参量的指数函数,将上述应力比参量引入到统一硬化参量中可准确地反映初始状态下围压、密度 对于单调加载下应力应变关系的影响规律,能描述砂土剪缩、剪胀,应变软化、硬化等特性. 采用非相关联流动法则,p--q空间中采用水滴型屈服面,塑性势面为椭圆面,松砂在单调加载下的静态液化现象也可描述. 为反映循环加载下塑性体积应变的累积特性以及塑形偏应变的滞回特性,在循环加载下将状态参量R表达为应力比参量,并在硬化参数中引入描述应力诱导各向异性特性的旋转硬化部分,所提模型可有效地描述循环加载下剪切模量的衰减特性、刚度衰化性质、强度减小特性,在不排水约束作用下,则会产生往返活动性现象. 通过一系列的模型模拟与试验结果对比,验证了本构模型的有效性及适用性.      

黄河三角洲粉质土的动模量和阻尼比试验研究

结合室内共振柱和动三轴实验,对黄河三角洲饱和原状粉质土体(粉土、粉砂、粉质粘土)动模量和阻尼比的影响因素和发展规律进行了详细的研究。研究表明,在粉粒和粘粒含量对动模量的共同影响中,粉粒含量起着举足起重的作用;侧限压力对归一化剪模比和阻尼比的影响均较显著,相比粘粒含量的影响不大。通过与Seed建议的砂土及饱和粘土的G/Gmax~γ曲线和λ~γ曲线进行对比,结果显示研究区的粉质土相比一般的砂土和饱和粘土而言,其动力变形特性更接近于砂土,但是与砂土也存在着非常明显的差异;其发展规律与其他地区沉积粉质土也较为不同,具有明显的区域性。采用修正了的Hard in-D rnevich模型和对数模型分别对G/Gmax~γ曲线和λ~γ曲线进行拟合,给出了三类粉质土的归一化动力变形G/Gmax~γ/γr关系曲线,对模型中有关参数的影响因素做了初步的探讨。     

An experimental study of inhomogeneous cyclic plastic deformation of 1045 steel under multiaxial cyclic loading

An experimental study was conducted on the inhomogeneous cyclic plastic deformation of 1045 steel under multiaxial cyclic loading. Thin-walled tubular specimens were used and small strain gages were bonded on the specimen surface to characterize the local deformation. The controlled loading paths included cyclic tension–compression, cyclic torsion, proportional axial-torsion, 90°-out-of-phase axial-torsion, and fully reversed torsion with a constant axial stress. The maximum stress in each experiment was lower than the lower yield stress of the material. It was found that the cyclic plastic deformation within the gage section of the specimen under multiaxial stress state followed the three-stage process that was observed from uniaxial loading, namely, incubation, propagation, and saturation. The plastic deformation was significantly inhomogeneous during the propagation stage, and the inhomogeneity continued through the saturation stage. The duration of each stage and the saturated strains were dependent on the cyclic stress amplitude and the loading path. Multiaxial stress state reduced the incubation stage. With identical equivalent stress magnitude, the nonproportional loading path resulted in the shortest incubation and propagation stages, and the saturated equivalent plastic strain magnitude was the smallest. Although the deformation over the gage section was inhomogeneous, the plastic deformation in a given local area was found to be practically isotropic.     

On fatigue crack growth in ductile materials by crack-tip blunting

One of the basic mechanisms for fatigue crack growth in ductile metals is that depending on crack-tip blunting under tensile loads and re-sharpening of the crack-tip during unloading. In a standard numerical analysis accounting for finite strains it is not possible to follow this process during many cycles, as severe mesh distortion at the crack-tip results from the huge geometry changes developing during the cyclic plastic straining. In the present numerical studies, based on an elastic-perfectly plastic material model, crack growth computations are continued up to 200 full cycles by using remeshing at several stages of the plastic deformation. Three different values of the load ratio R=K_min/K_max are considered. It is shown that the crack-tip opening displacement, CTOD, typically undergoes a transient behaviour, with no crack closure during many cycles, before a steady-state cycling with crack closure at the tip starts to gradually develop.