纤维板增强钢筋砼缺口梁承载力试验研究

通过对8组24根碳纤维薄板增强钢筋混凝土梁进行三点弯曲试验，探讨碳纤维薄板增强钢筋混凝土缺口梁的破坏过程、极限承载力及其影响因子．研究结果表明：1)碳纤维薄板增强钢筋混凝土缺口梁总是沿着纤维薄板与混凝土的界面发生剥高破坏；2)与无增强梁相比，增强梁的极限来载力可以提高20％一40％．而且当纤维薄板贴长Lc与两支点间距离S之比为0．57左右时增强效果最明显；3)缺口对梁的破坏模式影响较大，而对梁的极限承载力影响不大(下降10％-15％)．     

循环载荷下碳纤维薄板增强RC梁的疲劳性能试验研究

以碳纤维薄板(CFL)增强RC梁为研究对象,通过对循环载荷作用下增强梁的三点弯曲疲劳试验研究,得到了增强梁的线性对数疲劳寿命曲线和跨中挠度的演化规律,外推得到了极限疲劳强度和抗弯刚度的演化规律,揭示了增强梁的疲劳破坏机理。循环载荷下CFL增强RC梁的破坏模式包括混凝土开裂、碳纤维薄板与混凝土界面剥离、主筋屈服等模式,疲劳破坏过程具有明显的损伤成核、稳定扩展、失稳扩展三阶段发展规律。与普通RC梁相比较,CFL增强RC梁的裂缝分布较均匀、密集,粘贴CFL对增强梁的初始抗弯刚度提高幅度较小,对疲劳损伤阶段的抗弯刚度则提高了约一倍。根据CFL增强RC梁的疲劳寿命曲线得到其极限疲劳强度为25.42 kN,为三点弯曲静载下极限承载力的58.5%。     

碳纤维增强混凝土缺口梁承载力试验研究

利用纤维薄板对混凝土构件进行加固或修补以提高其承载能力及延长使用寿命是一种新的先进补强方法。本文通过改变试件的缺口高度（α0）和纤维薄板长度（LX）,对素混凝土以及碳纤维薄板增强混凝土三点弯曲缺口梁试件进行对比试验研究,探讨两种梁的破坏机理及其极限承载力。试验及分析结果表明,采用碳纤维薄板外贴在梁的底部可提高梁 的整体刚度和强度,抑制混凝土中裂缝的扩展,改变梁的破坏模式,并大大提高其极限承载能力（可提高1．7－6．9倍）。     

随机载荷下碳纤维薄板增强RC梁试验研究

桥梁等钢筋混凝土结构在运营期所受活载为随机载荷。研究随机载荷作用下碳纤维薄板(Carbon Fiber Laminate简称CFL)片材增强钢筋混凝土构件的疲劳性能,对于采用碳纤维薄板技术加固桥梁等混凝土结构有重要的指导意义。本文通过随机载荷作用下碳纤维薄板增强RC梁的三点弯曲疲劳试验,得到了增强梁的S-N曲线和跨中挠度的演化规律,揭示了随机载荷下增强梁的疲劳破坏机理。随机载荷下碳纤维薄板增强RC梁的破坏模式包括钢筋断裂、碳纤维薄板剥离、混凝土压坏等破坏形态,疲劳破坏过程具有明显的损伤成核、稳定扩展、失稳扩展的三阶段发展规律。     

受拉区带缺口钢筋混凝土梁弯曲极限承载力的近似计算

进行受拉区带缺口钢筋混凝土梁和无缺口梁的对比实验，分析带缺口梁的承载机理，提出一种近似计算弯曲极限承载力的方法。     

爆炸荷载作用下影响RC梁破坏形态的主要因素分析

在冲击、爆炸等强荷载作用下，钢筋混凝土结构通常是发生弯曲破坏。室内外试验结果表明，当动荷载峰值较大、作用时间较短（脉冲荷载）时，钢筋混凝土结构易发生脆性的剪切破坏，其主要原因是脉冲荷载的高频成份丰富和加载速率高等特点容易激发结构构件中的剪切变形和剪 应力。本文基于Timoshenko梁理论，提出了一种爆炸荷载作用下钢筋混凝土梁破坏形态的有限差分预报方法，利用该方法分析了荷载加载速率、截面高度、混凝土强度、配筋率等对钢筋混凝土破坏形态的影响规律，并指出，随着荷载升压段加载速率、截面高度、主筋配筋率的增加或混凝土强度的降低，梁的破坏形态从弯曲破坏转变为剪切破坏。     

钢筋混凝土桥墩弯剪数值分析模型

基于修正的压力场理论MCFT(The Modified Compression Field Theory)和纤维单元模型建立了钢筋混凝土桥墩的弯剪数值分析模型,以MCFT理论确定桥墩的剪切力-剪切位移关系,并与考虑桥墩弯曲变形的纤维单元模型组合,共同考虑桥墩的弯-剪-轴力耦合作用.通过与六个弯剪破坏控制的圆形截面钢筋混凝土桥墩拟静力试验结果的对比,对分析模型进行了验证.主要认识结论为基于MCFT理论可准确地计算弯剪破坏桥墩的屈服荷载、极限荷载和弹性阶段剪切刚度,剪切开裂是引起钢筋混凝土构件剪切力-剪切位移关系刚度突变的主要因素,而弯曲开裂与纵筋屈服对刚度的影响较小；分析模型对弯剪破坏桥墩的滞回曲线、弯曲与剪切变形成分均进行了较为准确的模拟分析.     

温度-随机载荷下CFL加固RC梁疲劳性能的实验研究

考虑亚热带地区公路桥梁的服役环境温度与车辆载荷的作用效应,本文以碳纤维薄板(CFL)加固钢筋混凝土(RC)桥梁结构为研究对象,利用本课题组构建的实验平台,提出了温度与车辆随机载荷耦合作用下CFL加固RC梁的疲劳实验方法。在3个温度和3个载荷水平下实施了温度-随机载荷耦合作用下的三点弯曲疲劳实验,初步探讨了温度-随机载荷作用下加固梁的疲劳破坏机理,并提出了温度-随机载荷耦合下加固梁疲劳寿命的半经验公式。     

三维刚体弹簧元法在RC深梁抗剪性能尺寸效应评价中的应用

选取典型的钢筋混凝土(RC)深梁受剪试验，开发并运用三维刚体弹簧元法(3D RBSM)模拟了大尺寸截面深梁的受剪破坏过程，以及箍筋对深梁抗剪性能的影响。结果表明，3D RBSM不仅能够较准确地计算RC深梁的开裂荷载、名义抗剪强度以及箍筋的增强作用，而且能够模拟裂缝的开展以及构件的破坏。相比于有限元法，3D RBSM具有以下优势：大幅度提高了名义抗剪强度的计算精度，实现了散布裂缝模拟的可视化以及混凝土裂缝宽度的直观、定量评价；能够更好地捕捉峰值荷载后的软化行为。因此，3D RBSM为大尺寸截面深梁的受剪破坏模拟、明晰抗剪性能尺寸效应机理和完善大尺寸RC构件设计提供了有效研究手段。     

粘贴碳纤维布加固混凝土管道试验研究

首次通过对14个素混凝土和14个钢筋混凝土环状试件外粘碳纤维布加固性能进行试验，研究了碳纤维布加固混凝土内压圆管的破坏特征、受力性能和破坏机理。对不同加固方法及一次或二次受力的混凝土管在内压力作用下的极限承载力、荷载一应变关系等方面进行了研究。试验结果表明，用碳纤维布加固混凝土内压管可以显著地提高极限承载力，明显的改善了构件的延性，能够获得良好的力学性能。加固后试件的开裂承载力与未加固试件相比，提高幅度不大，加固试件二次受力与一次受力相比，开裂荷载有所降低，但极限承载力基本相同。用碳纤维布加固内压管是一个新课题，具有很好的应用前景，用本文提出的加固方法具有优良的加固性能，可为工程应用提供参考。     

Preface: Current research progress on mechanics of high speed rail

The construction and operation of high-speed rail（HSR）grid within the past two decades in China,in terms of the scale,may be possibly comparable to any national-wide construction in the history of China,even the Great Wall.By counting railways with commercial train service at the speed of200 km/h,China has the world’s longest HSR network with over 19 369.8 km of track in service today and this number     

ACTA MECHANICA SINICA 2014 ANNUAL SUBJECT INDEX

正~~     

人造地震动合成中的位移误差分析

三角函数级数法是合成人工地震动常用算法之一,但是通过对加速度积分求取位移时,却存在与零线漂移相类似的位移漂移现象。     

Hermitian space-time finite elements for estuarine mass transport

Space-time finite element solutions of the convection–dispersion equation using higher-order nodal continuity and Hermitian polynomial shape functions are described. Five separate elements ranging from a complete linear element with C^0,0 nodal continuity to a complete first-order Hermitian element with C^1,1 nodal continuity are subjected to detailed analysis. Wave deformation analyses identify the source of leading or trailing edge oscillations, trailing edge oscillations being the major source of difficulty. These observations are confirmed by numerical experiments which further demonstrate the potential of higher-order nodal continuity. The performance of the complete first-order Hermitian element is quite satisfactory and measurably superior to the linear element.     

Rainwater rivulets on a cable subject to windFilets d'eau de pluie sur un câble soumis au vent

Rainwater rivulets appear on inclined cables of cable-stayed bridges when wind and rain occur simultaneously. In a restricted range of parameters this is known to cause vibrations of high amplitudes on the cable. The mechanism underlying this effect is still under debate but the role of rainwater rivulets is certain. We use a standard lubrication model to analyse the dynamics of a water film on a cylinder under the effect of gravity and wind load. A simple criterion is then proposed for the appearance and position of rivulets, where the Froude number is the control parameter. Experiments with several geometries of cylinder covered with water in a wind tunnel show the evolution of the rivulets with the Froude number. Comparison of the prediction by the model with these experimental data shows that the main mechanism of rivulet formation and positioning is captured. To cite this article: C. Lemaitre et al., C. R. Mecanique 334 (2006).     

Cristallisation par onde acoustique : le cas de l'héliumCrystallization by acoustic waves: the case of helium

We establish a theoretical model to explain the nucleation of a crystal of helium by an acoustic over-pressure. We explain the interfacial laws for this ultra-fast cristallization, close to the sound speed. Assuming spherical symmetry and taking into account the experimental data, we recover the dynamics of the growth and melting during an over-pressure impulse. To cite this article: M. Ben Amar et al., C. R. Mecanique 331 (2003).     

Structure initiale et propriétés de liquéfaction statique d'un sableInitial structure and static liquefaction properties of sand.

Based on the use of two different preparation procedures for reconstituting triaxial samples of sand, i.e. wet tamping and dry pluviation, significant differences in associated mechanical behaviour are observed on a reference sand with respect to the phenomenon of ‘static’ liquefaction. Wet tamping favours the initiation of liquefaction instability, whereas dry pluviation favours a more stable behaviour, less susceptible to liquefaction. Microscopic observation of corresponding sand specimens allows us to identify two well differentiated structures, i.e., for wet tamping, an irregular structure with predominance of aggregates (aggregated grains) and macropores, very contractant and unstable and, for dry pluviation, a more regular structure, without macropores, more dilatant and more stable. These observations show the importance of further characterization, based on the introduction of appropriate parameters, of the initial structure of sandy materials, strongly dependant upon their mode of formation (natural or artificial). To cite this article: N. Benahmed et al., C. R. Mecanique 332 (2004).     

Sources of Complexity in Human Systems

Complex is a special attribute we can give to many kinds of systems. Although it is used often as a synonym of difficult, it has a specific epistemological meaning, which is going to be shared by the incoming science of complexity. Difficult is an object which, by means of an adequate computational power, can be deterministically or stochastically predictable. On the contrary complex is an object which can not be predictable because of logical impossibility or because its predictability would require a computational power far beyond any physical feasibility, now and forever. For complexity refers to some observing system, it is always subjective, and thus it is defined as observed irreducible complexity. Human systems are affected by several sources of complexity, belonging to three classes, in order of descending restrictivity. Systems belonging to the first class are not predictable at all, those belonging to the second class are predictable only through an infinite computational capacity, and those belonging to the third class are predictable only through a trans-computational capacity. The first class has two sources of complexity: logical complexity, directly deriving from self-reference and Gödel's incompleteness theorems, and relational complexity, resulting in a sort of indeterminacy principle occurring in social systems. The second class has three sources of complexity: gnosiological complexity, which consists of the variety of possible perceptions; semiotic complexity, which represents the infinite possible interpretations of signs and facts; and chaotic complexity, which characterizes phenomena of nonlinear dynamic systems. The third class coincides with computational complexity, which basically coincides with the mathematical concept of intractability. Artificial, natural, biological and human systems are characterized by the influence of different sources of complexity, and the latter appear to be the most complex.