碰摩转子映射系统的延迟反馈混沌控制

将转子的碰摩映射地擦边轨道附近进行局部化,并通过实验数据去拟合局部映射,然后采用变量延迟反馈控制法对该系统进行控制,通过选取合适的控制增益,将转子系统的碰磨运动镇定到周期1转道上,从而实现对碰磨转子系统混沌运动的控制。     

磁摩转子系统中的碰擦分岔现象

对于旋转机械中的常见故障这一－－转子与定子碰摩，应用非线性动力学理论分析了一个简单碰摩转子系统的碰擦分岔现象。通过对运动微分方程的数值积分。研究了转速比变化时系统具有的各种形式的分岔。结果表明：系统的运动具有周期与混沌运动交替、周期递增现象，倍周期分岔，以及随控制参数的减小运动从的周期轨道分岔为混沌吸引了。系统的这非线性特征对于准确地诊断这一故障具有重要意义。     

异步进动转子与限位器碰摩试验

利用限位器来限制储能飞轮实验转子的大幅度低频异步进动,设计了转子与限位器碰摩试验装置,研究转子的碰摩振动。分析了转子内表面碰摩力对转子运动的影响。转子与内置式限位器发生稳定的局部碰摩时,转子低频进动幅值不再增加,转子自转速度保持不变。碰摩转子的强迫振动在时域及频域都表现出了复杂性,碰摩冲击作为宽频激励,能够激励出转子-支承系统的第二模态正向进动。     

基于Hertz接触理论的转子碰摩模型

对转子系统转、定子碰摩故障的过程进行了研究，建立了一个基于Hertz接触理论的转子非线性碰摩模型。通过对不同碰摩模型进行理论分析及数值仿真的对比研究表明：基于Hertz接触理论的非线性碰摩模型能更深刻地反映转、定子碰摩过程的本质特征，具有较好的实用价值。     

具有裂纹-碰摩耦合故障转子-轴承系统的动力学研究

以非线性动力学和转子动力学理论为基础，分析了带有碰摩和裂纹耦合故障的弹性转子系统的复杂运动，在考虑轴承油膜力的同时构造了含有裂纹和碰摩故障转子系统的动力学模型。针对短轴承油膜力和碰摩-裂纹转子系统的强非线性特点，采用Runge-Kutta法对该系统由碰摩和裂纹耦合故障导致的非线性动力学行为进行了数值仿真研究，发现该类碰摩转子系统在运行过程中存在周期运动、拟周期运动和混沌运动等丰富的非线性现象，该研究结果为转子-轴承系统故障诊断、动态设计和安全运行提供理论参考。     

非线性刚度不平衡转子径向碰摩动力学研究

以线性项和立方项之和来表示转轴材料的物理非线性因素,建立了考虑非线性油膜力和非线性刚度的轴转子系统的动力学模型,利用数值积分法对转子系统由于局部碰摩故障导致的非线性动力学行为进行了研究,发现此类非线性振动系统具有倍周期分岔、拟周期和混沌等复杂的动力学行为,为此类系统的安全运行和有效识别转子故障提供了理论参考。     

转子有碰摩和支承松动故障时的非线性特性研究

以具有支承松动的Jeffcott转子为研究对象，并考虑到转子系统转子和定子间的碰摩现象，分析了支承松动和碰摩对转子系统刚度的影响，建立了转子系统振动的微分方程，并用数值方法分析了其非线性动力学特性。数值分析表明，转子在碰摩和支承松动这两种非线性因素的作用下，表现出复杂的非线性行为。     

油膜支承转子系统动静件碰摩特征分析

以支承在油膜轴承上的Jeffcott转子为对象，分析了油膜力对碰摩转子动力学行为的影响。通过与刚支情形对比，发现油膜力是耦合作用于碰摩转子系统，有时能够抑制振动，有时却加剧振动。因此实际转子碰摩故障诊断过程中，必须在充分考虑支承情况的基础上建立合理的非线性动力学模型，才能为实际转子系统的碰摩故障分析提供必要的理论依据。     

一类油膜转子刚性碰摩模型的动力学研究

本文结合非线油膜力模型和冲量定理，建立了Ｊｅｆｆｃｏｔｔ转子碰摩的刚性约束模型，通过对模型的数值模拟，揭示了转子系统碰摩产生的途径的过程，并 混沌运动发生的条件及其与碰摩的关系。     

系统参数对碰摩转子稳态响应的影响

本文基于线性碰摩力模型,分析了转定子存在偏心时柔性JEFFCOTT转子的碰摩响应。通过数值仿真,揭示了转子碰摩响应与系统参数之间的定性关系,指出较小的定子刚度、较大的系统阻尼有利于抑制转子的混沌振动。     

Vibration characteristics of a hydraulic generator unit rotor system with parallel misalignment and rub-impact

The object of this research aims at the hydraulic generator unit rotor system. According to fault problems of the generator rotor local rubbing caused by the parallel misalignment and mass eccentricity, a dynamic model for the rotor system coupled with misalignment and rub-impact is established. The dynamic behaviors of this system are investigated using numerical integral method, as the parallel misalignment, mass eccentricity and bearing stiffness vary. The nonlinear dynamic responses of the generator rotor and turbine rotor with coupling faults are analyzed by means of bifurcation diagrams, Poincaré maps, axis orbits, time histories and amplitude spectrum diagrams. Various nonlinear phenomena in the system, such as periodic, three-periodic and quasi-periodic motions, are studied with the change of the parallel misalignment. The results reveal that vibration characteristics of the rotor system with coupling faults are extremely complex and there are some low frequencies with large amplitude in the 0.3–0.4× components. As the increase in mass eccentricity, the interval of nonperiodic motions will be continuously moved forward. It suggests that the reduction in mass eccentricity or increase in bearing stiffness could preclude nonlinear vibration. These might provide some important theory references for safety operating and exact identification of the faults in rotating machinery.     

Dynamic characteristics of a rub-impact rotor-bearing system for hydraulic generating set under unbalanced magnetic pull

Electromagnetic and mechanical forces are main reasons resulting in vibrations in hydraulic generating set. The non-symmetric air-gap between the rotor and stator creates an attraction force called unbalanced magnetic pull (UMP). The UMP can produce large oscillations which will be dangerous to the machines. In this paper, the nonlinear dynamic characteristics of a rotor-bearing system with rub-impact for hydraulic generating set under the UMP are studied. The rubbing model is established based on the classic impact theory. Through the numerical calculation, the excitation current, mass eccentricity, stiffness of shaft and radial stiffness of stator are used as control parameters to investigate their effect on the system, by means of bifurcation diagrams, Poincaré maps, trajectories and frequency spectrums. Various nonlinear phenomena including periodic, quasi-periodic and chaotic motions are observed. The results reveal that the UMP has significant influence in the response of the rotor system that the continuous increase in the excitation current induces the alternation of quasi-periodic and chaotic motions, the co-occurrence of oil whip and rub in a wide excitation range aggravates the vibration and leads to the instability of the system. In addition, the large eccentricity and radial stiffness of stator, as well as the small stiffness of shaft may lead to the occurrence of full annular rubbing while increasing the stiffness of the shaft can play an important role of suppressing the chaotic motion, reducing the vibration and improving stability of the system.     

NONLINEAR THERMAL ANALYSIS FOR THE INTER-SHAFT BEARING UNDER THE DYNAMIC LOAD 1)

中介轴承作为双转子系统高低压转子重要的支承部件,其内圈和外圈均随着低压转子和高压转子高速旋转, 其传热问题更加突出.本文研究中介轴承在非线性动载荷作用下的非线性热行为.基于双转子系统动力学响应定义中介轴承动载荷,考虑中介轴承的径向游隙、分数指数非线性和参数激励等非线性因素,中介轴承动载荷会出现跳跃和双稳态等非线性行为. 考虑润滑剂的黏温关系,根据Palmgren经验公式建立动载荷作用下中介轴承的热传递模型,通过数值求解得到中介轴承稳态温度,发现动载荷的非线性行为导致中介轴承温度出现跳跃和双稳态等非线性热行为.分析转速比、偏心距、中介轴承径向游隙、Hertz接触刚度和滚子数目对中介轴承温度及非线性热行为的影响,表明偏心距、径向游隙和刚度只影响非线性热行为,而转速比和滚子数目对两者都有重要影响. 本文研究表明,动载荷相较于静载荷更适合描述中介轴承的实际载荷,由于双转子系统具有非线性振动特性, 中介轴承的热行为也表现出复杂的非线性行为.     

动载荷作用下中介轴承的非线性热行为研究

中介轴承作为双转子系统高低压转子重要的支承部件,其内圈和外圈均随着低压转子和高压转子高速旋转, 其传热问题更加突出.本文研究中介轴承在非线性动载荷作用下的非线性热行为.基于双转子系统动力学响应定义中介轴承动载荷,考虑中介轴承的径向游隙、分数指数非线性和参数激励等非线性因素,中介轴承动载荷会出现跳跃和双稳态等非线性行为. 考虑润滑剂的黏温关系,根据Palmgren经验公式建立动载荷作用下中介轴承的热传递模型,通过数值求解得到中介轴承稳态温度,发现动载荷的非线性行为导致中介轴承温度出现跳跃和双稳态等非线性热行为.分析转速比、偏心距、中介轴承径向游隙、Hertz接触刚度和滚子数目对中介轴承温度及非线性热行为的影响,表明偏心距、径向游隙和刚度只影响非线性热行为,而转速比和滚子数目对两者都有重要影响. 本文研究表明,动载荷相较于静载荷更适合描述中介轴承的实际载荷,由于双转子系统具有非线性振动特性, 中介轴承的热行为也表现出复杂的非线性行为.      

Bifurcation analysis of reduced rotor model based on nonlinear transient POD method

The singularity theory is applied to study the bifurcation behaviors of a reduced rotor model obtained by nonlinear transient POD method in this paper. A six degrees of freedom (DOFs) rotor model with cubically nonlinear stiffness supporting at both ends is established by the Newton's second law. The nonlinear transient POD method is used to reduce a six-DOFs model to a one-DOF one. The reduced model reserves the dynamical characteristics and occupies most POM energy of the original one. The singularity of the reduced system is analyzed, which replaces the original system. The bifurcation equation of the reduced model indicates that it is a high co-dimension bifurcation problem with co-dimension 6, and the universal unfolding (UN) is provided. The transient sets of six unfolding parameters, the bifurcation diagrams between the bifurcation parameter and the state variable are plotted. The results obtained in this paper present a new kind of method to study the UN theory of multi-DOFs rotor system.     

Nonlinear dynamic behaviors of a rotor-labyrinth seal system

The nonlinear model of rotor-labyrinth seal system is established using Muszynska’s nonlinear seal forces. We deal with dynamic behaviors of the unbalanced rotor-seal system with sliding bearing based on the adopted model and Newmark integration method. The influence of the labyrinth seal one the nonlinear characteristics of the rotor system is analyzed by the bifurcation diagrams and Poincare’ maps. Various phenomena in the rotor-seal system, such as periodic motion, double-periodic motion, quasi-periodic motion and Hopf bifurcation are investigated and the stability is judged by Floquet theory and bifurcation theorem. The influence of parameters on the critical instability speed of the rotor-seal system is also included.     

弹性转子实验台的响应分析

建立了考虑轴承和隔振垫弹性的非对称支承转子实验台系统的非线性动力学碰摩模型, 应用数值分析的方法对其进行研究. 以转速为分叉参数,结合Poincar\'{e}截面和自相关函数图等, 分析隔振垫刚度对系统分叉与混沌动力学行为的影响. 分析结果表明, 隔振垫刚度对系统动力学行为有较大影响, 系统通向混沌的道路主要是阵发性分叉和倍周期分叉. 实验分析所得到的系统运动性质与数值模拟结果一致.     

转子与定子碰摩的非线性动力学研究

转子与定子碰摩的动力学行为及其与系统参数关系对旋转机械设计和安全运行至关重要. 转子/定子碰摩系统是一类多参数控制的高维非光滑强非线性系统, 其动力学行为非常复杂. 本文主要从动力学与控制的角度对过去半个世纪有关转子与定子碰摩的研究成果进行归纳和总结, 其目的在于帮助读者尽可能全面系统地了解该问题的研究现状, 提炼尚待解决的问题, 以求推动转子与定子碰摩研究的进一步深入, 并为解决实际问题提供帮助. 本文将首先从碰摩局部模型和碰摩系统模型两个方面对已有的转子/定子碰摩系统的建模进行了简单的划分和归类. 其次, 以典型碰摩非线性响应为主线, 分别介绍了有关同频碰摩响应、谐波周期碰摩响应、准周期局部碰摩响应、干摩擦自激反向全周涡动响应、碰摩的全局响应行为以及碰摩响应的分岔与混沌方面的研究成果. 接下来讨论了在主被动抑制碰摩振动方面取得的结果. 最后, 给出结论并提出有待进一步研究的问题.     

非线性转子-机匣系统的分岔行为研究

建立了一类非线性转子-机匣系统的碰摩模型.应用数值分析的方法对其进行研究,得到了不同参数变化下系统响应随转速变化的分岔图,分析了系统参数变化对分岔过程的影响,并作出了在相应参数状态和特定转速下的Poincare截面图,揭示系统参数变化对非线性碰摩转子-机匣系统分岔特性的影响.     

Dynamics and stability of turbocharger rotors

The paper discusses the bifurcation and stability behavior of (automotive) turbochargers with full-floating ring bearings. Turbocharger rotors exhibit a highly nonlinear behavior due to the nonlinearities introduced by the floating ring bearings. A flexible multibody model of the rotor/bearing system is presented. Numerical run-up simulations are compared with corresponding test rig measurements. The nonlinear oscillation effects are thoroughly investigated by means of simulated and measured rotor vibrations. The influence of various system parameters on the bifurcation behavior of the rotor/bearing system is analyzed. The article examines rotors supported in full-floating ring bearings with plain circular bearing geometry in the inner and outer oil gap. By recapitulating the well-known oil whirl and oil whip phenomena for single and double oil film bearings, the paper gives an overview on the fundamental dynamic effects occurring in turbocharger systems.