面向微穿孔板吸声结构和吸声特性混合设计的软件平台

微穿孔板吸声结构是由微穿孔板与板后空腔组成的共振吸声结构,被认为是继多孔吸声材料之后发展起来的最有吸引力的吸声结构,其吸声特性与结构参数孔径d、板厚t、孔距b及空腔深度D有关,如何按需设计一个有效的微穿孔板吸声结构已成为目前研究的热点。本文从微穿孔板吸声结构和吸声特性混合设计的角度出发,使用面向对象的编程语言C++开发了微穿孔板吸声结构设计平台。与以往设计方法不同,本文开发的软件平台综合考虑了结构参数和吸声特性参数两方面的限制,根据实际应用要求平衡微穿孔板吸声结构的最大吸声系数与吸声带宽之间的制约关系,并以饱满的吸声曲线为目标,提供满足混合设计要求的优化结构参数。     

微穿孔板吸声结构水下应用研究

马大猷教授提出的微穿孔板吸声结构在空气噪声降低和隔离方面得到了广泛的应用,但未见水下应用的相关研究和报道。本文将空气中微穿孔板理论应用到水中,得到了水下微穿孔板吸声结构的吸声公式。通过理论分析,得出了微穿孔板结构直接应用于水中无法获得宽频吸收的结论。提出了通过匹配液将微穿孔板间接应用到水下的设想。设计了单层板和双层板吸声结构,并对它们的吸声特性进行了理论分析与仿真。结果表明,本文设计的微穿孔板吸声结构在水中能够获得优于空气中的宽频带吸声效果。实验测量了自制的微穿孔板吸声结构,吸声系数的测量值与理论曲线基本吻合,从而验证了理论分析的正确性。     

穿纤维微穿孔板吸声系数的有限元仿真

为拓宽微穿孔板的吸声频带,该文用有限元算法建立了典型微穿孔板和穿入不同数量金属纤维的微穿孔板模型,研究了两种微穿孔板的吸声系数、声阻抗和微孔内法向质点速度的空间分布,并进行了试验验证。有限元仿真和试验数据表明:穿入金属纤维可以拓宽微穿孔板的吸声频带,吸声系数也随纤维根数的增加而下降;吸声系数仿真结果与试验结果趋势一致,仿真模型可以有效模拟穿入纤维前后微穿孔板的吸声特性;穿入金属纤维导致黏滞效应引起的低质点速度区域增大,声阻增加,引起吸声系数的降低,而声抗变化不大。研究发现,有限元仿真方法适用于结构相对复杂的微穿孔结构的声学建模,能直观地体现微孔复杂结构的影响,值得继续深入研究和工程应用。     

阻尼耦合双层微穿孔板吸声体研究

提出并研究一种利用两板间微缝进行阻尼耦合的双层微穿孔板(DMPP)吸声体。该吸声体在两层微穿孔板(MPP)之间形成一个宽度小于1mm的微缝,因此其阻尼不仅可由板上的微穿孔提供,还可由两板之间形成的微缝提供。采用声电类比法建立了DMPP转移阻抗的理论模型,并进行实验验证,结果表明理论计算结果与实验吻合较好。然后利用建立的理论模型,对单层MPP和DMPP吸声体的吸声性能进行了对比研究,结果表明,相比于单层MPP,DMPP可以利用微缝提供的阻尼显著改善吸声性能,同时减少实际板厚。最后,对DMPP吸声体的吸声性能及其几何参数的关系进行研究,结果表明,当保持其它结构参数不变时,微缝宽度对DMPP吸声系数的提高存在一个最优值,超过或低于此值会导致吸声系数下降。     

水下弹性微穿孔吸声结构吸声系数研究

利用模态叠加法建立了水介质微穿孔板的数学模型,基于声电类比法得到其等效电路模型。研究了弹性微穿孔板和弹性背腔对垂直入射吸声系数的影响。与空气介质中的微穿孔板不同,水下微穿孔板因结构阻抗不足,难以取得满意的吸声效果,为此提出了增强型微穿孔吸声结构,并在水介质阻抗管内对理论结果予以验证。结果表明,随着增强型弹性微穿孔板弯曲刚度的增大,其在[20,2000]Hz范围内的平均吸声系数得到提高,逐步趋近于刚性微穿孔板的结果,弹性背板使微穿孔吸声结构的吸声峰向低频移动,低频吸声效果得到提高。      

穿孔率和穿孔直径耦合下微穿孔板吸声体整体吸声性能

微穿孔板几何参数的耦合性及其对整体吸声性能的影响,对于设计微穿孔板吸声体和优化其工作性能具有指导作用。根据微穿孔板吸声体基本理论,研究了穿孔率和穿孔直径双参数耦合作用下微穿孔板吸声体的整体吸声性能。穿孔率和穿孔直径之间的耦合性与其本身取值密切相关,而与板厚和板后腔深无明显关系;在穿孔率-穿孔直径参数域上,吸声体存在吸声系数为1.0的吸收峰,整体吸声性能随穿孔率或穿孔直径从小到大变化,呈现出先增强后减弱的变化趋势。该结论能够准确解释微穿孔板受粉尘污染后吸声性能的变化规律和演变路径。论文的工作为设计微穿孔板吸声体提供了一种新的理论依据和实施方法。      

内置谐振器的轻薄宽频吸声器结构设计与分析*

微穿孔板吸声器的吸声频带相较于亥姆霍兹谐振器更宽,但其低频吸声的实现需要较大的空气背腔,这对结构尺寸有限制的场合存在一定局限性。本文设计了一种轻薄吸声降噪结构(内置亥姆霍兹谐振器的微穿孔板吸声器,简称MPPHR),将微穿孔板吸声器与亥姆霍兹谐振器进行了结合,提升吸声器的低频吸声性能的同时兼具了微穿孔板宽带吸声的优点。首先基于微穿孔板和亥姆霍兹谐振器理论建立了等效电路模型并计算了结构的声阻抗。然后通过有限元对MPPHR的吸声特性进行了参数研究。最后验证了MPPHR的声阻抗模型和有限元仿真的准确性。研究结果表明：MPPHR结构拥有更宽吸声频带,厚度仅为30mm的MPPHR的半吸收频带可达1294Hz,相较于同等厚度下的微穿孔板吸声器宽近500Hz。此外,MPPHR拥有更好的低频吸声效率。     

三层微穿孔板的优化设计及特性分析

根据马大猷的微穿孔板理论,计算了三层微穿孔板的吸声系数.应用遗传算法对其结构参数进行了优化,并对其吸声特性进行了分析研究,与优化后的双层微穿孔板结构进行比较,结果表明:经过遗传算法优化后的三层微穿孔板在频域上能够获得更加饱满的吸声系数曲线,接近传统吸声材料的吸声性能.并且通过实验验证了优化设计的结果.     

一种微穿孔板消声器

本文根据马大猷教授提出的“微穿孔板吸声体精确理论”，在对微穿孔板消声器结构参数与吸声特性之间的相互影响进行了分析的基础上，设计了微穿孔板消声器并将其应用在新舟60飞机APU(辅助动力装置)降噪的实际工程中，并通过编写的噪音数据采集分析程序，对降噪效果进行了测试和分析，验证出微穿孔板消声器对消除飞机的APU的排气噪声具有良好的消声效果，平均降噪7．16dB。     

微穿孔板几何参数估算及其对吸声性能的影响

不规则孔微穿孔板几何参数无法直接获知,造成吸声性能计算困难,故提出一种微穿孔板几何参数估算方法。将不规则孔等效处理为圆孔,利用马氏理论关于圆孔微穿孔板的基本理论,建立了微穿孔板几何参数估算模型;将参数估算结果用于吸声性能预测,理论计算与实验结果吻合。根据微穿孔板几何参数对高吸声性能区域的影响,探讨了马氏理论适用极限与微穿孔板几何参数的关系,以及微穿孔板受粉尘污染后吸声性能演变规律。将微穿孔板参数点取在面积较大的高吸声性能区域中间部位,可获得较大的马氏理论适用极限;微穿孔板参数点位于高吸声性能区域右上部位时,一定程度的粉尘污染不会降低吸声性能.      

Optimization of multiple-layer microperforated panels by simulated annealing

Sound absorption by microperforated panels (MPP) has received increasing attention the past years as an alternative to conventional porous absorbers in applications with special cleanliness and health requirements. The absorption curve of an MPP depends on four parameters: the holes diameter, the panel thickness, the perforation ratio, and the thickness of the air cavity between the panel and an impervious wall. It is possible to find a proper combination of these parameters that provides an MPP absorbing in one octave band or two, within the frequency range of interest for noise control applications. However, when a wider absorption frequency band is required, it is necessary to design multiple-layer MPP (ML-MPP). The design of an N-layers MPP depends on 4N parameters. Consequently, the tuning of an optimal ML-MPP by exhaustive search within a prescribed frequency band becomes impractical. Therefore, simulated annealing is proposed in this paper as a tool to solve the optimization problem of finding the best combination of the constitutive parameters of an ML-MPP providing the maximum average absorption within a prescribed frequency band.     

水下微穿孔吸声体结构设计与试验研究

根据马大猷院士的微穿孔板(MPP)理论,提出在可设计的夹芯复合隐身结构的空腔中附加微穿孔板层的水下微穿孔吸声体。基于微穿孔板的精确计算理论及水下声隐身结构的特点,考虑空腔深度、穿孔板厚度、穿孔直径及穿孔率等对微穿孔板吸声性能的影响,对水下微穿孔吸声体进行了结构设计。利用脉冲声管法对水下微穿孔吸声体试样的吸声系数进行了测量,结果表明:水下微穿孔吸声体有效地拓宽了低频吸声频带,其微穿孔板结构参数的影响规律也与理论分析一致;对于多种吸声机理并存的水下微穿孔吸声体的空腔个数、形状及谐振特性等也是影响吸声性能的重要因素,在实际的工程应用中必须结合所关心的频带对水下微穿孔吸声体进行匹配优化设计。     

Enhancement of low-frequency sound absorption of microperforated panels by adding a mechanical impedance

In order to solve the bad low frequency sound absorption of the Micro-Perforated panel(MPP)absorber,mechanical impedance was introduced in the back of the MPP absorber to form a composite structure.According to the same particle vibration velocity on both sides of a plate,the mechanical impedance plate transfer matrix could be obtained.The units of the mechanical impedance,cavity and MPP were connected in series with the use of the transfer matrix method,thus creating the composite structure’s theoretical calculation model.The quality factor affecting absorption bandwidth was analyzed.Bandwidth is inversely proportional to the mechanical impedance plate mass.During the experiments,when at close to 400 Hz,the composite structure reached an absorption peak with a coefficient of above 0.8.Experimental results concurred with theoretical calculations.Mechanical resonance is added based on the traditional MPP resonance sound absorption mechanism.Through this,the performance of low frequency sound absorption can be improved without increasing the thickness of the structure.The frequency band can be broadened by reducing the mechanical impedance plate mass and controlling its boundary-damping coefficient.     

Sound absorption of microperforated panel mounted with helmholtz resonators

Microperforated panel (MPP) absorbers have been widely used in noise reduction and are regarded as a promising alternative to the traditional porous materials. However, the absorption bandwidth of a single-layer MPP is insufficient to compete with the porous materials. In order to improve the sound absorption ability of the single-layer MPP, MPP mounted with Helmholtz resonators (MPPHR) is introduced. Based on the MPP, Helmholtz resonators theory and electro-acoustical equivalent circuit principle, sound absorption properties of MPPHR are studied. Simulation and experimental results show that MPPHR have two peak frequencies and one anti-resonant frequency. The low-frequency peak is dependent on the Helmholtz resonators, while the high frequency peak is close to the peak of the single-layer MPP. The low-frequency sound absorption peaks move to low frequency with the neck length and the volume of Helmholtz resonators increasing. The high-frequency sound absorption peaks move to high frequency with the volume of Helmholtz resonators cavity increasing. Multiple Helmholtz resonator parallel MPP structure can provide more sound absorption than single MPPHR at low frequency range due to the introduction of more additional sound absorption peaks.     

A theoretical study on the effect of a permeable membrane in the air cavity of a double-leaf microperforated panel space sound absorber

A double-leaf microperforated panel absorber (DLMPP) is composed of a two microperforated panel (MPP) with a air cavity in-between, and without any backing structure. It shows a Helmholtz-type resonance peak absorption and additional low frequency absorption, therefore it can be used as a wideband space sound absorber. In this study, a theoretical study is made to examine the effect of a permeable membrane inside the air-cavity. Permeable membranes are studied in our previous studies and proved to be effective to improve the sound absorption performance of various type MPP sound absorbers. We investigate the absorption characteristics of a DLMPP with a permeable membrane in the cavity through numerical examples, and also studied the effect of honeycomb in the cavity of the same sound absorption structure.     

Optimising the absorption and transmission properties of aircraft microperforated panels

A method for evaluating the absorption and transmission performances of multi-layer micro-perforated structures whose facings are excited by different noise sources is described here. It is applied to determine if the acoustical performances of a number of Micro-Perforated Panels (MPPs), optimised both in absorption and transmission, exceed those of typical aircraft panels undergoing internal and external acoustic excitations. A fully-coupled modal formulation is presented that accounts for the effects of the sub-structure volumetric resonances on the acoustical properties of the partitions. It is validated against full-scale measurements performed with a pressure–velocity probe and a laser vibrometer to estimate the absorption and transmission coefficients of single- and double-layer micro-perforated partitions. The model is used to optimise the sound power dissipated by three layouts obtained from a typical aircraft partition by micro-perforating the trim panel (MPP–Porous–Panel), removing the fibreglass material (MPP–Cavity–Panel) and adding a second MPP inside the separating cavity (MPP–MPP–Panel). It is concluded that the MPP–Porous–Panel and MPP–MPP–Panel layouts provide excess interior noise reduction above 1.8 kHz and 1.2 kHz respectively, whereas the MPP–Cavity–Panel is not acoustically more efficient than a typical aircraft panel.     

A pilot study on improving the absorptivity of a thick microperforated panel absorber

Microperforated panel (MPP) absorbers are promising as a basis for the next-generation of sound absorbing materials. MPPs are typically made of a thin metal or plastic panel. However, thin limp panels are generally not suitable as an interior finish of room walls because they do not have sufficient strength, which prevents practical application of MPPs as an interior finish of room walls. In order to overcome the lack of appropriate strength required for room walls, it is possible to make an MPP out of a thick panel. However, thick MPPs are usually not efficient because the resistance and/or reactance become too high. In this study, trial production of thick MPPs and measurement of their normal absorption coefficients were carried out. Results show that efficient absorption can be given with a thick MPP by using a tapered perforation.     

Experimental study on sound absorption performance of microperforated panel with membrane cell

Microperforated panel (MPP) absorbers have been widely used in noise reduction and are regarded as a promising alternative to the traditional porous materials. However, the absorption bandwidth of a single-layer MPP is insufficient to compete with the porous materials. In order to improve the sound absorption ability of the single-layer MPP, a composite MPP sound absorber with membrane cells (MPPM) is introduced. Sound absorption properties of the MPPM are studied by the impedance tube experiment. Results show that the membranes have a significant influence on the sound impedance. The sound absorption performance of MPPM gradually increases with the increase of the membrane area. The single-layer MPP with some small area membrane cells may have the same effect and single large area membranes. By adjusting the size of the membrane cells, one can implement a sound absorber with a wider absorption bandwidth and higher absorption peaks than the single-layer MPP.     

Improvement of sound absorption characteristics under low frequency for micro-perforated panel absorbers using super-aligned carbon nanotube arrays

Super-aligned carbon nanotube (SACNT) arrays are grown on the surface of micro perforated panel (MPP) in the hope of improving the acoustic performance of MPP absorbers by virtue of their unique properties. Scanning electron microscopy reveals that SACNT arrays did not block the perforations of MPPs or changed the perforation diameter due to their “super-aligned” nature, although MPPs are thickened. The absorption effect of SACNT arrays which are of the same and different lengths with different incident side on MPP absorbers are investigated, and standing wave tube method is used to determine the normal sound absorption coefficient. Results show that both of the lengths of SACNT arrays and the incident side have effects on the sound absorption performance of MPP absorbers. And generally SACNT arrays help to improve the sound absorption capacity of MPP absorbers in low-frequency regions only when the SACNT arrays surface is the incident side. SACNT arrays decrease absorption performance of MPP absorbers when the MPP surface is used as the incident side. Moreover, SACNT arrays are found to increase the acoustic ability of MPP absorbers with the same structure parameters monotonically at lengths up to 600 μm in the condition that the SACNT arrays surface is used as the incident side.