基于SNGR方法的后缘噪声数值模拟

采用随机噪声产生和传播(SNGR)方法对后缘噪声进行数值模拟.SNGR方法结合随机方法和计算流体力学,耗费较少的计算资源就可以预测噪声水平.数值模拟时采用有限体积法求解雷诺平均Navier-Stokes(RANS)方程;采用有限差分法求解声学扰动方程,数值格式采用色散关系保持(DRP)格式,远场边界条件采用无反射边界条件.以二维平板和NACA0012翼型为例,编制程序,与参考结果对比表明,程序可以预测后缘噪声.     

湍流强度对风力机翼型气动性能的影响

本文通过采用Transition-SST湍流模型对UMY02-T01-26风电机组专用翼型绕流流场的数值计算,探究了湍流强度对风力机翼型气动性能的影响。结果表明,随着湍流强度的提高,翼型升力系数由前缘失速转变为混合失速。在一定的攻角范围内,升力系数略有增大。对于攻角处于升力系数非线性增长区域范围内,湍流强度的增大导致翼型壁面最大负压值增大。当湍流强度变化时,其壁面上出现层流分离泡的位置大小随之发生变化。此外,本文通过流场分析进一步确定了层流分离泡的产生与变化。     

二维地效翼及地效流动特性数值研究

用数值模拟的方法,对二维NACA0012翼型在地面效应下的空气动力特性和地效流动特性进行研究,得到地效翼的升力、阻力和翼型表面压力分布随攻角及相对飞行高度的变化情况.通过对计算结果的分析,可以看出,在一定的攻角,靠近地面飞行,机翼的升力得到提高;随着飞行高度的降低,地面效应增强,机翼的失速攻角减小;地面附近的粘性流动对机翼的空气动力特性影响很小;当相对飞行高度小于0.1时,应该考虑空气的可压缩性.     

用二维时域有限差分法计算机翼雷达散射截面

应用二维时域有限差分(FDTD)程序计算二维翼型NACA0012和金属方柱的双站雷达散射截面,与国内外文献上的结果进行比较,证明该程序的有效性.而后计算二维不同形状机翼的双站雷达散射截面(RCS)和不同后掠角时后掠翼和三角翼的双站RCS,得出不同形状机翼有不同的RCS分布;改变后掠角的大小可以改变机翼的RCS分布.因此,根据设计要求,可以通过选用不同机翼形状或不同大小的后掠角,使飞行器达到RCS减缩.     

振荡翼型非定常气动特性数值模拟

本文采用URANS方法对NACA0012翼型在不同振荡方式下的非定常气动特性进行了数值模拟,并与实验和文献中DNS计算结果进行对比,结果显示:URANS方法较好地显示出翼型的俯仰振荡气动特性和近壁面速度随攻角变化规律,但未能模拟出前缘分离泡的生成和发展;对于沉浮振荡翼型,URANS方法能够模拟出尾涡的结构和尾涡间的相互作用。文中还对低频和高频振荡翼型的气动特性进行了分析。     

机翼表面结冰热力学模型

基于Messinger控制体的思想建立了翼型表面的冰生长热力学模型,论述了模型的求解方法;采用边界层积分法计算LHTC(Local Heat Transfer Coefficient),并嵌入了粗糙度对表面换热的影响;计算得到的LHTC与文献中的结果做了比较验证。本文编制了冰形计算程序模块,集成到自主开发的预测软件中,模拟了不同结冰气象条件下,NACA0012翼型在4°攻角时表面槽状冰、混合冰、楔形冰的形成。数值模拟的结果与文献中提供的实验结果吻合良好,表明本文所用模型及方法可行且有效.     

低Reynolds数翼型绕流主动控制技术

在低Reynolds数条件下,翼型绕流的上表面边界层由于抗逆压梯度能力变差容易发生流动分离,从而形成长层流分离泡.分离泡通常是非定常的,会诱发边界层的转捩、再附并形成湍流边界层.这个过程会使翼型的气动性能急剧下降,并伴随着强非线性效应.转捩后形成的湍流边界层也会产生高摩擦阻力.针对这种现象,文章以NACA0012翼型为例,通过隐式大涡模拟研究了有效的主动控制方案.为了统一分离控制技术和湍流边界层减阻技术,研究了在平板或槽道湍流中取得较好控制效果的壁面垂向反向控制方案.首先利用隐式大涡模拟研究了低Reynolds数条件下NACA0012翼型绕流的流场特征.其次分析并验证了反向控制方案在分离区控制流场的可行性,发现反向控制在分离区的作用相当于基于流场信息的壁面抽吸控制,且控制具有实时性和高效性,控制抽吸了前缘的低能流体,使得翼型前缘附面层变薄,并增强了其抗逆压梯度的能力,较大程度提高了翼型的气动性能.最后在湍流边界层验证了其减阻控制效果,发现反向控制阻断了流向涡的法向输运,抑制了涡结构的发展,并减弱了猝发过程,使得湍流的高摩阻力得到了有效降低.      

基于修正的RNGκ-ε模型的水翼空化数值模拟

基于全空化模型,提出了修正RNGκ-ε模型,并对NACA0015水翼的非定常空化流场进行了数值研究。基于标准RNGκ-ε模型和修正的RNGκ-ε模型,在8°和20°两种冲角及Re=3×10~5的条件下,针对不同空化数,分别预测了翼型周围的速度场、翼型表面的空穴形态以及非定常空化时空泡的演化过程。和试验结果对比,两个湍流模型都能较好地捕捉翼型周围的大空泡团,其中,标准的RNGκ-ε模型能较好捕捉翼型头部的空穴,修正的RNGκ-ε湍流模型能更好地模拟翼型表面的空穴形态、空泡脱落过程及其产生的回流。     

用涡方法数值模拟运动物体非定常流场

采用涡方法对静止圆柱绕流、简谐振动圆柱、静止NACA0012翼型绕流和运动扑翼的非定常流场进行了数值模拟和数值验证,对比验证结果较好.控制方程采用二维不可压缩N-S方程,根据算子分裂法,对流和扩散分别采用不同的时间步长.涡方法基于Lagrange坐标系的特点使其方便模拟运动物体的非定常流场.本文的工作为今后的翼型动态失...     

超临界翼型的跨音速抖振特性

以二维非定常N-S方程为基本方程,计算跨音速翼型升力系数的时间历程.根据升力系数的脉动量急剧上升的起始点确定抖振起始边界,以超临界机翼DFVLR-R2和传统翼型NACA0012为研究对象,研究了两种翼型的抖振特性,计算结果表明,在超临界翼型的设计马赫数附近,超临界翼型具有良好的抖振特性.     

基于物理机制模型的民机机体噪声预测

为实现民机总体方案快速评估与优化迭代设计,文章对民机增升装置前缘缝翼及后缘襟翼分别建立了基于民机噪声物理机制的预测模型,在此基础上搭建了机体噪声预测体系,开发了相应的预测工具UNICRAFT.为评估预测工具UNICRAFT的计算精度和效率,文章分别针对翼吊式布局,前缘缝翼/Fowler式襟翼形式,以及尾吊式布局,前缘缝翼\双缝子翼加后退式襟翼形式的增升装置进行了计算校核验证,通过与声学风洞试验结果对比分析,验证了本文发展的预测工具及预测体系的有效性,能够实现飞机级噪声水平的高效预测.      

后掠叶片锯齿尾缘宽频噪声实验研究

本文采用线性传声器阵列分别对具有常规尾缘及锯齿形尾缘的后掠叶片的尾缘噪声进行了实验测量;运用CLEAN-SC数据处理方法精确地识别出叶片尾缘噪声的声学参数.并且基于多组实验结果的对比,深入研究了不同的尾缘锯齿长度、周期、几何比例对后掠叶片尾缘噪声降噪效果的影响.实验结果表明:在低湍流度、自由来流情况下,在总声压级降噪方...     

Symbolic regression modeling of noise generation at porous airfoils

Based on data sets from previous experimental studies, the tool of symbolic regression is applied to find empirical models that describe the noise generation at porous airfoils. Both the self noise from the interaction of a turbulent boundary layer with the trailing edge of an porous airfoil and the noise generated at the leading edge due to turbulent inflow are considered. Following a dimensional analysis, models are built for trailing edge noise and leading edge noise in terms of four and six dimensionless quantities, respectively. Models of different accuracy and complexity are proposed and discussed. For the trailing edge noise case, a general dependency of the sound power on the fifth power of the flow velocity was found and the frequency spectrum is controlled by the flow resistivity of the porous material. Leading edge noise power is proportional to the square of the turbulence intensity and shows a dependency on the fifth to sixth power of the flow velocity, while the spectrum is governed by the flow resistivity and the integral length scale of the incoming turbulence.     

An experimental study of airfoil instability tonal noise with trailing edge serrations

This paper presents an experimental study of the effect of trailing edge serrations on airfoil instability noise. Detailed aeroacoustic measurements are presented of the noise radiated by an NACA-0012 airfoil with trailing edge serrations in a low to moderate speed flow under acoustical free field conditions. The existence of a separated boundary layer near the trailing edge of the airfoil at an angle of attack of 4.2 degree has been experimentally identified by a surface mounted hot-film arrays technique. Hot-wire results have shown that the saw-tooth surface can trigger a bypass transition and prevent the boundary layer from becoming separated. Without the separated boundary layer to act as an amplifier for the incoming Tollmien–Schlichting waves, the intensity and spectral characteristic of the radiated tonal noise can be affected depending upon the serration geometry. Particle Imaging Velocimetry (PIV) measurements of the airfoil wakes for a straight and serrated trailing edge are also reported in this paper. These measurements show that localized normal-component velocity fluctuations that are present in a small region of the wake from the laminar airfoil become weakened once serrations are introduced. Owing to the above unique characteristics of the serrated trailing edges, we are able to further investigate the mechanisms of airfoil instability tonal noise with special emphasis on the assessment of the wake and non-wake based aeroacoustic feedback models. It has been shown that the instability tonal noise generated at an angle of attack below approximately one degree could involve several complex mechanisms. On the other hand, the non-wake based aeroacoustic feedback mechanism alone is sufficient to predict all discrete tone frequencies accurately when the airfoil is at a moderate angle of attack.     

Broadband trailing edge noise from a sharp-edged strut

This paper presents experimental data concerning the flow and noise generated by a sharp-edged flat plate at low-to-moderate Reynolds number (Reynolds number based on chord of 2.0 × 10(5) to 5.0 × 10(5)). The data are used to evaluate a variety of semi-empirical trailing edge noise prediction methods. All were found to under-predict noise at lower frequencies. Examination of the velocity spectra in the near wake reveals that there are energetic velocity fluctuations at low frequency about the trailing edge. A semi-empirical model of the surface pressure spectrum is derived for predicting the trailing edge noise at low-to-moderate Reynolds number.     

锯齿尾缘降噪翼型优化设计研究

大量研究工作表明旋转风电叶片的主要气动噪声来自叶尖尾缘区域,一直以来都是严重影响居民生活和叶片气动性能发挥的重要因素之一.为此,针对决定叶片重要气动特性单元——二维翼型,采用有别于传统的仿猫头鹰翅膀锯齿尾缘流动控制方法,将锯齿关键尺寸参数融入到风力机翼型设计之中,从而开发仿生锯齿翼型的优化设计方法,获得低噪声与高气动性...     

Tuning of turbulent boundary layer anisotropy for improved surface pressure and trailing-edge noise modeling

The modeling of the surface pressure spectrum beneath a turbulent boundary layer is investigated, focusing on the case of airfoil flows and associated trailing edge noise prediction using the so-called TNO model. This type of flow is characterized by the presence of an adverse pressure gradient along the airfoil chord. It is shown that discrepancies between measurements and results from the TNO model increase as the pressure gradient increases. The original model is modified by introducing anisotropy in the definition of the turbulent vertical velocity spectrum across the boundary layer and by considering a frequency-dependent vertical correlation length. The degree of anisotropy is directly related to the strength of the pressure gradient. It is shown that by appropriately normalizing the pressure gradient and by tuning the degree of anisotropy, experimental results can be closely reproduced by the modified model. The model is validated against Large Eddy Simulation results and additional wind tunnel measurements. It is further validated in the context of trailing edge noise for which the model formulation makes use of the above surface pressure spectrum.     

Noise due to turbulent flow past a trailing edge

A theoretical method [I] for calculating far field noise from an airfoil in an incident turbulent flow is extended to apply to the case of noise produced by turbulent flow past a trailing edge, and some minor points of the theory in reference [1] are clarified. For the trailing edge noise, the convecting surface pressure spectrum upstream of the trailing edge is taken to be the appropriate input. The noise is regarded as generated almost totally by the induced surface dipoles near the trailing edge and thus equal, but anticorrelated, noise is radiated into the regions above and below the airfoil wake, respectively. The basic assumption of the analysis, from which these concepts of appropriate input and dominance of dipole sources follow, is that the turbulence remains stationary in the statistical sense as it moves past the trailing edge. The results show that such trailing edge noise often is quite small, compared say to that produced by typical oncoming turbulence levels of one percent, but that it might be appreciable for an airfoil with a flow separation, or for a blown flap.     

静子尾缘喷气后尾迹与动叶干涉噪声研究

尾缘喷气技术已经广泛地用于航空发动机和多级压缩机等领域,用以降低动静叶片间的相互干涉作用以提高透平机械的气动性能,并降低动静干涉噪声.本文对尾缘喷气用于低压轴流风机进行了详细的研究,对轴流风机的上游静叶实施尾缘喷气,通过实验测量,尾缘喷气使静叶尾迹达到无动量亏损尾迹状态能够降低风机噪声,文章还提出了基于CFD数值模拟的尾迹与动叶相互干涉的噪声预测模型,预测结果和实验结果比较接近.     

Open rotor tone scattering

This paper describes a method for calculating the scattering of open rotor tones by an adjacent surface such as the aircraft fuselage or wing. This is of practical importance because shielding by these structures could be used to significantly reduce community noise levels. In the first part of this paper the propeller is modelled as a rotating point source and the effect of propeller translation is neglected. The scattering of sound from this rotating point source by either a rigid circular cylinder or a rigid half-plane is calculated and the reflection/shielding effect is clearly demonstrated. In the second part of this paper, the point source/stationary medium model is extended to include the effect of distributed sources and a moving medium. The extended model is then applied to calculate the effect of scattering of rotor-alone tones by a wing (which is modelled as an infinite half-plane). The effect of wing sweep and the application of the Kutta-condition at the trailing edge is investigated. An approximate method for quickly calculating open rotor tone scattering is also developed and validated.