水热反应中籽晶层对ZnO纳米棒的影响

以Zn(NO3)2·6H2O/HMT为反应物,通过低温水热反应过程,在籽晶衬底上制备了ZnO纳米棒,分别用场发射扫描电子显微镜和X射线衍射仪对ZnO纳米棒形貌与晶体结构进行了表征,并研究了不同方法制备的ZnO籽晶层以及籽晶层厚度对ZnO纳米棒形貌及结晶质量的影响.结果表明磁控溅射籽晶衬底上生长的ZnO纳米棒结晶质量最好,而籽晶层的厚度对ZnO纳米棒的垂直取向性有一定的影响.     

水热法制备Co掺杂ZnO纳米棒及其光学性能

采用水热法在石英衬底上以Zn(CH3COO)2.2H2O和Co(NO3)2.6H2O水溶液为源溶液,以C6H12N4(HMT)溶液作为催化剂,在较低温度下制备了Co掺杂的ZnO纳米棒。采用X射线衍射(XRD)和扫描电子显微镜(SEM)对所生长ZnO纳米棒的晶体结构和表面形貌进行了表征,考察了Co掺杂对ZnO纳米棒微观结构和对发光性能影响的机制。结果表明:Co掺杂的ZnO纳米棒呈六方纤锌矿结构,具有沿(002)面择优生长特性,Co掺杂使ZnO纳米棒的直径变细;同时室温光致发光(PL)谱检测显示Co掺杂ZnO纳米棒具有很强的近带边紫外发光峰,而与深能级相关的缺陷发光峰则很弱。本研究采用水热法在石英衬底上于较低温度下生长出了具有较高光学质量的Co掺杂ZnO纳米棒。     

水浴法制备ZnO纳米棒及其场发射性能

用硝酸锌(Zn(NO3)2·6H2O)与六亚甲基四胺(C6H12N4)以等浓度配制成反应溶液,通过水浴法制备出了形貌可控的棒状ZnO纳米结构,讨论了不同反应浓度及衬底对ZnO表面形貌的影响.样品的XRD和扫描电子显微镜分析结果表明,所得产物均为六方纤锌矿结构,在有晶种层的衬底上制备出的ZnO纳米棒沿(001)方向并垂直于衬底表面生长.随着反应浓度的增加,ZnO纳米棒的直径增大,长径比减小.样品的场发射性能测试表明,反应溶液浓度为0.005 mol/L,以铜膜为晶种层的硅衬底上制备出的场发射阴极具有较好的场发射性能.     

Cu2O-ZnO异质结太阳能电池的制备及光电性能研究（英文）

电化学沉积是一种绿色高效的材料制备方法。本实验使用电化学沉积法分别制备了单晶的氧化锌(ZnO)纳米棒阵列和p型的氧化亚铜(Cu2O)薄膜,并对样品进行了扫描电镜、X光衍射、外量子效率和光电性能测试等一系列的表征和测试。试验结果表明,通过改变反应溶液中的ZnCl2浓度可以来调控ZnO纳米棒的直径。光电性能测量显示在Cu2O/ZnO间形成了p-n异质结。量子效率的测试证明该异质结可有效地促进载流子的分离和传送,从而提高太阳能电池的转化效率。     

ZnO/Cu_2O异质结纳米阵列制备及光催化性能

利用湿化学法在FTO玻璃基底上制备了高度规整的ZnO纳米棒阵列(ZnO NRAs),以此为衬底,采用磁控溅射法在ZnO NRAs表面沉积Cu_2O薄膜。分别用X射线衍射仪、X射线光电子能谱、扫描电镜、光致光谱、紫外可见分光光度计和电化学工作站对样品的物相、形貌、吸收光谱、光电性能进行了表征,用甲基橙(MO)模拟有机物废水研究复合材料的光催化性能。结果表明:ZnO纳米棒为六方纤锌矿结构,其直径约为80~100 nm,长约2~3μm,棒间距约100~120 nm。立方晶系的Cu_2O颗粒直径约为100~300 nm,形成致密膜层并紧密覆盖在ZnO NRAs表面上,构成ZnO/Cu_2O异质结纳米阵列(ZnO/Cu_2O HNRAs)结构。与纯ZnO NRAs和Cu_2O相比,ZnO/Cu_2O HNRAs在可见光范围内的吸收显著增强,吸收波长向可见光方向偏移。ZnO/Cu_2O HNRAs的载流子传递界面的电荷转移速度快,有效促进了光生电子和空穴的分离。在紫外-可见光照射65 min后,ZnO/Cu_2O HNRAs的降解效率为94%,分别是纯ZnO NRAs和Cu_2O的18倍和1.7倍。     

ZnO纳米棒/CdS量子点的制备及紫外-可见探测性能研究

本文采用水热法在ITO衬底上制备了ZnO纳米棒阵列,然后用化学水浴沉积法在纳米棒上制备CdS量子点。分别利用SEM和XRD对样品形貌和晶体结构进行表征。结果表明,球状的CdS量子点均匀地包覆在ZnO纳米棒表面,且结晶质量较好。基于ZnO纳米棒和ZnO纳米棒/CdS量子点制备的探测器对紫外光都具有很好的响应,然而与ZnO纳米棒探测器相比,ZnO纳米棒/CdS量子点探测器在相同条件下的光电流提高了7倍,为0. 52 mA。此外,ZnO纳米棒/CdS量子点探测器对绿光和蓝光也表现出了很好的响应。     

水热法制备均一形貌的ZnO微米棒

以Zn（Ac）2· 2H2O、KI和N2H4· H2O反应物,在未使用任何表面活性剂的简单水热反应体系中制得了ZnO微米棒.采用X射线粉末衍射仪（XRD）、扫描电子显微镜（SEM）对产物的晶体结构、形貌进行了表征和分析.测试结果表明,所得产物为六方纤锌矿结构ZnO微米棒,平均直径为1μm,长度4μm.     

ZnO纳米棒的制备及紫外探测性能

通过水热法在ITO衬底上成功合成了ZnO纳米棒,并以ITO为电极制备了ZnO纳米棒紫外探测器件。在室温下测试了所制备器件对紫外光的响应性能。测试结果表明,ZnO纳米棒对紫外光有很好的光响应,在0V附近,ZnO纳米棒紫外探测器的灵敏度能达到1500。此外,通过循环测试可以观测到ZnO纳米棒紫外探测器具有良好的重复性和稳定性。     

醋酸锌热解温度对ZnO纳米棒的结构及光学性质的影响

采用水热法在普通载玻片上热解醋酸锌生成的ZnO种子层上制备ZnO纳米棒, 采用 X射线衍射仪、扫描电镜、分光光度计等测试手段详细研究了醋酸锌热解温度对 ZnO纳米棒的结构和光学性质的影响. 结果表明: 纳米棒的结晶质量、端面尺寸、宏观应力和透射率与醋酸锌热解温度有密切关系. 随着热解温度的增加, ZnO纳米棒具有的c轴择优取向性先增强后减弱, 拉应力先减小后增大, 可见光区的平均透射率先增大后减小. 热解温度为350 ℃时, ZnO纳米棒c轴择优取向性最强, 拉应力最小, 平均透射率最大. 端面尺寸诱导的表面散射 是影响ZnO纳米棒可见光区平均透射率的主要机制. 关键词： 醋酸锌 水热法 ZnO纳米棒     

直立Zn_2GeO_4/ZnO纳米棒阵列的制备及其发光性质研究

利用化学气相沉积法(CVD)在表面溅射Au和沉积ZnO籽晶的硅衬底上分别生长高度有序、垂直密布的直立Zn2GeO4/ZnO纳米棒阵列,利用扫描电子显微镜(SEM)、X射线衍射仪(XRD)和光致发光(PL)谱测试手段对所制备样品进行表征和发光特性的研究。所制备的Zn2GeO4/ZnO纳米棒的直径为350~400 nm,高度为10~11μm;室温PL谱观察到3个来源于Zn2GeO4的典型发光峰。最后,对CVD法制备的Zn2GeO4/ZnO纳米棒生长机理进行了分析。该种直立性良好的一维纳米棒材料可以广泛地应用到纳米光电子器件中。     

Preparation and room temperature NO_2-sensing performances of porous silicon/V_2O_5nanorods

In this paper, porous silicon/V₂O₅ nanorod composites are prepared by a heating process of as-sputtered V film on porous silicon (PS) at 600 ℃ for different times (15, 30, and 45 min) in air. The morphologies and crystal structures of the samples are investigated by field emission scanning electron microscope (FESEM), x-ray diffractometer (XRD), x-ray photoelectron spectroscopy (XPS), and Raman spectrum (RS). An improved understanding of the growth process of V₂O₅ nanorods on PS is presented. The gas sensing properties of samples are measured for NO₂ gas of 0.25 ppm～3 ppm at 25 ℃. We investigate the effects of the annealing time on the NO₂-sensing performances of the samples. The sample obtained at 600 ℃ for 30 min exhibits a very strong response and fast response-recovery rate to ppm level NO₂, indicating a p-type semiconducting behavior. The XPS analysis reveals that the heating process for 30 min produces the biggest number of oxygen vacancies in the nanorods, which is highly beneficial to gas sensing. The significant NO₂ sensing performance of the sample obtained at 600 ℃ for 30 min probably is due to the strong amplification effect of the heterojunction between PS and V₂O₅ and a large number of oxygen vacancies in the nanorods.     

LaPO4:Eu3+@SiO2核壳结构发光纳米棒的制备与表征

在不加任何表面活性剂的条件下,通过水热法直接合成了LaPO4:Eu3+纳米棒,并采用溶胶-凝胶法在其表面修饰了一层SiO2,得到了LaPO4:Eu3+@SiO2纳米棒.XRD分析表明,样品包覆前后均属于单斜晶系的独居石型的LaPO4.FTIR分析表明,LaPO4:Eu3+粒子与SiO2是以化学键的形式结合在一起.由TE...     

Room temperature NO_2-sensing properties of hexagonal tungsten oxide nanorods

Hexagonal WO_3 nanorods were synthesized through a facile hydrothermal method. The nanorods properties were investigated by scanning electron microscope(SEM), transmission electron microscope(TEM), energy dispersive spectroscopy(EDS), and x-ray diffraction(XRD). The NO_2-sensing performances in terms of sensor response, response/recovery times and repeatability at room temperature were optimized by varying the heat treatment temperature of WO_3 nanorods. The optimized NO_2sensor(400-℃-annealed WO_3 nanorods) showed an ultra-high sensor response of 3.2 and short response time of 1 s to 5-ppm NO_2. In addition, the 400-℃-annealed sample exhibited more stable repeatability.Furthermore, dynamic responses measurements of annealed samples showed that all the annealed WO_3 nanorods sensors presented p-type behaviors. We suppose the p-type behavior of the WO_3 nanorods sensor to be that an inversion layer is formed in the space charge layer when the sensor is exposed to NO_2 at room temperature.Therefore, the 400-℃-annealed WO_3 nanorods sensor is one of the most energy conservation candidates to detect NO_2 at room temperature.     

Synthesis and characterization of novel vanadium dioxide nanorods

Novel vanadium dioxide nanorods were fabricated via a surfactant-assisted hydrothermal method at 180 °C for 48 h in the presence of cetyltrimethylammonium bromide (CTAB). The self-assembled samples were characterized by XRD, SEM, TEM, HRTEM and FT-IR. The results show that the products are nanorods, which are pure B phase vanadium dioxide with high crystallinity. The obtained nanorods have diameters of 40-60 nm with lengths up to 1-2 um. The probable formation mechanism of vanadium dioxide is also discussed.     

具有阵列-簇双层结构的TiO2纳米棒的光电性能（英文）

选择硫酸氧钛(TiOSO4)作为无机钛源前驱体,通过温和的水热法在掺氟氧化锡导电玻璃基底(FTO)上直接合成单晶金红石相TiO2纳米棒薄膜,呈现阵列-簇双层结构。在模拟太阳光照射下,该纳米棒薄膜的短路电流可达到0.17 mA/cm2,是相同条件下由四异丙醇钛[Ti(iPro)4]为有机钛源而制备的TiO2纳米棒薄膜的2倍多。实验结果表明,多维层状结构和无机硫酸氧根离子(OSO4-4)的存在对TiO2纳米棒薄膜的光电流响应有促进作用。     

Facile Synthesis of Single‐Phase Mesoporous Gd2O3:Eu Nanorods and Their Application for Drug Delivery and Multimodal Imaging

In this work, a new and facile strategy is developed to synthesize a single‐phase Eu³⁺‐doped mesoporous gadolinium oxide nanorods (MS‐Gd₂O₃:Eu@PEG) by incorporating a facile wet‐chemical route, which includes an induced silica layer being coated onto the nanorods, and evolution of pores and formation of channels, as well as a surface‐modified process for multimodal imaging and anti‐cancer drug delivery. The properties of these as‐prepared Gd₂O₃:Eu nanorods are characterized by transmission electron microscopy (TEM), X‐ray diffraction (XRD), N₂ adsorption/desorption, and photoluminescence (PL). The in vitro cytotoxicity test, drug loading, and drug release experiments reveal that the MS‐Gd₂O₃:Eu@PEG nanorods have good biocompatibility, efficient loading capacity, and pH‐sensitive releasing behavior, suggesting the nanorods could be an ideal candidate as drug delivery vehicles for cancer therapy. Furthermore, the MS‐Gd₂O₃:Eu@PEG nanorods show clearly dose‐dependent contrast enhancement in T₁‐weighted magnetic resonance images and can potentially be used as a T₁‐positive contrast agent. These results indicate our prepared multifunctional mesoporous gadolinium oxide nanorods can serve as a promising platform for simultaneous anti‐cancer drug delivery and multimodal imaging.     

反胶束软模板法合成PANI/TiO2纳米棒复合材料及其性能研究

以阳离子表面活性剂十六烷基三甲基溴化胺(CTAB)形成的反胶束为模板,制备了一系列不同纳米TiO2含量的PANI/TiI2纳米复合材料.利用FTIR,UV-Vis,TG,TEM和荧光光谱等方法对产物进行了结构表征和性能研究.探讨了反胶束体系中PANI/TiO2复合纳米棒形成的自组装机理.结果表明:复合材料主要为直径30～40 nm,长约400 nm的PANI/TiO2复合纳米棒,二氧化钛纳米粒子与聚苯胺大分子之间存在强的相互作用,并对复合材料的热稳定性起到提高作用,PANI/TiO2纳米复合材料在紫外和可见光区域均有吸收,并在416 nm处激发产生荧光,荧光强度随着掺杂TiO2含量的提高得到了较大的增强.通过PANI/TiO2纳米棒复合材料中的激子离化和电荷传输过程探讨了PANI/TiO2的荧光量子效率和荧光强度增加的机理.     

Synthesis of tin nanorods via a sonochemical method combined with a polyol process

Metallic tin nanorods were synthesized by a sonochemical method employing the polyol process. In the reaction a solution of SnCl2 in ethylene glycol was exposed to high-intense ultrasound irradiation. The phase and elemental compositions, and thermal properties of the as-synthesized samples were characterized by XRD, EDX, SAED, XPS, DSC, TGA, and BET measurements. The morphologies of the products were further characterized with SEM, TEM, and HRTEM. The results show that crystallized metallic tin nanorods in diameters of 50-100 nm and in lengths of up to 3 microm were synthesized. The nanorods are encapsulated in a thin layer containing Ti and carbon compounds. On the basis of the obtained data, a possible mechanism of the formation of tin nanorods was proposed.     

实验条件对二氧化钛纳米棒形貌和光电流密度的影响

采用简单的水热合成法,以四异丙醇钛为钛源,制备出整齐有序的二氧化钛纳米棒阵列。探索了钛源浓度、反应液酸度、反应时间、温度等实验条件对纳米棒的形貌和光电流密度的影响。实验结果表明:钛源浓度和反应液酸度对纳米棒的生长有非常大的影响,最佳反应液的组分为10 mL去离子水、10 mL盐酸和0.4 mL钛源。另外,随着反应时间的增加,纳米棒的长度会明显的增加,但纳米棒的直径和光电流密度却变化不大。同时,纳米棒的长度也随着反应温度的增高而增加,其光电流密度随之呈现先增大后减小的趋势,但其直径没有明显改变。     

Large scale and controllable preparation of W_2C nanorods or WC nanodots with peroxidase-like catalytic activity

W_2C nanorods or WC nanodots are prepared via an easy,shape-controllable and large-scale preparation technique.Results reveal that each of the W_2C nanorods and WC nanodots has a peroxidase-like activity.Besides,the peroxidase-like activity of W_2C is the first time to be demonstrated.The catalytic efficiency of W_2C nanorods is much higher than that of WC nanodots and chemical condition range of W_2C can be wider than that of WC,which indicates that W_2C is likely to be used as artificial mimetic peroxidase or in-situ amplified colorimetric immunoassay.