Ar离子注入YBa2Cu3O7—x超导薄膜中微结构变化的透射电子显微镜研究

Ar离子注入YBa_2Cu_3O_(7-x)超导薄膜后,不仅会引起样品超导转变温度T_c和临界电流密度J_c的下降,还会使样品的正常态由金属型变为半导体型。透射电子显微镜观察发现在小剂量(<5×10~(12)Ar/cm~2)注入情况下,样品的晶格结构几乎不受影响。随着注入剂量的增加,晶格损伤越来越严重,最终变成非晶态。对实验结果的分析表明,Ar离子注入引起YBa_2Cu_3O_(7-x)薄膜超导性能的变化主要与O原子子晶格的无序化过程有关。     

Co,Zn元素对YBa2Cu3O7-δ的不同的掺杂效应

对单相掺杂样品YBa₂Cu_3-xCo_xO_y (x=0.00,0.025,0.05,0.075,0.10,0.125,0.15,0.20,0.25,O.275,0.30,0.325,0.35,0.375,0.40)和YBa₂Cu_3-xZn_xO_y(x=O.025,0.05,0.075,0.10,0.15,0.20,0.30)作了室温下的 关键词：     

正交和四方YBa2Cu3O7-x的热膨胀系数

用电容法测量了正交和四方YBa₂Cu₃O_7-x的热膨胀系数与温度的关系。结果表明,正交样品在205K附近,四方样品在92—130K之间热膨胀系数有异常。估计前者可能与晶格的不稳定性有关,说明具有较强的电-声子相互作用,后者可能与结构转变有关,因此破坏了高温超导电性。同时也发现正交样品在92K热膨胀系数有微小跳跃。由此估计了压力效应 关键词：     

YBa2Cu3O7-xc轴方向临界电流的测定

本文测量了熔化织构法生长(MTG)的和通常烧结法制备的YBa₂Cu₃O_7-x块状样品的传输临界电流密度T_c以及磁场-样品不同取向的磁滞回线。MTG样品的J_c在78K和零场时达到3.5×10⁴A/cm²,实验提供了有力的证据表明如此高的J_c主要是由于块状样品内弱连接的消除,因为MTG块状样品的整体J_c与烧结样品颗 关键词：     

YBa2Cu3O7-x高温导电性的研究

本文将以YBa₂Cu₃O_7-x的高温实验为基础,分析和讨论了氧对YBa₂Cu₃O_7-x高温导电性的影响以及一维Cu—0链的导电作用。还报道了一种新现象,即在高温下,一旦氮气被换成氧气,YBa₂Cu₃O_7-x就迅速地发生从半导体到金属的结构相变。 关键词：     

Lu2Ti2O7和Lu2TiO5陶瓷材料的Kr离子辐照损伤研究

钛酸盐因其优异的物理化学性能，可作为高放射性核废物（HLW）和锕系元素（钚）的重要候选固化材料之一。采用传统的陶瓷烧结工艺制备了多晶的Lu₂Ti₂O₇和Lu₂TiO₅陶瓷材料。在室温下，用800 keVKr2+对两种材料进行辐照，辐照后的样品采用GIXRD进行表征，观察到两种样品都经历了先肿胀、然后再发生非晶相变的过程。不同的是Lu₂Ti₂O₇的晶格肿胀程度大于Lu₂TiO₅。另外，Lu₂TiO₅样品的辐照到2×10₁₄ ions/cm₂时非晶含量达95.54%，而Lu₂Ti₂O₇样品在此剂量下非晶含量只有74.66%。通过第一性原理计算了Lu₂Ti₂O₇晶体的晶格肿胀随反位浓度的变化关系，结果表明，Lu₂Ti₂O₇出现非晶前的晶格肿胀主要由阳离子反位导致，而Lu₂TiO₅是无序的萤石结构，其辐照所导致的晶格肿胀不含阳离子反位的贡献，晶格肿胀程度较低。     

C60薄膜的离子注入损伤研究

在200 keV重离子加速器上，用120—360 keV的H,N,Ar和Mo离子注入C₆₀薄膜．对注入后薄膜的拉曼谱进行了分析．结果表明，不同离子注入C₆₀薄膜后，C₆₀的1469 cm^-1特征峰随注入剂量的增加均呈指数式下降，同时在1300—1700 cm^-1范围出现非晶碳峰，并逐渐增强，最终完全非晶化．而且1469 cm^-1拉曼峰的强度及C₆₀薄膜完全非晶化所对应的剂量与注入离子的种类和能量有关．进一步的分析表明，C₆₀分子的损伤主要是由注入离子的核能量转移所造成，与电子能量转移无关．H离子注入C₆₀薄膜后，1469 cm^-1处特征拉曼峰向短波方向非对称展宽，这可能是注入的H离子通过电子能量转移使C₆₀分子发生聚合的结果. 关键词：     

Co离子注入TiO2薄膜的显微结构和磁性研究

利用直流磁控溅射技术在玻璃衬底上沉积了TiO₂薄膜,并对其进行了Co离子注入,最后在真空中500 ℃退火50 min,得到系列薄膜样品. 利用剥离-分散方法制备了薄膜的透射电镜样品,并用扫描电镜(SEM)、X射线能量散射谱(EDX)和高分辨透射电镜(HRTEM)对样品做了近似原位观察,研究了薄膜样品中不同Co离子注入深度的成分分布和显微结构. 结果表明,薄膜呈锐钛矿结构,Co元素主要分布在薄膜表层,Co离子的注入使TiO₂薄膜的晶粒被部分破坏,并形成CoO,而5 关键词： 2薄膜')" href="#">Co注入TiO₂薄膜 电镜原位观察 室温铁磁性     

Fe离子注入多晶Al2O3的光电子能谱研究

本文应用光电子能谱(XPS)方法分析Fe离子注入多晶Al₂O₃样品中各离子的存在状态。通过微机对谱峰进行高斯拟合处理,得出注入离子Fe不同价态的相对含量。 关键词：     

氧缺位对单相YBa2Cu3O7-x热电势率的影响

研究了氧缺位对单相YBa₂Cu₃O_7-x体系超导电性及热电势率的影响。结果表明,超导转变温度随氧缺位的增加而下降,热电势率随氧缺位的增加而增大。由实验结果推断,单相YBa₂Cu₃O_7-x的多数载流子为空穴。存在较大的声子曳引热电势表明。在YBa₂Cu₃O_7-x超导体中存在较强的电-声子相互作用。 关键词：     

Microstructural and superconducting properties of C6H6 added bulk MgB2 superconductor

The effect of aromatic hydrocarbon (benzene, C₆H₆) addition on lattice parameters, microstructure, critical temperature (T_c), critical current density (J_c) of bulk MgB₂ has been studied. In this work only 2 mol% C₆H₆ addition was found to be very effective in increasing the J_c values, while resulting in slight reduction of the T_c. J_c values of 2 mol% C₆H₆ added MgB₂ bulks reached to 1.83×10⁶ A/cm² at 15 K and 0 T. Microstructural analyses suggest that J_c enhancement is associated with the substitution of carbon with boron and which also results in the smaller MgB₂ grain size. The change in the lattice parameters or the lattice disorder is claimed as a cause of the slight reduction in the T_c by carbon addition. We note that our results show the advantages of C₆H₆ addition include homogeneous mixing of precursor powders, avoidance of expansive nanoadditives, production of highly reactive C, and significant enhancement in J_c of MgB₂, compared to un-doped samples.     

钛离子辐照对MgB2超导薄膜的载流能力和磁通钉扎能力的影响

利用混合物理化学气相沉积法(hybrid physical-chemical vapor deposition, HPCVD)可以制备出高性能的MgB₂超导薄膜, 再对薄膜进行钛(Ti)离子辐照处理.经过辐照处理后的样品被掺入了Ti元素, 与未处理的干净MgB₂样品相比,其超导转变温度没有出现大幅度的下降, 而在外加磁场下的临界电流密度得到了明显的提高,同时样品的上临界磁场也得到了提高. 在温度5 K, 外加垂直磁场为4 T的情况下, Ti离子辐照剂量为1× 10¹³/cm²的样品的临界电流密度达到了1.72× 10⁵ A/cm², 比干净的MgB₂要高出许多,而其超导转变温度仍能维持在39.9 K的较高水平.     

R1-xPrxBa2Cu3O7-δ超导Tc平台的离子尺寸效应

系统地研究了Ｒ_1-xＰｒ_xＢａ₂Ｃｕ₃Ｏ_7-δ的超导Ｔ_c与Ｐｒ替代浓度ｘ的关系。发现在离子半径ｒ_i≤ｒ_i（Ｄｙ）时，在低Ｐｒ浓度范围内存在一个超导Ｔ_c平台，并且平台宽度表明一个Ｒ^３＋离子尺寸效应。我们认为，Ｔ_c平台宽度的离子尺寸效应可能起源于Ｐｒ４ｆ电子局域态的改变。提出一个临界Ｒ^３＋离子半径ｒ_ic，ｒ_i＞ｒ_ic时ＲＢａ₂Ｃｕ₃Ｏ_7-δ的超导电性消失 关键词：     

Electron irradiation effects in doped high temperature superconductors YBa2Cu3? x M x O y (M = Fe, Ni; x=0; x =0:01)

The influence of irradiation by electrons with an energy of 8 MeV, at dose intervals between 10¹³ and 2×10¹⁸el/cm², on the properties of impurity doped, high-temperature superconductor YBa₂Cu_3−x M _x O _y (M = Fe, Ni; x=0; x=0:01) ceramics has been studied. It has been established that, as the irradiation dose is increased, the onset temperature of the transition to the superconducting state (T _c ^on ), and the intergranular weak link coupling temperature between granules (T _m ^J ), exhibit an oscillation around their initial values of approximately about 1–1.5 K. This oscillation indicates that the process of radiation defect formation in HTSC occurs in multiple stages. It was also found that the critical current (J _c )decreases with an increase of the irradiation dose, and exhibits a local minimum at a dose of 8×10¹⁶el/cm²coinciding with minima for T _c ^on and T _m ^J at this dose. It was found that the introduction of Fe atoms to the ceramic decreases T _m ^J , while introducing Ni atoms decreases both T _c ^on and T _m ^J ; it is suggested that this is a result of Ni substitution of Cu both in Cu2 plane sites and Cu1 chain sites. The introduction of Ni causes a large change in the intergranular critical current density, J _c . A critical irradiation dose is obtained (2×10¹⁸)after which all HTSC parameters strongly decrease, i. e. the superconductivity of HTSC is destroyed.      

Iron doping effect on superconducting properties of MgB2

Iron-doped MgB₂ bulks are prepared by hybridized diffusion method using nano-powder and macro-powder of pure iron as iron source. The doping effect on superconductivity transition temperature, T_c, and critical current J_c have been investigated. It is found that both T_c and J_c of MgB₂ show quite different features depending on the particle size of the dopant powders. It is demonstrated that different from iron bulk or large size powders, iron nano-powders are active dopant for MgB₂ which suppresses both T_c and J_c of MgB₂.     

Effects of RE2O3 (RE = Tm, Sc, Yb) addition on the superconducting properties of ErBa2Cu3Oy

We investigated the effects of added Tm₂O₃, Sc₂O₃, and Yb₂O₃ on the superconducting properties of sintered Er123 samples. Tm₂O₃ addition caused the least T_c degradation, exhibiting a T_c above 90 K even for 17 vol% addition. Samples with added Sc₂O₃ maintained a T_c at above 90 K up to an addition of 7.2 vol%, while Yb₂O₃-containing samples showed a monotonic decrease in T_c with increased vol% of added Yb₂O₃. Tm₂O₃-containing samples exhibited a slight increase in J_c(0.1 T)/J_c(0) and had constant J_c values even for 17 vol% addition. XRD and SEM results indicate that the Tm₂O₃ is very stable in the superconducting matrix.     

用Monte-Carlo方法计算L12结构的有序度

本文应用Monte-Carlo统计物理计算方法,计算了L1₂结构有序度随温度的变化。计算中考虑了最近邻有序相互作用J₁和次近邻有序相互作用J₂=0,-0.3J₁,0.3J₁三种情况。计算结果显示存在有序无序一级相变,临界温度T_c与准化学方法等理论结果相符,同时发现次近邻有序相互作用J₂敏感地影响到有序无序转变温度T_c,为间隙原子对L1₂结构金属间化合物塑性的作用提供了一种可能的解释。 关键词：     

Effects of neutron irradiation on superconducting properties of orthorhombic Y–Ba–Cu oxides

Abstract

We have studied the effects of fast neutron (E>0.1 MeV) irradiation at reactor (～ 360 K) and low (～ 20 K) temperatures on the superconducting properties of polycrystalline orthorhombic YBa₂Cu₃O_7?y . Measurements were made on the superconducting critical temperature T_c , critical current J_c , Meissner effect and magnetic field dependence of J_c . The T_c drops by an irradiation at reactor temperature and J_c increases with increasing fluence. On the other hand with the irradiation at low temperature, T_c rises and J_c increases. Results of observation of Meissner effect and the magnetic field dependence of J_c are consistent with the behavior of T_c and J_c .     

X-ray diffraction studies on He- and Ar-irradiated Nb3Ge thin films

We have performed measurements of relative integrated X-ray intensities in order to study the influence of radiation damage on the A15 structure of superconducting Nb₃Ge. With increasing He- and Ar-ion fluence an increase of the “temperature factor” and the lattice parameter has been observed in the fluence region where the depression of the superconducing transition temperature T_c was found to occur. Both parameters do not uniquely depend on the decrease of T_c. Further a decrease of the total relative X-ray intensity is found for particle fluences in the saturation region of T_c. The results are interpreted in terms of static atom displacements statistically distributed in the irradiated volume.     

Superconductivity of powder-in-tube Sr0.6K0.4Fe2As2 wires

Nb-sheathed Sr_0.6K_0.4Fe₂As₂ superconducting wires have been fabricated using the powder-in-tube (PIT) method for the first time and the superconducting properties of the wires have been investigated. The transition temperature (T_c) of the Sr_0.6K_0.4Fe₂As₂ wires is confirmed to be as high as 35.3 K. Most importantly, Sr_0.6K_0.4Fe₂As₂ wires exhibit a very weak J_c-field dependence behavior even the temperature is very close to T_c. The upper critical field H_c2(0) value can exceed 140 T, surpassing those of MgB₂ and all the low temperature superconductors. Such high H_c2 and superior J_c-field performance make the 122 phase SrKFeAs wire conductors a powerful competitor potentially useful in very high field applications.