基于氧化铟锡的无结低电压薄膜晶体管

在室温下制备了基于氧化铟锡(ITO)的底栅结构无结薄膜晶体管. 源漏电极和沟道层都是同样的ITO薄膜材料,没有形成传统的源极结和漏极结, 因而极大的简化了制备流程,降低了工艺成本.使用具有大电容的双电荷层SiO₂作为栅介质, 发现当ITO沟道层的厚度降到约20 nm时, 器件的栅极电压可以很好的调控源漏电流. 这些无结薄膜晶体管具有良好的器件性能: 低工作电压(1.5 V), 小亚阈值摆幅(0.13 V/dec)、 高迁移率(21.56 cm²/V·s)和大开关电流比(1.3× 10⁶). 这些器件即使直接在大气环境中放置4个月, 器件性能也没有明显恶化:亚阈值摆幅保持为0.13 V/dec,迁移率略微下降至18.99 cm²/V·s,开关电流比依然大于10⁶.这种工作电压低、工艺简单、 性能稳定的无结低电压薄膜晶体管非常有希望应用于低能耗便携式电子产品以及新型传感器领域.     

High‐performance In–Zn–O thin‐film transistors with a soluble processed ZrO2 gate insulator

Spin‐coated zirconium oxide films were used as a gate dielectric for low‐voltage, high performance indium zinc oxide (IZO) thin‐film transistors (TFTs). The ZrO₂ films annealed at 400 °C showed a low gate leakage current density of 2 × 10^–8 A/cm² at an electric field of 2 MV/cm. This was attributed to the low impurity content and high crystalline quality. Therefore, the IZO TFTs with a soluble ZrO₂ gate insulator exhibited a high field effect mobility of 23.4 cm²/V s, excellent subthreshold gate swing of 70 mV/decade and a reasonable I_on/off ratio of ～10⁶. These TFTs operated at low voltages (～3.0 V) and showed high drain current drive capability, enabling oxide TFTs with a soluble processed high‐k dielectric for use in backplane electronics for low‐power mobile display applications. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Room-temperature and solution-processed vanadium oxide buffer layer for efficient charge injection in bottom-contact organic field-effect transistors

We introduce a room temperature and solution-processible vanadium oxide (VO_x) buffer layer beneath Au source/drain electrodes for bottom-contact (BC) organic field-effect transistors (OFETs). The OFETs with the VO_x buffer layer exhibited higher mobility and lower threshold voltages than the devices without a buffer layer. The hole mobility with VO_x was over 0.11 cm²/V with the BC geometry with a short channel length (10 μm), even without a surface treatment on SiO₂. The channel width normalized contact resistance was decreased from 98 kΩ cm to 23 kΩ cm with VO_x. The improved mobility and the reduced contact resistance were attributed to the enhanced continuity of pentacene grains, and the increased work function and adhesion of the Au electrodes using the VO_x buffer layer.     

Reduction of the contact resistance in copper phthalocyanine thin film transistor with UV/ozone treated Au electrodes

Bottom-contact (BC) copper phthalocyanine (CuPc) thin film transistor with UV/ozone treated Au as a source/drain electrode was fabricated and the contact resistance was estimated from the transmission line method (TLM). Comparing the properties of OTFT with untreated Au electrode, the performance of the BC CuPc-TFT with the UV/ozone treated Au electrodes was significantly improved: saturation mobility increased from 4.69 × 10⁻³ to 2.37 × 10⁻² cm²/V s, threshold voltage reduced from −29.1 to −6.4 V, and threshold swing varied from 5.08 to 2.25 V/decade. The contact resistance of the device with UV/ozone treated Au electrodes was nearly 20 times smaller than that of the device with untreated Au electrodes at the gate voltage of −20 V. This result indicated that using the UV/ozone treated Au electrode is an effective method to reduce the contact resistance. The present BC configuration with UV/ozone treated Au electrodes could be a significant step towards the commercialization of OTFT technology.     

Low-voltage-drive and high output current ZnO thin-film transistors with sputtering SiO2 as gate insulator

Low-voltage-drive ZnO thin-film transistors (TFTs) with room-temperature radio frequency magnetron sputtering SiO₂ as the gate insulator were fabricated successfully on the glass substrate. The ZnO-TFT operates in the enhancement mode with a threshold voltage of 4.2 V, a field effect mobility of 11.2 cm²/V s, an on/off ratio of 3.1 × 10⁶ and a subthreshold swing of 0.61 V/dec. The drain current can reach to 1 mA while the gate voltage is only of 12 V and drain voltage of 8 V. The C–V characteristics of a MOS capacitor with the structure of ITO/SiO₂/ZnO/Al was investigated. The carrier concentration N_D in the ZnO active layer was determined, the calculated N_D is 1.81 × 10¹⁶ cm⁻³, which is the typical value of undoped ZnO film used as the channel layer for ZnO-TFT devices. The experiment results show that SiO₂ film is a promising insulator for the low voltage and high drive capability oxide TFTs.     

Highly stable hafnium–tin–zinc oxide thin film transistors with stacked bilayer active layers

Hf–Sn–Zn–O (HTZO) thin films were prepared on SiO₂/SiN_x substrates at room temperature by the direct current (DC) magnetron sputtering of Hf-doped Sn–Zn–O targets. The characteristics of films with different amounts of Hf were analyzed. Amorphous HTZO films were obtained by increasing the Hf content, while polycrystalline films have not shown with Hf doping. With the proper Hf concentration in the HTZO films (∼2.0 atomic % Hf/(Hf + Sn + Zn + O)), HTZO films demonstrated good performance as an oxide semiconductor channel material in thin film transistors (TFTs) with a field effect mobility (μ_FE) of 10.9 cm²V⁻¹ s⁻¹, an on/off current ratio of 10⁹, and a subthreshold voltage swing of 0.71 V/decade.     

Control of electrical properties and gate bias stress stability in solution-processed a-IZO TFTs by Zr doping

Zr-doped indium zinc oxide (IZO) thin film transistors (TFTs) are fabricated via a solution process with different Zr doping ratios. The addition of Zr suppressed the carrier concentration in the IZO films, which was confirmed by Hall Effect measurements. As the amount of Zr was increased in the oxide active layer of TFTs, the subthreshold swing (S.S) reduced, the ON/OFF ratio improved, and the threshold voltage (V_th) shifted positively. Moreover, the starting points of the ON state for TFTs near the point zero gate voltage could be controlled by the addition of Zr. The 0.3% Zr-doped IZO TFT exhibited a high saturation mobility of 7.0 cm² V⁻¹ s⁻¹, ON/OFF ratio of 2.6 × 10⁶ and S.S of 0.57 V/decade compared the IZO TFT with 10.1 cm² V⁻¹ s⁻¹, 1.7 × 10⁶ and 0.75 V/decade. The Zr effect of the gate bias stability was examined. Zr-doped IZO TFTs were relatively unstable under a positive bias stress (PBS), whereas they showed good stability at a negative bias stress (NBS). The gate bias stability of the oxide TFTs were compared with the extracted parameters through a stretched-exponential equation. The characteristic trapping time under NBS of 0.3% Zr-doped IZO TFTs was improved from 8.3 × 10⁴ s for the IZO TFT to 3.1 × 10⁵ s.     

使用铜源漏电极的非晶氧化铟锌薄膜晶体管的研究

为了实现氧化物薄膜晶体管(TFT)的低电阻布线,采用Cu作为氧化物TFT的源漏电极。通过优化成膜工艺制备了电阻率低至2.0μΩ·cm的Cu膜,分析了Cu膜的晶体结构、粘附性及其与a-IZO薄膜的界面,制备了以a-IZO为有源层和Cu膜的粘附层的TFT器件。结果表明:所制备的Cu膜呈多晶结构;引入a-IZO粘附层增强了Cu膜与衬底的粘附性;同时,Cu在a-IZO中的扩散得到了抑制。所制备的TFT的迁移率、亚阈值摆幅和阈值电压分别为12.9 cm2/(V·s)、0.28 V/dec和-0.6 V。     

Pulsed laser deposition of ZnO grown on glass substrates for realizing high-performance thin-film transistors

We report characterization of ZnO thin-film transistors (TFTs) on glass substrates fabricated by pulsed laser deposition (PLD). ZnO films were characterized by X-ray diffraction (XRD), atomic force microscopy and Hall effect measurements. The XRD results showed high c-axis-oriented ZnO(0002) diffraction corresponding to the wurtzite phase. Moreover, the crystallization and the electrical properties of ZnO thin films grown at room temperature are controllable by PLD growth conditions such as oxygen gas pressure. The ZnO films are very smooth, with a root-mean-square roughness of 1 nm. From the Hall effect measurements, we have succeeded in fabricating ZnO films on glass substrates with an electron mobility of 21.7 cm²/V s. By using the ZnO thin film grown by two-step PLD and a HfO₂ high-k gate insulator, a transconductance of 24.1 mS/mm, a drain current on/off ratio of 4.4×10⁶ and a subthreshold gate swing of 0.26 V/decade were obtained for the ZnO TFT.     

Amorphous IZO TTFTs with saturation mobilities exceeding 100 cm2/Vs

In this paper we demonstrate the use of amorphous binary In₂O₃–ZnO oxides simultaneously as active channel layer and as source/drain regions in transparent thin film transistor (TTFT), processed at room temperature by rf sputtering. The TTFTs operate in the enhancement mode and their performances are thickness dependent. The best TTFTs exhibit saturation mobilities higher than 10² cm²/Vs, threshold voltages lower than 6 V, gate voltage swing of 0.8 V/dec and an on/off current ratio of 10⁷. This mobility is at least two orders of magnitude higher than that of conventional amorphous silicon TFTs and comparable to or even better than other polycrystalline semiconductors. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effects of Ti addition on sol-gel derived InO and InZnO thin film transistors

In this study, we have newly developed titanium-indium oxide (TiInO) and titanium-indium zinc oxide (TiInZnO) thin films as the active channel layer in thin film transistors (TFTs) by the sol-gel process. The effects of adding Ti on TiInO and TiInZnO TFTs were investigated. The addition of Ti elements can suppress formation of oxygen vacancies because of the stronger oxidation tendency of Ti relative to that of Zn or In. TiInO and TiInZnO TFTs showed lower off currents and higher on/off current ratios than pure InO and InZnO TFTs. A TiInO TFT doped with 10.31 mol% Ti showed good performance with an on/off current ratio greater than 10⁷, and a field-effect mobility of 1.91 cm² V^?1 S^?1. A TiInZnO TFT doped with 2.92 mol % Ti showed an on/off current ratio greater than 10⁶, and a field-effect mobility of 0.45 cm² V^?1 S^?1.     

Highly conductive interface between a rubrene single crystal and a molybdenum oxide layer and its application in transistors

The formation of interfacial hole carriers between a rubrene single crystal and a 2 nm-thick molybdenum oxide layer resulted in the formation of a highly conductive interface with a high electrical conductivity of 0.16 S/cm and a very small activation energy of 0.03 eV. This highly conductive interface enabled charge injection and accumulation of a high drain current in the recombination zone in ambipolar transistors, resulting in a significant reduction of the driving voltage with high, balanced hole and electron mobilities of 1.1 and 0.5 cm²/V s, respectively.     

Growth of very large grains in polycrystalline silicon thin films by the sequential combination of vapor induced crystallization using AlCl3 and pulsed rapid thermal annealing

Metal-induced crystallization method is one of the favorable non-laser crystallization methods for thin-film transistors in large-area displays. However, it is necessary to reduce metal contamination in the film to lower leakage current for the device applications. A new two-step crystallization method, consisting of a nucleation step by AlCl₃ vapor-induced crystallization and a grain growth step by a pulsed rapid thermal annealing, has been proposed to increase the grain size and reduce the residual metal contamination in crystallized poly-Si films. The grain size of the poly-Si film crystallized by the VIC + PRTA two-step crystallization process was as large as 70 μm. Furthermore, the Al concentration in the poly-Si film was reduced by two orders of magnitude from 1 × 10²⁰ cm^?3 by VIC only process to 1.4 × 10¹⁸ cm^?3 by the two-step process. As a result, the minimum leakage current of poly-Si TFTs using the poly-Si film prepared by the two-step process was reduced from 1.9 × 10^?10 A/μm to 2.8 × 10^?11 A/μm at a drain voltage of 5 V, without carrier mobility degradation.     

Near infrared transparent conducting CdO nanocrystallite films codoped with boron and hydrogen

Thin films of boron and hydrogen-codoped CdO (B&H-codoped CdO) oxide with different boron content have been prepared on glass and silicon substrates. The effects of codoping on the structural, electrical, and optical properties of the host CdO films were systematically studied. The structural study shows that doped boron ions occupied locations in interstitial positions and/or Cd²⁺-ion vacancies of CdO lattice. The bandgap of B-doped CdO shrinks by 25-38% compare to hydrogenated CdO. Such bandgap narrowing was phenomenological studied in the framework of the available models. The electrical behaviours show that all the prepared B&H-doped CdO films are degenerate semiconductors. However, the hydrogenated 7.9% boron doped CdO has resistivity of 1.52 × 10⁻⁴ Ω cm, mobility of 47.5 cm²/V s, and carrier concentration of 8.6 × 10²⁰ cm⁻³. The optoelectronic measurements in visible and NIR spectral range demonstrate the utility of the oxide/p-Si heterojunction in photodetection applications.     

Specific contact resistance of IGZO thin film transistors with metallic and transparent conductive oxides electrodes and XPS study of the contact/semiconductor interfaces

In this work, the specific contact resistance (ρ_c) between amorphous indium-gallium-zinc-oxide (IGZO) semiconductor and different contact electrodes was obtained from thin film transistors (TFTs). Ti/Au (10/100 nm), aluminum doped zinc oxide (AZO, 100 nm) and indium tin oxide (ITO, 100 nm) were used as source/drain electrodes to fabricate IGZO TFTs. Chemical states of the contacts/semiconductor interfaces were examined by depth profile X-ray photoelectron spectroscopy (XPS) analysis to explain the origin of the differences on specific contact resistance. The lowest ρ_c achieved using Ti/Au was related to the formation of a TiO_x interlayer due to oxygen atoms diffusing out from the semiconductor under layer, increasing the carrier concentration of IGZO at the interface and lowering the ρ_c. On the contrary, no interfacial reactions were observed between IGZO and AZO or ITO source/drain. However, IGZO resistivity increased with ITO contacts likely due to oxygen vacancies filling during ITO deposition. This fact seems to be the origin of the high contact resistance between IGZO and ITO, compared to IGZO-AZO and IGZO-Ti/Au interfaces.     

Effect of antimony doping on the low‐temperature performance of solution‐processed indium oxide thin film transistors

The effects of antimony (Sb) doping on solution‐processed indium oxide (InO_x) thin film transistors (TFTs) were examined. The Sb‐doped InSbO TFT exhibited a high mobility, low gate swing, threshold voltage, and high I_ON/OFF ratio of 4.6 cm²/V s, 0.29 V/decade, 1.9 V, and 3 × 10⁷, respectively. The gate bias and photobias stability of the InSbO TFTs were also improved by Sb doping compared to those of InO_x TFTs. This improvement was attributed to the reduction of oxygen‐related defects and/or the existence of the lone‐pair s‐electron of Sb³⁺ in amorphous InSbO films. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

High-performance Zinc-Tin-Oxide thin film transistors based on environment friendly solution process

Zinc-Tin-Oxide (ZTO) thin films were fabricated using a simple and eco-friendly sol-gel method and their application in thin film transistors (TFTs) was investigated. Annealing temperature has a crucial influence on the structure and electrical properties of sol-gel ZTO thin films. The ZTO thin films annealed at 300–600?°C revealed smooth and uniform surfaces with amorphous state, in addition, a high optical transparency over 90% of the ZTO films in the visible range was obtained. The electrical performance of ZTO TFTs showed obvious dependence on annealing temperature. The ZTO TFTs annealed at 500?°C showed a high carrier mobility of 5.9?cm²/V, high on/off current ratio (I_on/off) of 10⁶-10⁷, and threshold voltage (V_th) of 1.03?V. To demonstrate the application of sol-gel ZTO films in low-power display fields, we also fabricated ZTO TFTs with a solution-processed high-permittivity (high-k) ZrTiO_x dielectric layer. The ZTO/ZrTiO_x TFTs showed high mobility of 17.9?cm²/V and I_on/off of 10⁵-10⁶?at a low operation voltage of 3?V, indicating that Indium-free ZTO thin films would be potential candidates for low cost, high performance oxide TFT devices.     

非晶铟镓锌氧薄膜晶体管钼/铜源漏电极的研究

针对非晶铟镓锌氧薄膜晶体管（a-IGZO TFT）的钼/铜源漏电极开展研究。实验证明,单层Mo源漏电极与栅绝缘层之间的粘附性好、表面粗糙度较小、电阻率较大,而单层Cu源漏电极与栅绝缘层之间的结合性差且Cu原子扩散问题严重、表面粗糙度较大、电阻率较小。为了实现优势互补,我们设计了双层Mo（20 nm）/Cu（80 nm）源漏电极,并采用优化工艺制备了包含该电极结构的a-IGZO TFT。器件具有良好的电学特性,场效应迁移率为 8.33 cm²·V^-1·s^-1, 阈值电压为6.0 V,亚阈值摆幅为2.0 V/dec,开关比为 1.3×10⁷,证明了双层Mo/Cu源漏电极的可行性和实用性。     

Comparison of electrochromic amorphous and crystalline electron beam deposited WO3 thin films

Tungsten oxide (WO₃) thin films were prepared by an electron beam deposition technique. Films were deposited onto fluorine-doped tin oxide (FTO)-coated glass substrates maintained at 523 K. The as-deposited films were found to be amorphous and crystallized after annealing at 673 K. The electrochromic and optical properties, structure, and morphology are strongly dependent on the annealing conditions. Cyclic voltammetry (C-V) was carried out in the potential range −1 to +1 V. Before and after colouration, the films were characterized by measuring transmittance and reflectance. The colouration efficiencies at 630 nm are about 39.4 cm² C⁻¹ and 122.2 cm² C⁻¹ for amorphous and crystalline films, respectively. An investigation of self-bleaching for the coloured film revealed that the film fades gradually over time.     

High performance Zn–Sn–O thin film transistors with Cu source/drain electrode

Zn–Sn–O (ZTO) thin film transistors (TFTs) were fabricated with a Cu source/drain electrode. Although a reasonably high mobility (μ_FE) of 13.2 cm²/Vs was obtained for the ZTO TFTs, the subthreshold gate swing (SS) and threshold voltage (V_th) of 1.1 V/decade and 9.1 V, respectively, were inferior. However, ZTO TFTs with Ta film inserted as a diffusion barrier, exhibited improved SS and V_th values of 0.48 V/decade and 3.0 V, respectively as well as a high μ_FE value of 18.7 cm²/Vs. The improvement in the Ta‐inserted device was attributed to the suppression of Cu lateral diffusion into the ZTO channel region. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)