The effect of junction temperature on the optoelectrical properties of InGaN/GaN multiple quantum well light-emitting diodes

Thermal effects on the optoelectrical characteristics of green InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) have been investigated in detail for a broad temperature range, from 30 °C to 100 °C. The current-dependent electroluminescence (EL) spectra, current–voltage (I–V) curves and luminescence intensity–current (L–I) characteristics of green InGaN/GaN MQW LEDs have been measured to characterize the thermal-related effects on the optoelectrical properties of the InGaN/GaN MQW LEDs. The experimental results show that both the forward voltages decreased with a slope of ?3.7 mV/K and the emission peak wavelength increased with a slope of +0.02 nm/K with increasing temperature, indicating a change in the contact resistance between the metal and GaN layers and the existence of a band gap shrinkage effect. The junction temperature estimated from the forward voltage and the emission peak shift varied from 25.6 to 14.5 °C and from 22.4 to 35.6 °C, respectively. At the same time, the carrier temperature decreased from 371.2 to 348.1 °C as estimated from the slope of high-energy side of the emission spectra. With increasing injection current, there was found to be a strong current-dependent blueshift of ?0.15 nm/mA in the emission peak wavelength of the EL spectra. This could be attributed to not only the stronger band-filling effect but also the enhanced quantum confinement effect that resulted from the piezoelectric polarization and spontaneous polarization in InGaN/GaN heterostructures. We also demonstrate a helpful and easy way to measure and calculate the junction temperature of InGaN/GaN MQW LEDs.     

Near-infrared photoluminescence and thermally stimulated current in Cu3Ga5Se9 layered crystals: A comparative study

Near-infrared photoluminescence (PL) and thermally stimulated current (TSC) spectra of Cu₃Ga₅Se₉ layered crystals grown by Bridgman method have been studied in the photon energy region of 1.35–1.46 eV and the temperature range of 15–115 K (PL) and 10–170 K (TSC). An infrared PL band centered at 1.42 eV was revealed at T = 15 K. Radiative transitions from shallow donor level placed at 20 meV to moderately deep acceptor level at 310 meV were suggested to be the reason of the observed PL band. TSC curve of Cu₃Ga₅Se₉ crystal exhibited one broad peak at nearly 88 K. The thermal activation energy of traps was found to be 22 meV. An energy level diagram demonstrating the transitions in the crystal band gap was plotted taking account of results of PL and TSC experiments conducted below room temperature.     

Temperature dependent photoluminescence processes in ZnO thin films grown on sapphire by pulsed laser deposition

Temperature dependence of the photoluminescence (PL) transitions in the range of 10–300 K was studied for ZnO thin films grown on sapphire by pulsed laser deposition. The low temperature PL spectra were dominated by recombination of donor bound excitons (B_X) and their phonon replicas. With increasing temperature, free exciton (F_X) PL and the associated LO phonon replicas increased in intensity at the expense of their bound counterparts. The B_X peak with line width of ∼6 meV at 10 K exhibited thermal activation energy of ∼17 meV, consistent with the exciton-defect binding energy. The separation between the F_X and B_X peak positions was found to reduce with increasing temperature, which was attributed to the transformation of B_X into the shallower donor bound exciton complexes at consecutive lower energy states with increasing temperature, which are possible in ZnO. The energy separation between F_X peak and its corresponding 1-LO phonon replica showed stronger dependence on temperature than that of 2-LO phonon replica. However, their bound counterparts did not exhibit this behavior. The observed temperature dependence of the energy separation between the free exciton and it is LO phonon replicas are explained by considering the kinetic energy of free exciton. The observed PL transitions and their temperature dependence are consistent with observations made with bulk ZnO crystals implying high crystalline and optical quality of the grown films.     

Near-white emitting QD-LED based on hydrophilic CdS nanocrystals

In this work we report fabrication of a nanocrystal (NC)-based hybrid organic–inorganic LED with structure of ITO/PEDOT:PSS/PVK/CdS-NCs/(Al or Mg:Ag). The hydrophilic CdS NCs were synthesized using a novel aqueous thermochemical method at 80 °C and sizes (around 2 nm) were controlled by thioglycolic acid (TGA) as the capping agent. The favorite feature of these NCs is their relatively high emission intensity and broad, near-white emission. The hydrophilic CdS NCs were successfully spin coated using Triton X-100 as the wetting agent. The fabricated LEDs demonstrated a turn on voltage about 7 V for Al metallic contact. The electroluminescence was a broad spectrum at 540 and 170 nm width, which was about 50 nm red shifted compared to photoluminescence spectra. The CIE color coordinates of the LED at (0.33, 0.43) demonstrated a near white light LED with an emission on green–yellow boundary of white. Annealing of the device up to 190 °C had a positive effect on the performance, possibly due to better contacts between layers. Replacing Al contacts with Mg:Ag reduced the turn-on voltage to 6 V and changed CIE color coordinate to (0.32, 0.41). The EL peak was also shifted to 525 nm, with a brightness of 15 Cd/m² at working voltage of 15 V. The current efficiency and external quantum efficiency of device were 0.08 Cd/A and 0.03% at current densities higher than 10 mA/cm².     

Spontaneous and stimulated emission in InAsSb-based LED heterostructures

Electroluminescence of LED heterostructures with active layer made of InAsSb films grown on InAs substrates was studied in the temperature range T = 4.2–300 K. At low temperatures (T = 4.2–100 K), stimulated emission was observed with an optical cavity formed normal to the growth plane. The emission became spontaneous at higher temperatures due to the resonant “switch-on” of the CHHS Auger recombination process in which the energy of a recombining electron-hole pair is transferred to a hole transitioning to the spin-orbit-splitted band. The spontaneous character of emission continued up to room temperature because of the influence of other Auger processes. The results obtained suggest that InAsSb-based LED heterostructures are promising for the fabrication of vertically-emitting mid-infrared lasers.     

Comparative study on the effects of different annealing conditions on the surface morphology,crystallinity, and optical properties of ZnO micro/nanoparticle-based discs

The effects of annealing parameters on the surface morphology, crystallinity, and optical properties of ZnO disc were investigated. Variations in the annealing temperatures and gas flow rates were found to have a profound impact; grain growth was enhanced even at the low annealing temperature of only 400 °C. SEM and AFM revealed smooth and uniform grain growth after annealing treatment, especially at 800 °C. A unique secondary growth of ZnO nanoparticles and multilayer grain growth that have not been reported elsewhere were also observed. The annealing treatment was also found to improve grain crystallinity as illustrated by the lowering of intrinsic compressive stress based on the XRD lattice constant and FWHM data. The PL spectra of the M-Disc showed a huge band edge emission at 371–376 nm. In contrast, the N-Disc exhibited a dominant and broad visible PL emission in the green band with peaks at 519–533 nm. These peaks were attributed to a very high concentration of structural defects (oxygen vacancies and zinc/oxygen interstitials). The annealing conditions had a significant effect on the properties of ZnO. Increased percentage of oxygen in the O/Ar from 50% to 100% did not change the M-Disc spectra. However, the XRD pattern of the N-Disc revealed that the (0 0 2) peak intensity decreased, the position of the (1 0 1) peak slightly shifted toward a higher angle, and the FWHM of the (1 0 1) peak improved. The experimental results showed that thermal annealing could enhance the different properties of ZnO discs.     

Exciton relaxation in Ga1 − xInxAs/GaAs self-organized quantum dots

The exciton dynamics in Ga_1 − xIn_xAs/GaAs self-organized quantum dots grown on GaAs (111)B substrates are studied by the time-resolved photoluminescence (PL). We have found the intra-dot exciton relaxation by the reduction of the linewidth and peak energy and also by the energy-dependent PL rise time in the transient PL spectra. Compared with the energy relaxation in the reference quantum wells, we have confirmed that the exciton relaxation in three-dimensionally confined quantum dots is slower than in the quantum wells.     

Temperature-dependent photoluminescence of CuInS2 quantum dots

Temperature-dependent photoluminescence (PL) spectroscopy of CuInS₂ core and CuInS₂/ZnS core–shell quantum dots (QDs) was studied for understanding the influence of a ZnS shell on the PL mechanism. The PL quantum yield and lifetime of CuInS₂ core QDs were significantly enhanced after the QD surface was coated with the ZnS shell. The temperature dependences of the PL energy, linewidth, and intensity for the core and core–shell QDs were studied in the temperature range from 92 to 287 K. The temperature-dependent shifts of 98 meV and 35 meV for the PL energies of the QDs were much larger than those of the excitons in their bulk semiconductors. It was surprisingly found that the core and core–shell QDs exhibited a similar temperature dependence of the PL intensity. The PL in the CuInS₂/ZnS core–shell QDs was suggested to originate from recombination of many kinds of defect-related emission centers in the interior of the cores.     

Influence of thickness of functional layer on performance of organic salt-doped OLED with ITO/PVK:PBD:TBAPF6/Al structure

The effect of thickness of functional layer on the electrical and electroluminescence (EL) properties of single-layer OLED with ITO/PVK:PBD:TBAPF₆/Al structure were investigated where indium tin oxide (ITO) was used as anode, poly(9-vinylcarbazole) (PVK) as polymeric host, 2-(4-biphenylyl)-5-phenyl-1,3,4-oxadiazole (PBD) as electron-transporting molecule, tetrabutylammonium hexafluorophosphate (TBAPF₆) as organic salt dopant and aluminium (Al) as cathode. A unique transition phenomenon at high bias voltage in the devices was observed and the transition was reversible. The transition voltage and turn on voltage decreased with the decrease of functional layer thickness. The turn on voltage was approximately 5.5 V and 6.5 V for 55-nm-thick and 95-nm-thick devices, respectively. However, the current efficiency of 95-nm-thick device was higher than the 55-nm-thick device. More interestingly, the Commission Internationale d’Eclairage (C.I.E.) coordinates of EL spectra of 95-nm-thick device at bias voltage ranging from 7 V to 13 V located in the white light region even without any dye doping. The PL and EL spectra were found completely different. PBD electromer was proposed to dominate the EL spectrum, but the contribution from PVK–PBD electroplex cannot be completely ruled out.     

High performance Europium(III) based emitters for electroluminescence: Synthesis,crystal structures,photophysical and electroluminescent properties

In this paper, we synthesize two 1,10-phenanline derived ligands, along with their corresponding Eu(III) complexes. Their crystal structures, photophysical characteristics, including UV–vis absorption, photoluminescence (PL), quantum yields, excited state lifetimes, and thermal stability, are discussed in detail. In addition, we also investigate their potential application in electroluminescence (EL) devices. Experimental data suggest that the two Eu(III) complexes are promising emitters for EL application: pure red emissions with a maximum EL brightness of 850 cd/m² and a maximum current efficiency of 3.67 cd/A are achieved. It is found that the elimination of active hydrogen in ligand favors most PL and EL factors, including PL quantum efficiency, thermal stability, and current efficiency, but not for maximum EL brightness. An emitter with shorter excited state lifetime leads to a higher EL brightness, regardless of its relatively lower device efficiency.     

Photoluminescence from single isoelectronic traps in nitrogen delta-doped GaAs grown on GaAs(1 1 1)A

We have studied photoluminescence (PL) observed from single isoelectronic traps formed by nitrogen pairs in nitrogen δ-doped GaAs layers grown on GaAs(1 1 1)A substrates. The PL was composed of a single peak with a narrow linewidth of ∼80 μeV. Polarized PL measurements confirmed that the emission from single isoelectronic traps in nitrogen δ-doped GaAs(1 1 1) is unpolarized irrespective of nitrogen pair arrangements. These results can be explained by in-plane isotropy of the samples, which is consistent with the symmetrical property of GaAs(1 1 1), and demonstrate that utilizing (1 1 1) substrate is an effective means for obtaining unpolarized single photons, which are desirable for the application to quantum cryptography.     

Defect related luminescence in Hg0.2Cd0.8Te nano- and micro-crystals grown by the solvothermal method

The photoluminescence (PL) properties of nano- and micro-crystalline Hg_1?xCd_xTe (x≈0.8) grown by the solvothermal method have been studied over the temperature range 10–300 K. The emission spectra of the samples excited with 514.5 nm Ar⁺ laser consist of five prominent bands around 0.56, 0.60, 0.69, 0.78 and 0.92 eV. The entire PL band in this NIR region is attributed to the luminescence from defect centers. The features like temperature independent peak energy and quite sensitive PL intensity, which has a maximum around 50 K is illustrated by the configuration coordinate model. After 50 K, the luminescence shows a thermal quenching behavior that is usually exhibited by amorphous semiconductors, indicating that the defects are related to the compositional disorder.     

A time-resolved luminescence spectroscopy study of non-linear optical crystals K2Al2B2O7

We report the results of complex study of luminescence and dynamics of electronic excitations in K₂Al₂B₂O₇ (KABO) crystals obtained using low-temperature luminescence-optical vacuum ultraviolet spectroscopy with sub-nanosecond time resolution under selective photoexcitation with synchrotron radiation. The paper discusses the decay kinetics of photoluminescence (PL), the time-resolved PL emission spectra (1.2–6.2 eV), the time-resolved PL excitation spectra and the reflection spectra (3.7–21 eV) measured at 7 K. On the basis of the obtained results three absorption peaks at 4.7, 5.8 and 6.5 eV were detected and assigned to charge-transfer absorption from O^2? to Fe³⁺ ions; the intrinsic PL band at 3.28 eV was revealed and attributed to radiative annihilation of self-trapped excitons, the defect luminescence bands at 2.68 and 3.54 eV were separated; the strong PL band at 1.72 eV was revealed and attributed to a radiative transition in Fe³⁺ ion.     

Absorption,luminescence, and electron paramagnetic resonance of molybdenum ions in CdWO4

A single crystal of cadmium tungstate (CdWO₄) containing approximately 200 ppm of molybdenum was grown by the Czochralski method and then characterized in a series of optical absorption, photoluminescence (PL), photoluminescence excitation (PLE), and electron paramagnetic resonance (EPR) experiments. The Mo⁶⁺ ions substitute for W⁶⁺ ions and serve as recombination sites for electrons and holes when the crystal is exposed to ionizing radiation. A charge-transfer absorption band for the Mo⁶⁺ ions was observed near 320 nm at 10 K. The PL experiments, performed at low temperature with 325 nm excitation, showed a Mo-associated emission peaking near 680 nm. A direct correlation of the 680 nm emission and the 320 nm absorption band was established by the PLE data. When these doped CdWO₄ crystals are exposed at low temperature either to light that is near or above the band gap or to X-rays, the Mo⁶⁺ ions can trap an electron and form stable Mo⁵⁺ ions. The EPR spectrum of the Mo⁵⁺ ions was observed at temperatures near 15 K, and a complete set of parameters describing the g matrix was obtained from an angular dependence study.     

Optical and electrical properties of Ge-implanted SiO2 layers on n-Si and p-Si

Ge ions of 100 keV were implanted into a 120 nm-thick SiO₂ layer on n-Si at room temperature while those of 80 keV were into the same SiO₂ layer on p-Si. Samples were, subsequently, annealed at 500°C for 2 h to effectively induce radiative defects in the SiO₂. Maximum intensities of sharp violet photoluminescence (PL) from the SiO₂/n-Si and the SiO₂/p-Si samples were observed when the samples have been implanted with doses of 1×10¹⁶ and 5×10¹⁵ cm⁻², respectively. According to current–voltage (I–V) characteristics, the defect-related samples exhibit large leakage currents with electroluminescence (EL) at only reverse bias region regardless of the type of substrate. Nanocrystal-related samples obtained by an annealing at 1100°C for 4 h show the leakage at both the reverse and the forward region.     

Low-temperature photoluminescence of II–VI films obtained by close-spaced vacuum sublimation

Low-temperature photoluminescence (PL) spectra of CdTe and ZnTe films obtained by a close-spaced volume sublimation technique under different technological conditions (substrate temperatures) were investigated. Analysis of the experimental results made it possible to conclude that the nature of the structure of the PL spectra observed experimentally is caused by the recombination of the excitons bound to shallow neutral acceptors, donor–acceptor pairs with the participation of the complex acceptors, and the presence of the extended defects like dislocations. The presence of neutral acceptors is related to the Li, Na, P or Cu residual impurities. As a result of the study of the PL spectra of CdTe and ZnTe films the optimal temperature conditions of their growth were determined as the substrate temperature T_s=623 K and 673 K, respectively.     

Raman studies of phase transitions in ferroelectric [C2H5NH3]2ZnCl4

The present paper accounted for the synthesis, differential scanning calorimetric and vibrational spectroscopy of [C₂H₅NH₃]₂ZnCl₄grown at room temperature. Differential scanning calorimetric (DSC) disclosed five phase transitions at T₁=231 K, T₂=234 K, T₃=237 K, T₄=247 K and T₅=312 K. The temperature dependence of the dielectric constant at different temperatures proved that this compound is ferroelectric below 238 K. Raman spectra as function temperature have been used to characterize these transitions and their nature, which indicates a change of the some peak near the transitions phase. The analysis of the wavenumber and the line width based on the order–disorder model allowed to obtain information relative to the thermal coefficient and the activation energy near the transitions phase.     

Emission of Cu-related complexes in ZnO:Cu nanocrystals

Photoluminescence (PL), its temperature dependence, scanning electronic microscopy (SEM) and X ray diffraction (XRD) have been applied for the comparative study of varying the emission, morphology and crystal structure of ZnO and ZnO:Cu nanocrystals (NCs) versus technological routines, as well as the dependence of ZnO:Cu NC parameters on the Cu concentration. A set of ZnO and ZnO Cu NCs was prepared by the electrochemical (anodization) method at a permanent voltage and different etching durations with follows thermal annealing at 400 °C for 2 h in ambient air. The size of ZnO NCs decreases from 300 nm×540 nm down to 200 nm×320 nm with etching duration increasing. XRD study has confirmed that thermal annealing stimulates the ZnO oxidation and crystallization with the formation of wurtzite ZnO crystal lattice. XRD method has been used for monitoring the lattice parameters and for confirming the Cu doping of ZnO Cu NCs. In ZnO Cu NCs four defect related PL bands are detected with the PL peaks at 1.95–2.00 eV (A), 2.15-2.23  eV (B), 2.43–2.50 eV (C) and 2.61–2.69 eV (D). Highest PL intensities of orange, yellow and green emissions have been obtained in ZnO Cu NCs with the Cu concentration of 2.28 at%. At Cu concentration increasing (≥2.28 at%) the PL intensities of the bands A, B, C decrease and the new PL band peaked at 2.61–2.69 eV at 10 K appears in the PL spectrum. The variation of PL intensities for all PL bands versus temperature has been studied and the corresponding activation energies of PL thermal decay have been estimated. The type of Cu-related complexes is discussed using the correlation between the PL spectrum transformation and the variation of XRD parameters in ZnO Cu NCs.     

Magnetism and transport properties of gamma-irradiated polymer-CrO2 composites

The transport properties of the gamma-irradiated CrO₂-polymer composites were investigated. The resistance R is strongly current I dependent, except at high temperature where it displays a semiconductor-like temperature dependence for all currents. At low currents, I≤10 μA, as the temperature decreases far below the ferromagnetic transition, the resistance decreases first, then reaches a minimum, and at last increases again toward a second peak. At even lower temperatures, the second peak is followed by a metallic-like temperature dependence of R that ends at a cusp point marking the metal–insulator transition. The increase of the current shifts the cusp toward lower temperatures and the first minima toward higher temperatures. The resistance increases with the increase in current for all currents in the range 0.2≤I≤10 μA. For I≥50 μA, the resistance increases monotonically with the decrease in temperature in the whole temperature range but obeys different laws at low and high temperatures. An explanation attempt in terms of spin transport, disorder, and thermal effects is proposed.     

Acceptors related to group I elements in ZnO ceramics

ZnO ceramics doped with Li, Na or K were sintered in air for 4 h at 1000 °C. Electrical conductivity as well as photoluminescence (PL), PL excitation and photoconductivity spectra were measured and compared with those in undoped samples. The influence of both fast and slow cooling of the samples from 1000 °C on measured characteristics was investigated. The yellow–orange PL bands associated with the deep acceptors Li_Zn, Na_Zn and K_Zn were observed and the corresponding PL excitation spectra were determined. These acceptors were found to form some complexes with other lattice defects.