Vacancy filling effect of graphene on photoluminescence behavior of ZnO/graphene nanocomposite

We report on the aerosol synthesis and optical characterization of ZnO/unoxidized graphene (UG) platelets nanocomposite films with high optical transparency (>85% at visible wavelengths). The ZnO/UG composite films, in which UG nanoplatelets are embedded in nano‐grained ZnO, were fabricated from colloidal suspensions of UG platelets with an aqueous zinc precursor. From photoluminescence (PL) spectra of the UG composite films, it was found that PL intensity decreases with the addition of UG platelets. The features of PL intensity in the UG composites are in contrast to that of ZnO/graphene oxide (G‐O) platelets composites, and can be explained by the absence of an oxygen vacancy filling effect, due to the unoxidized nature of UG and an increase in defect sites in its composites. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Facile Fabrication of Bicomponent CoO/CoFe2O4‐N‐Doped Graphene Hybrids with Ultrahigh Lithium Storage Capacity

A facile strategy is developed to fabricate bicomponent CoO/CoFe₂O₄‐N‐doped graphene hybrids (CoO/CoFe₂O₄‐NG). These hybrids are demonstrated to be potential high‐performance anodes for lithium‐ion batteries (LIBs). The CoO/CoFe₂O₄ nanoplatelets are finely dispersed on the surface of N‐doped graphene nanosheets (CoO/CoFe₂O₄‐NG). The CoO/CoFe₂O₄‐NG electrode exhibits ultrahigh specific capacity with 1172 mA h g^?1 at 500 mA g^?1 and 970 mA h g^?1 at 1000 mA g^?1 as well as excellent cycle stability due to the synergetic effects of N‐doped graphene and CoO/CoFe₂O₄ nanoplatelets. The well‐dispersed bicomponent CoO/CoFe₂O₄ is responsible for the high specific capacity. The N‐doped graphene with high specific surface area has dual roles: to provide active sites for dispersing the CoO/CoFe₂O₄ species and to function as an electrical conducting matrix for fast charge transfer. This method provides a simple and efficient way to configure the hybridized electrode materials with high lithium storage capacity.     

TeI4掺杂量对n型Bi2Te3基烧结材料热电性能的影响

采用区熔法结合放电等离子体快速烧结(SPS)技术制备了n型Bi₂Te₃基热电材料.在300—500K的温度范围内测量了各热电性能参数，包括电导率(σ)、塞贝克系数(α)和热导率(κ)，研究了掺杂剂TeI₄的含量(质量百分比分别为0，0.05，0.08，0.10，0.13和0.15wt%)对热电性能的影响.结果表明：试样的载流子浓度(n)随TeI₄含量增加而增大，使电导率增大、塞贝克系数的绝对值先增大而后减小，从而导致品质因子(α²σ)呈先增加后降低的变化趋势；同时，由于异质离子(I^-)以及载流子对声子的散射作用增强，可显著降低其晶格热导率.烧结材料的性能优值(ZT=α²σT/κ)对应于TeI₄含量为0.08wt%有其最大值，约为0.92.此外，烧结材料的抗弯强度增加至80MPa左右，从而可以显著改善材料的可加工性以及元器件的使用可靠性. 关键词： 2Te₃')" href="#">Bi₂Te₃ 放电等离子体快速烧结 热电性能     

Electrical and optical percolations in PMMA/GNP composite films

Effects of graphene nanoplatelet (GNP) addition on the electrical conductivity and optical absorbance of poly(methyl methacrylate)/graphene nanoplatelet (PMMA/GNP) composite films were studied. Optical absorbance and two point probe resistivity techniques were used to determine the variations of the optical and electrical properties of the composites, respectively. Absorbance intensity, A, and surface resistivity, R_s, of the composite films were monitored as a function of GNP mass fraction (M) at room temperature. Absorbance intensity values of the composites were increased and surface resistivity values were decreased by increasing the content of GNP in the composite. Electrical and optical percolation thresholds of composite films were determined as M_σ = 27.5 wt.% and M_op = 26.6 wt.%, respectively. The conductivity and the optical results were attributed to the classical and site percolation theories, respectively. Optical (β_op) and electrical (β_σ) critical exponents were calculated as 0.40 and 1.71, respectively.     

Preparation and electrochemical properties of LiFePO<Subscript>4</Subscript>/graphene composites from tailoring graphene oxides

LiFePO₄/graphene composites have been prepared by using tailoring graphene oxide (GO) nanosheets as precursors. The structure and electrochemical properties of the composites were investigated by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), Raman microscopy, and a variety of electrochemical testing techniques. The decrease in graphene size reduces the contact resistance between activated materials, and enhances the lithium-ion transport in LiFePO₄/graphene composites. With low weight fractions of small-size graphene sheets, the composites show better electrochemical performance than those with large size graphene sheets.     

High‐temperature thermoelectric properties of p‐type skutterudites Ybx Co3FeSb12

Partially filled polycrystalline p‐type skutterudites of nominal compositions Yb_x Co₃FeSb₁₂ were synthesized and their thermoelectric properties characterized. The compositions and filling fractions were confirmed with a combination of Rietveld refinement and elemental analysis. The thermoelectric properties were evaluated from 300 K to 810 K. The Seebeck coefficient and resistivity increase while the thermal conductivity decreases with increasing Yb content. A maximum ZT value of 0.85 was obtained at 810 K. This work is part of a continuing effort to enhance the thermoelectric properties of p‐type skutterudites, as this class of materials continues to be of interest for thermoelectrics applications. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and characterization of graphene nanoplatelet-La0.7Ca0.3MnO3 composites

ABSTRACT

La_0.7Ca_0.3MnO₃ perovskite and its composites with graphene nanoplatelet (GNP) were prepared using a wet chemical method. The structural, magnetic and magnetocaloric properties of La_0.7Ca_0.3MnO₃: GNP composites were investigated to determine the effect of GNPs. The results of XRD analysis show that the synthesised powders can be almost indexed to pure phase orthorhombic La_0.7Ca_0.3MnO_3. The magnetic measurements demonstrate that 0.7 and 1% GNP amounts cause an increase in the Curie temperature (T_C), and for larger amounts of GNP, the T_C monotonically decreases, except for the sample with 10% GNP. The results obtained from the Arrott plots show that the magnetic phase transition of the samples transforms from the first to second order with increasing GNP amount. The changes in the magnetocaloric properties are interpreted in terms of perovskite phase formations via structural analysis. The amounts of graphene nanoplatelets in the oxide powders are correlated with the observed magnetocaloric properties. The best magnetocaloric performance with the maximum magnetic entropy change of 3.99 Jkg^?1K^?1 and refrigeration capacity of 90 Jkg^?1 was obtained at a 2?T magnetic field.     

Tunable n‐ and p‐type doping of single‐layer graphene by engineering its interaction with the SiO2 support

We report a technique to tune the excess charge concentration in single‐layer graphene from p‐ to n‐type up to densities of |n | ～ 1.2 × 10¹³ cm^–2, corresponding to a displacement electric field of ～2.5 V/nm. The tuning is achieved by engineering the interaction between graphene and the underlying Si/SiO₂ substrate with an amino group‐terminated self‐assembled monolayer, and subsequent rinsing in aqueous solutions at controlled pH. Raman spectroscopy and electrical measurements on treated graphene devices confirm the occurrence of doping. Interestingly, we found the field‐effect mobility not to be significantly affected by the procedure. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Growth of FePO<Subscript>4</Subscript> nanoparticles on graphene oxide sheets for synthesis of LiFePO<Subscript>4</Subscript>/graphene

FePO₄·xH₂O/graphene oxide (FePO₄·xH₂O/GO) composites were prepared by a facile chemical precipitation method. Using the as-prepared FePO₄·xH₂O/GO and LiOH·H₂O as precursors and followed by carbothermal reduction, LiFePO₄/graphene composites were obtained. Scanning electron microscope (SEM) images indicated that the graphene had very good dispersity and uniformly attached to the LiFePO₄ particles. The conductive framework of graphene improved the electrochemical properties of the composites. The composites deliver high initial discharge capacity of 163.4 mAh g^?1 as well as outstanding rate performance.     

An alternative approach for optimal carrier concentration towards ideal thermoelectric performance

Optimization of the carrier concentration of any thermoelectric material is a prime factor for the enhancement of the thermoelectric figure of merit. An alternative approach for achieving optimal carrier concentration is presented here. We introduce impurity levels of ytterbium (Yb) near the valence band edge of Pb_1–xSn_x Te. The temperature‐dependent redistribution of electrons between the Yb‐impurity levels and the valence band is found to optimize the excess hole concentration at low temperature and negating the effect of intrinsic conduction at higher temperature leading to significantly improved thermoelectric performance in Pb_1–xSn_x Te. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Microwave-assisted rapid synthesis of Ag nanoparticles/graphene nanosheet composites and their application for hydrogen peroxide detection

Abstract  

Ag nanoparticles/graphene nanosheet (AgNPs/GN) composites have been rapidly prepared by a one-pot microwave-assisted reduction method, carried out by microwave irradiation of a N,N-dimethylformamide (DMF) solution of graphene oxide (GO) and AgNO₃. Several analytical techniques including UV–vis spectroscopy, FT-IR spectroscopy, Raman spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy (TEM) have been used to characterize the resulting AgNPs/GN composites. It suggests that such composites exhibit good catalytic activity toward reduction of hydrogen peroxide (H₂O₂), leading to a H₂O₂ sensor with a fast amperometric response time of less than 2 s. The linear detection range is estimated to be from 0.1 to 100 mM (r = 0.999), and the detection limit is estimated to be 0.5 μM at a signal-to-noise ratio of 3.     

DC conductivity and magnetic properties of piezoelectric–piezomagnetic composite system

A series of composites (1−x) (Ni_0.8Zn_0.2Fe₂O₄)+x (BaTiO₃), where x=0%, 20%, 40%, 60%, 80% and 100% BT content, have been prepared by the standard ceramic technique, then sintered at 1200 °C for 8 h. X-ray diffraction analysis shows that the prepared composites consist of two phases, ferrimagnetic and ferroelectric. DC electrical resistivity, thermoelectric power, charge carriers concentration and charge carrier mobility have been studied at different temperatures. It was found that the DC electrical conductivity increases with increasing BT content. The values of the thermoelectric power were positive and negative for the composites indicating that there are two conduction mechanisms, hopping and band conduction, respectively. Using the values of DC electrical conductivity and thermoelectric power, the values of charge carrier mobility and the charge carrier concentration were calculated. Magnetic measurements (hysteresis loop and magnetic permeability) show that the magnetization decreases by increasing BT content. M–H loop of pure Ni_0.6 Zn_0.4 Fe₂O₄ composite indicates that it is paramagnetic at room temperature and that the magnetization is diluted by increasing the BT content in the composite system. The value of magnetoelectric coefficient for the composites decreases by increasing BT content for all the compositions except for 40% BT content, which may be due to the low resistivity of magnetic phase compared with the BT phase that causes a leakage of induced charges on the piezoelectric phase. Since both ferroelectric and magnetic phases preserve their basic properties in the bulk composite, the present BT–NZF composite are potential candidates for applications as pollution sensors and electromagnetic waves.     

Nanostructured thermoelectric oxides with low thermal conductivity

Complex metal oxides, such as e.g. perovskite‐type phases are developed as potential functional materials to improve the efficiency of thermoelectric converters. Among those, cobaltates with p‐type conductivity and n‐type manganates are considered for the realisation of a ceramic thermoelectric converter. Sintered pellets with the composition AMO_3–δ (A = Ln, RE; M = Co, Mn, Ni, Ti) and “Ca₃Co₄O₉ derivates” were synthesized and characterised concerning their thermoelectric properties in a broad temperature range. It was found that the Seebeck coefficient and the electrical conductivity do not depend on the dimensions of the crystallites, while the heat conductivity can be substantially lowered by decreasing the size of the crystalline domains in these systems. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Overview of Hydroxyapatite–Graphene Nanoplatelets Composite as Bone Graft Substitute: Mechanical Behavior and In-vitro Biofunctionality

Hydroxyapatite (HA) and related materials have been frequently studied as ceramic-based bone graft materials due to their outstanding biocompatibility and osteoconduction. Since the bones are the load supporting parts of a vertebrate, they must have good fracture toughness (K_IC) to avoid fracture at high loading during limb movements. However, the main shortcomings of HA are the poor fracture toughness and brittleness. The mechanical properties of HA need to be improved for orthopedic applications, therefore it is often fabricated with other materials into a composite. This article focuses on the effect of carbon nanostructures (CNSs) especially graphene nanoplatelets (GNPs) on the mechanical, physicochemical properties and in-vitro bio-functional performances of HA. We provide an overview on the preparation and characterization of the HA–GNPs composites. To conclude, the challenges in the fabrication of multi-substituted HA–GNPs composites and future outlooks in the biomedical domain are discussed.     

Artificially controlled synthesis of graphene intramolecular heterojunctions for phonon engineering

Because phonons are the main carriers for graphene heat transfer, modifying the dynamic properties of the crystal lattice by isotopes modulates the phonon behavior and alters the thermal properties. Here we demonstrate an artificially controlled texture synthesis of ¹²C‐graphene/¹³C‐graphene heterostructures via chemical vapor deposition and an O₂ plasma etching. The electrical and thermal properties of the graphene across the heterojunction show that ¹²C‐graphene and ¹³C‐ graphene are electronically connected as resistors in series, while the thermal conductivity across the junction is dramatically reduced due to the suppressed phonon propagation, which causes the conductivity across the junction to be lower than that of graphene sheets with randomly mixed isotopes. These findings should help realize novel two‐dimensional graphene thermoelectric devices where phonon modulation controls the electrons and heat transport independently. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Low-temperature sintering and electromagnetic properties of Ba(Zn1/3Nb2/3)O3/NiCuZn ferrite composites

Dense Ba(Zn_1/3Nb_2/3)O₃/(Ni_0.37Cu_0.20Zn_0.43O)-(Fe₂O₃)_0.96 (BZN/NiCuZn) composites were prepared by the conventional solid-state reaction method and sintered at 950 °C. The phase composition and surface morphology of the composites were investigated using XRD and SEM, respectively. The dielectric and magnetic properties of the composites are also reported. In low frequency range the dielectric properties of the BZN/NiCuZn composites show Maxwell-Wagner relaxation. In high frequency range the BZN/NiCuZn composites possess high dielectric constants and permeabilities, which can be used in high-frequency communications for capacitor-inductor integrating devices such as electromagnetic interference filters and antennas.     

Phase transition and high temperature thermoelectric properties of copper selenide Cu2-x Se （0 ≤ x ≤ 0.25）

With good electrical properties and an inherently complex crystal structure, Cu_2-xSe is a potential “phonon glass electron crystal” thermoelectric material that has previously not attracted much interest. In this study, Cu_2-xSe (0 ≤ x ≤ 0.25) compounds were synthesized by a melting-quenching method, and then sintered by spark plasma sintering to obtain bulk material. The effect of Cu content on the phase transition and thermoelectric properties of Cu_2-xSe were investigated in the temperature range of 300 K—750 K. The results of X-ray diffraction at room temperature show that Cu_2-xSe compounds possess a cubic structure with a space group of Fm3m (#225) when 0.15 < x le 0.25, whereas they adopt a composite of monoclinic and cubic phases when 0 ≤ x ≤ 0.15. The thermoelectric property measurements show that with increasing Cu content, the electrical conductivity decreases, the Seebeck coefficient increases and the thermal conductivity decreases. Due to the relatively good power factor and low thermal conductivity, the nearly stoichiometric Cu₂Se compound achieves the highest ZT of 0.38 at 750 K. It is expected that the thermoelectric performance can be further optimized by doping appropriate elements and/or via a nanostructuring approach.     

Electrical,optical and mechanical properties of PS/GNP composite films

In this study, the electrical, optical and mechanical properties of polystyrene (PS) thin films added graphene nanoplatelet (GNP) have been investigated. Surface conductivity (σ), absorbance intensity (A) and tensile modulus of these composite films have increased with increasing the content of GNP in the composite. The increase in the electrical and optical properties of the PS/GNP composite films has been interpreted by site and classical percolation theory, respectively. The electrical and the optical percolation thresholds of PS/GNP composite films were determined as R_σ?=?23.0?wt.% and R_op?=?13.0?wt.%, respectively. While the conductivity results have been attributed to the classical percolation theory, the optical results have attributed to the site percolation theory. The electrical (β_σ) and the optical (β_op) critical exponents were calculated as 2.54 and 0.40, respectively. The tensile modulus and the tensile strength of the PS/GNP composites increased with the increasing of GNP content in the PS. But, the toughness of the composites fluctuated with GNP addition.     

One-step preparation of hierarchical superparamagnetic iron oxide/graphene composites via hydrothermal method

In this paper, graphene/magnetite composites with hierarchical Fe₃O₄ structures were synthesized via a one-step hydrothermal method. The size of Fe₃O₄ nanocrystals and nanocrystal clusters can easily be controlled by altering reaction time and the starting mixed solvent ratio, respectively. Raman measurements evidenced that graphene oxide was simultaneously reduced to graphene during the deposition of magnetite particles. The deposition of Fe₃O₄ nanocrystals and nanocrystal clusters impedes graphene to restore the graphite structure. The composites showed a high crystallinity of magnetite and a considerable saturation magnetization. Furthermore, the acrylate modified Fe₃O₄ makes the composites water-dispersible and can effectively load polyfluorene polyelectrolyte via electrostatic force. The high magnetism, excellent water dispersibility and strong photoluminescence make these composites ideal candidates for various important applications such as magnetic resonance imaging, bioseparation, bioimaging, and optical devices fabrication.     

Temperature dependence of the noise amplitude in graphene and graphene oxide

Graphene and related materials such as carbon nanotubes and graphene oxide are promising materials for future applications in chemical sensing and electronics. Electronic noise in these materials is typically very high due to the low number of carriers and the inverse dependence of 1/f noise on the number of carriers. We have investigated the changes in 1/f noise amplitude with temperature in exfoliated graphene and reduced graphene oxide devices. We show that using reduced graphene oxide results in an intriguing environmental coupling to noise amplitude. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)