Ultrasound biomicroscopy measurement of skin thickness change induced by cosmetic treatment with ultrasound stimulation

Moisturizing creams and lotions are commonly used in daily life for beauty and treatment of different skin conditions such as dryness and wrinkling, and ultrasound stimulation has been used to enhance the delivery of ingredients into skin. However, there is a lack of convenient methods to study the effect of ultrasound stimulation on lotion absorption by skin in vivo. Ultrasound biomicroscopy was adopted as a viable tool in this study to investigate the effectiveness of ultrasound stimulation on the enhancement of lotion delivery into skin. The forearm skin of 10 male and 10 female young subjects was tested at three different sites, including two lotion treatment sites with (Ultrasound Equipment – UE ON) and without (UE OFF) ultrasound stimulation and a control site without any lotion treatment. 1 MHz ultrasound with a duty cycle of 1.7%, a spatial peak temporal peak pressure of 195 kPa and an average power of 0.43 W was used for the stimulation. The skin thickness before, immediately after (0 min), and 15 and 30 min after the treatment was measured by an ultrasound biomicroscopic system (55 MHz). It was found that the skin thickness significantly increased immediately after the lotion treatment for both UE ON (from 1.379 ± 0.187 mm to 1.466 ± 0.182 mm, p < 0.001) and UE OFF (from 1.396 ± 0.193 mm to 1.430 ± 0.194 mm, p < 0.001) groups. Further comparison between the two groups revealed that the skin thickness increase of UE ON group was significantly larger than that of UE OFF group (6.5 ± 2.4% vs. 2.5 ± 1.3%, p < 0.001). Furthermore, it was disclosed that the enhancement of lotion delivery by ultrasound stimulation was more effective for the female subjects than the male subjects (7.6 ± 2.3% vs. 5.4 ± 2.0% immediately after treatment, p = 0.017). In conclusion, this study demonstrated that ultrasound biomicroscopy was a feasible method for studying the effectiveness of lotion treatment in vivo, and ultrasound stimulation was effective to enhance the rate of lotion absorption into skin.     

Impact of thermal effects induced by ultrasound on viability of rat C6 glioma cells

In order to have consistent and repeatable effects of sonodynamic therapy (SDT) on various cancer cells or tissue lesions we should be able to control a delivered ultrasound energy and thermal effects induced. The objective of this study was to investigate viability of rat C6 glioma cells in vitro depending on the intensity of ultrasound in the region of cells and to determine the exposure time inducing temperature rise above 43 °C, which is known to be toxic for cells. For measurements a planar piezoelectric transducer with a diameter of 20 mm and a resonance frequency of 1.06 MHz was used. The transducer generated tone bursts with 94 μs duration, 0.4 duty-cycle and initial intensity I_SATA (spatial averaged, temporal averaged) varied from 0.33 W/cm² to 8 W/cm² (average acoustic power varied from 1 W to 24 W). The rat C6 glioma cells were cultured on a bottom of wells in 12-well plates, incubated for 24 h and then exposed to ultrasound with measured acoustic properties, inducing or causing no thermal effects leading to cell death. Cell viability rate was determined by MTT assay (a standard colorimetric assay for assessing cell viability) as the ratio of the optical densities of the group treated by ultrasound to the control group. Structural cellular changes and apoptosis estimation were observed under a microscope. Quantitative analysis of the obtained results allowed to determine the maximal exposure time that does not lead to the thermal effects above 43 °C in the region of cells for each initial intensity of the tone bursts used as well as the threshold intensity causing cell death after 3 min exposure to ultrasound due to thermal effects. The averaged threshold intensity was found to be about 5.7 W/cm².     

The impact of ultrasound and steam blanching pre-treatments on the drying kinetics,energy consumption and selected properties of parsley leaves

In current study the influence of ultrasound pre-treatment and drying conditions (microwave power, air temperature) was analysed by the means of drying kinetics, energy consumption and selected quality properties of dried parsley leaves. Ultrasound treatment (US) was compared with conventional treatment – steam blanching. In comparison to untreated material, ultrasound applied at 21 kHz, 12 W/g, contributed to significant reduction of the drying time up to 29.8%. Moreover, the energy expenditures were reduced maximally by 33.6% for parsley dried at 30 °C and 300 W. For this sample the colour retention was the highest, as well. In turn, steam treated parsley was dried maximally by 28.9% faster and thus specific energy consumption decreased to 72.0% of the value for intact leaves when 20 °C and 300 W were set. The influence of pre-drying treatment on the quality properties depended on the drying conditions. Pre-drying treatment (US, blanching) did not affect the lutein content significantly, whereas the most considerable increase of chlorophyll a and b resistance and their relative concentration (Chl a/b ratio) was achieved in US-treated leaves dried at 30 °C and 100 W. The utilisation of drying pre-treatment and dehydration parameters should be considered with respect to further utilisation of dried parsley leaves. Nonetheless, sonication is worth to be taken into account due to a significant reduction of energy expenditures and an improvement of resistance of bioactive components.     

Application of ultrasound as pretreatment for extraction of podophyllotoxin from rhizomes of Podophyllum peltatum

The effect of high-power ultrasound pretreatment on the extraction of podophyllotoxin from Podophyllum peltatum was investigated. Direct sonication by an ultrasound probe horn was applied at 24 kHz and a number of factors were investigated: particle size (0.18-0.6 mm), type of solvent (0-100% aqueous ethanol), ultrasonic treatment time (2-40 min), and power of ultrasound (0-100% power intensity, maximum power: 78 W). The optimal condition of ultrasound was achieved with 0.425-0.6 mm particle size, 10 min sonication time, 35 W ultrasound power, and water as the medium. There was no obvious degradation of podophyllotoxin with ultrasound under the applied conditions, and an improvement in extractability was observed. The SEM microscopic structure change of treated samples disclosed the effect of ultrasound on the tissue cells. The increased pore volume and surface area after ultrasonic treatment also confirmed the positive effect of ultrasound pretreatment on the extraction yield of podophyllotoxin from the plant cells.     

Electrical properties and dielectric relaxation of thermally evaporated zinc phthalocyanine thin films

The electrical transport properties and dielectric relaxation of Au/zinc phthalocyanine, ZnPC/Au devices have been investigated. The DC thermal activation energy at temperature region 400-500 K is 0.78 eV. The dominant conduction mechanisms in the device are ohmic conduction below 1 V and space charge limited conduction dominated by exponential trap distribution in potentials >1 V. Some parameters, such as concentration of thermally generated holes in valence band, the trap concentration per unit energy range at the valence band edge, the total concentration of traps and the temperature parameter characterizing the exponential trap distribution and their relation with temperatures have been determined. The AC electrical conductivity, σ_ac, as a function of temperature and frequency has been investigated. It showed a frequency and temperature dependence of AC conductivity for films in the temperature range 300-400 K. The films conductivity in the temperature range 400-435 K increased with increasing temperature and it shows no response for frequency change. The dominant conduction mechanism is the correlated barrier hopping. The temperature and frequency dependence of real and imaginary dielectric constants and loss tangent were investigated.     

Valence band and surface core-level shift studies of the oxygen-induced p(3 × 1) reconstruction of the W(1 0 0) surface

Using synchrotron radiation, W 4f_7/2 and valence-band (VB) photoelectron spectroscopy was used to study the oxidation states of the p(3 × 1) reconstructed surface of W(1 0 0) produced by oxygen adsorption at 1500 K. The W 4f_7/2 study showed two features at 0.40 and 1.50 eV higher binding energies relative to the bulk feature which represent shifts to lower binding energies compared to the W 4f_7/2 features of the as-grown oxygen films on W(1 0 0). Co-existence of these features is a characteristic of the formation of the p(3 × 1) structure. The VB studies of this system and as-grown oxygen films at room temperature (RT) showed an oxygen-induced feature for the p(3 × 1) structure for which the peak maximum had shifted by 0.9 eV to higher binding energies compared to the as-grown films. The direction of shifts in the W 4f_7/2 and VB spectra for the p(3 × 1) structure confirmed the reduction of the charge transfer from W to oxygen compared to the as-grown films. A study of the VB changes with photon energy shows that the main component of the oxygen-induced feature in the p(3 × 1) VB at 6.6 ± 0.2 eV is related to a hybridized state between W 5d and O 2p electrons.     

Ultrasound treatment enhances cholesterol removal ability of lactobacilli

This study aimed to evaluate the effect of ultrasound treatment on the cholesterol removing ability of lactobacilli. Viability of lactobacilli cells was significantly increased (P < 0.05) immediately after treatment, but higher intensity of 100 W and longer duration of 3 min was detrimental on cellular viability (P < 0.05). This was attributed to the disruption of membrane lipid bilayer, cell lysis and membrane lipid peroxidation upon ultrasound treatment at higher intensity and duration. Nevertheless, the effect of ultrasound on membrane properties was reversible, as the viability of ultrasound-treated lactobacilli was increased (P < 0.05) after fermentation at 37 °C for 20 h. The removal of cholesterol by ultrasound-treated lactobacilli via assimilation and incorporation of cholesterol into the cellular membrane also increased significantly (P < 0.05) upon treatment, as observed from the increased ratio of membrane C:P. Results from fluorescence anisotropies showed that most of the incorporated cholesterol was saturated in the regions of phospholipids tails, upper phospholipids, and polar heads of the membrane bilayer.     

Dynamic study of W atoms and clusters on W (1 1 1) surfaces

Using a field ion microscope, the diffusion behaviors and atomic processes of W atoms and clusters on W (1 1 1) surfaces were observed directly. The activation energy of W clusters diffusion on W (1 1 1) as a function of cluster size has an oscillatory and increasing behavior. But, the activation energy of a single W atom is especially high. The compact geometric structures are more stable and have higher activation energies of surface diffusion than structures with extra atoms at the periphery. Besides the terrace diffusion, other atomic processes such as the ascending, descending, detachment motion on W (1 1 1) surfaces were also observed. Unlike the general systems, their occurrence temperatures are quite near. These experimental results were used to discuss the formation mechanism of single atom W tips.     

Electron stimulated desorption of cesium atoms from germanium-covered tungsten

The electron stimulated desorption (ESD) yield and energy distributions for Cs atoms from cesium layers adsorbed on germanium-covered tungsten have been measured for different Ge film thicknesses, 0.25-4.75 ML (monolayer), as a function of electron energy and cesium coverage Θ. The measurements have been carried out using a time-of-flight method and surface ionization detector. In the majority of measurements Cs is adsorbed at 300 K. The appearance threshold for Cs atoms is about 30 eV, which correlates well with the Ge 3d ionization energy. As the electron energy increases the Cs atom ESD yield passes through a wide maximum at an electron energy of about 120 eV. In the Ge film thickness range from 0.5 to 2 ML, resonant Cs atom yield peaks are observed at electron energies of 50 and 80 eV that can be associated with W 5p and W 5s level excitations. As the cesium coverage increases the Cs atom yield passes through a smooth maximum at 1 ML coverage. The Cs atom ESD energy distributions are bell-shaped; they shift toward higher energies with increasing cesium coverage for thin germanium films and shift toward lower energies with increasing cesium coverage for thick germanium films. The energy distributions for ESD of Cs from a 1 ML Ge film exhibit a strong temperature dependence; at T = 160 K they consist of two bell-shaped curves: a narrow peak with a maximum at a kinetic energy of 0.35 eV and a wider peak with a maximum at a kinetic energy of 0.5 eV. The former is associated with W level excitations and the latter with a Ge 3d level excitation. These results can be interpreted in terms of the Auger stimulated desorption model.     

Fermentation of rice hull by Aspergillus japonicus under ultrasonic pretreatment

The application of ultrasound for treating rice hull used as the fermentation substrate for xylooligosaccharides production was investigated. Aspergillus japonicus CY6-1 was selected to produce cellulolytic and xylanolytic enzymes from untreated rice hull (RH) and rice hull treated with ultrasound (USRH-M). The hemicellulose yield was increased to 1.4-fold with ultrasound, and treatment time was greatly shortened from 24 h to 1.5 h at 80 °C and 300 W/28 kHz. The morphology of RH from various pretreatments was observed with field emission scanning electron microscope (FESEM), revealing the surface structure of USRH-M smoother than that of RH. USRH-M was much easier to be utilized by fungi, to extend the stability of enzyme activity and to increase activities of CMCase, β-glucosidase, and xylanase compared with those of untreated RH. The final fermentative products were xylotetraose, xylohexaose, and higher molecular weight xylooligosaccharides, achieving xylohexaose yield for USRH-M 80% higher than that for RH group.     

Energy analysis during acoustic bubble oscillations: Relationship between bubble energy and sonochemical parameters

In this work, energy analysis of an oscillating isolated spherical bubble in water irradiated by an ultrasonic wave has been theoretically studied for various conditions of acoustic amplitude, ultrasound frequency, static pressure and liquid temperature in order to explain the effects of these key parameters on both sonochemistry and sonoluminescence. The Keller–Miksis equation for the temporal variation of the bubble radius in compressible and viscous medium has been employed as a dynamics model. The numerical calculations showed that the rate of energy accumulation, dE/dt, increased linearly with increasing acoustic amplitude in the range of 1.5–3.0 atm and decreased sharply with increasing frequency in the range 200–1000 kHz. There exists an optimal static pressure at which the power w is highest. This optimum shifts toward a higher value as the acoustic amplitude increases. The energy of the bubble slightly increases with the increase in liquid temperature from 10 to 60 °C. The results of this study should be a helpful means to explain a variety of experimental observations conducted in the field of sonochemistry and sonoluminescence concerning the effects of operational parameters.     

Ultrasound induces cellular destruction of nasopharyngeal carcinoma cells in the presence of curcumin

Objectives

Curcumin, a natural pigment from the traditional Chinese herb, has shown promise as an efficient enhancer of ultrasound. The present study aims to investigate ultrasound-induced cellular destruction of nasopharyngeal carcinoma cells in the presence of curcumin in vitro.

Methods

Nasopharyngeal carcinoma cell line CNE2 cells were incubated by 10 μm curcumin and then were treated by ultrasound for 8 s at the intensity of 0.46 W/cm². Cytotoxicity was evaluated using MTT assay and light microscopy. Mitochondrial damage was analyzed using a confocal laser scanning microcopy with Rhodamine 123 and ultrastructural changes were observed using a transmission electron microscopy (TEM).

Results

MTT assay showed that cytotoxicity induced by ultrasound treatment alone and curcumin treatment alone was 18.16 ± 2.37% and 24.93 ± 8.30%, respectively. The cytotoxicity induced by the combined treatment of ultrasound and curcumin significantly increased up to 86.67 ± 7.78%. TEM showed that microvillin disappearance, membrane blebbing, chromatin condensation, swollen mitochondria, and mitochondrial myelin-like body were observed in the cells treated by ultrasound and curcumin together. The significant collapse of mitochondrial membrane potential (MMP) was markedly observed in the CNE2 cells after the combined treatment of curcumin and ultrasound.

Conclusions

Our findings demonstrated that ultrasound sonication in the presence of curcumin significantly killed the CNE2 cells and induced ultrastructural damage and the dysfunction of mitochondria, suggesting that ultrasound treatment remarkably induced cellular destruction of nasopharyngeal carcinoma cells in the presence of curcumin.     

A study of core and valence levels in β-PbO2 by hard X-ray photoemission

The core and valence levels of β-PbO₂ have been studied using hard X-ray photoemission spectroscopy (hν = 6000 eV and 7700 eV). The Pb 4f core levels display an asymmetric lineshape which may be fitted with components associated with screened and unscreened final states. It is found that intrinsic final state screening is suppressed in the near-surface region. A shift in the O 1s binding energy due to recoil effects is observed under excitation at 7700 eV. It is shown that conduction band states have substantial 6s character and are selectively enhanced in hard X-ray photoemission spectra. However, the maximum amplitude in the Pb 6s partial density of states is found at the bottom of the valence band and the associated photoemission peak shows the most pronounced enhancement in intensity at high photon energy.     

Instant magnetic labeling of tumor cells by ultrasound in vitro

Magnetic labeling of living cells creates opportunities for numerous biomedical applications. Here we describe an instantly cell magnetic labeling method based on ultrasound. We present a detailed study on the ultrasound performance of a simple and efficient labeling protocol for H-22 cells in vitro. High frequency focus ultrasound was investigated as an alternative method to achieve instant cell labeling with the magnetic particles without the need for adjunct agents or initiating cell cultures. Mean diameter of 168 nm dextran-T40 coated superparamagnetic iron oxide (SPIO) nanoparticles were prepared by means of classical coprecipitation in solution in our laboratory. H-22 tumor cells suspended in phosphate-buffered saline (PBS, pH=7.2) were exposed to ultrasound at 1.37 MHz for up to 120 s in the presence of SPIOs. The cellular uptake of iron oxide nanoparticles was detected by prussion blue staining. The viability of cells was determined by a trypan blue exclusion test. At 2 W power and 60 s ultrasound exposure in presence of 410 μg/ml SPIOs, H-22 cell labeling efficiency reached 69.4±6.3% and the labeled cells exhibited an iron content of 10.38±2.43 pg per cell. Furthermore, 95.2±3.2% cells remained viable. The results indicated that the ultrasound protocol could be potentially applied to label cells with large-sized magnetic particles. We also calculated the shear stress at the 2 W power and 1.37 MHz used in experiments. The results showed that the shear stress threshold for ultrasonically induced H-22 cell reparable sonoporation was 697 Pa. These findings provide a quantitative guidance in designing ultrasound protocols for cell labeling.     

Effects of electron irradiation on the properties of GZO films deposited with RF magnetron sputtering

Transparent conductive GZO films were deposited on polycarbonate substrates by electron beam assisted radio frequency (RF) magnetron sputtering and then the influence of electron irradiation on the structural, optical and electrical properties of GZO films was investigated by using X-ray diffractometry, UV-vis spectrophotometry, four point probes, atomic force microscopy and UV photoelectron spectroscopy. Sputtering power was kept constant at 3 W/cm² during deposition, while electron irradiation energy varied from 450 to 900 eV.Electron irradiated GZO films show larger grain sizes than those of films prepared without electron irradiation, and films irradiated at 900 eV show higher optical transmittance in the visible wavelength region and lower sheet resistance (120 Ω/□) than other films. The work-function is also increased with electron irradiation energy. The highest work-function of 4.4 eV was observed in films that were electron irradiated at 900 eV.     

Kinetics of ultrasound-assisted lipase-catalyzed glycerolysis of olive oil in solvent-free system

This work reports experimental kinetic data of solvent-free glycerolysis of olive oil using a commercial immobilized lipase (Novozym 435) under the influence of ultrasound irradiation. The experiments were performed in a mechanically stirred reactor under ultrasound irradiation, evaluating the effects of temperature (50-70 °C), enzyme concentration (2.5-10 wt%) and glycerol to oil molar ratio (0.8:1-3:1). Results show that ultrasound-assisted lipase-catalyzed glycerolysis might be a potential alternative route to conventional methods, as high contents of reaction products, especially monoglycerides, were achieved at mild irradiation power supply (∼130 W) and temperature, in a relatively short reaction time (2 h) and low enzyme content (7.5 wt%). To completeness, two simplified kinetic modeling approaches, based on the ordered-sequential bi bi mechanism and reaction stoichiometry, were employed to represent the experimental data, thus allowing a better understanding of the reaction kinetics.     

A preliminary in vitro assessment of polymer-shelled microbubbles in contrast-enhanced ultrasound imaging

This paper focuses on the use of poly (vinyl alcohol)-shelled microbubbles as a contrast agent in ultrasound medical imaging. The objective was an in vitro assessment of the different working conditions and signal processing methods for the visual detection (especially in small vessels) of such microbubbles, while avoiding their destruction. Polymer-shelled microbubbles have recently been proposed as ultrasound contrast agents with some important advantages. The major drawback is a shell that is less elastic than that of the traditional lipidic microbubbles. Weaker echoes are expected, and their detection at low concentrations may be critical. In vitro experiments were performed with a commercial ultrasound scanner equipped with a dedicated acquisition board. A concentration of 100 bubbles/mm³, excitation pressure amplitudes from 120 kPa to 320 kPa, and a central frequency of 3 MHz or 4.5 MHz were used. Three multi-pulse techniques (i.e., pulse inversion, contrast pulse sequence based on three transmitted signals, and contrast pulse sequence in combination with the chirp pulse) were compared. The results confirmed that these microbubbles produce a weaker ultrasound response than lipidic bubbles with a reduced second-order nonlinear component. Nevertheless, these microbubbles can be detected by the contrast pulse sequence technique, especially when the chirp pulse is adopted. The best value of the contrast-to-tissue ratio was obtained at an excitation pressure amplitude of 230 kPa: although this pressure amplitude is higher than what is typically used for lipidic microbubbles, it does not cause the rupture of the polymeric contrast agent.     

A theoretical study of hydrogen adsorption and diffusion on a W(1 1 0) surface

We have used density functional theory to investigate hydrogen adsorption and diffusion on a W(1 1 0) surface. Hydrogen adsorption structures were examined from low coverage to one monolayer, and a threefold hollow site was found to be the most stable site at all coverages. In contrast to previous assertions, the work function decrease is not due to electron transfer from the hydrogen atoms to the W surface, but due to electron depletion at the vacuum region above the hydrogen atoms. Hydrogen atoms can diffuse via short-bridge sites and long-bridge sites at a coverage of θ = 1.0. Although the calculated activation energy for hydrogen diffusion via a short-bridge site is as small as 0.05 eV, field emission microscope experiments have shown that the activation energy for hydrogen diffusion is about 0.20 eV, which agrees fairly well with our calculated value of the activation energy via a long-bridge site. This discrepancy can be related to hydrogen delocalization on the W(1 1 0) surface, which has been suggested by electron energy loss spectroscopy experiments.     

The influence of optical bleaching on lifetimes and luminescence intensity in the slow component of optically stimulated luminescence of natural quartz from Nigeria

The intensity of optically stimulated luminescence may be decreased to a slow or medium component of its decay curve by optical bleaching, that is, by prolonged exposure of the luminescent sample to stimulating light. In this paper, we report on the influence of irradiation and measurement temperature on luminescence lifetimes as well as on the effect of measurement temperature on luminescence intensity in annealed natural quartz from Nigeria. Measurements were carried out in the slow component region using time-resolved optical stimulation at 470 nm on samples annealed at 500 and 600 °C. Luminescence lifetimes were determined from the resultant time-resolved luminescence spectra by analysing the portion of each spectrum after the stimulating light pulse of duration 11 μs. In preparatory tests, the influence of the duration of optical bleaching on lifetimes was investigated. It was found that lifetimes in samples annealed at 500 °C are independent of the duration of optical bleaching, whereas lifetimes in quartz annealed at 600 °C are affected, decreasing towards a constant value with duration of bleaching. Concerning measurements in the slow-component region, lifetimes were found to decrease with irradiation dose for samples annealed at either 500 or 600 °C. The temperature dependence of lifetimes in both sets of quartz is similar with lifetimes constant at about 36 μs between 20 and 120 °C, but decreasing consistently from then on to about 5 μs at 200 °C, the maximum measurement temperature used in experiments. The luminescence intensity was observed to typically go through a peak as the stimulation temperature was increased from 20 to 200 °C, following a brief initial decrease, a change better exemplified in the quartz annealed at 600 °C. The initial decrease in luminescence intensity is attributed to the dominance of optical stimulation over thermal stimulation. On the other hand, the subsequent change of luminescence intensity with temperature is discussed as evidence of thermal assistance to optical stimulation, initially with activation energy of 0.27±0.07 eV and of thermal quenching subsequently with activation energy equal to 0.93±0.23 eV for samples annealed at either 500 or 600 °C. The temperature dependence of lifetimes is explained as showing increased thermal effect on lifetimes with activation energy values within 0.83±0.01 eV. On the other hand, the influence of irradiation on lifetimes is accounted for in terms of an energy band model for quartz consisting of three luminescence centres and one non-radiative recombination centre.     

Diffusion and desorption of submonolayer platinum deposited on the multi-faceted surface of a tungsten micro-crystal

Diffusion and desorption of platinum on the tungsten micro-crystal in the form of the W(1 1 1) oriented emitter tip has been studied using the field electron microscopy (FEM) technique. Diffusion of small dose of platinum (average thickness about 0.18 geometrical ML after spreading) on the thermally clean W emitter tip was studied at temperatures 648-742 K. Average activation energy for diffusion E_diff was found to lie between 1.16 ± 0.08 eVand 1.30 ± 0.16 eV. During annealing at the diffusion temperatures Pt-induced faceting of the emitter surface was visible in the neighbourhood of the {1 1 1} pole. The layer equilibrated in the diffusion process was stable at temperatures up to 1100 K where reduction of the high voltage at a fixed emission current, characteristic of alloying of Pt with W, was detected. Submonolayer of platinum (Θ_Pt = 0.18 ML) started to desorb at tip temperature ≥1780 K. The measurements of average activation energy for desorption of ‘zero coverage’ Pt (0.03 ML ≤ Θ_Pt ≤ 0.06 ML) from the entire W emitter surface were carried out at temperatures 1990-2170 K and yield the value of E_des = 5.19 ± 0.22 eV to 5.33 ± 0.19 eV. The results are compared with data for diffusion of individual Pt atoms and small clusters and with data for adsorption of Pt atoms on a planar W(1 1 0) surface. In discussion the atomic surface structure of the substrate, modified by the strong interaction of Pt with the W micro-crystal, is also taken into account.