时间延迟型声表面波无源传感器的无线访问

介绍了一种基于无源声表面波（ＳＡＷ）器件的无线传感器．作为敏感器件的 ＳＡＷ器件由作为换能器的 ＩＤ－Ｔａｇ和一组反射栅组成．由访问系统发射出的电磁波通过 ＩＤ－Ｔａｇ在 ＳＡＷ器件上激励起声表面波,此声表面波在器件表面传播,被ＳＡＷ器件本身状态参数调制后,反射回波再通过ＩＤ－Ｔａｇ转变成电磁波向空间发射．因此对访问系统接收到的回波信号进行分析即可得到被测量。即实现了无线传感．由于以ＳＡＷ器件为敏感元件可以研制各种各样的物理量、化学量传感器,这种无线访问传感系统可在各种场合得到应用．     

利用准谐频叉指换能器实现GHz高频SAW滤波器

本文利用准谐频设计方法,在常规光刻工艺水平上,成功地实现了ＧＨＺ级声表面波（ＳＡＷ）器件,准谐频叉指换能器（ＱＨＩＤＴ）的优点为：其指条宽与指间隙可以比一般的单指换能器宽,克服了单指换能器内指间的多次反射,并且又较好地解决了普通谐频叉指换能器基频抑制不好的缺点,本文给出了制作在ＳＴ石英基片上,工作频率１１２８ＭＨＺ的声表面波滤波器的实验结果。     

高功率梯度折射率分别限制异质结构InGaAs/AlGaAs应变双量子阱激光器

采用金属有机化合物气相淀积（ Ｍ Ｏ Ｃ Ｖ Ｄ）方法成功地研制了具有两对梯度折射率（ Ｇ Ｒ Ｉ Ｎ）异质结结构的 Ｉｎ Ｇａ Ａｓ／ Ａｌ Ｇａ Ａｓ 应变双量子阱激光器。该激光器的波长为 ９７０～９８２ ｎｍ ,室温连续工作阈值电流密度为１４０ Ａ／ｃｍ ２, 工作在０．９ Ａ 时单面连续输出光功率为５２０ ｍ Ｗ , 工作在２．０ Ａ 时, 连续输出光功率为 １．４９ Ｗ , 最高功率可达 ２．４ Ｗ 。微分量子效率高达０．８３ Ｗ ／ Ａ。     

具有旋涡的翼型绕流辐射声场的数值研究

本文运用面无法和涡声理论数值来研究具有旋涡的ＮＡＳＡＧＡ（Ｗ）－１型翼型绕流的流场和辐射声场，这对于提高透平机械的效率及降低辐射噪声很有帮助。采用作者积累的关于面无法的一些计算技巧，首先成功地求解了不同攻角来流时的流场，再用涡声理论计算了涡旋绕过翼型时声压场的变化及声源的指向性，最后给出了有关这种流动噪声的发声机理和声源特性的一些有用的结论。     

高功率梯度折射率分别限制异质结构InGaAs／AlGaAs应变双量子阱？…

采用金属有机化合物气相淀积（ＭＯＣＶＤ）方法成功地研制了具有两对梯度折射率（ＧＲＩＮ）异质结构的ＩｎＧａＡｓ／ＡｌＧａＡｓ应变双量子阱激光器。该器的波长为９７０－９８２ｎｍ,室温连续工作阈值电流密度为１４０Ａ／ｃｍ＾２,工作在０．９Ａ时单面连续输出光功率为５２０ｍＷ,工作在２．０时,连续输出光功率为１．４９Ｗ,最高功率可达２．４Ｗ,微分量子效率高达０．８３Ｗ／Ａ。     

基于远距离激光测振仪的痕量危险品探测

光声/光热光谱技术已经广泛应用于痕量危险化学品和爆炸物的探测,并显示出高效的探测能力。然而,该技术通常需要在光声池中进行分析,并使用高灵敏度麦克风或压电传感器记录振动信号,因此不适用于在安全距离外的开放环境中探测泄漏的危险物质或爆炸物。为此,利用强度调制的量子级联激光器（QCL）激发微量固体（聚四氟乙烯）和气体（丙酮）的光声效应,借助自主研发的远距离激光多普勒测振仪（LDV）对QCL产生的光振动信号进行检测。通过扫描QCL的波长,测量振动信号的幅值并获取光声光谱,其结果与傅里叶变换红外光谱的结果高度一致。实验结果表明,自制的远距离LDV可以在距离达200 m的开放环境下有效地检测痕量固态和气态化学品的光声信号。     

声表面波生物传感器质量灵敏度的理论与实验验证

针对声表面波传感器在生物检测中的性能评价与优化,提出一种快捷验证适用于生物传感器的声表面波器件质量负载灵敏度的实时检测方法.首先基于二维近似假设和周期性边界条件,建立了以石英为压电基底材料、SiO2为波导层的Love波传感器的三维有限元分析模型,从理论上验证了波导层对Love波传感器灵敏度的影响.在实验上,通过MEMS...     

用埋入式光纤传感器探测建筑结构中的声发射

声发射技术已经应用于金属和混凝土结构中,作为探测内部裂缝的一种无损检测方法。目前用的技术都是由压电换能器来采集声发射信号。讨论了基于用光纤技术的声发射传感器的开发和测量方法。它是用埋入式光纤传感器来监测类似桥梁、高速公路、隧道和房屋建筑等混凝土结构中的开裂信号。     

尘埃等离子体中朗缪尔波的非线性调制

研究了尘埃等离子体中尘埃声波（ＤＡＷ）和尘埃离子声波（ＤＩＡＷ）对朗缪尔波的非线性调制。在小而有限振幅极限下,得到了朗缪尔波的包络孤立子。对于朗缪尔波与尘埃声波的非线性耦合,包络孤立子存在两个速度传播区;而对于与尘埃离子声波的耦合,只有一个传播区     

高灵敏度液体光声传感器的研制

光声光谱分析技术中,高灵敏度的光声传感器仍是其仪器装置的关键所在。不少研究者对此予以极大的重视。本文从理论上分析了液体光声波的传输特性、能量耦合原理。采用复合波导层方式,用国产压电陶瓷设计研制出两种不同结构的液体光声传感器。经实验测定,具有灵敏度高、抗干扰性强和使用方便等特点;适用于液体光声信号检测,尤其是在高低温、     

红外目标仿真光学机构

论述了目标仿真机构的用途、仿真的光学原理以及实现原理的光学系统。对其中的两个光学问题的研究作了详细地论述 ,即干扰光路 2倍于目标光路的视场角以及如何由摆镜的摆动实现。由于析光镜与光轴成 45°角 ,使像点在子午方向被拉长约为弧矢方向的 10倍。为了减少子午像差 ,将两块析光镜作成略带楔角的楔形镜。结果表明 ,由于该机构的尾焰、尾喷管用的是同一条光路 ,所以使结构大为简化 ,这对降低转动惯量非常有利 ;由于有干扰弹仿真 ,使机构的功能得到了扩大     

Black Holes Are One-Dimensional

The holographic principle has revealed that phyical systems in 3-D space, black holes included, are basically two-dimensional as far as their information content is concerned. This conclusion is complemented by one sketched here: as far as entropy or information flow is concerned, a black hole behaves as a one-dimensional channel. We define a channel in flat spacetime in thermodynamic terms, and contrast it with common entropy emitting systems. A black hole is more like the former: its entropy output is related to the emitted power as it would be for a one-dimensional channel, and disposal of an information stream down a black hole is limited by the power invested in the same way as for a one-dimensional channel.     

激光测距仪信噪比与激光发散角最佳值的选取

研讨激光测距仪的信噪比和激光发散角如何选取最佳值的问题。如果信噪比为SNR，激光发散角为θt，则取SNR θt^2最小时的信噪比和激光发散角为最佳值。     

Thermal modelling of laser welding and related processes: a literature review

The main emphasis of this review is on thermal modelling and prediction of laser welding in metals. However as similar techniques are employed to model conventional welding processes such as arc, resistance and friction, as well as related processes such as alloying, cladding and surface hardening, part of this review is given over to the modelling of these processes where appropriate. The time frame of the review is up to the year 2002.     

ZnS衬底上GeC/GaP增透保护膜系的制备及红外光学性质

把GeC/GaP双层膜用作ZnS衬底的长波红外(8~11.5μm波段)增透保护膜系。采用射频磁控溅射法,以高纯Ar为工作气体、单晶GaP圆片为靶制备了GaP薄膜;用射频磁控反应溅射法在高纯Ar和CH4的混合气体中,以单晶Ge圆片为靶制备了GeC薄膜。分别用柯西(Cauchy)公式和乌尔巴赫(Urbach)公式表示折射率和吸收系数,对薄膜的红外透射率曲线进行最小二乘法拟合,得到了它们的厚度及折射率、吸收系数等光学常数。GaP膜的折射率与块体材料的相近,在波长10μm处约为2.9;GeC膜的折射率较小,在波长10μm处约为1.78。用所得到的薄膜折射率,通过计算机膜系自动设计软件在ZnS衬底上设计并制备出了GeC/GaP双层增透保护膜系,当GaP膜厚较大时,由于吸收增大膜系增透效果较差;当GaP膜厚较小时,膜系有较好的增透效果。     

Raman Spectroscopy of Natural Bone and Synthetic Apatites

Abstract

Raman spectroscopy of natural bones and hydroxyapatites is described. In addition, how Raman spectroscopy has proved crucial in providing baseline data for the modification of synthetic apatite powders that are routinely used now as bone replacement materials is explained. It is important to understand the chemical structural properties of natural bone. Bone consists of two primary components: an inorganic or mineral phase, which is mainly a carbonated form of a nanoscale crystalline calcium phosphate, closely resembling hydroxyapatite, and an organic phase, which is composed largely of type I collagen fibers. Other constituents of bone tissue include water and organic molecules such as glycosaminoglycans, glycoproteins, lipids, and peptides. Ions such as sodium, magnesium, fluoride, and citrate are also present, as well as hydrogenophosphate. Hence, the mineral phase in bone may be characterized essentially as nonstoichiometric substituted apatite. Such a distinction is important in the development of synthetic calcium phosphates for application as skeletal implants. An understanding of bone function and its interfacial relationship to an implant clearly depends on the associated structure and composition. Therefore, it is essential to fully understand the chemical composition of bone, and Raman spectroscopy is an excellent technique for such an analysis.     

Two-spinor Formulation of First-Order Gravity Coupled to Dirac Fields

A two-spinor formalism for the Einstein Lagrangian is developed. The gravitational field is regarded as a composite object derived from soldering forms. Our formalism is geometrically and globally well-defined and may be used in virtually any 4m-dimensional manifold with arbitrary signature as well as without any stringent topological requirement on space-time, such as parallelizability. Interactions and feedbacks between gravity and spinor fields are considered. As is well known, the Hilbert–Einstein Lagrangian is second order also when expressed in terms of soldering forms. A covariant splitting is then analysed leading to a first-order Lagrangian which is recognized to play a fundamental role in the theory of conserved quantities. The splitting and thence the first-order Lagrangian depend on a reference spin connection which is physically interpreted as setting the zero level for conserved quantities. A complete and detailed treatment of conserved quantities is then presented.     

Stochastic resonance in a stochastic bistable system subject to additive white noise and dichotomous noise

The stochastic resonance (SR) in a stochastic stable system driven by a static force and a periodic square-wave signal as well as by additive white noise and dichotomous noise is considered from the point of view of the signal-to-noise ratio (SNR). It is found that the SNR exhibits SR behavior when it is plotted as a function of the noise strength of the white noise and dichotomous noise, as well as when plotted as a function of the static force. Moreover, the influence of the strength of the stochastic potential force and the correlation rate of the dichotomous noise is investigated.     

单偏振控制器环形腔光纤激光器实验研究

理论分析了非线性偏振旋转环形腔作为类饱和可吸收体获得脉冲的物理机理。在光纤环形腔结构中,采用单个偏振控制器实现了非线性偏振旋转锁模,直接获得了脉冲宽度为131 fs的超短脉冲输出。实验中,采用性能稳定的976 nm半导体二极管激光器作为抽运源,使用高掺杂浓度的Er3 光纤为增益介质,通过调节偏振控制器,获得了光谱谱宽(3 dB带宽处)为23.5 nm的稳定锁模脉冲输出。脉冲中心波长为1535.9 nm,平均功率为5.91 mW,脉冲重复率为11.20 MHz。     

金MPC掺杂琼脂-明胶复合泡沫的均匀性研究

 采用表面包覆水溶性硫醇单分子层的金团簇（MPC）对琼脂-明胶复合泡沫进行掺杂。研究表明,掺杂泡沫轴向密度均匀，金MPC粒径小，不聚焦，在泡沫中分散良好，掺杂对泡沫微观形貌没有明显影响。当掺杂泡沫密度低至5.8 mg/cmcm³，、掺杂质量分数高达30%时，金MPC在复合泡沫中不发生沉降或聚集。以水作溶剂，成功制得密度小于10 mg/cm³，孔径小于100 mm的金MPC掺杂琼脂-明胶泡沫靶材料。