共查询到17条相似文献,搜索用时 93 毫秒
1.
分析了楔形镜和中性玻璃衰减片组对光束的衰减原理,采用反射式楔形镜作为无像差定量衰减器,并同时使用中性玻璃衰减片组微调光束能量。实验测量了LD泵浦激光模式发生器基模和高阶模条件下激光束的M2因子,结果表明:楔形镜反射式衰减器对光束质量无显著影响,将楔形镜第一次表面反射作为无像差定量衰减,入射角在0~55°范围内,单棱镜表面反射光束能量为入射光能量的4.3%,通过多块组合可以得到更大的衰减;可采用中性玻璃衰减片组对激光光束的衰减进行精细控制,使其满足CCD探测器动态范围要求。该结论可为高精度激光参数测量装置光衰减系统的研制提供理论依据。 相似文献
2.
建立了角锥棱镜的偏振模型,分析了角锥棱镜对入射线偏振光的偏振态的影响,分析表明角锥棱镜的单个入射区域存在特殊的偏振方向,该方向的线偏振光被角锥棱镜反射后仍然是线偏振光。利用角锥棱镜的该特性设计了腔内存在线偏振光振荡的角锥棱镜激光谐振腔,能够使用电光开关调Q,在振动环境中具有较好的抗失调稳定性。研制了激光器样机并进行了实验,在重复频率为10 Hz时,输出激光单脉冲能量大于300 mJ,光束质量因子β值在2左右,实验结果也表明角锥棱镜的棱和顶点并不影响输出激光的光束质量。 相似文献
3.
4.
《光学学报》2016,(11)
角锥棱镜常被用作光电测距和光电跟踪的合作信标。在一些特殊应用场合中,要求被角锥棱镜反射的光束具有一定的发散角,以实现对远场不同位置处激光器和探测器的全覆盖。标准角锥棱镜不具备对光束发散的功能,但是可以利用角锥棱镜中光束出射点与入射点不同的特性,在标准角锥棱镜前加装平凹透镜来实现对反射光束的发散。采用理论分析方法和几何光学追迹模拟方法分析了利用平凹透镜和标准角锥棱镜实现反射光束发散的可行性,同时研究了反射光束发散半角与入射光束参数和平凹透镜几何参数的定量关系。理论和模拟结果都表明,当入射光束半径小于平凹透镜半径时,反射光束的发散半角随入射光束半径准线性增加;平凹透镜曲率半径越小,反射光束发散半角越大。 相似文献
5.
角锥棱镜常应用于光电跟踪、卫星通信、干涉仪等领域.在一些特殊应用场合中,要求经角锥棱镜反射的光束具有一定的发散角,以实现对距离激光器较远位置处探测器的覆盖.由于标准角锥棱镜不具备对光束发散的功能,本文利用含二面角误差的角锥棱镜对反射光束的不均匀发散特性,提出利用角锥棱镜阵列实现对反射光束均匀发散的方法和设计原则.采用衍射光学理论分析了所提方法及其设计原则的可行性,并依此设计了一个发散半角为0.5 mrad的角锥棱镜阵列.分析了光束参数、结构参数对反射光束远场衍射特性的影响,结果表明,入射光斑强度分布对反射光束发散半角没有影响,当角锥阵列满足点光源条件时,传输距离对反射光斑的角向均匀性没有影响;当阵元数超过一定值时,均匀性不再显著变化,但反射光斑的强度将进一步增加.在工程应用中,角锥棱镜阵列安装方位角误差对反射特性影响不显著,但角锥棱镜二面角的加工精度对反射特性影响较大,可通过进一步增加阵元数加以解决. 相似文献
6.
7.
8.
9.
10.
《中国光学与应用光学文摘》2006,(6)
P225.2 2006065054光束入射角对角锥合作目标激光测距的影响=Effect of beam incident angles on trihedral corner reflector laser ran- ging[刊,中]/陈浩(哈尔滨工业大学超精密光电仪器工程研究所,黑龙江.哈尔滨(150001)),谭久彬//光电子·激光.-2006,17(8).-986-988为了掌握光束入射角对角锥合作目标激光测距接收功率的影响规律,分析了光束入射角和角锥棱镜反射器有效反射面积的关系,利用有效反射面积推导了角锥棱镜反射器的激光雷达横截面(LRCS)随光束入射角变化的理论公式,进而得到激光测距系统接收功率随光束入射角变化 相似文献
11.
Periodic adjustment of the position of a laser beam spot on a semiconductor saturable absorber mirror in a passively mode-locked solid-state laser 下载免费PDF全文
A laser diode end-pumped passively mode-locked Nd:YVO4 solid-state laser with a semiconductor saturable absorber mirror (SESAM), in which the intracavity laser beam spot on the SESAM can be adjusted periodically, is investigated. Inserting a rectangular prism (RP) into the laser cavity is a promising approach towards the goal of periodically moving the position of the focus spot of the intracavity pulse on the SESAM surface to avoid the long-time irradiation of the laser beam on the same position, thereby solving a series of problems caused by damage to the SESAM and greatly prolonging its usage life. The adjustment of the rectangular prism in the laser cavity does not break the stable continuous wave (CW) mode-locked condition. The laser generates a stable picosecond pulse sequence at 1064 nm with an output power of 3.6 W and a pulse width of 14 ps. The instabilities of the output power and the pulse width are 1.77% and 4.5%, respectively. 相似文献
12.
A small rectangular laser spot has been widely studied for laser processing and laser repair technology. It is usually made by converging the input beam with the lens. Faithful reproduction of the laser spot is dependent on NA of the imaging lens. The small rectangular spot can be obtained by high NA lens, which is limited by many factors, such as high energy loss due to the reflection on the surface, large mass and volume, and strong sensitivity to aberrations and misalignment. On the other hand, the beam cannot be faithfully reproduced because of the diffraction with the low NA lens which has no such the limitations. One of the alternative ways to produce small rectangular profiles by using the low NA lens system is to estimate the input beam profile leading to the output profile of the sharp rectangular shape. 相似文献
13.
星间激光通信光束微弧度跟瞄性能检测装置的设计原理 总被引:5,自引:0,他引:5
基于矢量折射定理,研究了透射光束通过双棱镜实现微弧度量级偏转的设计原理,解决了星间激光通信精跟瞄检测的难题。推导了正交双棱镜实现光束偏转的精确公式,提出以水平张角和垂直张角表达光束视场,并说明了单棱镜实现光束偏转的一般情况。根据设计指标和计算结果确定了棱镜的主要参量,进而对光束的偏转结果进行了数值模拟。最后的实验结果与模拟结果基本一致。结果表明:取棱镜棱角α为4°时,棱镜每旋转1′,透射光束变化约1μrad;分别控制双棱镜在其最小偏向角一侧小角度偏转,可以实现光束在水平方向和垂直方向500μrad范围内的精确扫描,装置的扫描精度可以达到0.2μrad。 相似文献
14.
15.
Lalitha G. Nair 《Optics Communications》1977,23(2):273-274
It is shown that the dispersion of a prism beam expander used at very high angles of incidence has a large effect on the laser linewidth. 相似文献
16.
To generate a radially polarized laser beam we designed and fabricated a new Brewster optical element that consists of convex and concave conical prisms. The lateral surface of the convex conical prism was coated with a dielectric multilayer (SiO2 and Ta2O5) to enhance polarization selectivity. By combining two prisms we obtained a conical Brewster prism without beam divergence owing to refraction. A radially polarized TEM01* (R-TEM01*) mode laser beam was demonstrated when this prism was used inside a Nd:YAG laser cavity. 相似文献
17.
针对全反射棱镜式激光陀螺标度因数随温度周期性变化的现象,根据矩阵光学方法研究了稳频状态下温度变化对环形激光面积的影响,获得了全反射棱镜式激光陀螺标度因数与稳频电压的关系,并得出光束偏移是引起标度因数随温度周期性变化的原因。根据标度因数与稳频电压的关系,建立了全反射棱镜式激光陀螺标度因数补偿模型,通过实验对比了补偿前后标度因数的非线性度。结果表明,根据该补偿模型对全反射棱镜式激光陀螺标度因数进行补偿,标度因数非线性度提高了一个数量级以上,对提高全反射棱镜式激光陀螺的性能具有一定的参考价值。 相似文献