高功率二极管激光器相变冷却技术

根据高功率二极管激光器的散热需求,设计了一种储能式相变冷却实验系统,并开展了喷雾相变冷却器和微通道相变冷却器的设计。采用多孔微结构的换热表面,用氨做制冷剂,实现了喷雾相变冷却器表面温度37 ℃时,散热功率密度达到了511 W/cm2。采用节流汽化原理,分别设计了背冷式相变微通道冷却器和薄片型的模块式相变微通道冷却器,背冷式相变微通道冷却器采用氨做制冷剂, 散热功率密度达到了550 W/cm2,采用R124做制冷剂,散热功率密度约270 W/cm2。采用R124做制冷剂,实现了脉冲激光功率3 kW和连续激光功率100 W的相变冷却二极管激光器模块封装。     

石墨片作辅助热沉的高功率半导体激光器热传导特性

为使边发射高功率单管半导体激光器有源区温度降低,增加封装结构的散热性能,降低器件封装成本,提出一种采用高热导率的石墨片作为辅助热沉的高功率半导体激光器封装结构。利用有限元分析研究了采用石墨片作辅助热沉后,封装器件的工作热阻更低,散热效果更好。研究分析过渡热沉铜钨合金与辅助热沉石墨的宽度尺寸变化对半导体激光器有源区温度的影响。新型封装结构与使用铜钨合金作为过渡热沉的传统结构相比,有源区结温降低4.5 K,热阻降低0.45 K/W。通过计算可知,激光器的最大输出功率为20.6 W。在研究结果的指导下,确定铜钨合金与石墨的结构尺寸,以达到最好的散热效果。     

高密度封装二极管激光器阵列

 理论模拟了自制的高效冷却器的散热能力,分析了单元封装结构所需材料的导热特性,获得了高功率二极管激光器在高功率密度、高占空比条件下运行的可行性。改进了高密度封装的关键工艺,热沉金属化层达到了3~5 mm,焊料厚度为4~7 mm,封装间距0.6 mm,采用峰值功率1 kW的背冷式叠阵二极管激光器。实验测试结果表明:封装的二极管激光器叠阵单元的整体封装热阻为0.115 ℃/W,有良好的散热能力;该叠阵模块在电流为100 A、占空比15%时,输出峰值功率为986 W,峰值功率密度达到1.5 kW/cm2,平均每个板条的斜效率为1.25 W/A,激光器阈值电流为20 A左右。     

大功率半导体激光器叠层无氧铜微通道热沉

建立了叠层无氧铜微通道热沉的散热模型,通过理论计算和近似分析,优化了微通道热沉的结构参数;在t=200μm, ωc=60μm, ωf=100μm,p=2. 02×106 Pa时,可获得最小热沉热阻Rthm =4. 205×10-3 K·cm2 /W。根据优化结果,考虑微通道取向对液压降的影响,设计了一种新型大功率半导体激光器叠阵用五层结构叠层无氧铜微通道热沉,并结合实际工艺制备了无氧铜微通道热沉。在实际工作中,优化结果往往要跟实际工艺相结合,如优化所得的水压降为 2 02×106 Pa,这在实际工艺中较难实现。但在热沉实际工作的水压降条件下,热阻为 4. 982×10-3 K·cm2 /W,它能满足高功率激光器叠阵的需要。     

基于沸腾-空化耦合效应的微通道线阵LD用热沉

 针对大功率LD的冷却需求,基于沸腾-空化耦合效应,研制了一种微通道相变热沉,封装腔长1.5 mm的LD线阵。依据加工条件确定通道宽度、深度以及间距,采用2维数值模型估算了通道长度,热沉材料采用无氧铜,多层叠焊,外形尺寸为20 mm×12 mm×1.6 mm。实验测试了连续功率LD输出0～100 W时的电 光转换效率以及电流 输出功率等特性,冷却工质采用R134a,磁驱齿轮泵电机转速50 r/s时热沉热阻为0.3 ℃/W。结果显示微通道相变热沉具有良好的散热能力,能够满足大功率LD的散热要求。     

激光二极管高效铜微通道冷却器设计

 通过对铜微通道冷却器的散热分析，设计出５层结构的模块式铜微通道冷却器。采用常规的线切割工艺加工，散热通道宽大约200μm，深300μm，各层间用真空钎焊的方法组装。该冷却器对于腔长06mm、宽10mm的线阵激光二极管芯片热阻为0.58℃/W。通过面阵激光二极管封装实验证明，该冷却器可用于10％占空比工作的面阵激光二极管封装。     

20％占空比2．5kW二维叠阵二极管激光器

采用Cu-WCu复合结构研制了一种五层结构的模块式微通道冷却器，并用所研制的冷却器封装出了20％占空比工作，峰值功率2．5kW的二维叠阵DL。制作的冷却器为五层结构，由上盖片、上散热片、分水片、下散热片和下盖片扩散焊成。散热片和分水片采用具有高热导率的无氧铜制作，上、下盖片采用硬度高，热导率也较高的WCu合金制作。这种结构不仅避免了无氧铜较软，面形和棱边质量难控制的缺点，还可提高冷却器的强度，     

连续100W量子阱二极管激光器封装工艺

为了提高激光器输出功率,对研制的铜微通道冷却器性能进行了测试,分析了其散热能力。设计了一种在软焊料中掺杂金属添加剂的工艺,有效抑制了晶须生长,并利用该冷却器和新工艺封装出了连续100W大功率二极管激光器,并对封装的器件进行了性能测试。测试结果表明,封装的连续100W器件在工作电流105 A时,输出功率超过了100W,中心波长为808.5 nm,光谱半高宽为2.15 nm,器件的smile尺寸小于2μm,部分值小于0.5μm。     

二极管激光器阵列微通道冷却实验研究

针对某二极管激光器阵列现有冷却器的实际问题,设计并制作了一种铜基液冷微通道冷却器.采用细密的短微通道来代替原来较宽的长通道,大幅度提高了有限空间内的对流换热面积,并可充分利用入口效应来增强换热,从而在保持较低流动阻力、较高流体流量和较低流体温升的前提下,显著提高了冷却器整体冷却能力,并改善了冷却器与热源器件界面上的温度分布均匀性.在本实验最大流量G=70 mL/s情况下,微通道部分的压降只有10.3 kPa;当冷却器与热源器件界面上的平均温升为25.7 K时,冷却器的散热能力可达730 W,相当于128.5 W/cm2的界面热流密度.实验结果还验证了Shah和London提出的表观阻力系数关联式、用于预测平均努谢尔数的Sieder-Tate关联式以及Shah&London关联式.     

泵浦用高平均功率二极管激光器研制

针对高平均功率线阵二极管激光器(DL )芯片的工作要求,开展了相应的封装结构设计和高效冷却技术研究.封装的单条线阵DL连续输出激光功率50 W,工作寿命达到5 000 h,10%占空比准连续输出激光脉冲功率150 W,25%占空比准连续输出激光脉冲功率100 W,工作寿命达到5×109次脉冲.采用模块式封装方式由25个模块堆叠,制作出了连续激光功率1 kW和20%占空比工作脉冲功率2.5 kW的叠阵二极管激光器.     

Self-organization of five species in a cyclic competition game

Cyclic competition game models, particularly the “rock–paper–scissors” model, play important roles in exploring the problem of multi-species coexistence in spatially ecological systems. We propose an extended “rock–paper–scissors” game to model cyclic interactions among five species, and find that two of the five can coexistent when biodiversity disappears, which is different from the “rock–paper–scissors” game. As the number of fingers is five, we named the new model the “fingers” game, where the thumb, forefinger, middle finger, ring finger, and little finger cyclically dominate their subsequent species and are dominated by their former species. We investigate the “fingers” model in two ways: direct simulations and nonlinear partial differential equations. An important finding is that the number of species in a cyclic competition game has an influence on the emergence of biodiversity. To be specific, the “rock–paper–scissors” model is in favor of maintaining biodiversity in comparison with the “fingers” model when the variables (population size, reproduction rate, selection rate, and migration rate) are the same. It is also shown that the mobility and reproduction rate can promote or jeopardize biodiversity.     

Contrastive analysis on tone between Putonghua and Taiwan Mandarin

The differences of the pitch and duration of Chinese syllables between Putonghua （PTH） and Taiwan Mandarin （TM） were studied. The speech materials to be used are not only isolated syllables, but also sentences. The results reveal that： For the isolated syllables, T1 and T2 in TM are influenced by Minnan dialect, therefore their pitch are lower than those in PTH. T3 is fall-rise in PTH, while it is fall in TM. Moreover, the syllable duration sequence for different tone is T3〉T2〉T1〉T4 in PTH, while it is T1〉T2〉T3〉T4 in TM. For the syllables in sentences, T2 is mid-rise in PTH, while it is mid-level in TM. And the T3 is longer than T4 but shorter than T1 or T2 in PTH, while it is the shortest in TM. Furthermore the effects of prosodic phrase boundary on duration for different tones are almost the same in PTH, but the lengthening part of T1 or T2 is longer than that of T3 or T4 in TM.     

Experimental study on downstep in Chinese intonation

Downstep in pitch contour of Chinese Putonghua is examined using subtly designed sentences by controlling tone combinations. The results show both automatic and nonautomatic downstep phenomena exist in Chinese. In non-automatic downstep, low tones compress downwards the pitch range of the following syllables. and the main influence of downstep is on topline. Low tone not only lower the topline behind it, but also raise the high tones before it, the effects are compatible with each other. In automatic downstep, the topline of pitch contour in intonational phrase is presented as a linear downtrend, but it differs among speakers due to the effect of personal stress practice. In comparison with downstep phenomenon in other tone or non-tone languages, the downstep ratio in Chinese is not constant, and the domain of downstep is not limited within the adjacent tones.     

Abelian-Higgs phase of SU(2) QCD and glueball energy

It is shown that SU(2) QCD admits an dual Abelian-Higgs phase, with a Higgs vacuum of a type-Ⅱ superconductor. This is done by using a connection decomposition for the gluon field and the random-direction approximation. Using a bag picture with soft wall, we presented a calculational procedure for the glueball energy based on the recent proof for wall-vortices [Nucl. Phys. B 741(2006)1].     

Signal generation in an isotropic medium in scanning electron acoustic microscope

Based on the research in Ref. [5][Materials Science and Engineering, 1989; A122： 57 63], an improved model of heat source is set up, the different modes of Lamb wave in an isotropic sample generated by a chopped electron beam at frequency f are obtained with integral transform and normal function expansion method, and the output signal of PZT coupled at the back surface of the sample is found out. The generation mechanism of SEAM （Scanning Electron Acoustic Microscopy） signal is discussed. It shows that the SEAM is a near field imaging technique with high spatial resolution and its best lateral spatial resolution is about 2√2α （α is the radius of the focused electron beam）. Some of experimental results of SEAM images are presented in the paper and it shows that the spatial resolution of SEAM is better than 0.5 μm and smaller than the thermal diffusion length of the sample. Therefore the character of near field imaging in SEAM is also proved experimentally.     

High efficiency filtering using two-dimensional photonic crystal coupled cavity structures

Transmission spectra of coupled cavity structures (CCSs) in two-dimensional (2D) photonic crystals (PCs) are investigated using a coupled mode theory, and an optical filter based on CCS is proposed. The performance of the filter is investigated using finite-difference time-domain (FDTD) method, and the results show that within a very short coupling distance of about 3λ, where λ is the wavelength of signal in vacuum, the incident signals with different frequencies are separated into different channels with a contrast ratio of 20 dB. The advantages of this kind of filter are small size and easily tunable operation frequencies.     

Real-time restoration of rotational blurred image using gradient-loading

The key to the restoration of rotational motion blurred image is how to restore the image under a low cost and to correct the irreversibility of the degradation function matrix.Based on the special qualities of degradation function matrix and precise deduction in space-domain, we present a new approach using gradient-loading for restoration of rotational blurred image.By easily adding a gradient operator, the irreversibility of the original matrix is corrected and can be applied for inverse filtering then.Gradientloading is the optimized approach which combines the advantages of both the approaches using constrained least square filtering and traditional diagonal-loading.Compared with the approach using least square filtering, its peak signal-to-noise ratio (PSNR) is improved from 3.18 to 6.46dB, while the computing time is reduced to 1/2-1/3.Experimental results demonstrate the effectiveness, noise-resistibility, robustness, and low complexity of this approach, which make it more suitable for real-time environment.     

All-Optical Logic Device Using Bent Nonlinear Tapered Y-Junction Waveguide Structure

We propose an all-optical logic device made of a bent tapered Y-junction waveguide with a Kerr-type nonlinear interface. It could provide an AND gate, OR gate, and exclusive-OR (XOR) gate. We could obtain different transmission results by adjusting the bending angle. The numerical simulation results show that the device functions as AND, OR, and XOR gates.     

Real-time, continuous-wave terahertz imaging by a pyroelectric camera

Real-time, continuous-wave terahertz (THz) imaging is demonstrated. A 1.89-THz optically-pumped farinfrared laser is used as the illumination source, and a 124 × 124 element room-temperature pyroelectric camera is adopted as the detector. With this setup, THz images through various wrapping materials are shown. The results show that this imaging system has the potential applications in real-time mail and security inspection.