钼掺杂氧化锌薄膜的结构、光学和表面等离子体特性研究

室温下,通过直流磁控反应溅射在石英衬底上制备一系列钼掺杂氧化锌薄膜。分别采用X射线衍射(XRD)、原子力显微镜(AFM)、分光光度计及拉曼光谱仪研究了钼掺杂浓度对氧化锌薄膜结构、表面形貌、光学性能和表面等离子体特性的影响。XRD测试结果表明,零掺杂氧化锌薄膜结晶良好,呈c轴择优取向,掺杂后薄膜缺陷增多,结晶质量下降,当掺杂浓度达到3.93 Wt%时,薄膜由c轴择优取向的晶态转变为非晶态。AFM测试结果表明非晶态掺钼氧化锌薄膜表面光滑,粗糙度最低可达489 pm。透射光谱表明所有薄膜样品在可见光范围(400～760 nm)平均透过率均达到80%,禁带宽度随着掺杂浓度的提高从3.28 eV单调增加至3.60 eV。吸收光谱表明氧化锌薄膜表面等离子体共振吸收峰随钼掺杂量的增大发生蓝移,而拉曼光谱表明Mo重掺杂时ZnO薄膜表面拉曼散射信号强度显著降低。通过Mo掺杂获得非晶态氧化锌薄膜,拓宽了氧化锌薄膜材料的应用领域,同时研究了Mo掺杂浓度对氧化锌薄膜表面等离子体的调控作用,这对制备氧化锌基光子器件具有重要参考价值。     

厚度对未掺杂ZnO薄膜光谱性能的影响

X射线衍射光谱、拉曼光谱和紫外可见透射光谱技术是薄膜材料检测的重要技术手段。通过对薄膜材料光谱性能的分析,可以获得薄膜材料的物相、晶体结构和透光性能等信息。为了解厚度对未掺杂ZnO薄膜的X射线衍射光谱、拉曼光谱和紫外可见透射光谱性能的影响,利用溶胶-凝胶法在石英衬底上旋涂制备了不同厚度的未掺杂ZnO薄膜样品,并对薄膜样品进行了X射线衍射光谱、拉曼光谱和紫外可见透射光谱的检测。首先,通过X射线衍射光谱检测发现,薄膜样品呈现出（002）晶面的衍射峰,ZnO薄膜为六角纤锌矿结构,均沿着C轴择优取向生长,且随着薄膜厚度的增加,衍射峰明显增强,ZnO薄膜的晶粒尺寸随着膜厚的增加而长大。利用扫描电子显微镜对薄膜样品的表面形貌分析显示,薄膜表面致密均匀,具有纳米晶体的结构,其晶粒具有明显的六角形状。通过拉曼光谱检测发现,薄膜样品均出现了437 cm-1的拉曼峰,这是ZnO纤锌矿结构的特征峰,且随着薄膜厚度的增加,其特征拉曼峰强度也增加,进一步说明了随着ZnO薄膜厚度的增加,ZnO薄膜晶化得到了加强。最后,通过紫外可见透射光谱测试发现,随着膜厚的增加,薄膜的吸收边发生一定红移,薄膜样品在可见光区域内的透过率随着膜厚度增加而略有降低,但平均透过率都超过90%。通过对薄膜样品的紫外-可见透射光谱进一步分析,估算了薄膜样品的折射率,定量计算了薄膜样品的光学禁带宽度,计算结果表明：厚度的改变对薄膜样品的折射率影响不大,但其禁带宽度随着薄膜厚度的增加而变窄,且均大于未掺杂ZnO禁带宽度的理论值3.37 eV。进一步分析表明,ZnO薄膜厚度的变化与ZnO晶粒尺寸的变化呈正相关,本质上,吸收边或光学禁带宽度的变化是由于ZnO晶粒尺寸变化引起的。     

Mn掺杂对ZnO薄膜结构及发光性能的影响

利用脉冲激光沉积的方法在Si衬底上生长出了c轴高度取向的Mn掺杂ZnO薄膜.X射线衍射表明所有样品都具有纤锌矿结构,没有发现其它相,随着掺杂量的增加,c轴晶格常数增大.原子力显微镜结果显示:Mn的掺杂引起了ZnO薄膜表面粗糙度的变化.由光致发光谱发现,在387 nm附近出现了由于近带边自由激子复合引起的紫外峰,还有以4...     

低温缓冲层对氧化锌薄膜质量的影响

利用金属有机化学气相沉积(MOCVD)法,在Si衬底上外延生长ZnO薄膜。为了改善氧化锌薄膜的质量,首先在Si衬底上生长低温ZnO缓冲层,然后再生长高质量的ZnO薄膜。通过XRD、SEM、光致发光(PL)光谱的实验研究,发现低温ZnO缓冲层可有效降低ZnO薄膜和Si衬底之间的晶格失配以及因热膨胀系数不同引起的晶格畸变。利用低温缓冲层生长的ZnO薄膜的(002)面衍射峰的强度要比直接在Si上生长的ZnO薄膜样品的高,并且衍射峰的半高宽也由0.21°减小到0.18°,同时有低温缓冲层的样品室温下的光致发光峰也有了明显的增高。这说明利用低温缓冲层生长的ZnO薄膜的结晶质量和光学性质都得到了明显改善。     

MOCVD法生长SAWF用ZnO/Diamond/Si多层结构

使用等离子体辅助MOCVD系统在金刚石,硅衬底上成功地制备了氧化锌多层薄膜材料,通过两步生长法对薄膜质量进行了优化。XRD测试显示优化后的样品具有c轴的择优取向生长,PL谱测试表明样品经优化后不仅深能级发射峰消失,同时紫外发射峰增强。对优化后的样品的表面测试显示出较低的表面粗糙度。比较氧化锌多层薄膜结构的声表面波频散曲线,ZnO薄膜声表面滤波器受膜厚和衬底材料的影响较大。当ZnO薄膜较薄时,在它上面的传播速度将与衬底上的传播速度接近,与其他衬底上生长的薄膜相比,以金刚石这种快声速材料为衬底的ZnO多层薄膜结构,声表面波滤波器的中心频率将提高1倍左右。     

Sn掺杂ZnO薄膜的室温气敏性能及其气敏机理

采用化学气相沉积方法在预制好电极的玻璃基底上制备出Sn掺杂ZnO薄膜和纯ZnO薄膜. 两种样品典型的形貌为四足状ZnO晶须, 其直径约为150-400 nm, 呈疏松状结构. 气敏测试结果显示Sn掺杂ZnO薄膜具有优良的室温气敏性, 并对乙醇具有良好的气敏选择性, 而纯ZnO薄膜在室温条件下对乙醇和丙酮均没有气敏响应. X射线衍射结果表明两种样品均为六方纤锌矿结构. Sn掺杂ZnO样品中没有出现Sn及其氧化物的衍射峰, 其衍射结果与纯ZnO样品对比, 衍射峰向小角度偏移. 光致发光结果表明, Sn掺杂ZnO薄膜与纯ZnO薄膜均出现紫外发光峰和缺陷发光峰, 但是Sn的掺杂使得ZnO的缺陷发光峰明显增强. 将Sn掺杂ZnO样品在空气中退火后, 其室温气敏性消失, 说明Sn掺杂ZnO样品的室温气敏性可能与其缺陷含量高有关. 采用自由电子散射模型解释了Sn掺杂ZnO薄膜的室温气敏机理.     

不同生长条件下ZnO薄膜电学性质的研究

ZnO薄膜中的高的背景电子浓度能够对p型掺杂形成补偿,从而对p型掺杂造成障碍,了解高背景电子浓度的来源有助于对p型掺杂的研究。本文采用分子束外延技术在不同真空度下在a面蓝宝石衬底上生长了一系列氧化锌薄膜,发现在低真空度下生长的样品的载流子浓度较高,为10¹⁹ cm^-3量级;而高真空度下生长的样品,其载流子浓度比低真空生长的样品显著降低,降低了3个数量级。在相同条件下生长的样品,通过不同的后处理手段进行处理后,其电子浓度未发生明显变化,说明氧空位等本征缺陷不是ZnO薄膜中电子的主要来源,高背景电子浓度应该与生长过程中非故意引入的杂质相关。通过低温光致发光表征,发现低真空度下生长的样品在低温下3.366 eV处有强的施主束缚激子发光峰,而高真空度下生长的样品的此发光峰显著变弱。由此,高电子浓度被归结为与生长过程中非故意引入的氢杂质相关。     

铟磷共掺杂p型氧化锌薄膜形成机理和性质

利用射频磁控溅射在石英衬底上生长出铟磷共掺氧化锌薄膜(ZnO ∶ In,P),所用靶材为掺杂五氧化二磷(P₂O₅)和氧化铟(In₂O₃)的氧化锌(ZnO)陶瓷靶,掺杂质量分数分别为1.5%和0.3%,溅射气体为Ar和O₂的混合气体。原生ZnO薄膜是绝缘的, 600 ℃退火5 min后导电类型为n型,而800 ℃退火5 min后为p型。p型ZnO薄膜的电阻率、载流子浓度和霍尔迁移率分别为12.4 Ω·cm, 1.6×10¹⁷ cm^-3 和3.29 cm²·V^-1·s^-1。X射线衍射测量结果表明所有样品都只有(002)衍射峰,并与相同条件下生长的未掺杂ZnO相比向大角度方向偏移,意味着In和P都占据Zn位。XPS测试结果表明在共掺ZnO薄膜中P不是取代O而是取代Zn。因此,铟磷共掺ZnO薄膜中,In和P都取代Zn,并且P_Zn与2个锌空位(V_Zn)形成P_Zn-2V_Zn复合受主,薄膜表现为p型。     

常压MOCVD生长ZnO薄膜及其性质

用常压MOCVD在蓝宝石 (0 0 0 1)面上生长了氧化锌 (ZnO)薄膜。用AFM、室温PL谱、Hall测量、X射线双晶衍射、卢瑟福背散射 /沟道技术等分析方法研究了样品的表面形貌、结构性能、发光性能和电学性能。AFM分析结果显示 ,薄膜呈六角柱状结晶 ,表面平整 ,粗糙度 (RMS)为 6 .2 5 7nm ,平均晶粒直径达 1.895 μm。室温PL测量该样品在 380nm处有很强的近带边发射 ,半峰全宽为 15nm。使用Hall测量检查了薄膜的电学性质。室温下该样品的载流子浓度为 2× 10 17cm-3 ,迁移率为 75cm2 ·V-1·s-1。用X射线双晶衍射和卢瑟福背散射 /沟道效应研究了薄膜的结晶质量 ,样品的双晶衍射ω扫描半峰全宽为 0 .0 4° ,沟道效应的最小产额比χmin为 3.1%。     

RF磁控溅射条件对ZnO薄膜结构的影响

采用RF磁控溅射法在Si（001）衬底上制备ZnO薄膜。研究发现了工作中溅射频率、氧气和氩气流量比对样品结构的影响。样品的XRD图谱显示了强的（002）ZnO衍射峰，表明ZnO薄膜为c轴高取向生长。比较不同条件下制备的ZnO薄膜，研究发现当氧气和氩气的流量比相同时，随着溅射功率的增加，样品的（002）衍射峰增强，半高全宽变小。而当溅射功率相同时，随着氧气和氩气的流量比增加，样品的（002）衍射峰也增强，半高全宽同样变小。此外，本文还分析了溅射工艺和薄膜晶体质量之间关系，发现在相同的功率条件下，溅射率低时晶粒尺寸更大且薄膜的结晶性更好。     

Self-organization of five species in a cyclic competition game

Cyclic competition game models, particularly the “rock–paper–scissors” model, play important roles in exploring the problem of multi-species coexistence in spatially ecological systems. We propose an extended “rock–paper–scissors” game to model cyclic interactions among five species, and find that two of the five can coexistent when biodiversity disappears, which is different from the “rock–paper–scissors” game. As the number of fingers is five, we named the new model the “fingers” game, where the thumb, forefinger, middle finger, ring finger, and little finger cyclically dominate their subsequent species and are dominated by their former species. We investigate the “fingers” model in two ways: direct simulations and nonlinear partial differential equations. An important finding is that the number of species in a cyclic competition game has an influence on the emergence of biodiversity. To be specific, the “rock–paper–scissors” model is in favor of maintaining biodiversity in comparison with the “fingers” model when the variables (population size, reproduction rate, selection rate, and migration rate) are the same. It is also shown that the mobility and reproduction rate can promote or jeopardize biodiversity.     

Experimental study on downstep in Chinese intonation

Downstep in pitch contour of Chinese Putonghua is examined using subtly designed sentences by controlling tone combinations. The results show both automatic and nonautomatic downstep phenomena exist in Chinese. In non-automatic downstep, low tones compress downwards the pitch range of the following syllables. and the main influence of downstep is on topline. Low tone not only lower the topline behind it, but also raise the high tones before it, the effects are compatible with each other. In automatic downstep, the topline of pitch contour in intonational phrase is presented as a linear downtrend, but it differs among speakers due to the effect of personal stress practice. In comparison with downstep phenomenon in other tone or non-tone languages, the downstep ratio in Chinese is not constant, and the domain of downstep is not limited within the adjacent tones.     

Contrastive analysis on tone between Putonghua and Taiwan Mandarin

The differences of the pitch and duration of Chinese syllables between Putonghua （PTH） and Taiwan Mandarin （TM） were studied. The speech materials to be used are not only isolated syllables, but also sentences. The results reveal that： For the isolated syllables, T1 and T2 in TM are influenced by Minnan dialect, therefore their pitch are lower than those in PTH. T3 is fall-rise in PTH, while it is fall in TM. Moreover, the syllable duration sequence for different tone is T3〉T2〉T1〉T4 in PTH, while it is T1〉T2〉T3〉T4 in TM. For the syllables in sentences, T2 is mid-rise in PTH, while it is mid-level in TM. And the T3 is longer than T4 but shorter than T1 or T2 in PTH, while it is the shortest in TM. Furthermore the effects of prosodic phrase boundary on duration for different tones are almost the same in PTH, but the lengthening part of T1 or T2 is longer than that of T3 or T4 in TM.     

Abelian-Higgs phase of SU(2) QCD and glueball energy

It is shown that SU(2) QCD admits an dual Abelian-Higgs phase, with a Higgs vacuum of a type-Ⅱ superconductor. This is done by using a connection decomposition for the gluon field and the random-direction approximation. Using a bag picture with soft wall, we presented a calculational procedure for the glueball energy based on the recent proof for wall-vortices [Nucl. Phys. B 741(2006)1].     

Signal generation in an isotropic medium in scanning electron acoustic microscope

Based on the research in Ref. [5][Materials Science and Engineering, 1989; A122： 57 63], an improved model of heat source is set up, the different modes of Lamb wave in an isotropic sample generated by a chopped electron beam at frequency f are obtained with integral transform and normal function expansion method, and the output signal of PZT coupled at the back surface of the sample is found out. The generation mechanism of SEAM （Scanning Electron Acoustic Microscopy） signal is discussed. It shows that the SEAM is a near field imaging technique with high spatial resolution and its best lateral spatial resolution is about 2√2α （α is the radius of the focused electron beam）. Some of experimental results of SEAM images are presented in the paper and it shows that the spatial resolution of SEAM is better than 0.5 μm and smaller than the thermal diffusion length of the sample. Therefore the character of near field imaging in SEAM is also proved experimentally.     

High efficiency filtering using two-dimensional photonic crystal coupled cavity structures

Transmission spectra of coupled cavity structures (CCSs) in two-dimensional (2D) photonic crystals (PCs) are investigated using a coupled mode theory, and an optical filter based on CCS is proposed. The performance of the filter is investigated using finite-difference time-domain (FDTD) method, and the results show that within a very short coupling distance of about 3λ, where λ is the wavelength of signal in vacuum, the incident signals with different frequencies are separated into different channels with a contrast ratio of 20 dB. The advantages of this kind of filter are small size and easily tunable operation frequencies.     

Real-time restoration of rotational blurred image using gradient-loading

The key to the restoration of rotational motion blurred image is how to restore the image under a low cost and to correct the irreversibility of the degradation function matrix.Based on the special qualities of degradation function matrix and precise deduction in space-domain, we present a new approach using gradient-loading for restoration of rotational blurred image.By easily adding a gradient operator, the irreversibility of the original matrix is corrected and can be applied for inverse filtering then.Gradientloading is the optimized approach which combines the advantages of both the approaches using constrained least square filtering and traditional diagonal-loading.Compared with the approach using least square filtering, its peak signal-to-noise ratio (PSNR) is improved from 3.18 to 6.46dB, while the computing time is reduced to 1/2-1/3.Experimental results demonstrate the effectiveness, noise-resistibility, robustness, and low complexity of this approach, which make it more suitable for real-time environment.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

All-Optical Logic Device Using Bent Nonlinear Tapered Y-Junction Waveguide Structure

We propose an all-optical logic device made of a bent tapered Y-junction waveguide with a Kerr-type nonlinear interface. It could provide an AND gate, OR gate, and exclusive-OR (XOR) gate. We could obtain different transmission results by adjusting the bending angle. The numerical simulation results show that the device functions as AND, OR, and XOR gates.