宽带色散补偿光子晶体光纤的设计与优化

提出了一种新型的宽带色散补偿光子晶体光纤。通过增大光子晶体光纤(PCF)包层第一环空气孔半径r1,同时优化孔间距和包层其它环空气孔,在1550nm波长处获得了低至-1906.4ps/nm/km的负色散值。针对常规单模光纤的色散特性,设计出了宽带色散补偿光子晶体光纤,可补偿23倍长度的常规光纤,补偿的带宽达330nm,这在WDM系统中对多个信道同时进行色散补偿具有非常重要的意义。     

一种适于高速,多路通信系统的小色散单模光纤

给出了色散系数分别为（±２ｐｓ／ｋｍ／ｎｍ的小色散单模光纤一种可能的折射率分布及主要的设计参数，并讨论了此光纤在系统中的应用。结果表明小色散单模光纤具有的适当色散，既可有效抑制四波混频，又不致造成严重的色散限制，故适于高速、多路光纤通信系统采用。在系统中同时使用色散补偿技术时，在相邻在线放大器间采用ＩＴＵ－ＴＧ．６５２常规单模光纤结合负小色散单模光纤的方案不仅可有效地抑制四波混频并减小光纤色散限制，使１０×１０Ｇｂ／ｓ、１０级掺铒光纤放大器系统占用带宽从１６．２ｎｍ压缩到９．４ｎｍ；甚至可能实现等间距信道传输，从而大大简化了此类系统的设计     

中心下陷的负色散光纤

利用非等温等离子体化学气相沉积成功制得了具有折射率中心下陷的负色散光纤 (RDF)。该光纤在保持较好的抗弯曲性能与偏振模色散的同时 ,有效面积达到 4 5 μm2 ,且在 15 5 0nm处的色散为 - 19.6 5ps/(nm·km) ,色散斜率为 - 0 .132ps/(nm2 ·km)。此外 ,通过优化光纤纤芯各层的掺杂原子浓度 ,在 15 30nm处光纤的氢损降到了0 .0 1dB/km。由负色散光纤与具有超大有效面积的非零色散位移光纤 (ULAF)组成的色散管理光纤对在 15 30nm到16 2 5nm波长范围内的色散斜率小于 0 .0 0 6ps/(nm2 ·km) ,且最大色散值小于 0 .2ps/(nm·km)。同时 ,15 5 0nm波长处的衰耗为 0 .2 2 4dB/km ,且在 15 30nm到 16 2 5nm波段范围内衰耗较为平坦。该色散管理光纤对可以在无需色散补偿模块的前提下应用于大容量高速率的长距离波分复用 (WDM)系统。     

大容量长距离传输用低非线性效应非零色散位移光纤

利用非等温等离子体化学气相沉积 (PCVD)工艺制备了一种适合于大容量高速率长途干线网与城域网的中芯下陷型纤芯结构非零色散位移光纤。该光纤的有效面积大于 95 μm2 ,在 15 5 0nm波段的色散值约为9ps/(nm·km) ,有效的抑制了传输过程中光非线性效应的产生。通过对光纤剖面结构的优化设计 ,光纤的 15 5 0nm处的传输损耗降到约 0 .2 1dB/km ,与传统单模光纤的熔接损耗低于 0 .11dB ,且在直径为 6 0mm圆筒上绕 10 0圈后在 14 6 0nm到 16 2 5nm波长范围所引起的附加弯曲损耗均低于 0 .0 2dB/km。同时 ,该光纤色散斜率低于0 .0 6 5 ps/(nm2 ·km) ,偏振模色散 (PMD)小于 0 .0 5 ps·km-1/2 。此外 ,由于光纤的零色散点移到了 14 30nm以下 ,使波分复用 (WDM)传输在S波段 (14 6 0～ 15 30nm)、C波段 (15 30～ 15 6 5nm)、L(15 6 5～ 16 2 5nm)波段上都兼容。     

4×10 Gb/s 412 km密集波分复用光纤光栅色散补偿的实验

研制了一种多波长啁啾光纤布拉格 (Bragg)光栅 ,波长、波长间隔符合ITU T标准 ,利用这种多波长啁啾光栅可以同时对多信道波长进行色散补偿 ,光栅的每个波长补偿范围满足ITU T对应信道波长波动的要求 ,并进行了 4× 10Gb/s、4 12km波分复用色散补偿实验 ,实验结果比色散补偿光纤模块要好 ,无误码功率代价都小于 2dB。     

Theoretical analysis of the all-fiberized, dispersion-managed regenerator for simultaneous processing of WDM channels

The concept of the all-fiberized multi-wavelength regenerator is analyzed, and the design methodology for operation at 40 Gb/s is presented. The specific methodology has been applied in the past for the experimental proof-of-principle of the technique, but it has never been reported in detail. The regenerator is based on a strong dispersion map that is implemented using alternating dispersion compensating fibers (DCF) and single-mode fibers (SMF), and minimizes the nonlinear interaction between the wavelength-division multiplexing (WDM) channels. The optimized regenerator design with + 0.86 ps/nm/km average dispersion of the nonlinear fiber section is further investigated. The specific design is capable of simultaneously processing five WDM channels with 800 GHz channel spacing and providing Q-factor improvement higher than 1 dB for each channel. The cascadeability of the regenerator is also indicated using a 6-node metropolitan network simulation model.     

Anomalous dispersion in a solid, silica-based fiber

We demonstrate an all-solid (nonholey), silica-based fiber with anomalous dispersion at wavelengths where silica material dispersion is negative. This is achieved by exploiting the enhanced dispersion engineering capabilities of higher-order modes in a fiber, yielding + 60 ps/nm km dispersion at 1080 nm. By coupling to the desired higher-order mode with low-loss in-fiber gratings, we realize a 5 m long fiber module with a 300 fs/nm dispersion that yields a 1 dB bandwidth of 51 nm with an insertion loss of approximately 0.1 dB at the center wavelength of 1080 nm. We demonstrate its functionality as a critical enabler for an all-fiber, Yb-based, mode-locked femtosecond ring laser.     

Experimental realization of a novel dispersion- compensating optical fiber amplifier for simultaneous compensation of positive dispersion and losses

Erbium-doped dispersion-compensating optical fiber (EDCF) has been theoretically simulated and experimentally fabricated using Modified Chemical Vapor Deposition (MCVD) for optimum operation at 5.0km. It is optimized for both gain as well as negative dispersion. The erbium has been doped into the cladding region while the core of the optical fiber is chosen to be narrow so as to have a high negative dispersion. Measured gain of 3.1 dB at 200 m using 100 mW pumping power (980 nm wavelength) at 1550 nm has been obtained and the gain of 32 dB at 5.0 km using same pumping scheme has been predicted. The chromatic dispersion of this EDCF has been also measured to be –43.5 ps/km-nm at 1550 nm and thus, providing the dispersion of –217.5 ps/nm at 5 km. The bend-induced losses are found to be negligible. We are the first to report the experimental realization of EDCF.     

实用化少模光纤的研究

针对大容量光纤通信系统,设计了一种实用化的椭圆纯硅芯少模光纤,给出了光纤的设计原理与参考标准,运用全矢量有限元法结合完美匹配层边界条件分析了光纤的传输特性.在1.4~1.65μm波长处,光纤处于稳定的HE_(11)和HE_(21)双模运转,模式有效折射率差大于1.8×10~(-3),避免了模间耦合和串扰;在工作波长1.55μm处,HE_(11)和HE_(21)模的色散系数分别为19.61和4.41ps/(nm·km),色散斜率分别为0.048和0.002ps/(nm~2·km),模场面积分别为97.17和143.96μm2,模式的衰减系数均小于0.21dB/km.该光纤的传输特性基本符合G.652和G.655光纤标准,可利用现有成熟的"预制棒拉丝工艺"制备,同时与波分复用技术相结合可以成倍提升光网络的传输容量,对于下一代通信网络带宽的提升具有重要意义.     

Recent progress in soliton transmission technology

Recent progress on time-division multiplexed (TDM) and wavelength-division multiplexed (WDM) soliton transmission is described, in which dispersion management plays an important role in increasing the power margin and the dispersion tolerance. The characteristics of the dispersion-managed soliton are compared with those of return to zero and nonreturn to zero pulses. With a small dispersion swing, the system can still be described as an average soliton using the nonlinear Schrodinger equation, while with a large dispersion swing, the solitonlike steady-state pulse becomes a chirped Gaussian pulse, in which the governing equation is closer to a linear Schrodinger equation with a parabolic potential well. We describe an in-line modulation scheme for up to 80 Gbit/s per channel and its two channel WDM transmission over 10 000 km. Finally, we describe 640 Gbit/s (40 Gbit/sx16 channels) WDM soliton transmission over 1000 km with a dispersion-managed single-mode fiber. (c) 2000 American Institute of Physics.     

Temperature dependence of chromatic dispersion in various types of optical fiber

The temperature dependence of chromatic dispersion is examined for various types of fiber. Its coefficient is found to depend strongly on the dispersion slope. Dispersion-flattened fiber has a significantly low coefficient of -0.0005(ps/nm/km)/ degrees C , compared with -0.0038(ps/nm/km)/ degrees C for large-core nonzero dispersion-shifted fiber. Transmission lines with low dispersion slopes consisting of pure silica core fiber and dispersion-compensating fiber also exhibit low coefficients of less than -0.001(ps/nm/km)/ degrees C because of their compensating effects.     

通信系统中色散补偿光纤的研究

对五包层色散补偿光纤进行了研究,分析了各个参量对色散补偿光纤性能的影响,发现色散补偿光纤只有在一定范围的拉丝芯径内,以牺牲负色散数值为代价才能获得较大的负色散斜率。在1550nm处获得了不大于150ps/(nm·km)的负的总色散和负色散斜率的色散补偿光纤。采用在光纤拉丝时旋转预制棒的工艺减小了光纤的偏振模色散,并采用化学汽相沉积(MCVD)光纤生产工艺,研制出了性能较好的色散补偿光纤。     

Simultaneous Compensation of Dispersion and Losses using Er-Doped Double-Core Optical Fiber

The Er-doped double-core dispersion compensating fiber (EDDCF) has been fabricated using modified chemical vapor deposition (MCVD) technique. We have obtained 14 dB gain at 1550 nm (using a diode laser of 980 nm wavelength which provides 100 mW of pump power) with dispersion of about −165 ps/km nm. It is useful for the optical fiber network where amplification as well as negative dispersion is necessary. We are the first to report the experimental realization and characterization of the EDDCF.     

Using dual-mode self-locked semiconductor laser for optical millimeter-wave application

In this study, an optical millimeter-wave (mm-wave) generator is proposed and experimentally demonstrated by using a self-injected Fabry-Perot laser diode (FP-LD), having mode spacing of 1.11 nm, for dual-mode beating in 140 GHz band (terahertz band). The created dual-wavelength also can be also modulated at 1.25, 2.5, and 10 Gb/s with on-off keying (OOK) modulation format by external optical modulator, respectively, in 20 km fiber transmission. Moreover, the dual-mode laser can be selected in difference wave-lengths by tuning the optical filter inside cavity for the future WDM applications.     

Experiment on Channel-switching Add/Drop Multiplexer in a Multi-channel WDM System

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｔｈｅｏｐｔｉｃａｌａｄｄ ｄｒｏｐｍｕｌｔｉｐｌｅｘｅｒ(ＯＡＤＭ )ｉｓｅｘｐｅｃｔｅｄｔｏｐｌａｙａｎｉｍｐｏｒｔａｎｔｒｏｌｅｉｎｆｕｔｕｒｅｗａｖｅｌｅｎｇｔｈｄｉｖｉｓｉｏｎｍｕｌｔｉｐｌｅｘｅｄ(ＷＤＭ )ｒｉｎｇｎｅｔｗｏｒｋ .Ｕｐｔｏｎｏｗ ,ａｆｅｗｓｃｈｅｍｅｓｏｆＯＡＤＭｂａｓｅｄｏｎｗａｖｅｌｅｎｇｔｈｇｒａｔｉｎｇｒｏｕｔｅｒ,ｏｐｔｉｃａｌｓｗｉｔｃｈｅｓ,ａｒｒａｙｅｄｇｒａｔｉｎｇｗａｖｅｇｕｉｄｅａｎｄｆｉｂｅｒＢｒａｇｇ ｇｒａｔｉｎｇｓ(…     

Experiment on Channel-switching Add/Drop Multiplexer in a Multi-channel WDM System

A channel-switching optical add/drop multiplexer with tunable fiber Bragg grating tuned by equivalent-intensity cantilever beam is proposed and experimentally demonstrated. The no-chirped linearly tuning range is about 6.1 nm, which enables it to add or drop 8 channels with channel spacing 100 GHz. It is used in a 4-channel WDM system to test its capability. The adjacent channel isolation is not less than 24 dB. 4-channel lasers modulated by 1.2 Gb/s Non-Return-to-Zero format (NRZ), \{Return-to-Zero\} format (RZ) and 2.5 GHz analogue signals are dropped by the device after transmission over 100 km and the results are given.     

Analysis of the Crosstalk in WDM Systems Caused by Cross-phase Modulation in Erbium-doped Fiber Amplifiers

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｃｒｏｓｓ ｐｈａｓｅｍｏｄｕｌａｔｉｏｎ (ＸＰＭ )ｈａｓａｎｉｍｐｏｒｔａｎｔｉｍｐａｃｔｏｎｔｈｅｐｅｒｆｏｒｍａｎｃｅｏｆｈｉｇｈ ｓｐｅｅｄｗａｖｅｌｅｎｇｔｈｄｉｖｉｓｉｏｎｍｕｌｔｉｐｌｅｘｉｎｇ(ＷＤＭ )ｏｐｔｉｃａｌｆｉｂｅｒｃｏｍｍｕｎｉｃａｔｉｏｎｓｙｓｔｅｍ[1,2 ] .ＩｔｃａｕｓｅｓｃｒｏｓｓｔａｌｋｂｅｔｗｅｅｎｓｉｍｕｌｔａｎｅｏｕｓｌｙｔｒａｎｓｍｉｔｔｉｎｇｃｈａｎｎｅｌｓｉｎＷＤＭｓｙｓｔｅｍｓａｎｄｉｓｂｅｌｉｅｖｅｄｔｏｂｅａｓｉｇｎ…     

光纤非线性效应对10 Gb/s波分复用色散补偿系统的限制

对信道间距为１００ＧＨｚ的８倍１０Ｇｂ／ｓ波分复用色散补偿系统进行了计算机仿真,分析了光纤的色散和自相位调制（ＳＰＭ）、互相位调制（ＸＰＭ）、四波混频（ＦＷＭ）等非线性效应在具有级联光放大器系统中的作用。四种色散补偿方案是：ＳＭＦ（常规单模光纤）＋ＤＣＦ１（色散斜率为正的色散补偿光纤）、ＳＭＦ＋ＤＣＦ２（色散斜率为负的色散补偿光纤）、ＴＷ１（色散为正的非零色散光纤）＋ＴＷ２（色散为负的非零色散光纤     

Gain Flattening Approach to Physical EDFA for 16 × 40 Gb/s NRZ-DPSK WDM Optical Communication Systems

We are using different approaches to gain flattening in EDFAs without using additional components; i.e., gain flattening filter, dispersion shift fiber, periodic gratings, etc. By using gain flatten approach 3, it is possible to achieve the transmission of sixteen channels at 40 Gb/s wavelength division multiplexing (WDM) over a transmission distance of 490 km by single-mode fiber and dispersion-compensating fiber at a span of 70 km with channel spacing of 200 GHz. We observed the bit error rate less than 10^-9 and power of received signal more than -5 dBm with NRZ-DPSK format.     

Broadband dispersion-compensating photonic crystal fiber

We present a modified dual-core photonic crystal fiber, based on pure silica, with special grapefruit holes in the inner cladding. The fiber has large, broadband negative dispersion, and the dispersion value varies linearly from -380 t o-420 ps/(nm km) in the C band. To decrease the fabrication difficulty, large air holes are adopted. Furthermore, the chromatic dispersion of the fiber is not sensitive to the structure parameters. So the proposed fiber structure can greatly facilitate fiber drawing and can be used for broadband dispersion compensation.