超强飞秒激光与固体靶产生的超热电子加热机制

 在SILEX-1激光器上测量了超强飞秒激光与Ta靶相互作用产生的出射超热电子能谱及角分布，研究了出射超热电子加热机制。激光脉宽为 30 fs，激光功率密度为8.5×10¹⁸ W/cm²。靶前法线方向超热电子温度为550 keV。从实验结果可知：共振吸收是靶前法线方向超热电子主要加热机制，这与靶前存在大密度标长预等离子体的实验条件吻合。靶厚为6～50 μm时，靶后超热电子沿法线方向出射；靶厚为2 mm时，该发射峰消失。     

飞秒激光-薄膜靶相互作用中超热电子产额和激光转化效率

 在激光能量130 mJ（靶面），脉宽60 fs，波长800 nm，对比度1∶10^-6，激光与靶法线成45°夹角，P偏振，靶面激光峰值功率密度约为7.0×10¹⁷ W·cm^-2，无预脉冲的条件下，采用电子谱仪与经γ标准源标定的LiF热释光探测器（TLD）相配合，测量了飞秒激光-薄膜靶相互作用中产生的超热电子能谱。根据所测的能谱，推算出超热电子的产额和激光能量转化为超热电子能量的效率，在靶法线方向分别为1.19×10¹⁰/sr和4.55%/sr，在激光反射方向分别为1.83×10⁹/sr和0.76%/sr。结果显示，不同方向的超热电子产额和激光转化效率有所不同，原因在于激光-等离子体相互作用产生的超热电子构成各向异性的分布。     

天光一号打靶聚焦系统的研制

 介绍了在天光一号MOPA光学角多路系统中，将6束KrF准分子激光引入靶室的方法以及聚焦系统的研制。用紫外CCD相机测得6束激光聚到平面靶上的焦斑直径为290μm，靶上的功率密度达到8×10¹² W/cm²。     

利用侧向阴影照相技术探测靶的飞行速度

 建立起一套侧向阴影照相的光学系统,利用可见光作为探测光,在状态方程实验中对靶的飞行速度进行探测。在天光KrF准分子激光装置上进行激光打靶实验,激光波长为248.4 nm。在激光功率密度为8.3×10¹¹ W/cm²的条件下,测得50 μm厚铝靶的飞行速度为3.28 km/s;在激光功率密度为4.7×1010¹¹ W/cm²的条件下,测得带100 μm厚烧蚀层的13 μm厚铝靶的飞行速度为2.52 km/s。最后进行了误差分析计算,实验中探测激光与靶表面偏离角度最大不会超过2.06°,偏离角对实验精度产生的影响可以被忽略。     

等离子体屏蔽和稀疏波对冲量耦合系数的影响

 利用脉冲Nd:YAG激光作用在铝、铜靶上，研究了不同入射激光能量下冲量耦合系数和离焦量之间的关系，以及不同功率密度情况下冲量耦合系数和光斑直径的关系。实验表明铝靶在入射激光脉冲能量由75.8 mJ增加到382.3 mJ时，冲量耦合系数峰值对应的最佳离焦量由－10 mm处远离焦点向透镜方向移到－18 mm，而对应的激光功率密度仅由2.0×10⁹ W/cm²增加到3.9×10⁹ W/cm²；铜靶实验规律和铝靶类似。等离子体屏蔽的吸收作用导致了冲量耦合系数达到最大值后迅速降低。铝靶在入射激光功率密度由0.7×10⁹ W/cm²增大到1.0×10¹⁰W/cm²时，冲量耦合系数随光斑直径增大而增大，对应变化斜率由5.2×10^-5N·s/（mm·J）增大到49.2×10^-5N·s/（mm·J），表明了稀疏波对冲量耦合系数的削弱作用随入射激光功率密度增加而增加，随光斑直径增大而减小。     

激光功率密度对Al膜靶后表面快电子发射的影响

 报道了在20 TW皮秒激光器上完成的p偏振激光与等离子体相互作用过程中产生的快电子的角分布和能谱测量结果。实验得到：当激光功率密度小于10¹⁷ W/cm²时,电子发射没有明显定向性,在激光入射面内多峰发射;当激光功率密度大于10¹⁷ W/cm2,小于10¹⁸ W/cm²时,电子主要沿靶面法线方向发射;当激光功率密度达到相对论强度时,电子主要沿激光传播方向发射;激光功率密度未达到相对论强度时,靶后表面法线方向快电子能谱拟合平均温度符合共振吸收温度定标率;激光功率密度达相对论强度以上时,靶后表面法线方向快电子能谱拟合平均温度高于已有的温度定标率。     

超短脉冲强激光与固体靶相互作用中Kα射线的实验研究

在相对论激光强度下，对p偏振30 fs激光与固体Cu靶相互作用中产生的Kα射线进行了实验研究.采用刀边成像技术和单光子计数X射线CCD相结合的探测装置，在单发激光脉冲打靶时同时得到X射线源的尺寸、能谱以及Kα光子的转换效率等多种信息.实验结果与Reich等人的理论计算结果有明显的差异，Kα光子的能量转换效率在激光功率密度为1.6×10¹⁸W/cm²的条件下达到最大值7.08×10^-6/sr.根据这一结果并结合蒙特卡罗程序，推断出在这一聚焦光强下激光能量转换为前向超热电子的效率约为10%.     

飞秒激光与固体靶相互作用中自生磁场的测量

 利用OMA光学多道分析谱仪，分别在激光镜反方向和接近靶面法线方向测量了2倍频谐波的精细结构。在激光功率密度为5×10¹⁷ W/cm²的条件下，通过散射光2倍频谐波谱的精细结构，回推出激光与等离子体相互作用中产生的自生磁场达100T量级。     

超短超强激光与薄膜靶作用的光学光谱

 在SILEX-Ⅰ超短超强激光装置上,研究了30 fs,1.0×10¹⁹ W/cm²超短超强激光脉冲与薄膜靶作用产生的发射光谱。对于3 μm厚的铜靶,在激光沿靶面的镜面反射方向观测到二倍频和3/2倍频光谱,且都发生了红移。由红移量推测出等离子体反射面的后退速度约为2.6×10⁸ cm/s。对于200 nm厚CH靶,沿激光传播方向观察到超连续光谱,光谱波长范围从约300 nm延伸至约940 nm。利用MULTI-1D流体程序,模拟了超强激光的预脉冲与薄膜靶相互作用过程,结果表明,预脉冲对预等离子体的密度分布有显著影响,是导致实验观测光谱差异的原因。     

紫外超短脉冲激光辐照固体靶产生硬X射线研究

 实验研究了紫外高强度超短脉冲激光(248nm, 440fs, 50mJ)辐照固体靶时产生的硬X-射线(>30 keV)能量连续谱，靶上强度达到10¹⁷ W/cm²。P极化光45°照射5mm铜片，实验探测到了能量大于200keV的X射线信号，利用Maxwellian分布拟合能谱得到了的超热电子温度为67keV。     

通道靶对超强激光加速质子束的聚焦效应

发散角过大是制约超强激光与固体靶相互作用加速产生高能质子束应用的一个重大物理难题.本文提出了一种结构化的通道靶型,与超强激光相互作用可提高质子束的发散特性,通道壁上产生的横向电荷分离静电场可对质子有效聚焦.采用二维particle-in-cell粒子模拟程序对激光通道靶相互作用过程进行了研究,分析了加速质子束的性能特点.模拟结果表明,与传统平面靶相比,通道靶可以在不过多损失能量的情况下产生具有更好准直性的质子束,尤其当通道靶的直径与激光焦斑尺寸和质子源尺寸相当时,横向静电场能够有效聚焦质子束,并且可保证相对较高的激光能量利用率.     

Dynamics of electric fields driving the laser acceleration of multi-MeV protons

The acceleration of multi-MeV protons from the rear surface of thin solid foils irradiated by an intense (approximately 10(18) W/cm2) and short (approximately 1.5 ps) laser pulse has been investigated using transverse proton probing. The structure of the electric field driving the expansion of the proton beam has been resolved with high spatial and temporal resolution. The main features of the experimental observations, namely, an initial intense sheath field and a late time field peaking at the beam front, are consistent with the results from particle-in-cell and fluid simulations of thin plasma expansion into a vacuum.     

Enhancement of proton acceleration by hot-electron recirculation in thin foils irradiated by ultraintense laser pulses

MeV-proton production from solid targets irradiated by 100-fs laser pulses at intensities above 1x10(20) W cm(-2) has been studied as a function of initial target thickness. For foils 100 microm thick the proton beam was characterized by an energy spectrum of temperature 1.4 MeV with a cutoff at 6.5 MeV. When the target thickness was reduced to 3 microm the temperature was 3.2+/-0.3 MeV with a cutoff at 24 MeV. These observations are consistent with modeling showing an enhanced density of MeV electrons at the rear surface for the thinnest targets, which predicts an increased acceleration and higher proton energies.     

Beam quality improvement and focused peak intensity measurement of an intense femtosecond Ti:sapphire laser system

Micro-lens arrays were adopted to homogenize the beam profile of 532-nm pumping laser for the main amplifier of an intense femtosecond, chirped pulse amplification (CPA) Ti:sapphire laser. Experimental measurements showed a great improvement of the near-field pattern of the CPA beam after the main amplifier and the size of the focal spot was improved from 2.7 times diffraction limitation (DL) to 1.6 DL.The spot size focused by an f/4 off-axis parabola (OAP) in the target chamber was measured to be 5.8μm (full-width at half-maximum (FWHM)), and a peak intensity of 2.6 × 1020 W/cm2 was obtained at the output power of 120 TW. Peak intensity exceeding 1021 W/cm2 or even 1022 W/cm2 can be expected with smaller f-number focusing configuration and wavefront correction.     

X-Rays emission by high-intensity pulsed lasers irradiating thin foils at PALS laboratory

X-rays and forward ion emission from laser-generated plasma in the Target Normal Sheath Acceleration regime of different targets with 10-μm thickness, irradiated at Prague Asterix Laser System (PALS) laboratory at about 10¹⁶ W/cm² intensity, employing a 1,315 nm-wavelength laser with a 300-ps pulse duration, are investigated. The photon and ion emissions were mainly measured using Silicon Carbide (SiC) detectors in time-of-flight configuration and X-ray streak camera imaging. The results show that the maximum proton acceleration value and the X-ray emission yield growth are proportional to the atomic number of the irradiated targets. The X-ray emission is not isotropic, with energies increasing from 1 keV for light atomic targets to about 2.5 keV for heavy atomic targets. The laser focal position significantly influences the X-ray emission from light and heavy irradiated targets, indicating the possible induction of self-focusing effects when the laser beam is focalized in front of the light target surface and of electron density enhancement for focalization inside the target.     

Strong-field above-threshold photoemission from sharp metal tips

We present energy-resolved measurements of electron emission from sharp metal tips driven with low energy pulses from a few-cycle laser oscillator. We observe above-threshold photoemission with a photon order of up to 9. At a laser intensity of ～ 2 × 10(11) W/cm2 the suppression of the lowest order peak occurs, indicating the onset of strong-field effects. We also observe peak shifting linearly with intensity, with a slope of around -1.0 eV/(10(12) W/cm2). We attribute the magnitude of the laser field effects to field enhancement taking place at the tip's surface.     

MeV ion jets from short-pulse-laser interaction with thin foils

Collimated jets of carbon and fluorine ions up to 5 MeV/nucleon ( approximately 100 MeV) are observed from the rear surface of thin foils irradiated with laser intensities of up to 5 x 10 (19)W/cm(2). The normally dominant proton acceleration could be surpressed by removing the hydrocarbon contaminants by resistive heating. This inhibits screening effects and permits effective energy transfer and acceleration of other ion species. The acceleration dynamics and the spatiotemporal distributions of the accelerating E fields at the rear surface of the target are inferred from the detailed spectra.     

飞秒激光-物质相互作用产生Kα X射线

 用无色散X射线谱仪分别在靶前后测量了飞秒激光辐照铜箔产生的Kα X射线,获得了能量转换效率。入射激光脉冲宽度33 fs,能量在50 mJ～5 J,强度10₁₇～10₁₉ W/cm₂。靶后发射的Kα X射线强度随入射激光能量的增加而增加,其单色性较靶前好。采用100 μm厚靶,其能量转换率为2.2×10_-5。     

Enhancement of high energy proton yield with a polystyrene-coated metal target driven by a high-intensity femtosecond laser

We present experimental results on protons accelerated up to 950 keV from a 3-μm thick tantalum foil with a 133-nm thick polystyrene layer on its rear surface, irradiated with a laser pulse having the duration of 70 fs and the intensity of 2.7×10¹⁸ W/cm². The energy distribution of fast protons was measured simultaneously with that of the hot-electrons from the rear surface. The proton yield from the polystyrene-coated target is about 10 times as high as that from the uncoated metal target. This enhancement of the proton yield is roughly proportional to the increase of hydrogen atoms given by the 133-nm thick polystyrene layer, assuming a contaminant layer of ∼10-nm thickness is on the metal surface without coating. This result shows that the polystyrene layer contributes to the yield enhancement. PACS 52.38.Kd; 52.50.Jm; 52.59.-f     

铝靶三倍频激光烧蚀参数实验研究

叙述了采用时间空间积分晶体谱仪和时间分辨晶体谱仪等探测器测量铝平面靶强激光烧蚀参数的方法，给出了三倍频强激光烧蚀铝平面靶的质量烧蚀速率和烧蚀压。实验结果与收集到的国外数据进行了比较，它们在误差范围内一致。