Conductivity and oxygen permeability of a novel oxide Pr2Ni0.8 − x Cu0.2FexO4 and its application to partial oxidation of CH4

Iron-doped Pr₂Ni_0.8Cu_0.2O₄ was studied as a new mixed electronic and oxide-ionic conductor for use as an oxygen-permeating membrane. An X-ray diffraction analysis suggested that a single phase K₂NiF₄-type structure was obtained in the composition range from x = 0 to 0.05 in Pr₂Ni_0.8 − xCu_0.2Fe_xO₄. It is considered that the doped Fe is partially substituted at the Ni position in Pr₂NiO₄. The prepared Pr₂NiO₄-based oxide exhibited a dominant hole conduction in the P_O2 range from 1 to 10^− 21 atm. The electrical conductivity of Pr₂Ni_0.8−xCu_0.2Fe_xO₄ is as high as 10² S cm^− 1 in the temperature range of 873–1223 K and it gradually decreased with the increasing amount of Fe substituted for Ni. The oxygen permeation rate was significantly enhanced by the Fe doping and it was found that the highest oxygen permeation rate (60 μmol min^− 1 cm^− 2) from air to He was achieved for x = 0.05 in Pr₂Ni_0.8 − xCu_0.2Fe_xO₄. Since the chemical stability of the Pr₂NiO₄-based oxide is high, Pr₂Ni_0.75Cu_0.2Fe_0.05O₄ can be used as the oxygen-separating membrane for the partial oxidation of CH₄. It was observed that the oxygen permeation rate was significantly improved by changing from He to CH₄ and the observed permeation rate reached a value of 225 μmol min^− 1 cm^− 2 at 1273 K for the CH₄ partial oxidation.     

Oxygen non-stoichiometry and electrical conductivity of Pr2−xSrxNiO4±δ with x = 0–0.5

Oxygen non-stoichiometry and electrical conductivity of the Pr_2−xSr_xNiO_4±δ series with x = 0.0–0.5 were investigated in Ar/O₂ (pO₂ = 2.5 to 21 000 Pa) within a temperature range of 20–1000 °C. The equilibrium values of oxygen non-stoichiometry and electrical conductivity of these nickelates were determined as functions of temperature and oxygen partial pressure (pO₂). The nickelates with x = 0–0.5 appear to be p-type semiconductors in the investigated temperature and pO₂ ranges. The nickelates with x = 0.3–0.5 show very feebly marked pO₂ dependencies of the conductivity. Pr_1.7Sr_0.3NiO_4±δ shows the anomalies of the conductivity versus oxygen partial pressure which can be related to the orthorhombic–tetragonal crystal structure transformations. The conductivity of the Pr_2−xSr_xNiO_4±δ samples correlates with the average oxidation state of the nickel cations. The samples with x = 0.5 have the highest nickel oxidation state (≈ 2.5+), the highest [Ni³⁺]/[Ni²⁺] ratio close to 1 and show the highest conductivity (≈ 120 S/cm) in the whole pO₂ and temperature ranges investigated.     

Preparation and characteristics of Pr1.6Sr0.4NiO4+YSZ as composite cathode of solid oxide fuel cells

Composite cathodes of (1?x wt%)Pr_1.6Sr_0.4NiO₄+(x wt%)Y₂O₃-stabilized ZrO₂ (YSZ; x=0, 10, 20, 30, 40) abbreviated as Pr_1.6Sr_0.4NiO₄+xYSZ, were prepared. The composite cathodes with x>0 matched with electrolyte YSZ in thermal expansion coefficient (TEC) better than the cathode Pr_1.6Sr_0.4NiO₄ did. Pr_1.6Sr_0.4NiO₄+20YSZ exhibited the best performance on cathode overpotential and impedance. When the cathode overpotential was 0.1 V, the polarization current density of Pr_1.6Sr_0.4NiO₄+20YSZ was 0.28 A cm^?2, which is about 5.6 times higher than that of Pr_1.6Sr_0.4NiO₄, 0.05 A cm^?2. The area-specific resistance (ASR) for Pr_1.6Sr_0.4NiO₄+20YSZ was about 17.7% of that for Pr_1.6Sr_0.4NiO₄ at 750 °C.     

Oxygen ionic conductivity of La2NiO4+δ via interstitial oxygen defect

The ionic conduction properties of La₂NiO_4+δ were studied from oxygen permeation flux and defect-related transport properties. The effects of the applied oxygen chemical potential gradient and temperature on the oxygen permeability of La₂NiO_4+δ at various thickness are reported. The thermally activated oxygen permeation flux increased monotonically with increasing oxygen chemical potential gradient, yielding a maximum of 0.15 cc min^?1 cm^?2 under air/N₂ conditions for the 0.95 mm-thick La₂NiO_4+δ specimen at 900 °C. The oxygen ion conductivity of La₂NiO_4+δ was calculated as a function of temperature and oxygen partial pressure by differentiating the chemical diffusion equation for the oxygen permeation flux based on the dominant electronic transference number. In addition, the oxygen ion conductivity was extracted successfully by solving the Nernst–Einstein equation combining with the calculated self-diffusion coefficient of oxygen from the chemical diffusivity and thermodynamic enhancement factor from the equilibrium oxygen nonstoichoimetry of a La₂NiO_4+δ specimen, and a deviation of the OPP dependence of 1/6 power was observed.     

Epitaxial growth of well-ordered ultra-thin Al2O3 film on NiAl (1 1 0) by a single-step oxidation

Well-ordered ultra-thin Al₂O₃ films were grown on NiAl (1 1 0) surface by exposing the sample at various oxygen absorption temperatures ranging from 570 to 1100 K at dose rates 6.6 × 10⁻⁵ and 6.6 × 10⁻⁶ Pa. From the results of low-energy electron diffraction (LEED), Auger electron spectrometer (AES) and X-ray photon spectroscopy (XPS) observations, it was revealed that oxidation mechanism above 770 K is different from well-known two-step process. At high temperature, oxidation and crystallization occurred simultaneously while in two-step process oxidation and crystallization occurred one after another. At high-temperature oxidation well-ordered crystalline oxide can be formed by a single-step without annealing. Well-ordered Al₂O₃ layer with thickness over 1 nm was obtained in oxygen absorption temperature 1070 K and a dose rate 6.6 × 10⁻⁶ Pa at 1200 L oxygen.     

Electrical conductivity and oxygen permeation properties of SrCoFeOx membranes

The total conductivity and oxygen permeation properties of dense SrCoFeO_x membranes synthesized from the solid state method were studied in the temperature range of 700–900 °C. The SrCoFeO_x membranes consist of an intergrowth (Sr₄Fe_6 − xCo_xO_13 ± δ), perovskite (SrFe_1 − xCo_xO_3 − δ), and spinel (Co_3 − xFe_xO₄) phase. SrCoFeO_x exhibits n-type and p-type conduction at low and high oxygen partial pressures, respectively, and has a total conductivity of 16.5 S/cm at 900 °C in air. The oxygen permeation fluxes for SrCoFeO_x and SrFeCo_0.5O_x membranes were measured with either an inert or carbon monoxide sweep gas. The oxygen permeation fluxes were higher through SrCoFeO_x membranes than SrFeCo_0.5O_x membranes and can be attributed to a difference in the amount and makeup of the perovskite phase present in each composition. The oxygen permeation fluxes with a carbon monoxide sweep gas were approximately two orders of magnitude larger than the fluxes measured with an inert sweep gas for both compositions. The large oxygen permeation fluxes observed with a carbon monoxide sweep are due to a higher driving force for oxygen transport and a reaction on the sweep side of the membrane that maintains a low oxygen partial pressure.     

A comparative study of the Ruddlesden-Popper series,Lan+1NinO3n+1 (n = 1, 2 and 3), for solid-oxide fuel-cell cathode applications

A comparative investigation of the much-studied La₂NiO_4+δ (n = 1) phase and the higher-order Ruddlesden-Popper phases, La_n+1Ni_nO_3n+1 (n = 2 and 3), has been undertaken to determine their suitability as cathodes for intermediate-temperature solid-oxide fuel cells. As n is increased, a structural phase transition is observed from tetragonal I4/mmm in the hyperstoichiometric La₂NiO_4.15 (n = 1) to orthorhombic Fmmm in the oxygen-deficient phases, La₃Ni₂O_6.95 (n = 2) and La₄Ni₃O_9.78 (n = 3). High temperature d.c. electrical conductivity measurements reveal a dramatic increase in overall values from n = 1, 2 to 3 with metallic behavior observed for La₄Ni₃O_9.78. Impedance spectroscopy measurements on symmetrical cells with La_0.9Sr_0.10Ga_0.80Mg_0.20O_3−δ (LSGM-9182) as the electrolyte show a systematic improvement in the electrode performance from La₂NiO_4.15 to La₄Ni₃O_9.78 with ∼ 1 Ω cm² observed at 1073 K for the latter. Long-term thermal stability tests show no impurity formation when La₃Ni₂O_6.95 and La₄Ni₃O_9.78 are heated at 1123 K for 2 weeks in air, in contrast to previously reported data for La₂NiO_4.15. The relative thermal expansion coefficients of La₃Ni₂O_6.95 and La₄Ni₃O_9.78 were found to be similar at ∼ 13.2 × 10^− 6 K^− 1 from 348 K to 1173 K in air compared to 13.8 × 10^− 6 K^− 1 for La₂NiO_4.15. Taken together, these observations suggest favourable use for the n = 2 and 3 phases as cathodes in intermediate-temperature solid-oxide fuel cells when compared to the much-studied La₂NiO_4+δ (n = 1) phase.     

Oxygen nonstoichiometry and defect equilibrium in La2 − xSrxNiO4 + δ

Nonstoichiometric variation of oxygen content in La_2 ? xSr_xNiO_4 + δ (x = 0, 0.1, 0.2, 0.3, 0.4) and decomposition P(O₂) were determined by means of high temperature gravimetry and coulometric titration. The measurements were carried out in the temperature range between 873 and 1173 K and the P(O₂) range between 10^? 20 and 1 bar. La_2 ? xSr_xNiO_4 + δ showed the oxygen excess and the oxygen deficient compositions depending on P(O₂), temperature, and the Sr content. The value of partial molar enthalpy of oxygen approaches zero as δ increases in the oxygen excess region, which indicate that the interstitial oxygen formation reaction is suppressed as δ increase. The relationship between δ and logP(O₂) were analyzed by two types of defect equilibrium models. One is a localized electron model, and the other is a delocalized electron model. Both models can well explain the oxygen nonstoichiometry of La_2 ? xSr_xNiO_4 + δ with a regular solution approximation.     

Redox behaviour,chemical compatibility and electrochemical performance of Sr2MgMoO6 − δ as SOFC anode

The double perovskite Sr₂MgMoO_6 − δ (SMM) has been proposed as a potential anode material for direct hydrocarbon oxidation in solid oxide fuel cells (SOFCs). The oxygen nonstoichiometry and electrical conductivity dependence of Sr₂MgMoO_6 − δ have been determined as a function of the oxygen partial pressure by coulometric titration and impedance spectroscopy techniques. The chemical compatibility of Sr₂MgMoO_6 − δ with most of the typical electrolytes commonly used in SOFCs i.e. La_0.8Sr_0.2Ga_0.8Mg_0.2O_3 − δ (LSGM), Ce_0.8Gd_0.2O_2 − δ (CGO) and Zr_0.84Y_0.16O_2 − δ (YSZ), was investigated. Reactivity between SMM and all these electrolytes has been found above 1000 °C, although the reaction is most severe with ZrO₂-based electrolytes. Area-specific polarisation resistance of the SMM/LSGM/SMM symmetrical cells indicates that the polarisation resistance increases with the firing temperature of the electrodes due to chemical interaction between LSGM and SMM layers. A CGO buffer layer between the anode and electrolyte was also used to prevent an excessive interdiffusion of ionic species between these components, resulting in better performance. Power densities of 330 and 270 mW cm^− 2 were reached at 800 °C for SMM/CGO/LSGM/LSCF and SMM/LSGM/LSCF electrolyte-supported cells, respectively; with 600-μm-thick LSGM electrolyte, using humidified H₂ as fuel and air as oxidant. XPS and XRPD studies on SMM powders annealed in air and diluted CH₄ atmospheres showed that the surface of SMM powders is mainly formed by SrMoO₄ and metal carbonates.     

Mixed conductivity and electrocatalytic performance of SrFeO3-δ–SrAl2O4 composite membranes

Oxygen-ionic and electronic transport in dense (SrFe)_1−x(SrAl₂)_xO_z composites, consisting of strontium-deficient Sr(Fe,Al)O_3-δ and SrAl₂O₄ phases, is determined by the properties of perovskite-like solid solution. Increasing the content of SrAl₂O₄, with a total conductivity as low as 5 × 10^− 7 −  10^− 5 S × cm^− 1 at 973–1273 K in air, results in the gradual decrease of the partial conductivities, but also enables the suppression of thermal expansion. Compared to single-phase SrFe_1−xAl_xO_3-δ, (SrFe)_1−x(SrAl₂)_xO_z composites exhibit enhanced thermomechanical properties, while the oxygen permeability of these materials has similar values. The composite membranes exhibit stable performance under air/(H₂–H₂O–N₂) and air/(CH₄–He) gradients at 973–1173 K. The oxidation of dry methane by oxygen permeating through (SrFe)_0.7(SrAl₂)_0.3O_z results in dominant total oxidation, suggesting the necessity to incorporate a reforming catalyst into the ceramic reactors for natural gas conversion.     

Mixed conductivity,stability and thermomechanical properties of Ni-doped La(Ga,Mg)O3−δ

Perovskite-type LaGa_0.65Mg_0.15Ni_0.20O_3−δ exhibiting oxygen transport comparable to that in K₂NiF₄-type nickelates was characterized as a model material for ceramic membrane reactors, employing mechanical tests, dilatometry, oxygen permeability and faradaic efficiency measurements, thermogravimetry (TG), and determination of the total conductivity and Seebeck coefficient in the oxygen partial pressure range from 10^− 15 Pa to 40 kPa. Within the phase stability domain which is similar to La₂NiO_4+δ, the defect chemistry of LaGa_0.65Mg_0.15Ni_0.20O_3−δ can be adequately described by the ideal solution model with oxygen vacancies and electron holes to be the only mobile defects, assuming that Ni²⁺ may provide two energetically equivalent sites for hole location. This assumption is in agreement with the density of states, estimated from thermopower, and the coulometric titration and TG data suggesting Ni⁴⁺ formation in air at T < 1150 K. The hole conductivity prevailing under oxidizing conditions occurs via small-polaron mechanism as indicated by relatively low, temperature-activated mobility. The ionic transport increases with vacancy concentration on reducing p(O₂) and becomes dominant at oxygen pressures below 10^− 7–10^− 5 Pa. The average thermal expansion coefficients in air are 11.9 × 10^− 6 and 18.4 × 10^− 6 K^− 1 at 370–850 and 850–1270 K, respectively. The chemical strain of LaGa_0.65Mg_0.15Ni_0.20O_3−δ ceramics at 1073–1123 K, induced by the oxygen partial pressure variations, is substantially lower compared to perovskite ferrites. The flexural strength determined by 3-point and 4-point bending tests is 167–189 MPa at room temperature and 85–97 MPa at 773–1173 K. The mechanical properties are almost independent of temperature and oxygen pressure at p(O₂) = 1–2.1 × 10⁴ Pa and 773–1173 K.     

Synthesis and characterization of (Pr0.75Sr0.25)1 − xCr0.5Mn0.5O3 − δ as anode for SOFCs

The complex perovskite (Pr_0.75Sr_0.25)_1 − xCr_0.5Mn_0.5O_3 − δ (PSCM) has been prepared and studied as possible anode material for high-temperature solid oxide fuel cells (SOFCs). PSCM exhibits GdFeO₃-type structure and is both physically and chemically compatible with the conventional YSZ electrolyte. The reduction of PSCM resulted in structural change from orthorhombic Pbnm to cubic Pm-3m. Selected area electron diffraction (SAED) analysis on the reduced phases indicated the presence of a √2 × √2 × 2 superlattice. The total conductivity values of ∼ 75% dense Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ at 900 °C in air and 5% H₂/Ar are 9.6 and 0.14 S cm^− 1 respectively. The conductivity of PSCM drops with decreasing Po₂ and is a p-type conductor at all studied Po₂. The average TEC of Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ is 9.3 × 10^− 6 K^− 1, in the temperature range of 100–900 °C and is close to that of YSZ electrolyte. The anode polarization resistance of PSCM in wet 5%H₂ is 1.31 Ω cm² at 910 °C and in wet CH₄ at 930 °C; the polarization resistance is 1.29 Ω cm². PSCM was unstable at 900 °C in unhumidified hydrogen. Cell performance measurements carried out using graded PSCM and La_0.8Sr_0.2MnO₃ as anode and cathode respectively yielded a maximum power density of 0.18 W cm^− 2 in wet 5%H₂/Ar at 910 °C and the corresponding current density was 0.44 A cm^− 2 at 0.4 V. The activation energy for the electrochemical cell operating in wet (3% H₂O) 5%H₂/Ar fuel is 85 kJ mol^− 1.     

Transport properties of the Pr2−xSrxNiO4±δ ceramics with x = 0.3 and 0.6

As potential cathode materials Pr_2−xSr_xNiO_4±δ compositions with x = 0.3 and 0.6 were prepared at 1300 °C in air and their electrical conductivity and oxygen non-stoichiometry were investigated in the temperature range 20–1000 °C and oxygen partial pressure (pO₂) 1–21,000 Pa. Sr-doping allows partially to stabilize the Pr₂NiO_4±δ structure, but some phase transitions were observed in spite of that. The electrical conductivity and the oxygen mobility of the Pr- and La-containing ceramic nickelates with K₂NiF₄- type structure are 10–15% higher for Pr_2−xSr_xNiO_4−δ compounds at the same temperature and oxygen partial pressure.     

Ultrasonic assisted-Fenton-like degradation of nitrobenzene at neutral pH using nanosized oxides of Fe and Cu

Ultrasonic-assisted heterogeneous Fenton reaction was used for degradation of nitrobenzene (NB) at neutral pH conditions. Nano-sized oxides of α-Fe₂O₃ and CuO were prepared, characterized and tested in degradation of NB (10 mg L⁻¹) under sonication of 20 kHz at 25 °C. Complete degradation of NB was effected at pH 7 in presence of 10 mM H₂O₂ after 10 min of sonication in presence of α-Fe₂O₃ (1.0 g L⁻¹), (k = 0.58 min⁻¹) and after 25 min in case of CuO (k = 0.126 min⁻¹). α-Fe₂O₃ showed also effective degradation under the conditions of 0.1 g L⁻¹ oxide and 5.0 mM of H₂O₂, even though with a lower rate constant (0.346 min⁻¹). Sonication plays a major role in enhancing the production of hydroxyl radicals in presence of solid oxides. Hydroxyl radicals-degradation pathway is suggested and adopted to explain the differences noted in rate constants recorded on using different oxides.     

Oxygen permeability and stability of Ba0.5Sr0.5Co0.8Fe0.2O3−δ as an oxygen-permeable membrane at high pressures

Oxygen permeation fluxes across the dense Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCFO) membrane disks were measured under an air/helium oxygen partial pressure gradient at high pressures (up to 10 atm) and various temperatures (973–1123 K). The fabricated BSCFO membrane exhibited good oxygen permeability with a high oxygen permeation flux of 2.01 ml min^− 1cm^− 2 (thickness: 1.37 mm) at 1123 K and 10 atm. Oxygen permeation results were analyzed theoretically using the surface exchange current model. The dependences of the oxygen permeation fluxes on the oxygen partial pressure gradient, suggested that the bulk oxygen ionic diffusion was the rate-limiting step for the overall oxygen permeation process across the BSCFO membrane. The ambipolar diffusion coefficients (D_a), the oxygen vacancy diffusion coefficients (D_v) and the oxygen ionic conductivities (σ_i) of the BSCFO material at different temperatures (973–1123 K) were calculated. It was found that BSCFO possessed high oxygen diffusion coefficients and ionic conductivities, which resulted in the good oxygen permeability of BSCFO. In addition, the BSCFO membrane exhibited good stability of oxygen permeation at 1123 K, while the deterioration of oxygen permeation stability was observed at 1098 K due to structural changes occurring at the surface of the BSCFO membrane disk as demonstrated by XRD.     

Ionic and electronic conductivities,stability and thermal expansion of La10 − x(Si,Al)6O26 ± δ solid electrolytes

Apatite-type La_10 − xSi_6 − yAl_yO_{27 − 3x/2 − y/2} (x = 0–0.33; y = 0.5–1.5) exhibit predominant oxygen ionic conductivity in a wide range of oxygen partial pressures. The conductivity of silicates containing 26.50–26.75 oxygen atoms per formula unit is comparable to that of gadolinia-doped ceria at 770–870 K. The average thermal expansion coefficients are (8.7–10.8) × 10^− 6 K^− 1 at 373–1273 K. At temperatures above 1100 K, silicon oxide volatilization from the surface layers of apatite ceramics and a moderate degradation of the ionic transport with time are observed under reducing conditions, thus limiting the operation temperature of Si-containing solid electrolytes.     

Oxygen diffusion and surface exchange studies on (La0.75Sr0.25)0.95Cr0.5Mn0.5O3−δ

Oxygen tracer diffusion coefficient (D^⁎) and surface exchange coefficient (k^⁎) have been measured for (La_0.75Sr_0.25)_0.95Cr_0.5Mn_0.5O_3−δ using isotopic exchange and depth profiling by secondary ion mass spectrometry technique as a function of temperature (700–1000 °C) in dry oxygen and in a water vapour-forming gas mixture. The typical values of D^⁎ under oxidising and reducing conditions at ∼ 1000 °C are 4 × 10^− 10 cm² s^− 1 and 3 × 10^− 8 cm² s^− 1 respectively, whereas the values of k^⁎ under oxidising and reducing conditions at ∼ 1000 °C are 5 × 10^− 8 cm s^− 1 and 4 × 10^− 8 cm s^− 1 respectively. The apparent activation energies for D^⁎ in oxidising and reducing conditions are 0.8 eV and 1.9 eV respectively.     

Phase stability and oxygen non-stoichiometry of SrCo0.8Fe0.2O3−δ measured by in situ neutron diffraction

The phase stability, oxygen stoichiometry and expansion properties of SrCo_0.8Fe_0.2O_3−δ (SCF) were determined by in situ neutron diffraction between 873 and 1173 K and oxygen partial pressures of 5 × 10^− 4 to 1 atm. At a pO₂ of 1 atm, SCF adopts a cubic perovskite structure, space group Pm3¯m, across the whole temperature range investigated. At a pO₂ of 10^− 1 atm, a two-phase region exists below 922 K, where the cubic perovskite phase coexists with a vacancy ordered brownmillerite phase, Sr₂Co_1.6Fe_0.4O₅, space group Icmm. A pure brownmillerite phase is present at pO₂ of 10^− 2 and 5 × 10^− 4 atm below 1020 K. Above 1020 K, the brownmillerite phase transforms to cubic perovskite through a two-phase region with no brownmillerite structure observed above 1064 K. Large distortion of the BO₆ (B = Co, Fe) octahedra is present in the brownmillerite structure with apical bond lengths of 2.2974(4) Å and equatorial bond lengths of 1.9737(3) Å at 1021 K and a pO₂ of 10^− 2 atm. SCF is highly oxygen deficient with a maximum oxygen stoichiometry, 3 − δ, measured in this study of 2.58(2) at 873 K and a pO₂ of 1 atm and a minimum of 2.33(2) at 1173 K and a pO₂ of 5 × 10^− 4 atm. Significant differences in lattice volume and expansion behavior between the brownmillerite and cubic perovskite phases suggest potential difficulties in thermal cycling of SrCo_0.8Fe_0.2O_3−δ membranes.     

Ionic conductivity of brownmillerite-type calcium ferrite under oxidizing conditions

The thermogravimetric and Mössbauer spectroscopy studies showed that, at atmospheric oxygen pressure, the oxygen content in Ca₂Fe₂O₅ brownmillerite is very close to stoichiometric at 300–1270 K. The orthorhombic lattice of calcium ferrite undergoes a transition from primitive (space group Pnma) to body-centered (I2mb) at 950–1000 K, which is accompanied with decreasing thermal expansion coefficient (TEC) and increasing activation energy for the total conductivity, predominantly p-type electronic. The steady-state oxygen permeation through dense Ca₂Fe₂O₅ ceramics is limited by the bulk ionic conduction. The ion transference numbers in air vary in the range 0.002–0.007 at 1123–1273 K, increasing with temperature. Analysis of stereological factors, which may affect oxygen diffusivity, suggests a dominant role of the ion jumps along octahedral and, possibly, tetrahedral layers of the brownmillerite structure. The ionic conductivity of calcium ferrite is higher than that of Ca₂FeAlO_5+δ, but lower compared to the oxygen-deficient perovskite phases based on SrFeO_3−δ where the diffusion pathways form a three-dimensional network. The average TECs of Ca₂Fe₂O₅ ceramics, calculated from dilatometric data in air, are 13.1 × 10^− 6 K^− 1 at 370–950 K and 11.3 × 10^− 6 K^− 1 at 970–1270 K.     

Shock tube/laser absorption studies of the decomposition of methyl formate

Reaction rate coefficients for the major high-temperature methyl formate (MF, CH₃OCHO) decomposition pathways, MF → CH₃OH + CO (1), MF → CH₂O + CH₂O (2), and MF → CH₄ + CO₂ (3), were directly measured in a shock tube using laser absorption of CO (4.6 μm), CH₂O (306 nm) and CH₄ (3.4 μm). Experimental conditions ranged from 1202 to 1607 K and 1.36 to 1.72 atm, with mixtures varying in initial fuel concentration from 0.1% to 3% MF diluted in argon. The decomposition rate coefficients were determined by monitoring the formation rate of each target species immediately behind the reflected shock waves and modeling the species time-histories with a detailed kinetic mechanism [12]. The three measured rate coefficients can be well-described using two-parameter Arrhenius expressions over the temperature range in the present study: k₁ = 1.1 × 10¹³ exp(?29556/T, K) s^?1, k₂ = 2.6 × 10¹² exp(?32052/T, K) s^?1, and k₃ = 4.4 × 10¹¹ exp(?29 078/T, K) s^?1, all thought to be near their high-pressure limits. Uncertainties in the k₁, k₂ and k₃ measurements were estimated to be ±25%, ±35%, and ±40%, respectively. We believe that these are the first direct high-temperature rate measurements for MF decomposition and all are in excellent agreement with the Dooley et al. [12] mechanism. In addition, by also monitoring methanol (CH₃OH) and MF concentration histories using a tunable CO₂ gas laser operating at 9.67 and 9.23 μm, respectively, all the major oxygen-carrying molecules were quantitatively detected in the reaction system. An oxygen balance analysis during MF decomposition shows that the multi-wavelength laser absorption strategy used in this study was able to track more than 97% of the initial oxygen atoms in the fuel.