Conductivity and thermal studies of blend polymer electrolytes based on PVAc–PMMA

The polymer electrolytes comprising blend of poly(vinyl acetate) (PVAc) and poly(methylmethacrylate) (PMMA) as a host polymer and LiClO₄ as a dopant are prepared by solution casting technique. The amorphous nature of the polymer–salt complex has been confirmed by XRD analysis. The DSC thermograms show two T_g's for PVAc–PMMA blend. A decrease in T_g with the LiClO₄ content reveals the increase of segmental motion. Conductance spectra results are found to obey the Jonscher's power law and the maximum dc conductivity value is found to be 1.76 × 10^− 3 S cm^− 1 at 303 K for the blend polymer complex with 20 wt.% LiClO₄, which is suitable for the Li rechargeable batteries. The conductivity–temperature plots are found to follow an Arrhenius nature. The dc conductivity is found to increase with increase of salt concentration in the blend polymer complexes.     

Study on ionic conductivity of polymer electrolyte plasticized with PEG–aluminate ester for rechargeable lithium ion battery

We have synthesized poly(ethylene glycol) (PEG)-aluminate ester as a plasticizer for solid polymer electrolytes. The thermal stability, ionic conductivity and electrochemical stability of the polymer electrolyte which consist of poly(ethylene oxide) (PEO)-based copolymer, PEG–aluminate ester and lithium bis-trifluoromethanesulfonimide (LiTFSI) were investigated. Addition of PEG–aluminate ester increased the ionic conductivity of the polymer electrolyte, showing greater than 10^− 4 S cm^− 1 at 30 °C. The polymer electrolyte containing PEG–aluminate ester retained thermal stability of the non-additive polymer electrolyte and exhibited electrochemical stability up to 4.5 V vs. Li⁺/Li at 30 °C.     

Preparation of poly(vinyl phosphate-b-styrene) copolymers and its blend with PPO as proton exchange membrane for DMFC applications

Poly(vinyl phosphate-b-styrene) (poly(VPP-b-St)) block copolymers were prepared via consecutive telomerization of vinyl acetate (VAc), atom transfer radical polymerization (ATRP) with styrene, saponification, and phosphorylation with phosphorus oxychloride. The resulting block copolymers were characterized by FT-IR and pH titration. Then, the block copolymers were blended with poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) to prepare direct methanol fuel cell (DMFC) membrane. The performance of poly(VPP-b-St)/PPO blend membranes was measured in terms of proton conductivity, methanol permeability, thermal and hydrolytic stability. The proton conductivities were in the range of 10^− 4 to 10^− 2 S/cm (60 °C, RH = 95%); the methanol permeabilities were in the range of 4.14 × 10^− 8 to 9.62 × 10^− 8 cm²/s (25 °C), and quite lower than that of Nafion® 117. Also, the thermal stability of the blend membranes was characterized by TGA, and was stable up to 400 °C; the blend membranes had better hydrolytic stability.     

Effect of amphiphilic hyperbranched-star polymer on the structure and properties of PVDF based porous polymer electrolytes

An amphiphilic hyperbranched-star polymer (HPE-g-MPEG) was synthesized by grafting methoxy poly(ethylene glycol) to the end of the hyperbranched polyester (HPE) molecule using terephthaloyl chloride (TPC) as the coupling agent. The synthesized amphiphilic hyperbranched-star polymer was blended with poly(vinylidene fluoride) (PVDF) to fabricate porous membranes via typical phase inversion process, and then the membranes were filled and swollen by a liquid electrolyte solution to form polymer electrolytes. The influences of HPE-g-MPEG on the morphology, crystallinity, liquid electrolyte uptake, mechanical properties of the porous membranes and the electrochemical properties of the activated membranes were investigated. It was found that the addition of HPE-g-MPEG resulted in a significant increase in porosity and a considerable reduction in crystallinity of the blend membranes, which favored the liquid electrolyte uptake and, consequently, led to a remarkable increase in ion conductivity at ambient temperature. The maximum ion conductivity observed in this study was 1.76 × 10^? 3 S/cm at 20 °C for the blend membrane with a HPE-g-MPEG/PVDF ratio of 3/10 (w/w).     

Facile preparation and characterization of hollow poly(St-co-MMA-co-BA-co-MAA) core–double shell latex nanoparticles for electrophoretic displays

Novel core–double shell particles with poly(methyl methacrylate-co-butyl acrylate) (PMMA-co-BA) as the cores, poly(methyl methacrylate-co-butyl acrylate-co-methacrylic acid) (PMMA-co-BA-co-MAA) as the inner shells, poly(styrene-co-methyl methacrylate) (PS-co-MMA) as the outer shells were prepared by soap-free emulsion polymerization. The acid–alkali osmotic swelling processes were made before the outer shells wrapped for bigger aperture. The optimal experiment conditions were summarized. The morphology and size of the hollow latex particles were observed by transmission electron microscopy. The results showed that the uniform sizes of the hollow latex particles were about 230 nm. The electrophoretic mobility of them in tetrachloroethylene was 0.91 × 10⁻¹⁰ m² V⁻¹ s⁻¹, and the Zeta-potential was 5.87 mV. The results showed that the hollow polymer particles can used as background particles.     

Single ion conductors—polyphosphazenes with sulfonimide functional groups

A novel single ion conductive polymer electrolyte was developed by covalently linking an arylsulfonimide substituent to the polyphosphazene backbone. Polymeric single-ion conductors incorporate the anion of a salt either into the polymer backbone or as a pendent group linked to the polymer backbone. Immobilization of the anion could provide access to electrochemical devices that would be less vulnerable to increased resistance associated with salt concentration gradients at the interfaces during charging and discharging. In this work, an immobilized sulfonimide lithium salt is the source of lithium cations, while a cation-solvating cosubstituent, 2-(2-methoxyethoxy)ethoxy, was used to increase free volume and assist cation transport. The ionic conductivities showed a dependence on the percentage of lithiated sulfonimide substituent present. Increasing amounts of the lithium sulfonimide component increased the charge carrier concentration but decreased the ionic conductivity due to decreased macromolecular motion and possible increased shielding of the nitrogen atoms in the polyphosphazene backbone. Maximum ionic conductivity values of 2.45 × 10^− 6 S/cm at ambient temperature and 4.99 × 10^− 5 S/cm at 80 °C were obtained. Gel polymer electrolytes containing N-methyl-2-pyrrolidone gave ionic conductivities in the 10^− 3 S/cm range. The ion conduction process was investigated through model polymers that contained the non-immobilized sulfonimide — systems that had higher conductivities than their single ion counterparts.     

High ionic conductive behavior of cyanoethylated polyvinylalcohol- and polyacrylonitrile-based electrolytes

New type polymer electrolyte films based on poly(acrylonitrile), (PAN), and cyanoethylated poly(vinyl alcohol), (CN-PVA), were prepared and their conducting behaviors were investigated. CN-PVA was prepared from poly(vinyl alcohol), (PVA) and acrylonitrile in the presence of sodium hydroxide and quaternary ammonium halide as a phase transfer catalyst. Free standing PAN- and CN-PVA-based electrolyte films were prepared by casting the propylene carbonate (PC) solution containing PAN, CN-PVA and LiClO₄ and removing some amount of PC. Ionic conductivity of the electrolyte film, (PAN)10(CN-PVA) 10(LiClO₄)8(PC)4 composite film was 14.6 mS cm^− 1 at 30 °C and 22.4 mS cm^− 1 at 60 °C. FTIR results for the electrolyte films suggest that the nitrile groups in the CN-PVA matrix mainly interact with the lithium ions in the films and enhance dissolution of the lithium salt in the electrolyte films.     

Study of EVOH based single ion polymer electrolyte: Composition and microstructure effects on the proton conductivity

A comb-like EVOH based single ion polymer electrolyte (EVOH-g-SPEG) was synthesized by sulfonification of EVOH grafts 2-(2-chloroethoxy) ethanol (C₄H₉O₂Cl)/2-[2-(2-chloroethxy) ethoxy] ethanol (C₆H₁₃O₃Cl) with 1, 3-propane sultone. The main chain of the comb-like polymer is hydrophobic polyethylene segments; the side chain is hydrophilic poly (ethylene glycol) (PEG) segment, which can solubilize large amounts of inorganic salts. The sulfonic acid group was introduced onto the end of the PEG side chain. The acid form of SPE was successfully obtained by being dialyzed from the products with acid solution. The saturation water sorption of EVOH-g-SPEG membrane increased with the side chain length and the immersion time. The XRD results indicate that the water in SPE membrane region can destroy the membrane crystalline structure and the water absorption membranes are nearly amorphous. AFM phase images of the hydration membranes clearly show the hydrophilic domains, with sizes increasing from 10 to 35 nm as a function of the side chain length. A phase inversion could be observed when n ≥ 5, which was consistent with a rapid increase in water absorption. And the ion conductivity is also measured by AC impedance. The conductivity is greatly influenced by ion exchange capacity and water sorption. The comb-like EVOH-g-SPEG polymer electrolyte grafts with 2 PEG side chain provides the highest ionic conductivity (1.65 × 10^− 3 S cm^− 1). The comb-like polymer could be a candidate as new polymeric electrolyte material for fuel cells and other electrochemical devices.     

Investigation of ionic conduction and mechanical properties of PMMA–PVdF blend-based polymer electrolytes

Polymeric gel electrolytes, based on a blend of poly(methylmethacrylate)/poly(vinylidene fluoride) (PMMA/PVdF), ethylene carbonate/propylene carbonate (EC/PC) as plasticizer and lithium perchlorate as electrolyte, have been studied as a function of the different polymeric ratios to obtain the best compromise between ionic conduction and mechanical properties of the systems involved. Ionic conductivity and the lithium self-diffusion coefficient were measured by the PFG–NMR method, which revealed a maximum of lithium mobility for the composition PMMA 60%–PVdF 40%. The Raman spectroscopic study revealed a change of the interaction between that of the lithium cations and the plasticizer molecules for different PMMA / PVdF ratios. Oscillatory rheological tests have shown better mechanical properties for the intermediate compositions of the blend.     

Effects of plasticizer and nanofiller on the dielectric dispersion and relaxation behaviour of polymer blend based solid polymer electrolytes

Solid polymer electrolytes consisted of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) blend (50:50 wt/wt%) with lithium triflate (LiCF₃SO₃) as a dopant ionic salt at stoichiometric ratio [EO + (CO)]:Li⁺ = 9:1, poly(ethylene glycol) (PEG) as plasticizer (10 wt%) and montmorillonite (MMT) clay as nanofiller (3 wt%) have been prepared by solution cast followed by melt–pressing method. The X–ray diffraction study infers that the (PEO–PMMA)–LiCF₃SO₃ electrolyte is predominantly amorphous, but (PEO–PMMA)–LiCF₃SO₃–10 wt% PEG electrolyte has some PEO crystalline cluster, whereas (PEO–PMMA)–LiCF₃SO₃–10 wt% PEG–3 wt% MMT electrolyte is an amorphous with intercalated and exfoliated MMT structures. The complex dielectric function, ac electrical conductivity, electric modulus and impedance spectra of these electrolytes have been investigated over the frequency range 20 Hz to 1 MHz. These spectra have been analysed in terms of the contribution of electrode polarization phenomenon in the low frequency region and the dynamics of cations coordinated polymer chain segments in the high frequency region, and also their variation on the addition of PEG and MMT in the electrolytes. The temperature dependent dc ionic conductivity, dielectric relaxation time and dielectric strength of the plasticized nanocomposite electrolyte obey the Arrhenius behaviour. The mechanism of ions transportation and the dependence of ionic conductivity on the segmental motion of polymer chain, dielectric strength, and amorphicity of these electrolytes have been explored. The room temperature ionic conductivity values of the electrolytes are found ∼10⁻⁵ S cm⁻¹, confirming their use in preparation of all-solid-state ion conducting devices.     

Infrared spectroscopic and conductivity studies of poly(N-methylpropylenimine)/lithium triflate electrolytes

Poly(propylenimine), PPI, was methylated using Eschweiler-Clark conditions to produce poly(N-methylpropylenimine), PMPI. Differences may be seen in the IR spectra of the PMPI (–CH₂CH₂CH₂NCH₃–) and its homolog poly(N-methylethylenimine), PMEI, (–CH₂CH₂NCH₃–), especially in the conformation region (~ 1100 to ~ 1400 cm^− 1). The addition of lithium trifluoromethanesulfonate, (LiCF₃SO₃), sharpens the distinctions between these systems. Comparison of IR spectra of polymer:LiCF₃SO₃ complexes at compositions ranging from pure polymer to 5:1 N:Li⁺ (molar ratio) suggests significant differences in the nature of polymer salt interactions and the complex structure present in each system. These are further evidenced by differential scanning calorimetry data in which PMPI displays less variation in glass transition temperature, T_g, with the addition of salt than seen in PMEI. These observations may be interpreted in terms of local structural changes originating in cation–anion and cation–polymer interactions, particularly at mid to high salt concentrations.     

Poly(ethyleneglycol methacrylate phosphate) and heterocycle based proton conducting composite materials

Novel anhydrous proton conducting polymer electrolytes based on poly(ethyleneglycol methacrylate phosphate) (PEGMAP) and heterocycle have been investigated. The materials were synthesized via conventional radical bulk polymerization of ethylene glycol methacrylate phosphate in the presence of proton solvents such as imidazole (Im) or benzimidazole (BnIm). The poly(EGMAP–Im_x) or poly(EGMAP–BnIm_x) composites were produced where x is the molar ratio of heterocycle to monomer in the feed. The polymer–heterocycle electrolytes were characterized by elemental analysis (EA), FT-IR spectroscopy, thermogravimetry analysis (TG), differential scanning calorimetry (DSC) and impedance spectroscopy. Maximum proton conductivity of 2 × 10^− 4 S/cm has been obtained for the anhydrous composite electrolytes at 160 °C.     

Third order nonlinear optical properties of ethyltriphenylphosphonium bis(2-thioxo-1,3-dithiole-4,5-dithiolato)aurate (III)

A novel organometallic compound, ethyltriphenylphosphonium bis(2-thioxo-1,3-dithiole-4,5-dithiolato)aurate (III), abbreviated as TPEPADT, was synthesized. The TPEPADT doped poly(methyl methacrylate) (PMMA) thin film with a mass fraction of 1% (1 wt.%) was prepared by using a spin-coating method. The third-order nonlinear optical properties of TPEPADT in acetonitrile solution and TPEPADT-doped PMMA thin film were investigated by using the laser Z-scan technique at the wavelength 1064 nm with laser duration of 20 ps. The linear refractive index of the polymer thin film was also studied. The Z-scan curves revealed that both TPEPADT in acetonitrile solution and the polymer thin film possessed negative nonlinear refraction, exhibiting a self-defocusing effect and nonlinear absorption was negligible under the experimental conditions used. The nonlinear refractive index was calculated to be ?1.9 × 10^?18 m²/W for TPEPADT in acetonitrile solution and ?8.9 × 10^?15 m²/W for the polymer thin film. These results suggest that TPEPADT have potential for the application of all-optical switching devices.     

Synthesis and ionic conductivity of polymeric ion gel containing room temperature ionic liquid and phosphotungstic acid

Composite electrolyte comprising phosphotungstic acid (PWA) filler and 1-butyl-3-methyl-imidazolium-tetrafluoroborate (BMImBF₄) room temperature ionic liquid (RTIL) in poly(2-hydroxyethyl methacrylate) (PHEMA) matrix has been prepared. The polymer matrix was formed by free radical polymerization of 2-hydroxyethyl methacrylate (HEMA) monomers. BMImBF₄ was used as both ionic source and plasticizer, and PWA filler provided the proton conductivity in this system. The interactions and structure changes of the PHEMA-RTIL-PWA composites were investigated by Fourier transform infrared spectra, differential scanning calorimetry, and X-ray diffraction. PWA fillers maintained their Keggin structure within a limited range and enhanced the ionic conductivity of the composite electrolyte. The electrolyte with PWA at the 2 wt.% showed the highest ionic conductivity of 8 × 10^− 4 S cm^− 1 at room temperature and 96% relative humidity.     

Ionic conductivity of polymer electrolyte membranes based on polyphosphazene with oligo(propylene oxide) side chains

A polyphosphazene [NP(NHR)₂]_n with oligo[propylene oxide] side chains − R = –[CH(CH₃)–CH₂O]_m–CH₃ (m = 6 – 10) was synthesized by living cationic polymerisation and polymer-analogue substitution of chlorine from the intermediate precursor [NPCl₂]_n using the corresponding primary amine RNH₂. The polymer had an average molecular weight of 3.3 × 10⁵ D. Polymer electrolytes with different concentrations of dissolved lithium triflate (LiCF₃SO₃) were prepared. Mechanically stable polymer electrolyte membranes were formed using UV radiation induced crosslinking of the polymer salt mixture in the presence of benzophenone as photoinitiator. The glass transition temperature of the parent polymer was found to be − 75 °C before cross linking. It increases after crosslinking and with increasing amounts of salt to a maximum of − 55 °C for 20 wt.% LiCF₃SO₃. The ionic conductivity was determined by impedance spectroscopy in the temperature range 0–80 °C. The highest conductivity was found for a salt concentration of 20 wt.% LiCF₃SO₃: 6.5 × 10^− 6 S·cm^− 1 at 20 °C and 2.8 × 10^− 4 S cm^− 1 at 80 °C. The temperature dependence of the conductivities was well described by the MIGRATION concept.     

Preparation and characterization of solid polymer electrolytes based on PHEMO and PVDF-HFP

Polymer electrolyte membranes consisting of a novel hyperbranched polyether PHEMO (poly(3-{2-[2-(2-hydroxyethoxy) ethoxy] ethoxy}methyl-3′-methyloxetane)), PVDF-HFP (poly(vinylidene fluoride-hexafluoropropylene)) and LiTFSI have been prepared by solution casting technique. X-ray diffraction of the PHEMO/PVDF-HFP polymer matrix and pure PVDF-HFP revealed the difference in crystallinity between them. The effect of different amounts of PVDF-HFP and lithium salts on the conductivity of the polymer electrolytes was studied. The ionic conductivity of the prepared polymer electrolytes can reach 1.64 × 10^? 4 S·cm^? 1 at 30 °C and 1.75 × 10^? 3 S·cm^? 1 at 80 °C. Thermogravimetric analysis informed that the PHEMO/PVDF-HFP matrix exhibited good thermal stability with a decomposition temperature higher than 400 °C. The electrochemical experiments showed that the electrochemical window of the polymer electrolyte was around 4.2 V vs. Li⁺/Li. The PHEMO/PVDF-HFP polymer electrolyte, which has good electrochemical stability and thermal stability, could be a promising solid polymer electrolyte for polymer lithium ion batteries.     

Sulphur dioxide plasma modification on poly(methyl methacrylate) for fluidic devices

We developed a sulphur dioxide plasma modification on a poly(methyl methacrylate) (PMMA) material for fluidic electrophoresis devices. The inner surface of the PMMA channel of a chip was modified by using sulphur dioxide plasma treatment. Contact angle measurements indicated that the buffer solutions were able to fill the capillary because of the hydrophilic property of the internal surface of the chip. XPS analysis indicated that the sulphur dioxide plasma treatment introduced a negative charge originating from the dissociation of the hydrogen atoms of sulphonic groups. Since this introduced a negative charge originating from strong acid sulphonic groups onto the surface of the channel, the electroosmotic flow (EOF) was observed to be large (∼7 × 10⁻⁴ m² V⁻¹ s⁻¹) and stable over a wide range of pH (4–10). The chip was fabricated by using plastic injection moulding methods for enabling the mass fabrication and disposable use of chips. The separation method is based on the net electric charge of the material, which enables the separation of identical samples on the basis of both isoelectric points and molecular weight. Two synthetic peptides with similar isoelectric points and molecular weights but different net charges were selected as model protein samples for the separation. The sample peptides were detected under fluorescence microscopy. The resulting electropherograms obtained by using the sulphur dioxide plasma-treated PMMA chip demonstrated that the two peptides were separated and that the migration time of the peptides was correlated with the net charge.     

Polymer electrolytes based on cross-linked cyclotriphosphazenes

Substituted cyclotriphosphazenes were used to prepare lithium ion conducting polymer networks. Two types of compounds were synthesized starting with the precursor hexachlorocyclotriphosphazene (HCCP): Type I (CVEEP) in which all the chlorine atoms in HCCP were replaced by vinyloxyethoxyethoxy groups (VEE = –OCH₂CH₂OCH₂CH₂OCHCH₂), and type II (CVMEEP) in which half of the chlorine was replaced by VEE and the other half by methoxyethoxyethoxy groups (MEE = –OCH₂CH₂OCH₂CH₂OCH₃). The terminal vinyl groups were used to build up a network by a thermally initiated cross-linking of lithium salt containing membranes. Polymer electrolytes with dissolved LiSO₃CF₃ and LiN(SO₂CF₃)₂ were investigated by impedance measurements. The ionic conductivity of CVMEEP with 10 wt.% LiSO₃CF₃ was 3.2 × 10^− 5 S/cm at 30 °C and 4.1 × 10^− 4 S/cm at 90 °C. Lower conductivity values in the range 10^− 8–10^− 9 S/cm were obtained at 30 °C for the highly crosslinked CVEEP. An interesting polymer electrolyte with good mechanical properties and a good conductivity of 1.3 × 10^− 5 S/cm (30 °C) was obtained from a solution of MEEP (= poly[bis(methoxy–ethoxy–ethoxy)phosphazene]) and LiSO₃CF₃ in CVEEP as an interpenetrating network.     

Synthesis and properties of a new class of fluorine-containing dilithium salts for lithium-ion batteries

A facile synthetic route for the development of a new class of dilithium salts is described. Because of the presence of two lithium ions per molecule, these salts require lower concentrations than commonly used salts to achieve comparable ionic conductivities at ambient temperatures. An ionic conductivity of 3.55 × 10^− 3 S/cm at 30 °C was obtained using 0.5 M salt solution in 1:1 wt/wt ethylene carbonate:dimethyl carbonate. The salts exhibit excellent thermal stabilities to at least 350 °C and are electrochemically stable below 4.2 V versus lithium metal. The best salt was tested with a polymer electrolyte system. Incorporation of a polyethylene glycol-based borate ester plasticizer improved the ionic conductivity of the solid polymer electrolyte film up to 1.36 × 10^− 5 S/cm at 30 °C, which is 10 times higher than that of un-plasticized electrolyte films.     

Polymer electrolytes based on poly(vinylidene fluoride-co-hexafluoropropylene) with crosslinked poly(ethylene glycol) for lithium batteries

The combination of a poly(ethylene glycol) (PEG) network and poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) copolymer chains is one of the most efficient means for modifying PVDF-HFP gel electrolytes. Previous preparations tend to introduce contamination into the polymer gel electrolyte because of irradiation, high temperature or the initiator needed for crosslinking which might result in the electrochemical degradation. In order to overcome the above disadvantages, a new method has been developed to successfully prepare the semi-interpenetrating polymer networks of PVDF-HFP based electrolytes with crosslinked diepoxy polyethylene glycol (DIEPEG). In this process, impurities are avoided because of a moderate reaction temperature at 50 °C and poly(ethylenimine) (PEI) as the crosslinking agent. Microporous films with various compositions are prepared and characterized. Thermal, mechanical, swelling and electrochemical properties, as well as microstructures of the prepared polymer electrolytes have been investigated using thermogravimetric analysis, electrochemical impedance spectroscopy, linear sweep voltammetry, and scanning electron microscopy. The results show that the blend polymer electrolyte with PVDF-HFP/PEI + DIEPEG (60:40 w/w) has an ionic conductivity of 2.3 mS cm^? 1 at room temperature in the presence of 1 M LiPF₆ in EC and DMC (1:1 w/w). All the blend electrolytes are electrochemically stable up to 4.8 V versus Li/Li⁺. The results reveal that this new method may be very promising for improving PVDF-HFP based electrolytes.