Surface relaxation of Ni(110) investigated by high energy ion scattering

The surface relaxation of Ni(110) has been investigated with High Energy Ion Scattering (HEIS). The results indicate significant displacements of at least two surface layers, corresponding to a contraction of 4.8 ± 1.7% in the first interlayer distance, followed by an expansion of 2.4 ± 1.2%.     

Angular resolved Auger emission from clean and sulfur covered Ni(110) surface

The angular dependence of the nickel M₂₃VV and of the sulfur L₂₃VV Auger transitions are studied in detail, on clean and sulfur covered Ni(110) surfaces. New experimental data are presented for the anisotropy of both transitions as a function of polar and azimuthai angles of emission. Our model, which incorporates at the same time the multiple scattering effects in the final state wave function and the intrinsic anisotropy of the Auger emitter, is found to give a satisfactory account of the observed auger anisotropy. We find a large sensitivity to the position of the sulfur adsorbed atoms. The best agreement is obtained for the hollow site. slightly less than 0.9 Å above the top nickel layer. This conclusion is consistent with previous LEED and MEIS studies, but does not agree with the long bridge site obtained from quantum chemistry calculations. Moreover the sulfur emitter on this particular Ni(110) face appears to have an intrinsic anisotropy.     

Relationship between vibrational states of O-Ni systems and their superficial structure on (100) face of nickel single crystal

High resolution energy loss spectra of 4 eV electrons reflected in the specular direction from Ni(100) surface clean or covered by the ordered structures obtained in the different stages of the metal oxidation, are analysed with reference to LEED patterns. At room temperature, the successive p(2 × 2) and c(2 × 2) structures associated with the chemisorption of oxygen have been observed without modification of the energy loss spectra, in respect of the clean nickel surface. Surface phonons are known to occur in the case of the c(2 × 2)S ordered layer and their absence in the case of Ni-O corresponding system is discussed. After short exposures to oxygen between 200 to 500° C, the surface exhibits a so called “intermediate oxide”. It is identified by its hexagonal unit mesh (～5 Å) with two equivalent orientations along the [100] and [110] directions of the substrate and its vibrational spectra characterized by a loss peak at ? 112.5 meV (± 2.5 meV). Subsequent exposures to oxygen lead to the formation of the (100) face of NiO (in epitaxy on the Ni(100) face) accurately identified by its LEED pattern. The obtained typical multiple loss spectra with spacing 67.5 meV (± 15 meV) reveal a scattering of low energy electrons by long wavelength optical phonons associated to the oxide. The characteristic energy loss (67.5 meV) is in relative good agreement with the energy of the Fuchs-Kliewer surface phonon calculated from the optical constants of the nickel oxide.     

The geometrical and vibrational properties of the Rh(111) surface

Low-energy electron diffraction (LEED) data have been used to characterize the clean Rh(111) surface. The surface geometry, the degree of surface relaxation, and the Debye temperature have been determined. In the Debye temperature measurement, specular LEED beam intensities were monitored as a function of temperature over a range of electron energies from approximately 30 to 1000 eV. It was found that the bulk Debye temperature is 380 ± 23 K, and the normal component of the Debye temperature at the lowest electron energy used is 197 ± 12 K. The Rh(111) surface relaxation has been determined both by a convolution-transform analysis and by dynamical calculations. Within experimental error, neither expansion nor contraction of the topmost layer has been detected. The results of the convolution-transform analysis of specular beams at two angles of incidence and of a nonspecular beam at normal incidence suggest an expansion of the topmost layer of 3 ± 5% of the bulk layer spacing. In agreement with this, comparisons between the results of the dynamical calculation and experimental data for five nonspecular beams at normal incidence suggest that the surface layer relaxes by 0 ± 5%. In addition, the dynamical calculations indicate that the topmost layer maintains an fcc structure.     

The effect of oxygen coverage on surface relaxation of Ni(110) measured by medium energy ion scattering

Changes have been observed in the upper layer spacing of a clean and an oxygen covered Ni(110) single crystal by employing medium energy ion scattering, combined with channeling and blocking. We find a contraction of 4% for the clean surface and a minor expansion of 1% for a surface with $\text{1}\text{3}$ monolayer of adsorbed oxygen.     

Helium scattering from metal surfaces: potential determination and crystallography

We describe a method for determining the interaction potential between a helium atom and a metal surface from diffraction data. Results are presented for He/Ni(110) and He/Cu(110). For He/Cu(110) the potential 3s in good agreement with a first principles calculation but this is not true for He/Ni(110). We also show that a surface relaxation of 10% produces measurable changes in intensities.     

Hydrogen chemisorption on Ni(110) by high-resolution electron energy loss spectroscopy

High-resolution electron energy loss spectra of hydrogen-covered Ni(110) surfaces both at 100 and 300 K are presented. The adsorbed sites of hydrogen atoms are discussed.High-resolution electron energy loss spectra of hydrogen covered Ni(110) surfaces have been studied. Tentative models for the adsorbed sites of hydrogen atoms are as follows: (1) For the (2 × 1)-H surface, hydrogen is adsorbed in the three-coordinated sites of the rudimentary (111) face of the unreconstructed Ni(110) substrate. (2) For the low-temperature (1 × 2)-H surface, hydrogen is adsorbed in the three-coordinated sites and, probably, in the two-fold hollow sites of the distorted Ni(110) substrate. (3) For the room-temperature (1 × 2)-H surface, hydrogen is disorderedly adsorbed in the three-coordinated, two-fold hollow and short-bridge sites and, possibly, in the octahedral sites of the distorted Ni(110) substrate. Some of the unresolved problems in the above assignments are summarized: (1) Strictly, the three-coordinated sites above are somewhat different from those discussed in the molecular-beam diffraction study [5]. (2) For the low-temperature (1 × 2)-H surface, the loss associated with hydrogen in the two-fold hollow sites is apparently not observed. (3) Intensity changes of the three losses for the room-temperature (1 × 2)-H surface with increasing hydrogen pressure (Fig. 2) are not well understood.     

Structural, electronic and magnetic properties of the Mnben Ni(110) c(2×2) surface alloy

Using first-principles total energy method, we study the structural, the electronic and the magnetic properties of the MnNi(110) c(2×2) surface alloy. Paramagnetic, ferromagnetic, and antiferromagnetic surfaces in the top layer and the second layer are considered. It turns out that the substitutional alloy in the outermost layer with ferromagnetic surface is the most stable in all cases. The buckling of the Mn–Ni(110) c(2×2) surface alloy in the top layer is as large as 0.26á(1á=0.1 n13) and the weak rippling is 0.038 AA in the third layer, in excellent agreement with experimental results. It is proved that the magnetism of Mn can stabilize this surface alloy. Electronic structures show a large magnetic splitting for the Mn atom, which is slightly higher than that of Mn–Ni(100) c(2×2) surface alloy (3.41 eV) due to the higher magnetic moment. A large magnetic moment for the Mn atom is predicted to be 3.81 μ_B. We suggest the ferromagnetic order of the Mn moments and the ferromagnetic coupling to the Ni substrate, which confirms the experimental results. The magnetism of Mn is identified as the driving force of the large buckling and the work-function change. The comparison with the other magnetic surface alloys is also presented and some trends are predicted.     

Radiation damage in single-crystal ice studied by 100 keV proton channeling

A detailed study has been undertaken of the Ni{100} (2 × 2)C structure formed by cracking ethylene on a clean Ni{100} surface. The LEED pattern shows characteristic missing spots which can be attributed to the presence of glide lines and indicate a space group symmetry of p4g. We show that this can be readily interpreted in terms of a distortion of the top nickel layer both parallel and perpendicular to the surface, which accompanies the carbon adsorption. Detailed comparisons of LEED intensity data with dynamical calculations indicate that the top layer nickel atoms are displaced 0.35 ± 0.05 Å parallel to the surface, 0.20 ± 0.05 Å outwards from the surface, and that the carbon atoms are in 4-fold hollows (now distorted) at a spacing of 0.1 ± 0.1 Å from the surface. These conclusions lead to a nickel-carbon nearest neighbour spacing of 1.803 ± 0.015 Å.     

ToF atom-probe fim investigation of surface segregation in dilute alloys

A time-of-flight atom-probe field ion microscope was successfully employed for the first time to investigate surface segregation in dilute alloys. We were able to achieve a single atomic layer resolution and obtained the absolute concentrations of alloy species of each surface layer. Cr atoms are found to segregate to the surface of Stainless Steel 410 whereas no segregation of the minority species was found for Pt-8% W and Pt-5% Ru. The first layer concentration of Cr in the {110} plane of Stainless Steel 410 at 500°C was found to be 38.5 ± 12.5% and 63.4 ± 10.2% respectively for samples with near surface layers Cr average concentration of 6.3 ± 2.1% and 11.9 ± 2.5%. The heat of segregation of Cr to the {110} plane of Stainless 410 was found to be 3.43 and 3.92 kcal/mole respectively from the two sets of data. The data also gives the difference in surface tensions between iron and chromium at this plane to be 269 and 282 erg/cm² respectively. Segregation studies on the {012} plane as well as on a grain boundary of Stainless Steel 410 were also done. In some cases, though the first surface layer is enriched with Cr in Stainless Steel 410, the near surface layers show a depletion of Cr. In Pt-8% W and Pt-5% Ru, our concentration depth profiles with a single atomic layer resolution show no segregation or depletion of the minority species either for the top layers or for the near surface layers.     

硫在镍(100)表面偏析动力学研究

本文使用AES-LEED联合装置研究了650—800℃温度范围内硫在镍(100)表面上的偏析动力学。结果表明,在较短退火时间内硫的表面浓度正比于退火时间的平方根,与McLean的动力学模型是一致的。扩散系数与温度的关系为D(cm²/s)=5×10^-3exp(-44600/RT)。硫偏析在镍(100)表面达到饱和值,LEED观察指出形成了硫的c(2×2)结构。深度剖面分析,硫/镍俄歇峰高比随氩离子剥离时间指数降低。 关键词：     

Trapping probabilities and desorption energies of alkali atoms on a clean and an oxygen covered tungsten (110) surface

Alkali atoms were scattered with hyperthermal energies from a clean and an oxygen covered (θ ≈ 0.5 ML) W(110) surface. The trapping probability of K and Na atoms on oxygen covered W(110) has been measured as a function of incoming energy (0–30 eV) and incident angle. A considerable enhancement of trapping on the oxygen covered surface compared to a clean surface was observed. At energies above 25 eV there are still K and Na atoms being trapped by the oxygen covered surface. From the temperature dependence of the mean residence time τ of the initially trapped atoms the pre-exponential factor τ₀ and the desorption energy Q were derived using the relation: $\text{τ = τ}{}_0\text{exp}\text{(}\text{Q}\text{kT}{}_{\mathrm{<mtext>s</mtext>}}\text{)}$. On clean W(110) we obtained for Li: $\text{τ}{}_0\text{= (8 ±}\text{8}\text{4}\text{) × 10}{}^{\mathrm{?14}}\text{sec}$, Q = (2.78 ± 0.09) eV; for Na: τ₀ = (9 ± 3) × 10^?14 sec, Q = (2.55 ± 0.04) eV; and for K: τ₀ = (4 ± 1) × 10^?13 sec, Q = (2.05 ± 0.02) eV. Oxygen covered W(110) gave for Na: τ₀ = (7 ±3) × 10^?15 sec, Q = (2.88 ± 0.05) eV; and for K: $\text{τ}{}_0\text{= (1.3 ±}\text{0.9}\text{0.6}\text{) × 10}{}^{\mathrm{?14}}\text{sec}$, Q = (2.48 ±0.05) eV. The adsorption on clean W(110) has the features of a supermobile two-dimentional gas; on the oxygen covered W(110) adsorbed atoms have the partition function of a one-dimen-sional gas. The binding of the adatoms to the surface has a highly ionic character in the systems of the present experiment. An estimate is given for the screening length of the non-perfect conductor W(110):k_s^?1≈ 0.5 Å.     

Positive spin polarization in field emission from Ni (110) and demagnetization by hydrogen adsorption

The spin polarization of field-emitted electrons from the (110)-surface of ferromagnetic Ni was observed to be P = (+ 5 ± 2)% (majority spin electrons predominant). This result can be understood qualitatively in the framework of the Stoner-Wohlfarth-Slater model, using hybridized s-d bands. Adsorption of hydrogen (saturation coverage) was found to reduce the spin polarization of electrons emitted along [110] to P (H₂) = (+ 1 ± 2)%, suggesting a demagnetization of the (110)-surface of Ni by hydrogen chemisorption.     

Surface structures of W(110) and W(100) faces by the dynamical LEED approach

By means of an efficient dynamical LEED method, the surface structures of W(110) and W(100) faces are examined. It is found that the W(110) surface maintains the bulk structure, despite the possibility for the top tungsten atoms to settle into sites of higher coordination number. The W(100) face exhibits a possible contraction of the top atomic layer by 0.10 ± 0.10 Å. These results fit into a trend correlating a top-layer contraction with the absence of close-packing in the top layer, i.e. with the roughness of the surface.     

A vibrational study of ammonia chemisorbed on Ni(110) and Ni(111): whither goest the metal-nitrogen stretching mode on FCC (111) surfaces?

The adsorption of ammonia on the Ni(110) and Ni(111) surfaces has been studied with high resolution (≤ 65 cm_?1) electron energy loss spectroscopy (EELS) combined with thermal desorption spectroscopy. The EELS spectra of the initial chemisorbed layer or α state on each surface are very different. Ammonia chemisorbed on the Ni(110) surface exhibits a strong Ni-N stretching mode at 570 cm^?1 which is absent on the Ni(111) surface. The Ammonia adsorption site appears to be different on the Ni(110) and Ni(111) surfaces. We suggest that the absence of the M-N stretching mode on the Ni(111) surface is a general characteristic of the ammonia adsorption site on the (111) surfaces of fcc Group VIII metals.     

Small Ni-S bond lengths in a c(2 × 2) overlayer of sulfur on Ni (001)

We conclude from the close agreement between low-energy electron diffraction calculations and experiment that sulfur adsorbed in a c (2 × 2) structure on Ni (001) is located 1.30 ± 0.1 Å above the surface in a four- fold coordinated bonding site. This location corresponds to a Ni-S bond length which is smaller than occurs in several bulk compounds or than suggested in a previous calculation by Duke et al.     

Structure study of oxygen-adsorbed Ni(111) surface by high energy ion scattering

Surface atomic structures of clean, oxygen-adsorbed, and oxidized (111) nickel have been studied quantitatively by using MeV ion scattering in combination with AES and MEED. We show that; the clean (111) nickel surface has the bulk-like structure with reconstruction or relaxation less than 0.02 Å, the surface thermal vibration amplitude is enhanced by ~20% compared to the bulk value, adsorbed oxygen results in surface lattice expansion by ~0.15 Å which is closely correlated to the p(2 × 2) or (√3 × √3) R30° superstructure, and oxidation at room temperature saturates at a stage which incorporates ~ 3 monolayers of nickel in a stoichiometric amorphous film of NiO whereas at temperatures higher than ~200° C thicker oxide films are produced. Our study indicates that each oxygen atom adsorbed on the Ni(111) surface interacts with and relaxes three nearest neighbor nickel atoms, and after saturation of the relaxation, oxidation of three monolayers takes place abruptly after which the oxide layer on the surface apparently blocks further reaction.     

NiTi合金的第一性原理研究

采用第一原理平面波方法,计算了NiTi合金B2相的体相性质,如晶格常数,形成能和结合能,弹性常数,计算的结果和实验数据以及别人的计算结果符合得很好.其次,计算了NiTi(100),(110)表面的几何结构和电子结构,计算结果表明,(100)表面具有表面振荡现象,(110)表面产生了表面波纹,最外层的Ti原子相对理想表面向真空层移动了0.198?,Ni原子向表面内移动了0.122?.比较表面的电子结构,NiTi(100)表面Ti端位较Ni端位更容易发生反应,而(110)表面较体相更稳定. 关键词： NiTi 第一性原理 电子结构 表面     

The vibrational modes of hydrogen adsorbed on Ni(110)

By studying the vibrational modes of H on Ni(110) as a function of coverage and temperature, a local picture of H site occupation is obtained in the lattice gas regime and on the (1 × 2) reconstructed surface at low temperature and for the irreversibly disordered surface formed by thermal conversion. Threefold sites are deduced from our data in both the lattice gas and the (1 × 2) reconstructed low temperature phases, with an additional loss in the latter phase ascribed to a second layer site. After thermal conversion, the threefold sites are depleted with a ? 0.5 monolayer (ML) transfer of H to second layer sites which appear to stabilize the surface and with ~ 0.5 ML H desorbing. Readsorption on the disordered surface indicates that a small amount of empty threefold Ni sites are still present after conversion. Various other models and site assignments are also discussed for comparison to the results of this study.     

Al表面的"类液"结构及其自扩散通道

应用分子动力学方法,采用嵌入势模型在熔点下和熔点上对Al(001),(110)和(111)表面的原子结构和自扩散现象进行研究.发现这些表面的第一层原子在低于熔点时,Al(110)面在700±10 K,Al(001)面在 860±10 K,Al(111)面在 930±10 K呈现明显自扩散且最终转变为"类液"结构,而其余各层仍保留有序状态.对这种"类液"结构进行均方位移、结构有序参数、径向分布函数和z向粒子密度分析,发现其结构和扩散行为与熔化的Al表面不同,并能在一定温度区间稳定存在.在"类液 关键词： 表面结构 分子动力学 自扩散