Proton conductive amorphous thin films of tungsten oxide clusters with acidic ligands

Three kinds of peroxo-polytungstic acid (PPTA, C-PPTA and N-PPTA) were obtained by reacting hydrogen peroxide with metallic tungsten, tungsten carbide or tungsten nitride, respectively. Polytungstates, C-PPTA and N-PPTA, were found to contain oxalate and nitrate ligands. Their proton conductivities were compared using thin film specimens spin-coated from their water solution. Conductivity of each as-coated film was in the range from 10⁻³ to 10⁻⁴ S cm⁻¹ under the relative humidity of 40% (25 °C). A sharp decrease in conductivity (to less than 10⁻⁷ S cm⁻¹ at 25 °C) was observed for PPTA without acidic ligands after thermal treatment at 80 °C. However, the effect of thermal treatment on C-PPTA or N-PPTA was much milder. A 80 °C-treated C-PPTA film showed the conductivity of 1.0 × 10⁻⁵ S cm⁻¹ (25 °C) with a very weak dependency on ambient humidity.     

Conductivity anisotropy in directionally solidified CaZrO3---CaSZ and MgO-MgSZ eutectics

The results of the impedance spectroscopy measurements on eutectic samples based on zirconium oxide are presented here. Samples of CaZrO₃---ZrO₂(cubic) and MgO---ZrO₂(cubic) have been grown by a directional solidification procedure such that the different phases appear nearly oriented along the growth direction (lamellae in the system of CaZrO₃-ZrO₂(cubic) and fibers of MgO in a ZrO₂ matrix in the other system). The DC electrical conductivity has been measured by impedance spectroscopy along and across the growth axis. For CaZrO₃---ZrO₂ the coductivity is clearly anisotropic. The following values for σT have been obtained: the conductivity at 600 °C equals 2.0 × 10⁻⁶ Ω⁻¹ cm⁻¹ perpendicular to the fiber axis and 1.4 × 10⁻⁵ Ω⁻¹ cm⁻¹ parallel to it and with an activation energy of 1.3 eV for σT. For MgO---ZrO₂(cubic) the isotropic value of the conductivity at 600 °C is 10⁻⁴ Ω⁻¹ cm⁻¹ with activation energy for σT of 1.5 eV. The anisotropic conductivity in the CaZrO₃---ZrO₂ (cubic) system has been explained by a model of an ordered stacking of oxygen conducting (cubic ZrO₂) and non-conducting (CaZrO₃ or MgO) phases.     

Effect of branching in base polymer on ionic conductivity in hyperbranched polymer electrolytes

Novel hyperbranched polymer, poly[bis(diethylene glycol)benzoate] capped with a 3,5-bis[(3′,6′,9′-trioxodecyl)oxy]benzoyl group (poly-Bz1a), was prepared, and its polymer electrolyte with LiN(CF₃SO₂)₂, poly-Bz1a/LiN(CF₃SO₂)₂ electrolyte, was all evaluated in thermal properties, ionic conductivity, and electrochemical stability window. The poly-Bz1a/LiN(CF₃SO₂)₂ electrolyte exhibited higher ionic conductivity compared with a polymer electrolyte based on poly[bis(diethylene glycol)benzoate] capped with an acetyl group (poly-Ac1a), and the ionic conductivity of poly-Bz1a/LiN(CF₃SO₂)₂ electrolyte was to be 7×10⁻⁴ S cm⁻¹ at 80 °C and 1×10⁻⁶ S cm⁻¹ at 30 °C, respectively. The existence of a 3,5-bis[(3′,6′,9′-trioxodecyl)oxy]benzoyl group as a branching unit present at ends in the base polymer improved significantly ionic conductivity of the hyperbranched polymer electrolytes. The polymer electrolyte exhibited the electrochemical stability window of 4.2 V at 70 °C and was stable until 300 °C.     

Poly(ethylene oxide-co-epichlorohydrin)/NaI: a promising polymer electrolyte for photoelectrochemical cells

We have investigated the thermal and ionic conductivity properties of the elastomer poly(ethylene oxide-co-epichlorohydrin) filled with NaI and I₂. The reason for using this composition is its potential application as electrolyte in photoelectrochemical cells. This copolymer was characterized as a function of NaI concentration, temperature and relative humidity. According to the data obtained, the Na⁺ ion interacts with the ethylene oxide repeating units by means of Lewis type acid–base interactions. The empirical Vogel–Tamman–Fulcher equation was used to model the conductivity and temperature relationships, indicating that the conduction occurs in the amorphous phase of the copolymer. The sample with 9.0% (w/w) of NaI presents a conductivity of 1.5×10⁻⁵ S cm⁻¹ in a dry atmosphere (30°C, [H₂O]<1 ppm) and 2.0×10⁻⁴ S cm⁻¹ at 86% relative humidity (22°C).     

Sr-doped LaInO3 and its possible application in a single layer SOFC

The effects of dopants on the electrical conductivity of the perovskite-type oxide LaInO₃ have been investigated. Replacement of La by Sr is the most effective way to enhance the conductivity of LaInO₃, whereas Ca substitution for In is rather difficult due to the large difference in the ion radii. The optimum composition is La_0.9Sr_0.1InO_3−δ whose maximum conductivity is 7.6×10⁻³ S cm⁻¹ at 900°C. The electrical conductivity of La_0.9Sr_0.1InO_3−δ has been measured over a wide range of oxygen partial pressure from pO₂=1 to 10⁻²⁵ atm. P-type and n-type behavior at high and low oxygen partial pressure have been observed, respectively, while at intermediate oxygen partial pressures, the electrical conductivity changes only slightly with the oxygen partial pressure. The concept of a single layer solid oxide fuel cell based on a La_0.9Sr_0.1InO_3−δ ceramic pellet has been tested. A maximum power density of 3 mW cm⁻² at 800°C was achieved when dilute H₂ and air were used as fuel and oxidizing agent, respectively.     

Ionic conductivity of crystalline and glassy Mg4.5Na7(P2O7)4

In our work single crystals of Mg_4.5Na₇(P₂O₇)₄ were prepared, pulverized, pressed into pellets and sintered in order to measure the electrical conductivity of polycrystalline specimens. The conductivity was also measured on glassy specimens obtained by the melting of previously prepared crystals. The electrical conductivities at 25°C with values of the order of 10⁻¹⁶ Ω⁻¹ cm⁻¹ for polycrystalline samples and a value of the order of 10⁻¹⁴ Ω⁻¹ cm⁻¹ for glass, show that the glassy phase of Mg_4.5Na₇(P₂ because of its greater molar volume and loosely packed structure, is a better matrix for ionic motion.     

Polymer electrolytes based on ethylene oxide–epichlorohydrin copolymers

In this work we studied the ionic conductivity for three copolymers of the title co-monomers as a function of LiClO₄ content, temperature and ambient relative humidity. We also investigated the interactions between the salt and the co-monomer blocks in the copolymers and its effect on the morphology and thermal properties of the copolymer/salt complexes. Our data indicate that the Li⁺ ion predominantly interacts with the ethylene oxide repeating units of the copolymers. The copolymer with the highest ionic conductivity was obtained with an ethylene oxide/epichlorohydrin ratio of 84/16 containing 5.5% (w/w) of LiClO₄. It showed a conductivity of 4.1×10⁻⁵ S cm⁻¹ (30°C, humidity< 1 ppm) and 2.6×10⁻⁴ S cm⁻¹ at 84% relative humidity (24°C). The potential stability window of the copolymer/salt complex is 4.0 V, as measured by cyclic voltammetry. For comparison, we also prepared a blend of the corresponding homopolymers containing LiClO₄; it showed higher crystallinity and lower ionic conductivity.     

Structural and electrical properties of crystalline (1−x)Ta2O5−xTiO2 thin films fabricated by metalorganic decomposition

Polycrystalline (1−x)Ta₂O₅−xTiO₂ thin films were formed on Si by metalorganic decomposition (MOD) and annealed at various temperatures. As-deposited films were in the amorphous state and were completely transformed to crystalline after annealing above 600 °C. During crystallization, a thin interfacial SiO₂ layer was formed at the (1−x)Ta₂O₅−xTiO₂/Si interface. Thin films with 0.92Ta₂O₅–0.08TiO₂ composition exhibited superior insulating properties. The measured dielectric constant and dissipation factor at 1 MHz were 9 and 0.015, respectively, for films annealed at 900 °C. The interface trap density was 2.5×10¹¹ cm⁻² eV⁻¹, and flatband voltage was −0.38 V. A charge storage density of 22.8 fC/μm² was obtained at an applied electric field of 3 MV/cm. The leakage current density was lower than 4×10⁻⁹ A/cm² up to an applied electric field of 6 MV/cm.     

Defect versus nanocrystal luminescence emitted from room temperature and hot-implanted SiO2 layers

Silicon nanocrystals have been synthesized in SiO₂ matrix using Si ion implantation. Si ions were implanted into 300-nm-thick SiO₂ films grown on crystalline Si at energies of 30–55 keV, and with doses of 5×10¹⁵, 3×10¹⁶, and 1×10¹⁷ cm⁻². Implanted samples were subsequently annealed in an N₂ ambient at 500–1100°C during various periods. Photoluminescence spectra for the sample implanted with 1×10¹⁷ cm⁻² at 55 keV show that red luminescence (750 nm) related to Si-nanocrystals clearly increases with annealing temperature and time in intensity, and that weak orange luminescence (600 nm) is observed after annealing at low temperatures of 500°C and 800°C. The luminescence around 600 nm becomes very intense when a thin SiO₂ sample is implanted at a substrate temperature of 400°C with an energy of 30 keV and a low dose of 5×10¹⁵ cm⁻². It vanishes after annealing at 800°C for 30 min. We conclude that this luminescence observed around 600 nm is caused by some radiative defects formed in Si-implanted SiO₂.     

Preparation and characterization of a lithium ion conducting electrolyte based on poly(trimethylene carbonate)

In this paper, the results of preliminary studies of two new solvent-free polymer electrolytes based on poly(trimethylene carbonate), p(TMC), with lithium trifluoromethanesulphonate, (triflate), and lithium perchlorate are described. Thin films of these electrolytes were obtained by evaporation of solvent from homogeneous mixtures of known masses of host polymer and salt. Electrolytes with compositions of n between 1.5 and 85, where n represents the molar ratio of (O=COCH₂CH₂CH₂O) units per lithium ion, have been prepared. These solvent-free electrolytes were characterized by measurements of total ionic conductivity, differential scanning calorimetry (DSC) and thermogravimetry (TGA). As expected from previous studies with these salts in poly(ethylene oxide), PEO, the triflate-based system showed superior thermal stability but with a lower total ionic conductivity than that of the perchlorate-containing electrolyte. The highest conductivity (approximately 3×10⁻⁴ Ω⁻¹ cm⁻¹) was found at 95°C with the electrolyte composition of (TMC)₂LiClO₄.     

Study of fossil tracks due to VH and VVH groups of cosmic ray nuclei in olivine crystals from Luna-16 and Luna-24

The olivine crystals from lunar regolith samples taken by the Soviet unmanned spacecrafts Luna-16 and Luna-24 were investigated. Eleven 0.5 –1.0 mm size olivine crystals were mounted in epoxy, polished and then etched in modified WO₄ solution. The Fe-group track densities up to 10⁸ tracks.cm⁻² (Fe-group) were measured under optical microscope. The tracks of length greater than 30 microns due to Z ≥ 36 cosmic ray nuclei are counted for VVH tracks density for all the crystals. The VVH / VH track densities ratio for these lunar olivine crystals varies from 1.25×10⁻⁴ to 2×10⁻³. It corresponds to the averaged depth of these crystals in lunar soil of 2–8 cm during galactic cosmic ray exposure. Lunar crystals are well suited for VVH track studies due to a very high track density. Two crystals were annealed at 430°C for 32 hrs. This procedure eliminates iron group tracks completely and leaves etchable tracks of nuclei with Z 50 even in the olivine crystals with Fe-group tracks up to 1–2×10⁸ tracks cm⁻². We were able to measure two tracks with the length 195 and 210μm which were produced by Th---U group of Galactic cosmic ray nuclei.     

MnO thin film cathode for rechargeable microbatteries

Thin films of MnO were deposited by electron beam evaporation using a MnO or MnO₂ source. The thin films were charaterized by X-ray and electron diffraction. The Coulomb titration curve reveals a potential plateau of 2.9 V over the composition range 0.05<x<2.0. The chemical diffusion coefficient of lithium in thin films at 15°C is 2.7×10⁻¹⁴ cm²/s for 0<x<0.01 and 2.2×10⁻¹⁵ cm²/s for 0.02<x<0.06. Good reversibility for lithium insertion and extraction is demonstrated by cyclic voltammetry.     

Nombres D''ondes Absolus De La Bande ν3 De OCS Par Spectroscopie De Fourier

Absolute wavenumbers of 140 lines belonging to ν₃ band of ¹⁶O¹²C³²S, around 2060 cm⁻¹, are measured under vacuum with a high resolution Fourier Spectrometer, within ±0.11 × 10⁻³ cm⁻¹ (3.1 MHz) . They achieve a 20-fold improvement in accuracy over previous measurements and are consequently proposed as secondary infrared standards. Molecular constants are reported.     

Annealing effects on zirconium nitride films

ZrN films were deposited by dc reactive magnetron sputtering on silicon substrates under optimized nitrogen partial pressure of 6×10⁻⁵ mbar. Structural, electrical and optical properties were systematically investigated. Films deposited at room temperature exhibited Schottky structure without any silicide interfacial layer. These films have electrical resistivity of 4.23×10⁻³ Ω cm, which were crystalline in nature, with cubic (1 1 1) orientation. Refractive index and extinction coefficient were found to be 1.95 and 0.43, respectively at a wavelength of 350 nm.

Samples were annealed for 1 h in air at two temperatures, 350 and 550 °C. Scanning electron microscopy (SEM) and energy dispersive analysis of X-rays (EDAX) showed alloy penetration pits. Extent of penetration was greater in the films, which were annealed at higher temperature (550 °C). Variation in refractive index was observed in the range of 1.95–1.80 at 350 nm, for the annealed films, with increase in grain size from 7.25 to 11.10 nm. Poly-crystalline nature has been observed with (1 1 1) and (2 0 1) orientations. Resistivity is found to increase from 4.23×10⁻³ to 6.21×10⁻³ Ω cm.     

Material design of new lithium ionic conductor, thio-LISICON, in the Li2S–P2S5 system

A new lithium ionic conductor of the thio-LISICON (LIthium SuperIonic CONductor) family was found in the binary Li₂S–P₂S₅ system; the new solid solution with the composition range 0.0≤x≤0.27 in Li_3+5xP_1−xS₄ was synthesized at 700 °C and characterized by X-ray diffraction measurements. Its electrical and electrochemical properties were studied by ac impedance and cyclic voltammetry measurements, respectively. The solid solution member at x=0.065 in Li_3+5xP_1−xS₄ showed the highest conductivity value of 1.5×10⁻⁴ S cm⁻¹ at 27 °C with negligible electronic conductivity and the activation energy of 22 kJ mol⁻¹ which is characteristic of high ionic conduction state. The extra lithium ions in Li₃PS₄ created by partial substitution of P⁵⁺ for Li⁺ led to the large increase in ionic conductivity. In the solid solution range examined, the minimum conductivity was obtained for the compositions, Li₃PS₄ (x=0.0 in Li_3+5xP_1−xS₄) and Li₄P_0.8S₄ (x=0.2 in Li_3+5xP_1−xS₄); this conductivity behavior is similar to other thio-LISICON family with the general formula, Li_xM_1−yM_y′S₄ (M=Si, Ge, and M′=P, Al, Zn, Ga, Sb). Conduction mechanism and the material design concepts are discussed based on the conduction behavior and the structure considerations.     

Observation of two-photon emission in nuclear pion capture

The emission of two photons above 25 MeV energy was observed in the capture of stopped pions by beryllium and carbon with a rate of (1.0 ± 0.1) × 10⁻⁵, respectively (1.4 ± 0.2) × 10⁻⁵ per capture. These rates are about two to four times greater than various free-nucleon estimates based on the π⁻+π⁺→γγ annihilation mechanism alone.     

Preparation of tantalum oxide thin films by photo-assisted atomic layer deposition

Tantalum oxide thin films were prepared by photo-assisted atomic layer deposition (Photo-ALD) in the substrate temperature range of 170–400 °C using Ta(OC₂H₅)₅ and H₂O as precursors. The constant growth rates of 0.42 and 0.47 Å per cycle were achieved for the films grown by normal ALD and Photo-ALD, respectively. The increased growth rate in Photo-ALD is probably due to the reactive surface by photon energy and faster surface reaction. In Photo-ALD, however, the constant growth rate started at lower temperature of 30 °C and one cycle time shortened up to 5.7 s than that of normal ALD. The films grown by normal ALD and Photo-ALD were amorphous and very smooth (0.21–0.35 nm) as examined by X-ray diffractometer and atomic force microscopy, respectively. Also, the refractive index was found to be 2.12–2.16 at the substrate temperature of 190–300 °C, similar to that of the film grown by normal ALD. However, the remarkably low leakage current density of 0.6×10⁻⁶ A/cm² to 1×10⁻⁶ A/cm² at applied field of 1 MV/cm is several order of magnitude smaller than that of normal ALD, probably due to the presence of reactive atom species.     

Davydov splitting and two-photon excitation of cadmium tungstate (CdWO4) single crystal phosphorescence

Phosphorescence characteristics of CdWO₄ excited by one-photon (λ = 308 nm) and two-photon (λ = 570–590 nm) processes were measured. A Davydov splitting of 120 ± 20 cm⁻¹ was obtained in the phosphorescence spectra, suggesting a diffusion coefficient of about 1.2 × 10⁻² cm² s⁻¹, and a diffusion length of about 3.1 × 10⁻⁴ cm for the room temperature measured lifetime of 8μs. The phosphorescence quantum efficiency was less than 2% at low temperatures (only 0.25% at room temperature), indicating that the dominant decay mechanism was radiationless. The radiative lifetime was thus estimated as 1–2 ms. The two-photon phosphorescence excitation is characterized by an absorption cross-section of the order of 10⁻⁴⁹cm⁴s.     

Preliminary results on Cu diffusion through grain boundaries of thin ion-plated Ag---Sn films

The diffusion process of copper through grain boundaries of 500 nm thick ion-plated Ag-12at%Sn films was studied in the temperature range 100–250°C. The method is based on the determination of the time of first appearance of Cu on the Ag---Sn surface using Auger electron spectroscopy for determining trace amounts of Cu. An activation energy of E_a = 0.53 eV and a diffusivity of D′_o = 1.3 × 10⁻⁷cm²s⁻¹ was obtained. For comparison, diffusion studies of Cu through ion-plated pure Ag layers have been performed. In this case an activation energy of E_a = 0.68 eV and a diffusivity of D′_o = 2.3 × 10⁻⁵cm²s⁻¹ have been found.     

A new measurement of the weak magnetism term in the betaspectra of B and N

The betaspectra of ¹²B and ¹²N have been measured with a NaI crystal as spectrometer. Assuming a shape correction factor 1 + aW + bW² and b₋ = 1.106 × 10⁻⁴ MeV⁻², b₊ = −1.397 × 10⁻⁴ MeV⁻², the spectra yield a₋ = (+0.91 ± 0.11) × 10⁻² MeV⁻¹ and a₊ = (−0.07 ± 0.09) × 10⁻² MeV⁻. the a₋ − a₊ = (+0.98 ± 0.09) × 10⁻² MeV⁻¹ is in agreement with the weak magnetism prediction.