三维面形测量数据的计算全息可视化

提出利用计算机制全息进行三维面形测量数据立体重现的技术。首先利用三维面形测量技术同时获取三维物体的强度和距离像；然后根据三维面形测量数据，设计和制作菲涅耳计算全息图；最后将计算全息和光学全息相结合，以菲涅耳计算全息图的光学再现像为对象，记录光学像全息。这样既解决了计算机制全息术中真实三维物体立体信息数据捕捉的问题，又为三维面形检测提供了一个行之有效的立体重构技术。给出了这种方法的原理、计算全息的设计、制作方案和实验验证结果。     

面向真彩色三维显示的分层角谱算法和Gerchberg-Saxton算法研究

分层角谱算法可用于三维物体全息图的生成计算,在计算时间、占用内存和算法复杂度方面占有优势.本文基于强度图和深度图的分层角谱算法,对多波长采样进行分析,有效抑制混频现象,实现了真彩色物体的计算全息图生成.针对分层角谱算法重建时产生的散斑噪声问题,引入Gerchberg-Saxton(GS)算法,提出基于分层角谱算法的GS算法.通过计算比较引入GS算法前后再现像的均方根误差和峰值信噪比,证明该算法可有效地抑制散斑噪声,提高全息图的再现像质量,更适用于复杂形貌三维物体的计算.     

基于经验小波变换及核概率密度的物体表面变形测量

采用CCD相机采集物体变形前后的散斑图片,利用一维经验小波变换对散斑图片进行逐行分解,获得一系列的固有分量.根据分解后分量的核概率密度函数提出基于核概率密度的自适应降噪法,去除噪声干扰,提取跟变形信息相关的分量并重构,利用重构后的每一行获得变形前后重构散斑图.采用Hilbert法计算重构后散斑图的相位,对变形前后散斑图相位进行相减,根据相位差进行解包裹获得物体表面变形信息.实验结果表明该方法能够有效地对物体表面变形进行测量,且测量精度较经验模态分解提高4倍.     

三维电子散斑干涉载频调制及其在柴油机上的应用

将电子散斑干涉场的三维载波调制技术应用到三维物体变形测量中.用水平方向、竖直方向及垂直试件表面的三路相干光分别照明物体，在水平和竖直方向通过控制反射镜的微小偏转引入载波，实现位移场干涉条纹的调制；利用物体的微小偏转实现离面位移场干涉条纹的调制；结合傅里叶变换法，分别解调出变形场的位相，从而实现了物体三维变形场的精确测量.将该技术应用到柴油机油泵的三维位移测量上，成功测量了油泵的三维位移场.     

LED光源数字全息技术研究

研究以发光二极管(LED)作为光源的部分相干光数字全息技术.首先研究LED的时间相干性和空间相干性,尽管LED的时间相干性较差,但空间相干性可以通过减小光源发光面积来提高.利用LED的时间相干性较差、相干长度短的特点,抑制相干噪声,改善数字全息重建质量.在同一全息记录系统,通过实验,比较了用激光和LED光源的数字全息重建图像质量.结果表明:基于LED光源的数字全息,完全消除了使用激光光源的散斑噪声和由光学元件引入的寄生干涉噪声,物光场的重现质量,包括振幅和相位都得到了很大提高.但由于LED光源的较低的空间相干性,一般只适用于同轴相移数字全息,待测物体的厚度在十几微米以内,应用受到一定限制.     

三维漫射体单波长真彩色彩虹全息术

提出一种新的三维漫反射物体真彩色彩虹全息术,在普通一步法真彩色彩虹全息术的基础上,用单波长激光逆光路再现,可在同一种记录介质上一次曝光记录三维物体的真彩色全息图.因而特别适合于制作光致抗蚀剂模压全息母板.     

基于自聚焦透镜的光纤数字全息系统实验研究

在光纤数字全息光路中引入自聚焦透镜，利用其特有的成像特性，作为物光波的中继传输器件，构成一套紧凑型光纤数字无透镜傅里叶变换全息记录系统，以实现对微小物体的全息记录与数值再现.研究结果表明，结合自聚焦透镜和光纤数字全息术的特点，不仅可使光学测试系统紧〖CM(42〗〖JP2〗凑、微型化，而且还可以对一些特殊环境、光线难以直接到达的隐藏区域或封闭系统内部进行测量.     

多光束数字全息的研究

提出了一种多光束数字全息技术来解决当利用菲涅耳数字全息对全息图进行再现时,物体的多个表面无法同时再现得明亮、清晰.该方法是记录时采用多光束照明同一物体的多个表面,增强CCD上接收到的物体侧表面散射光的强度.实验成功地同时再现了物体的多个表面.同时,为了减弱再现像的散斑噪声,采用双线性插值和中值滤波处理图像,获得了质量高的三维物体的再现图像.     

利用激光全息干涉测量梁的微小位移

全息干涉测量利用二次曝光记录物体在不同载荷状态下的相对位移场.通过在干板上记录和比较不同状态产生的光波的干涉,可以得到在不同载荷时干涉条纹随物体位移的变化情况,实现对物体微小变形、微小位移量的测量.本文利用激光全息干涉技术测量了金属梁的微小位移量,计算得到金属梁的弹性模量和挠度.     

对物体沿散斑片纵向移动二次曝光全息干涉条纹的诠释

从光学几何关系出发,推导了在平行光照明、物体沿散斑片纵向方向微小移动情况下的一种全息干涉条纹的解释方法.该方法可以根据任一瞬间的条纹间距测量物体的位移,并适用于实时全息监测的定量分析,对全息干涉计量术提供有效的条纹解释方法和物体位移的计算方法.     

Lensless digital holography with short-coherence light source for three-dimensional surface contouring of reflecting micro-object

In this paper, a new lensless digital holography system with short-coherence light source is reported for recording three-dimensional surface contouring of reflecting micro-objects. In the experiment, each of the layers on the inwall of a conical pore is respectively recorded by changing the path length of the object beam, instead of changing that of the reference beam, which can reduce the recording complexity and errors. In addition, the least-square-polynomial-fitting is used for the first time to carry out three-dimensional reconstruction with a series of two dimensional intensity images of a micro-object, which can be used not only to reduce obviously the complication of the three-dimensional reconstruction, but also to carry out three-dimensional reconstruction of a micro-object with strong laser speckle noise, of which the phase images can not be obtained from the conventional phase unwrapping process.     

球面参考光预放大数字全息成像系统分辨力

为了提高数字全息成像系统的成像分辨力,对以球面波作为参考光波的预放大数字全息成像系统的记录和再现过程进行了理论推导,得出了该系统的脉冲响应表达式,并由此分析了决定该系统成像分辨力的因素。在CCD成像分辨力高于显微物镜分辨力的情况下,通过对分辨力测试板进行实验,讨论了系统分辨力与记录距离的关系。结果表明:再现像的分辨力对记录距离不敏感;但在记录距离为零,即像面数字全息系统下,再现像具有更高的分辨力。实验结果与理论分析一致。     

微细铣刀位姿同轴全息重建方法

微细铣刀在主轴上存在装夹偏角时,会加剧刀刃磨损,降低刀具使用寿命.为了精确观测微细铣刀在机倾斜状态,提出了基于景深的微细铣刀三维位姿重建方法.利用激光同轴数字全息实验装置得到微细铣刀全息图,并通过菲涅尔再现算法获得再现像.在再现像中提取刀具边缘点作为关键点,采用小波变换局部方差算子求出关键点的聚焦程度,确定铣刀对应的轴...     

Spatial-frequency version theory of three-dimensional holograms

A spatial-frequency version of high efficiency three-dimensional holograms of complex wave fields has been achieved. It has been shown that a three-dimensional hologram recorded by a plane reference wave may be described by means of a complex transfer function, which is found here analytically. Analysis of amplitudephase wave field distortions, under different recording and reconstruction conditions, has been carried out.     

数字全息图取样模型的简化研究

数字全息研究领域目前存在两种不同的数字全息图取样模型.按照这两种模型进行研究时, 不但涉及较复杂的数学运算, 在许多情况下还会导致不同的研究结果, 不便于理论分析及实际应用.基于对数字全息图记录的物理过程分析及电荷藕合器件(charge coupled device, CCD)几何结构的研究, 本文将这两种取样模型简化为相同的数学表达式. 利用数字全息图的余弦级数展开及取样定理对简化模型的研究表明, 简化模型不但具有清晰的物理意义, 而且可以方便地为应用研究服务. 基于简化模型对物光波通过光学系统到达CCD的数字全息记录系统进行了研究, 导出得到实验证实的波前重建表达式. 关键词： 数字全息 波前重建 相干光成像     

近距离数字全息术记录和再现问题

讨论了记录距离小于菲涅耳衍射要求的近距离数字全息记录和再现问题。对全息记录与再现中高次相位的补偿问题进行了分析,证明了在CCD的参量和记录距离给定后,只要记录时使物体的大小、球面参考光波的位置和距离满足一定的条件,即使在记录距离小于菲涅耳衍射要求的最小距离情况下,也可将高次相位的影响补偿到足够小,使得近距离数字全息的数字再现仍可用快速傅里叶变换算法计算。推导出了满足高次相位补偿的条件和满足补偿条件时的数值再现计算公式。实验结果与理论分析的结论相吻合,并给出了一种修正实际记录的参考光和计算机模拟的理想参考光之间偏差的方法。     

Use of digital color holography for crack investigation in electronic components

This paper presents the experimental optical analysis of the crack inside an electronic component. The optical setup is used to carry out multidimensional deformation measurements using digital color holography and the spatial multiplexing of holograms. Since the Fresnel transform method depends on wavelength, a wavelength-dependent-zero-padding algorithm is described and results in a rigorous sizing of each reconstructed monochrome image. The criterion to optimize the parameters is presented and is based on minimizing the widening of the impulse response of the full recording/reconstruction process. The application of the proposed method is illustrated through the analysis of the mechanical deformation of the electronic component, and offers keys to understand its failure mode in industrial conditions.     

Full-view rainbow-reflection holograms

A simple method of recording full-view rainbow-reflection holograms on a single flat plate is described: only one white-light illuminating source is required in the reconstruction process. The hologram can be viewed from opposite sides, where each side of a three-dimensional object, with its original spatial relationship, is displayed in bright colours.     

Three-dimensional holographic reconstruction of two-dimensional image information from serial sections and its applications in biomedicine

An experimental study to synthesize holographically two-dimensional projections of serial sections at various depths into three-dimensional images is described. The effects caused by the position, size and resolution of virtual images during reconstruction are analysed, and the advantages and limitations of this method are discussed. An application of this experimental method — the three-dimensional reconstruction of serial sections of a newt embryo — is presented.     

Sectional image reconstruction and three-dimensional microscopy of small particles by angular spectrum method

In this letter, we demonstrate sectional image reconstruction and three-dimensional microscopy of small particles. We demonstrate sectional image reconstruction and holographic methods to obtain 2D and 3D images of small particles. A single hologram is sufficient to obtain a section containing only the focused parts of the reconstructed image. One can obtain images of different plane sections of a specimen in addition to its 3D display. The reconstruction of a digital hologram is based on the plane-wave expansion of the diffracted wave fields using Fourier optics (this method is also known as the angular spectrum method). With this method, the object-to-hologram distance can be quite small because the minimum-distance requirement does not apply. Furthermore, numerical reconstruction of transparent objects by this method may be interesting for micro-structure measurement.