Application of ionic liquid doped solid polymer electrolyte

The electrical, structural, and photoelectrochemical properties of the polymer electrolyte PEO:NaI/I₂ doped with an ionic liquid 1-ethyl 3-methylimidazolium dicyanamide (EMImDCN) have been reported. Incorporation of the ionic liquid (IL) increases the membrane homogeneity, decreased surface roughness, and enhances the short current (J _sc). Additionally, the doping of IL provides more charge carriers which enhances overall ionic conductivity (σ). The optimized σ was found at 40 wt.% IL composition. The fabricated DSSC using this new solid electrolyte showed 1.43% efficiency at 100 mW cm⁻².     

Effects of compositions on properties of PEO–KI–I2 salts polymer electrolytes for DSSC

The effects of compositions on properties of PEO/KI/I₂ salts polymer electrolytes were investigated to optimize the photovoltaic performance of solid state DSSCs. XRD pattern for the mole ratio 12:1 of [EO:KI] was showed the formation of complete amorphous complex. DSC results also confirmed the amorphous nature of the polymer electrolyte. The highest value of ionic conductivity is 8.36 × 10^− 5 S/cm at 303 K (ambient temperature) and 2.32 × 10^− 4 S/cm at 333 K (moderate temperature) for the mole ratio 12:1 of EO:KI complex. The effect of contribution of [I⁻] and [I₃⁻] concentration with conductivity were also evaluated. FTIR spectrum reveals that the alkali metal cations were co-ordinated to ether oxygen of PEO. The formation of polyiodide ions, such as symmetric I₃⁻ (114 cm^− 1) and I₅⁻ (145 cm^− 1) caused by the addition of iodine was confirmed by FT Raman spectroscopic measurements. The optimum composition of PEO–KI–I₂ polymer electrolyte system for higher conductivity at ambient and moderate temperatures was reported. A linear Arrhenius type behaviour was observed for all the PEO–KI polymer complexes. Transport number measurements were carried out for several polymer electrolyte compositions. Dye-sensitized solar cells were fabricated by using higher conductivity polymer electrolyte compositions and its photoelectrochemical performance was investigated. The fill factor, short-circuit current, photovoltage and energy conversion efficiency of the DSSC assembled with optimized electrolyte composition were calculated to be 0.563, 6.124 mA/cm², 593 mV and 2.044% respectively.     

Solid polymer electrolytes based on squaric acid structure

Poly(squarate)s (PPS-1 and PPS-2) were synthesized by the reaction of squaryl dichloride with hydroquinone for PPS-1 and with 2,5-diethoxy-1,4-bis(trimethylsilyloxy)benzene for PPS-2, and the ionic conductivities, thermal properties, and electrochemical and thermal properties of their polymer electrolytes with LiN(CF₃SO₂)₂ were investigated. The ionic conductivity increased with increasing the lithium salt concentration for the PPS-1–LiN(CF₃SO₂)₂ electrolyte, and the highest ionic conductivities of 8.60 × 10⁻⁵ S/cm at 100 °C and 9.57 × 10⁻⁸ S/cm at 30 °C were found at the [Li] to [O] ratio of 2:1. And also, the ionic conductivity for the PPS-1–LiN(CF₃SO₂)₂ electrolyte increased with an increase in the lithium salt concentration, reached a maximum value at the [Li] to [O] ratio of 1:2, and then decreased. The highest ionic conductivity was to be 1.04 × 10⁻⁵ S/cm at 100 °C and 1.71 × 10⁻⁸ S/cm at 30 °C, respectively. Both polymer electrolytes exhibited relatively better electrochemical and thermal stabilities. Addition of the PPS-1 as a plasticizer into the poly(ethylene oxide) (PEO)–LiN(CF₃SO₂)₂ electrolyte system suppressed the crystallization of PEO, and improved the ionic conductivity at room temperature. Invited paper dedicated to Professor W. Weppner on his 65th birthday.     

Bacto agar-based gel polymer electrolyte

The biopolymer of a Bacto agar-based gel polymer electrolyte (GPE) was prepared by addition of NaI and I₂ as redox couple. The prepared GPE was characterized using impedance spectroscopy and X-ray diffraction (XRD) in order to determine its electrical and structural properties, respectively. An optimized ionic conductivity of 12.41 × 10⁻⁴ S cm⁻¹ was achieved for the samples containing 1.6 M NaI and 50 μL I₂. Meanwhile, XRD revealed that the addition of NaI and I₂ altered agar properties and formed an amorphous structure. Linear sweep voltammetry showed that the electrochemical stability window of the sample had a working voltage of 2.0 V.     

Structural,thermal and ion transport studies on nanocomposite polymer electrolyte-{(PEO + SiO<Subscript>2</Subscript>):NH<Subscript>4</Subscript>SCN} system

Development and characterisation of polyethylene oxide (PEO)-based nanocomposite polymer electrolytes comprising of (PEO-SiO₂): NH₄SCN is reported. For synthesis of the said electrolyte, polyethylene oxide has been taken as polymer host and NH₄SCN as an ionic charge supplier. Sol–gel-derived silica powder of nano dimension has been used as ceramic filler for development of nanocomposite electrolytes. The maximum conductivity of electrolyte ∼2.0 × 10⁻⁶ S/cm is observed for samples containing 30 wt.% silica. The temperature dependence of conductivity seems to follow an Arrhenius-type, thermally activated process over a limited temperature range.     

A novel PEO-based composite polymer electrolyte with NaAlOSiO molecular sieves powders

Ion-conducting thin film polymer electrolytes based on poly(ethylene oxide) (PEO) complexes with NaAlOSiO molecular sieves powders has been prepared by solution casting technique. X-ray diffraction, scanning electron microscopy, differential scanning calorimeter, and alternating current impedance techniques are employed to investigate the effect of NaAlOSiO molecular sieves on the crystallization mechanism of PEO in composite polymer electrolyte. The experimental results show that NaAlOSiO powders have great influence on the growth stage of PEO spherulites. PEO crystallization decrease and the amorphous region that the lithium-ion transport is expanded by adding appropriate NaAlOSiO, which leads to drastic enhancement in the ionic conductivity of the (PEO)₁₆LiClO₄ electrolyte. The ionic conductivity of (PEO)₁₆LiClO₄-12 wt.% NaAlOSiO achieves (2.370 ± 0.082) × 10⁻⁴ S · cm⁻¹ at room temperature (18 °C). Without NaAlOSiO, the ionic conductivity has only (8.382 ± 0.927) × 10⁻⁶ S · cm⁻¹, enhancing 2 orders of magnitude. Compared with inorganic oxide as filler, the addition of NaAlOSiO molecular sieves powders can disperse homogeneously in the electrolyte matrix without forming any crystal phase and the growth stage of PEO spherulites can be hindered more effectively.     

Structural and electrical properties of pure and H<Subscript>2</Subscript>SO<Subscript>4</Subscript> doped (PVA)<Subscript>0.7</Subscript>(NaI)<Subscript>0.3</Subscript> solid polymer electrolyte

Solid polymer electrolytes (SPE) based on poly-(vinyl alcohol) (PVA)_0.7 and sodium iodide (NaI)_0.3 complexed with sulfuric acid (SA) at different concentrations were prepared using solution casting technique. The structural properties of these electrolyte films were examined by X-ray diffraction (XRD) studies. The XRD data revealed that sulfuric acid disrupt the semi-crystalline nature of (PVA)_0.7(NaI)_0.3 and convert it into an amorphous phase. The proton conductivity and impedance of the electrolyte were studied with changing sulfuric acid concentration from 0 to 5.1 mol/liter (M). The highest conductivity of (PVA)_0.7(NaI)_0.3 matrix at room temperature was 10⁻⁵ S cm⁻¹ and this increased to 10⁻³ S cm⁻¹ with doping by 5.1 M sulfuric acid. The electrical conductivity (σ) and dielectric permittivity (ε′) of the solid polymer electrolyte in frequency range (500 Hz–1 MHz) and temperature range (300–400) K were carried out. The electrolyte with the highest electrical conductivity was used in the fabrication of a sodium battery with the configuration Na/SPE/MnO₂. The fabricated cells give open circuit voltage of 3.34 V and have an internal resistance of 4.5 kΩ.     

Electrical and structural properties of poly (ethylene oxide)/silver triflate polymer electrolyte system dispersed with MgO nanofillers

Solvent-free films of poly (ethylene oxide)–silver triflate (PEO–AgCF₃SO₃)/MgO-based nanocomposite polymer electrolytes (PEO)₅₀AgCF₃SO₃–x wt.% MgO (x = 1, 3, 5, 7, and 10) obtained using solution casting technique were found to exhibit an appreciably good complexation of MgO nanofiller within the polymer electrolyte system and non-Debye type of relaxation as revealed by Fourier transform infrared and complex impedance analyses. Optimized filler (5 wt.% MgO) when incorporated into the polymer electrolyte resulted in a maximum electrical conductivity of 2 × 10⁻⁶ S cm⁻¹ in conjunction with a silver ionic transference number (t _Ag+) of 0.23 at room temperature (298 K). Detailed structural, thermal, and surface morphological investigation indicated a slight reduction in the degree of crystallinity owing to the addition of MgO nanofiller.     

Conductivity studies of poly(ethylene oxide)(PEO)/poly(vinyl alcohol) (PVA) blend gel polymer electrolytes for dye-sensitized solar cells

Poly(ethylene oxide)(PEO)–poly(vinyl alcohol) (PVA) blend-based gel polymer electrolytes (GPEs) have been prepared by blending equal weights of PEO and PVA in ethylene carbonate (EC), dimethyl sulfoxide (DMSO), tetrabutylammonium iodide (TBAI), and iodine crystals (I₂). The conductivity, diffusion coefficient, number density, and ion mobility of the electrolytes have been calculated from the impedance data obtained from electrochemical impedance spectroscopy (EIS) measurements. The GPE with the composition of 7.02 wt%, PVA, 7.02 wt% PEO, 30.11 wt% ethylene carbonate (EC), 30.11 wt% DMSO, 24.08 wt% TBAI and 1.66 wt% I₂ exhibits the highest conductivity of 5.5 mS cm^?1 at room temperature. Dye-sensitized solar cells (DSSCs) with configuration fluorine tin oxide (FTO)/titanium dioxide/N3-dye/GPE/platinum/FTO have been fabricated and tested under the white light of intensity 100 mW cm^?2. The DSSC containing the highest conducting GPE exhibits the highest power conversion efficiency, η of 5.36 %.     

Structural investigation on PEO-based polymer electrolytes dispersed with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

Thin solid polymer electrolytes based on polyethylene oxide (PEO) and silver triflate (AgCF₃SO₃) dispersed with various concentrations of aluminum oxide (Al₂O₃) nanoparticles have been prepared by solution casting technique. These thin polymer films are found to have thickness of the order of 30 to 100 μm. The X-ray diffraction (XRD) patterns have indicated the amorphous nature of the polymer electrolyte. The differential scanning calorimeter (DSC) traces showed slight change in the glass transition temperature (T _g) whereas the degree of crystallization (X _c) decreases markedly due to the addition of alumina nanoparticles. Fourier transform infrared (FTIR) spectral analysis of all these samples has revealed the presence of absorption bands around 1,000 cm⁻¹; thus indicating the complexation of silver ions with oxygen in PEO. Employing the Wagner’s polarization technique as the standard method, the total ionic transference number for the complexed polymer electrolyte was found to be approximately unity thereby revealing that the significant contribution to electrical conduction was due to ions only. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006     

Cells studies on PEO/PEG/NaClO<Subscript>3</Subscript> thin-film electrolyte system based on composite V<Subscript>2</Subscript>O<Subscript>5</Subscript> electrode

The thin-film solid polymer electrolyte based on polyethylene oxide (PEO) with sodium chlorite (NaClO₃) has been prepared by a solution-cast technique. The electrolyte was characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry, alternating current conductivity, and Wagner’s polarization studies. The complexation of NaClO₃ with PEO was confirmed through the XRD and IR studies. The transference number measurement has shown that the ion transport is predominant over electrons in the polymer electrolytes (t _ions ≈ 0.94). The conductivity enhancement was observed in the case of the PEO/NaClO₃ system with the addition of plasticizers (low-molecular-weight polyethylene glycol, organic solvents propylene carbonate and dimethyl formamide. Cyclic voltammetry analysis showed the stability and redox character of the electrolyte and electrode. Finally, polymer electrolyte systems were examined by electrochemical cell studies using V₂O₅ and composite V₂O₅ cathode at temperature of 35 °C. Overall, the plasticized electrolyte shows a better electrochemical performance, and a higher discharge capacity was observed in composite V₂O₅-based cells over V₂O₅-based cells.     

Role of composite MnO2 cathode on electrochemical cells based on polymer electrolyte (PEO/NaClO3)

Thin-film sodium-ion-conducting polymer electrolyte based on polyethylene oxide (PEO) system was prepared by solvent casting method. The thin-film electrolytes were characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry (CV) and alternating current conductivity, and Wagner’s polarization method. The complexation of salt with PEO was confirmed by XRD and IR studies. The charge transport of these electrolytes is mainly due to ions, which was confirmed by the transference number experiment. The conductivity studies show that the conductivity value of PEO/NaClO₃ complex increases with the increase of temperature as well as the addition of low molecular weight polyethylene glycol, dimethyl formamide, and propylene carbonate. The electrolyte stability and cell reversibility were analyzed by CV studies. Electrochemical cells have been fabricated with a common cell configuration Na|electrolyte|(MnO₂ + I₂ + C + electrolyte), and their discharge characteristic studies were made through a load 100 kΩ at room temperature. The measured open circuit voltage ranges from 2.80 to 2.54 V with short circuit current ranges from 667 to 1,000 μA and several other cell parameters were evaluated. Finally, the merit of the composite cathode is found with the comparison of the MnO₂ cathode.     

Morphology,chemical interaction,and conductivity of a PEO-ENR50 based on solid polymer electrolyte

A solid polymer electrolytes (SPE) comprising blend of poly(ethylene oxide; PEO) and epoxidized natural rubber as a polymer host and LiCF₃SO₃ as a dopant were prepared by solution-casting technique. The SPE films were characterized by field emission scanning electron microscopy to determine the surface morphology, X-ray diffraction, and differential scanning calorimeter to determine the crystallinity and thermogravimetric analysis to confirm the mass decrease caused by loss of the solvent. While the presence of the complexes was investigated by reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Electrochemical impedance spectroscopy was conducted to obtain ionic conductivity. Scanning electron microscopy analysis showed that a rough surface morphology of SPE became smoother with addition of salt, while ATR-FTIR spectroscopy analysis confirmed the polymer salt complex formation. The interaction occurred between the salt, and ether group of polymer host where the triple peaks of ether group in PEO merged and formed one strong peak at 1,096 cm⁻¹. Ionic conductivity was found to increase with the increase of salt concentration in the polymer blend complexes. The highest conductivity achieved was 1.4 × 10⁻⁴ Scm⁻¹ at 20 wt.% of LiCF₃SO₃, and this composition exhibited an Arrhenius-like behavior with the activation energy of 0.42 eV and the preexponential factor of 1.6 × 10³ Scm⁻¹.     

Ni-MH battery based on plasticized alkaline solid polymer electrolytes

Solid-state nickel metal hydride cells were fabricated using plasticized alkaline solid polymer electrolytes (ASPE) prepared from polyvinyl alcohol (PVA), potassium hydroxide (KOH), alumina (α-Al₂O₃), and propylene carbonate (PC). The ASPE film with PVA/KOH/α-Al₂O₃/PC/H₂O weight ratio of 1.00:0.67:0.09:2.64:1.32 and conductivity of (6.6 ± 1.7) × 10⁻⁴ S cm⁻¹ was used in fabrication of the electrochemical cells. To investigate the electrochemical properties of the plasticized ASPE, cells with the configuration Mg₂Ni/plasticized ASPE/Ni(OH)₂ were fabricated. At the eighth cycle with a current drain of 0.1 mA and plateau voltage of ∼1.1 V, the discharge lasted for 14 h before the cell was considered to have failed. The failure mode of the cell was due to the formation of thin Mg(OH)₂ insulating layers.     

Organic dopant added polyvinylidene fluoride based solid polymer electrolytes for dye-sensitized solar cells

The effect of phenothiazine (PTZ) as dopant on PVDF/KI/I₂ electrolyte was studied for the fabrication of efficient dye-sensitized solar cell (DSSC). The different weight percentage (wt%) ratios (0, 20, 30, 40 and 50%) of PTZ doped PVDF/KI/I₂ electrolyte films were prepared by solution casting method using DMF as a solvent. The following techniques such as Fourier transform infrared (FT-IR), differential scanning calorimetry (DSC), X-ray diffractometer (XRD) and AC-impedance analysis have been employed to characterize the prepared polymer electrolyte films. The FT-IR studies revealed the complex formation between PVDF/KI/I₂ and PTZ. The crystalline and amorphous nature of polymer electrolytes were confirmed by DSC and XRD analysis respectively. The ionic conductivities of polymer electrolyte films were calculated from the AC-impedance analysis. The undoped PVDF/KI/I₂ electrolyte exhibited the ionic conductivity of 4.68×10⁻⁶ S cm⁻¹ and this value was increased to 7.43×10⁻⁵ S cm⁻¹ when PTZ was added to PVDF/KI/I₂ electrolyte. On comparison with different wt% ratios, the maximum ionic conductivity was observed for 20% PTZ-PVDF/KI/I₂ electrolyte. A DSSC assembled with the optimized wt % of PTZ doped PVDF/KI/I₂ electrolyte exhibited a power conversion efficiency of 2.92%, than the undoped PVDF/KI/I₂ electrolyte (1.41%) at similar conditions. Hence, the 20% PTZ-PVDF/KI/I₂ electrolyte was found to be optimal for DSSC applications.     

Conductivity studies of plasticized anhydrous PEO-KOH alkaline solid polymer electrolyte

Polyethylene oxide (PEO)–potassium hydroxide (KOH)-based alkaline solid polymer electrolyte films have been prepared by using methanol as solvent. The highest room temperature ionic conductivity of (2.1 ± 0.5) × 10⁻⁸ S cm⁻¹ was achieved for the composition of 70 wt% PEO:30 wt% KOH. The addition of plasticizer, ethylene carbonate, propylene carbonate, or polyethylene glycol to the highest conductivity of PEO–KOH system helps to increase the ambient ionic conductivity to the order of 10⁻⁶–10⁻⁴ S cm⁻¹. The log σ vs 1/T plot of PEO–KOH showed a small conductivity decrease at 50–60 °C range. The small decrease and the hysteresis that occur during the heating–cooling cycle was overcome by the presence of the plasticizer. X-ray diffraction observation supports the conductivity results.     

Transport properties of hexanoyl chitosan-based gel electrolyte

Films of hexanoyl chitosan-based polymer electrolyte were prepared by the technique of solution casting. The effect of plasticizer on the transport properties of hexanoyl chitosan:lithium trifluoromethanesulfonate (LiCF₃SO₃) electrolytes have been investigated. The plasticizer used was ethylene carbonate (EC). The highest room temperature conductivity achieved in the EC-plasticized hexanoyl chitosan-based electrolytes is 2.75×10⁻⁵ S cm⁻¹. The Rice and Roth model was used to explain the variations in the dc conductivity observed. The exponent, s, in Jonscher’s universal power law equation σ(ω)=σ _dc+Aω ^s , was analyzed as a function of temperature for the sample containing 30 wt% of EC. The analysis suggests that the conduction mechanism follows that proposed by the overlapping large polaron tunneling model.     

Experimental investigations on poly(ethylene oxide) based sodium ion conducting composite polymer electrolytes dispersed with SnO2

New Na⁺ ion conducting composite polymer electrolytes comprising of polyethylene oxide (PEO)-NaClO₄ and PEO-NaI complexes dispersed with SnO₂ are reported. The results of the studies based on optical microscopy, X-ray diffraction (XRD), differential scanning calorimetry (DSC), Fourier transform infra-red (FTIR) spectroscopy, impedance analysis and mechanical testing are presented and discussed. The electrical conductivity of ≈5·10⁻⁵ S·cm⁻¹ at 40 °C was achieved for the dispersion of ≈10 wt.% of SnO₂ in both systems. The composition dependence of the conductivity has been well correlated with the variation in glass transition temperature and degree of crystallinity. A substantial enhancement in the mechanical properties of the composite films was observed at the cost of slight decrease in the conductivity at higher concentration of SnO₂. The temperature dependence of the conductivity follows apparently the Arrhenius type thermally activated process below and above the melting temperature of PEO. The conductivity of the materials has been found to be strongly humidity dependent. The materials are shown to be ionic with t_ion>0.9. The electrochemical stability of the materials has been observed to be up to ≈3.2 V for (PEO)₂₅NaClO₄+x% SnO₂ and is limited to ≈1.9 V for (PEO)₂₅NaI+x% SnO₂.     

Gelatin-based protonic electrolyte for electrochromic windows

Proton-conducting gel polymer electrolytes based on gelatin plasticized with glycerol and containing acetic acid were investigated, characterized, and applied to electrochromic window. For glycerol contents varying from 7% to 48%, the conductivity of the uniform and predominantly amorphous gel electrolyte was found to follow a Vogel–Tamman–Fulcher behavior with the temperature. Typically, for the electrolyte chosen to make 7 × 2 cm² electrochromic smart window with the configuration: glass/fluor-doped tin oxide (FTO)/WO₃/gelatin electrolyte/CeO₂–TiO₂/FTO/glass and containing 28% of glycerol, the conductivities were found to be of the order of 5 × 10⁻⁵ S/cm at room temperature and 3.6 × 10⁻⁴ S/cm at 80 °C. The device was characterized by spectroelectrochemical techniques and was tested up to 10,000 cycles showing a fast coloring/bleaching behavior, where the coloring process was achieved in 10 s and the bleaching in 2 s. The transmission variation at the wavelength of 550 nm was about 15%. The cyclic voltammograms showed a very good reversibility of the cathodic/anodic processes, and the charge density was about 3.5 mC/cm². The memory tests showed that the transmittance in the colored state increased by 8% in 90 min after removing the potential.     

Effect of lithium salt concentration in PVAc/PMMA-based gel polymer electrolytes

Hybrid solid polymer electrolyte films comprising of poly(vinyl acetate) (PVAc), poly(methyl methacrylate) (PMMA), LiClO₄, and propylene carbonate are prepared by solution casting technique by varying the salt concentration. In this study, PVAc/PMMA polymer blend ratio is fixed as 25:75 on the basis of conductivity and mechanical stability of the film. X-ray diffraction, Fourier transform infrared impedance, thermogravimetry/differential thermal analysis and scanning electron microscopy studies are carried out for the polymer electrolytes. The maximum ionic conductivity is found to be 4.511 × 10⁻⁴ S cm⁻¹ at 303 K for the plasticized polymer electrolyte with 8 wt.% of LiClO₄. The ionic conductivity is found to decrease with an increase of LiClO₄ concentration.