TW Laser system for Thomson scattering X-ray light source at Tsinghua University

A TW (Tera Watt) laser system based on Ti:sapphire mainly for the Tsinghua Thomson scattering X-ray light source (TTX) is being built. Both UV (ultraviolet) laser pulse for driving the photocathode radio-frequency (RF) gun and the IR (infrared) laser pulse as the electron-beam-scattered-light are provided by the system. Efforts have also been made in laser pulse shaping and laser beam transport to optimize the high-brightness electron beam production by the photocathode RF gun.     

光阴极微波电子枪中时间抖动对粒子动力学的影响

对光阴极微波电子枪粒子束性能起决定性影响的因素之一就是激光脉冲相对加速微波相位的时间抖动. 对这种时间抖动的测量和反馈控制进行了理论和实验分析, 并对时间抖动对束流品质的影响进行了模拟研究, 得到了利用锁相环回路降低激光脉冲相位噪声的实验经验, 为光阴极微波电子枪中激光与微波相位同步问题提出了解决方法.     

光阴极微波电子枪驱动激光整形与传输系统

为满足合肥先进光源对高品质注入束流的要求,合肥先进光源预研项目研制了一套光阴极微波电子枪系统作为注入器电子源。为降低空间电荷效应引起的束流发射度增长,对驱动激光整形及传输系统进行了理论和实验研究。通过双折射晶体的脉冲时间整形以及采用光阑高斯截断的空间整形,得到了近似均匀分布的激光脉冲。像传递激光传输光路,实现了光阴极表面激光位置的高稳定性。实验结果显示,光阴极表面的激光位置抖动小于4 μm,激光性能满足实验要求。     

Studies on a Laser Driven Photoemissive High-Brightness Electron Source and Novel Photocathodes

A laser driven photoemissive high-brightness electron source at Peking University is reported.Through a DC accelerating gap of 100kV voltage,the device is capable of delivering high-brightness electron beam of 35—100ps pulse duration when irradiated with a mode-locked YAG laser.The geometry of the gun is optimized with the aid of simulation codes EGUN and POISSON.The results of experimental studies on ion implanted photocathode and cesium telluride photocathode are given.The proposed laser driven superconducting RF gun is also discussed.     

Bunch length measurement at Tsinghua Thomson scattering X-ray source

The length of electron beam from a photocathode RF gun is determined by a spectrometer, according to the relative energy spread induced by the bunch length during the acceleration in a linac. For a photocathode RF gun, different laser injected phase and beam charge are studied. The compression is changed for the different laser phases, as from 10° to 30°, and the bunch length is lengthened due to the strong longitudinal space charge force, caused by the increased charge.     

Genetic-algorithm-based method to optimize spatial profile utilizing characteristics of electrostatic actuator deformable mirror

Arbitrary spatial beam shaping was demonstrated with a membrane electrostatic actuator type deformable mirror (DM). An automatic closed loop system must optimize such beam shapes as flattop. Well-characterized short pulse laser beam is widely required for a photocathode RF gun or for microscopic processing, etc. We propose a new sophisticated optimizing method based on a genetic algorithm (GA) for spatial shaping. A membrane type DM is driven by electrostatic attraction power, and applied electrode voltages vs displacement of membrane surface have a square function relationship. We prepare discrete electrode voltages to linearly change displacement as a utilized gene of the initial population in GA. Using uniform crossover without mutation in this method, we can make an arbitrary spatial beam shape quasi-flattop.     

激光斜入射光阴极对束流质量的影响及其优化

 针对美国布鲁克海文国家实验室（BNL）型的光阴极微波电子枪,模拟了不同分布状态的驱动激光脉冲斜入射光阴极对束流质量的影响,给出了改变注入相位和补偿线圈磁场强度对发射度的优化结果。结果表明：光斑椭圆化将会导致发射度的大幅增长,优化效果不理想;波前不同步导致的发射度增长对于纵向高斯分布的脉冲可以得到理想的优化。对于斜入射引起的光斑椭圆化和波前不同步问题给出了光学校正方法及部分测量结果。此外,模拟结果显示,对于横向均匀分布的激光脉冲,适当椭圆度的光斑比圆形光斑更有利于提高电子束质量。     

光阴极微波电子枪优化设计的考虑

对光阴极微波电子枪进行了优化设计 ,给出了光阳极微波腔的形状、电参数和电场分布 .电子束团初始参数对束流横向发射度的影响 ,用 Parmela程序对其进行了优化 ,得到了一组最优参数 .考虑了补偿线圈对束流发射度的影响 ,对线圈的位置和电流的大小做了优化 .经过优化后得到腔出口处的横向发射度为 1 .39πmm.mrad,达到了设计时的要求. A 1.3 GHz photocathode RF gun is under study in peking University. The photocathode RF gun, composed of gun cavity, photocathode and Laser system, is expected to deliver a electron beam with a normalized transverse rms emittance of 1π mm·mrad at a charge of 1nC. Its performance has been studied by the space-charge tracking code PARMELA. The influences of the initialized electron beam were also studied. The emittance compensation technique is employed. After optimization of the parameters was...     

RF deflecting cavity for bunch length measurement in Tsinghua Thomson scattering X-ray source

An RF deflecting cavity used for bunch length measurement has been designed and fabricated at Tsinghua University for the Thomson Scattering X-Ray Source.The cavity is a 2856 MHz,π-mode,3-cell standing-wave cavity,to diagnose the 3.5 MeV beam produced by photocathode electron gun.With a larger power source,the same cavity will again be used to measure the accelerated beam with energy of 50 MeV before colliding with the laser pulse.The RF design using MAFIA for both the cavity shape and the power coupler is reviewed,followed by presenting the fabrication procedure and bench measurement results of two cavities.     

汤姆逊硬X射线源中锁模脉冲激光稳频方法

 汤姆逊硬X射线源中，光阴极微波电子枪要求触发激光脉冲与腔中微波场相位的精确时间同步。理论分析了锁模脉冲激光器相位噪声，探讨了对激光脉冲相位探测和控制的方法，并通过实验构建了激光相位抖动测量系统和锁相环稳频回路，用基频鉴相信号驱动压电陶瓷晶体改变谐振腔长，实现了从开环3.42 ps到闭环1.46 ps的均方根相位抖动的测量和控制。     

DC-SC光阴极注入器的束载实验的调试进展

 北京大学射频超导实验室设计了新型超导光电子枪——DC-SC光阴极注入器，目标是为自由电子激光平台提供能量在2~3MeV，脉宽小于10ps，脉冲重复频率为81.25MHz，平均流强约为1mA的低发射度电子束。现在已经建成了DC-SC光阴极注入器实验平台，包括激光驱动光阴极系统，Pierce直流高压加速结构，1.3GHz 1＋1/2纯铌超导腔，恒温器低温系统，4.5kW连续波微波系统，1/16分频与同步控制系统，束流诊断系统和能量分析系统等。并且完成了超导腔的静态实验，直流加速结构也经过了100μA低电流测试。实验结果符合设计要求，整体调试后即可以进行束载实验。     

Bunch length measurement using a traveling wave RF deflector

RF deflectors can be used for bunch length measurement with high resolution. This paper describes a completed S-band traveling wave RF deflector and the bunch length measurement of the electron beam produced by the photocathode RF gun of the Shanghai DUV-FEL facility. This is the first time that such a transverse RF deflector has been developed and used to measure the bunch length of picosecond order in China. The deflector's VSWR is 1.06, the whole attenuation 0.5 dB, and the bandwidth 4.77 MHz for VSWR less than 1.1. With a laser pulse width of 8.5 ps, beam energy of 4.2 MeV, and bunch charge of 0.64 nC, the bunch lengths for different RF input power into the deflector were measured, and an averaged rms bunch length of 5.25 ps was obtained. A YAG crystal is used as a screen downstream of the deflector, with the calibrated value of 1 pix = 136 μm.     

超快电子衍射装置的束流能量反馈控制

上海交通大学的超快电子衍射(UED)装置由一台电子直线加速器作为驱动,电子枪为一台光阴极微波电子枪。加速器在运行中电子枪会偶尔打火,腔体失谐,造成束流损失,束流能量产生变化,束流需要很长时间才能恢复到初始状态,影响了用户的使用。为此,对低电平控制器(LLRF)的幅度相位控制环路进行了改进,增加了能量反馈,代替了幅度反馈,通过对束流的中心位置进行实时的反馈以控制低电平控制器输出信号的幅度,保证了电子束流的能量稳定和电子枪加速场强的稳定。长时间的稳定性测试表明,电子枪在打火产生时,束流能量可以很快恢复,能量抖动由4.2933×10^-4(RMS)提高到2.8557×10^-4(RMS),实现了束流能量的长期稳定。     

W–band光注入器的模拟研究

模拟研究了1.6个腔、高梯度的W-band光阴极微波电子枪系统,该系统能产生和加速300pC的电子束团.设计系统由频率91.392GHz光阴极微波电子枪以及频率91.392GHz行波加速结构组成.基于射频直线加速器标度律与数值模拟结果,设计系统能产生能量1.74MeV,电量300pC,束团长度0.72ps,归一化横向发射度0.55mm·mrad的电子束团.研究了高频、高梯度下的束流动力学.由于高梯度,有质动力效应在束流动力学中起重要作用,且由于横向与纵向之间的耦合,在基次空间谐波的情形下,仍然存在着有质动力聚焦效应.     

Emittance measurement & optimization for the photocathode RF gun with laser profile shaping

The Laser Undulator Compact X-ray source(LUCX) is a test bench for a compact high brightness X-ray generator,based on inverse Compton Scattering at KEK,which requires high intensity multi-bunch trains with low transverse emittance.A photocathode RF gun with emittance compensation solenoid is used as an electron source.Much endeavor has been made to increase the beam intensity in the multi-bunch trains.The cavity of the RF gun is tuned into an unbalanced field in order to reduce space charge effects,so that the field gradient on the cathode surface is relatively higher when the forward RF power into gun cavity is not high enough.A laser profile shaper is employed to convert the driving laser profile from Gaussian into uniform.In this research we seek to find the optimized operational conditions for the decrease of the transverse emittance.With the uniform driving laser and the unbalanced RF gun,the RMS transverse emittance of a 1 nC bunch has been improved effectively from 5.46 πmm.mrad to 3.66 πmm.mrad.     

Photoinjector beam quality improvement by shaping the wavefront of a drive laserwith oblique incidence

To increase the quantum efficiency (QE) of a copper photocathode and reduce the thermal emittance of an electron beam, a drive laser with oblique incidence was adopted in a BNL type photocathode rf gun. The disadvantageous effects on the beam quality caused by oblique incidence were analyzed qualitatively. A simple way to solve the problems through wavefront shaping was introduced and the beam quality was improved.     

Emittance measurement & optimization for the photocathode RF gun with laser profile shaping

The Laser Undulator Compact X-ray source(LUCX) is a test bench for a compact high brightness X-ray generator,based on inverse Compton Scattering at KEK,which requires high intensity multi-bunch trains with low transverse emittance.A photocathode RF gun with emittance compensation solenoid is used as an electron source.Much endeavor has been made to increase the beam intensity in the multi-bunch trains.The cavity of the RF gun is tuned into an unbalanced field in order to reduce space charge effects,so that ...     

Experimental verification of laser photocathode RF gun as aninjector for a laser plasma accelerator

The feasibility of the laser photocathode RF gun, BNL/GUN-IV, as an injector for a laser plasma accelerator was investigated at the subpicosecond S-band twin linac system of the Nuclear Engineering Research Laboratory, University of Tokyo. Electron beam energy of 16 MeV, emittance of 6π mm mrad, bunch length of 240 fs (FWHM), and charge per bunch of 350 pC were confirmed at 10 Hz. As for diagnosis of the femtosecond electron bunch, the quantitative comparison of performance of the femtosecond streak camera, the coherent transition radiation (CTR) Michelson interferometer, and the far-infrared polychromator was carried out. We concluded that the streak camera is the most reliable up to 200 fs and that the polychromator is the best for the shorter electron bunch. The 3.5-ps (rms) resolved synchronization between the YLF laser driver for the gun and the electron bunch was achieved. Based on the above experiences, we have designed and installed a much better laser-electron synchronization system using the Kerr-lens mode-locked Ti:Sapphire laser with the min harmonics synchrolocker and the stable 15-MW klystron. The timing jitter is expected to be suppressed down to 320 fs (rms)     

新型跑道腔式束流位置监测器

系统提出了一种新的腔式束流位置监测器(BPM),即跑道型腔式BPM,并使用微波工作室软件进行了理论研究和模拟计算,提出了通用设计方法。跑道型腔式BPM的金属腔部分具有跑道形横截面,引出束流位置偏移激励起的一对偶极模式作为束流位置信号。该方案的偶极模式极化方向固定,频率分离,可以解决随机误差产生的横向串扰问题,其理论位置分辨力可以达到15 nm。     

强流目标的DC-SRF-II光阴极驱动激光系统设计

为推动北京大学超导加速器实验装置不断向强流目标迈进,提出100 W红外高重频光阴极驱动激光的设计方案,主放大器采用先进的光子晶体增益光纤,保证输出光束的质量。对激光系统中的关键问题,如各部分功率指标、脉冲展宽和压缩、激光耦合等进行了设计,并且考虑了激光的非线性影响。为实现强流加速器开机运行所必备的诊断模式,也提出了对于高重频激光进行两级选频的独特设计方案。将高速的SOA光开关和低速的声光调制器相结合,产生宏脉冲结构的输出激光,从而实现加速器在诊断模式下的运行。